27th IAEA Fusion Energy Conference - IAEA CN-258

22 Oct 2018, 08:30 → 27 Oct 2018, 18:45 Asia/Kolkata

Mahatma Mandir Conference Centre

FEC 2018 CONFERENCE MATERIAL

Fusion Energy Conference 2018 Reviews Status of Research and Technology to Fusion Power

Fusion Energy Conference 2018: Can We Harness the Energy that Powers the Sun?

The 27th IAEA Fusion Energy Conference is being organized by the IAEA in cooperation with the Department of Atomic Energy, Government of India and the Institute for Plasma Research, at the Mahatma Mandir, Gandhinagar (Ahmedabad) Gujarat, India.
 

Previous conferences in this series were held in Salzburg (1961), Culham (1965), Novosibirsk (1968), Madison (1971), Tokyo (1974), Berchtesgaden (1976), Innsbruck (1978), Brussels (1980), Baltimore (1982), London (1984), Kyoto (1986), Nice (1988), Washington DC (1990), Würzburg (1992), Seville (1994), Montreal (1996), Yokohama (1998), Sorrento (2000), Lyon (2002), Vilamoura (2004), Chengdu (2006), Geneva (2008), Daejeon (2010), San Diego (2012), Saint Petersburg (2014) and Kyoto (2016).

---

Affiliations Shortcut names for author affiliations

Conference Poster & Flyer FEC2018_Flyer.pdf FEC2018_Poster.pdf

Forms A,B (word) word file word file

Templates Template for preprints to be published on the Conference material

Monday, 22 October

O/1 Opening

1 Traditional Lightning of the Lamp

2 Opening Address

Speaker: Ms MEERA VENKATESH (INTERNATIONAL ATOMIC ENERGY AGENCY)

3 Welcome Address

Speaker: Host Country Representative (India)

4 Importance of Energy and the role of Nuclear Energy in India’s Energy Mix

For the past ten years, cumulative average growth rate for electricity generation in India has been close to 6%. During the year 2016-17, total electricity generation was about than 1430 billion kW-hour or TW-hour. It will be more than 1500 TW-hour in 2017-18. Considering rate of economic growth, linkage between economic growth and electricity requirements, increasing urbanisation and current low per capita electricity availability, electricity generation in India is likely to exceed 8000 TW-hour by the middle of this century. Environmental sustainability enjoins on India to generate a significant fraction of the total generation by low-carbon technologies that is nuclear, hydro, solar and wind. Considering that total potential of hydro, solar and wind is only about one-fourth of the projected electricity requirements, nuclear must play a dominant role.

The talk will explain near- and medium-term plans to accelerate growth in installed nuclear capacity, and provide a glimpse of ongoing research and development aimed at directing growth in installed capacity in the long-term.

Speaker: Ravi B. Grover (Homi Bhabha National Institute (HBNI), Anushakti Nagar, Mumbai 400094, India)

Grover FEC IPR.pptx

5 India’s Quest for Fusion Energy & Road to ITER

Recognizing the limitations of currently available resources, India’s quest for new energy sources is common for all nations, which are in a state of rapid growth and aspire to seek a respectable place on the global canvas of peaceful and sustainable co-existence. Lack of adequate energy denies opportunity to lead a developed and precludes realization of human potential into what it could have been. The global impact can be gauged from the fact that among the 17 Sustainable Development Goals, spelt out after an extensive study by the UN, the 7th Goal is about ‘affordable and clean energy’. Today or in very near future – the whole world is or will be in a situation that will require every conceivable energy source to be tapped, improved in efficiency, made cost-effective and be equipped with a method to mitigate any adverse impact on the environment.

In spite of India’s taking significant steps towards tapping every bit of both conventional and renewable energy sources, the demand is much higher than what is currently available and is still growing. If one takes a grand challenge of bringing parity with the world-average for the per capita consumption, the capacity has to be trebled! How fast can one add ~400 GW? No matter what we do and however staggering this figure is, there is no going back from this target. So, an equally challenging problem that emerges is how do we manage to grow on sub-optimal energy supply in the interim period. Techniques to reduce energy consumption by increasing efficiency of various processes need to be developed. For this one needs new tools, materials and research-infrastructure to innovate, improvise and harness the benefits of improvement on a mass-scale. Scales matter; even a tiny saving/improvement for a nation with billion people is quite impactful.

Advanced technologies like fusion hold the promise but have been traditionally considered too far away for any serious investment so far. The ‘fear factor’ of failure can be overpowering for policy makers. However, it’s time to turn it around and ask ourselves: What difference will it make if fusion reactor works as desired? Well, it will make a tremendous difference. It deserves a try, just for that hope we have. The ITER Project is a collective expression of this global quest for energy in the form of the largest scientific endeavour involving more than half of the world population. The task however, is complex and embeds challenges of extreme kind. But fusion research is also all about innovative ways and can continue to provide the world with spin-offs while it graduates from hydrogen plasma to D-T and from there on to power-reactors.

India has come a long way in both fusion-science and technology via its well-conceived indigenous as well as collaborative measures. India’s journey began in 1982 and it has grown in several areas of plasma and fusion research. A number of developments has taken place: tokamaks with copper-coils (ADITYA) and with superconducting coils (SST-1) have been built indigenously in the Institute for Plasma Research, Gandhinagar. The scientists have gained enormous experience in plasma operations of these tokamaks as well as in SINP-tokamak, which is located in the Saha Institute of Nuclear Physics, Kolkata. Now, an upgraded ADITYA-U is in place capable of experiments with shaped plasma. A host of auxiliary technologies have been developed and tested with the test-beds created in-house.

India needs to sustain the momentum of its fusion research to be able to reap the benefits from participation in ITER and to quickly channelize the success of ITER in its vision. The ITER participation has been followed in India with the blanket and the divertor technology development initiatives. Industrial applications of the plasma have come off age and last but not the least, the human resource development has taken place with a strong academic back-bone. In this talk, the above-mentioned developments are overviewed and an outline of the future plan --and how it blends with ITER participation is also presented.

Speaker: Shishir Deshpande (India)

Quest_for_Fusion_Energy_FEC2018 v4.pptx

6 EU R&D Energy policy and the role of fusion research

Research and Innovation contributes to several of the ten priorities of the European Commission for 2015-19. The EU's energy research policy contributes, in particular, to provide its citizens and businesses with secure and affordable energy, while also addressing the causes of climate change.
The next Research and Innovation Programme, covering the period 2021-2027, will build on the success of the current Programme (Horizon 2020) under the guiding principle of 'evolution, not revolution'.
Intensified international cooperation under the next Programme will ensure that European researchers and innovators have access to and benefit from the world’s best talent, expertise and resources. This will, inter alia, enhance the supply and demand of innovative solutions and promote reciprocal international research partnerships.
In the area of Fusion Research the implementation of the 'Roadmap to the Realisation of Fusion Energy' will continue to be the priority focus, with a strong and continued support for the construction of ITER and a significant research effort to prepare for DEMO.

Speaker: Patrick Child (European Commission)

P. Child_Talk_IAEA FEC India 22 10 2018.pdf

7 Fusion is our Future: Readiness of the Fusion Technology and the 4th Industrial Revolution

The time and cost of further increasing the overall readiness level of fusion energy, which requires testing materials under extreme environment, data collection, analysis and new designs, can be significantly reduced with the advent of the fourth industrial revolution. The fourth industrial revolution is on its way. Known as Industry 4.0, it represents the current trend to use automation and data exchange technologies that include cyber-physical systems, the Internet of things, cloud computing and cognitive computing. These technologies are rapidly being developed to perform industry activities. Components of future fusion reactors are expected to be designed and manufactured by using advanced simulation technologies and advanced manufacturing methods. The costs will be further reduced as there will be increased harmonisation of codes and standards. IAEA have already taken steps to ensure that the design rules are harmonised before the technology is commercialised. In case of the fission technology there was commercialisation before harmonisation but for fusion technology it will be harmonisation before commercialisation.

Speaker: Nawal Prinja (AMEC Foster Wheeler)

FEC 2018 by N Prinja.pptx

10:15 Coffee Break

OV/1 Overview Magnetic Fusion

8 Progress of ITER-India activities for ITER deliverables: Challenges & Mitigation Measures

The responsibilities of ITER-India include a mix of precision, heavy, R&D intensive and interface intensive systems, under built-to-print and functional systems category. In several systems, components fall under the category of first of its kind or of the largest kind. The uniqueness of specifications lead to a challenging situation – namely that neither the existing labs or potential suppliers have ever done or encountered such scale-up (either in size/volume, capacity, precision etc.) and do not have even the R&D infrastructure to match the requirements. Under a graded approach a full-scale prototype or at an appropriate scale needs to be developed apart from the testing infrastructure. Facilities have been established to demonstrate the integrated and functional performance in the first if its kind and R&D intense systems, as a risk mitigation strategy. These include, for IC system, an extension of the successful prototype results to demonstrate the production of 2.5 MW in a double chain configuration with a combiner at the output. For Neutral Beams, development of the ion source to realize the stringent parameter space for DNB and development of special technologies, involving special copper alloy Cu-Cr-Zr and special manufacturing technologies, involving high precision of <50 micron over ~ 1 m, as the first of its kind. Additionally, development of SIC compliant isolators and ultimately, setting up of a test facility with an unique attribute to test for the beam transmission Setting up of a special cryogenic test facility to test the performance, against the designed performance for the 4 K, 50 K and 80 K Helium lines with multi process pipes. Development of a SIC compliant 140 kV class feed-through to feed 100 kV for the DNB High voltage power supplies. It is demonstrated that engineering efforts invested at the stage of prototyping have led to a significantly reduced effort in the resolving the technical issues encountered at the stage of production and manifests as a primary risk mitigation strategy in the management of ITER-India procurement. The paper presents the technical achievements and the overall status with an emphasis on the special developments for the first of its kind components to meet the challenging specifications.

Speaker: Arun Kumar Chakraborty (ITER-India, Institute for Plasma Research)

OV-1-1-AKC-FinalV2.pptx

Summary Slide-OV-1-1.pptx

9 Progress toward ITER’s First Plasma

ITER reached 50% completion of the work required to achieve First Plasma in November 2017. Progress has been made on ITER infrastructure since the 2016 FEC, most visibly the construction of many key buildings. The tokamak assembly building and the tokamak bioshield have been completed. The tokamak building will be ready for equipment in 2020. The cryogenic plant and the magnet power supply buildings are complete, and these systems begin commissioning in 2019. The power conversion and distribution area is complete and the component cooling water system building has started construction. Commissioning of these systems starts in 2018. Thus, the physical plant is moving rapidly toward completion, and key systems are entering the commissioning phase. Equally impressive is progress toward manufacturing components of the ITER tokamak. The base and lower cylinder of the cryostat have been assembled on the ITER site. The first of the six modules of the central solenoid has been wound, and three of the six poloidal field coils are presently being wound. The first winding pack of the toroidal field magnets is complete, as is the first casing, which has been verified to meet the high tolerances required (<0.5 mm). The first complete set of parts comprising a vacuum vessel sector has been fabricated and demonstrated to meet strict tolerances (<1 mm). Therefore, the major components of the tokamak have passed into the fabrication phase. The Heating and Current Drive systems (NB, ECH and ICH) are also in the final design phase. The sequence of ITER operation from First Plasma (FP) to the achievement of the Q = 10 and Q = 5 project goals has been consolidated in a Staged Approach. This is a stepwise installation of components and ancillary systems, with all systems installed before the start of the FPO operational phase. The ITER Research Plan has been revised in 2017 to be consistent with the systems available in each phase. Physics R&D focuses on the Disruption Mitigation System, design of the ITER tungsten divertor, and modelling of ITER plasma scenarios. An international Task Force has been established to coordinate R&D on disruption mitigation. Modelling concentrates on the initial phases of the Research Plan and on the Q = 10 scenario, especially plasma termination. The focus is on scenarios that access the H-mode regime in the PFPO-1 and PFPO-2 phases.

Speaker: Mr Bernard Bigot (ITER Organization)

The_ITER_Project__Construction_and_Manuf_XBSZMC_v1_1.pdf

The_ITER_Project__Construction_and_Manuf_XBSZMC_v1_1.pptx

10 Overview of the JET preparation for Deuterium-Tritium Operation

Europe has elaborated a Roadmap to the realisation of fusion energy in which ‘ITER is the key facility and its success is the most important overarching objective of the programme’. We review the contribution of the recent JET experiments with the ITER first wall materials mix, and, the underlying physics understanding to mitigate the scientific risks identified in the ITER research plan. Indeed, together with the ITER scenario development, a strong focus on JET is pursued for addressing ITER needs and developing a sound physics basis for the extrapolation through first principle and integrated modelling: plasma wall interaction, disruption mitigation (installation of a third mitigation valve), H mode access, W-control with higher electron heating (ICRH ITER-like antenna re-instated), pellet ELMs pacing with the optimised vertical high field side track. The JET ITER-Like Wall experiment provides an insight in the coupling between tokamak-plasma operation and plasma-surface interaction in the unique Be/W material environment and acts as test-bed to verify models and modelling tools for ITER. Disruptions are considered as the highest programmatic risk in the ITER Research Plan and experimental and modelling effort in Europe and JET are reviewed. High spatial resolution Doppler backscattering measurements have revealed novel insights into the development of the edge transport barrier. The operational constraints of a metal wall can prevent reaching plasma energy confinement required for QD-T=10 on ITER. Progress on JET to mitigate this risk is reported aiming at maximizing the core and pedestal performance in stationary condition with the W divertor constrain. The measured D-D neutron fluence and gamma dose rates have been successfully compared with simulations performed with the codes used for ITER nuclear safety analyses. Finally, the benefit to further use JET beyond 2020 to train the international ITER team with an upgrade tungsten divertor and with the ITER control tools will be discussed. This work has been carried out within the framework of the EUROfusion Consortium and has received funding from the Euratom research and training programme 2014-2018 under grant agreement No 633053. The views and opinions expressed herein do not necessarily reflect those of the European Commission

Speaker: Dr Emmanuel Joffrin (CEA/IRFM)

Overview-Joffrin-IAEA2018-16-9.pptx

11 DIII-D Research Towards Establishing the Scientific Basis for Future Fusion Reactors

DIII-D research is addressing critical challenges in preparation for ITER and the next generation of fusion devices through a focus on scientific investigation of plasma physics fundamentals, integration of disparate core and boundary plasma physics, and development of attractive scenarios. Fundamental studies show that including the energetic particle “kick” model in transport codes dramatically improves agreement with the measured beam ion profile during strong Alfvénic activity, while dimensionless parameter scaling studies of intrinsic rotation lead to a predicted ITER rotation profile with significant turbulence stabilization. Hard X-ray spectra measurements show that anomalous dissipation of runaway electron (RE) beams is strongest for low energy RE populations, likely due to interactions between the low energy RE population and RE-driven kinetic instabilities. Core-boundary integration studies show that the small angle slot divertor achieves detachment at lower density and extends plasma cooling across the divertor target plate, which is essential for controlling heat flux and erosion. A rotating n=2 RMP combined with a stationary n=3 RMP has demonstrated access to ELM suppression with lower 3D field strength, while at the same time dynamically controlling the divertor heat and particle flux. Other edge studies show that the higher L-H power threshold with RMP fields is potentially due to both 3D density gradient modifications and changes in ExB shear layer topology. Super H-mode experiments in the presence of ELMs have achieved near-record pedestal pressures and record stored energies for the present DIII-D configuration with βN,ped≈1.3, H98y2≈1.6-2.4 and IP≤2.0 MA. In scenario work, the ITER baseline Q=10 scenario has been advanced by adjusting the early current density profile evolution to obtain reproducibly stable operation with ≈0 external torque and without n=1 tearing modes. In the wide pedestal QH-mode regime that exhibits improved performance, the startup counter torque has been eliminated so that the entire discharge uses ≈0 applied torque and the operating space is more ITER-relevant. Finally, the high βP scenario with large-radius ITB has been extended to IP~1 MA (q95~6) with high confinement H98y2~1.6 from both Shafranov shift and negative magnetic shear. Work supported by the USDOE under DE-FC02-04ER54698.

Speaker: Dr Craig Petty (General Atomics)

Petty_IAEA_OV-1-4.pdf

Summary_Slide_OV-1-4.pdf

12:30 Lunch

OV P1-P8 Overview Posters

12 DIII-D Research Towards Establishing the Scientific Basis for Future Fusion Reactors

Speaker: Dr C. Craig Petty (General Atomics)

Petty_IAEA_OV-1-4.pdf

Summary_Slide_OV-1-4.pdf

13 ELM and ELM-control Simulations

Speaker: Dr Stanislas Pamela (CCFE - UKAEA)

14 Experiments in Disruption Avoidance for ITER Using Passive and Active Control

Speaker: Edward Strait (General Atomics)

15 NSTX-U Theory and Modeling Results

Speaker: Dr Jonathan Menard

OV-5-5R_SummarySlide.pdf

OV_R5-5.pdf

OV_R5-5.pptx

16 Overview of first Wendelstein 7-X high-performance operation with island divertor

Speaker: Prof. Thomas Klinger (Max-Planck Institute for Plasma Physics)

17 Overview of HL-2A Recent Experiments

Speaker: Mr Min Xu (Southwestern Institute of Physics)

IAEA_FEC_OV5-1_HL2A_M_Xu_one_slide.pptx

IAEA_FEC_Overview_HL2A_MinXU.pdf

IAEA_FEC_Overview_HL2A_MinXU.pptx

18 Overview of new MAST physics in anticipation of first results from MAST Upgrade

Speaker: Dr James Harrison (CCFE)

MAST_overview_summary_slide.pptx

19 Overview of Operation and Experiments in the ADITYA-U Tokamak

Speaker: Mr Rakesh Tanna (Institute For Plasma Research)

RLTanna_Poster_OV5-3_FEC_2018_A0.pdf

20 Overview of Physics Studies on ASDEX Upgrade

Speaker: Dr Hendrik Meyer (UK Atomic Energy Authority)

Meyer_OV2-1_Poster_v2.1.pdf

21 Overview of Research Results from the Alcator C-Mod Tokamak

Speaker: Dr Earl Marmar (Mass. Inst. of Technology)

IAEA18_Marmar_OV_2-4_C-Mod_25.pdf

22 Overview of the First Deuterium Experiment in LHD

Speaker: Dr Tomohiro Morisaki (National Institute for Fusion Science)

23 Overview of the JET preparation for Deuterium-Tritium Operation

Speaker: Dr Emmanuel Joffrin (CEA)

JETcontributors-IAEA2018.pdf

Joffrin-Summary-Slide-OV1-3.pptx

Overview-Joffrin-IAEA2018-16-9.pptx

24 Overview of the KSTAR research progress and future plan toward ITER and K-DEMO

Speaker: Prof. Hyeon K. Park (UNIST)

25 Overview of the Validation Activities of IFMIF/EVEDA: LIPAc, the Linear IFMIF Prototype Accelerator and LiFus6, the Lithium Corrosion Induced Facility (

Speaker: Masayoshi Sugimoto (National Institutes for Quantum and Radiological Science and Technology)

FEC2018_OV3-3_poster_Overview_the_validation_activities_IFMIF-EVEDA_Sugimoto.pdf

26 Overview of TJ-II stellarator results

Speaker: Dr Enrique Ascasibar (CIEMAT)

27 Physics research on the TCV tokamak facility: from conventional to alternative scenarios and beyond

Speaker: Dr Stefano Coda (CRPP-EPFL)

coda_overview_summary_slide.pptx

28 Progress of Indirect Drive Inertial Confinement Fusion in the US

Speaker: Dr John Kline (LANL)

Kline_IAEA_2018_presentation_final.pdf

29 Progress of ITER-India activities for ITER deliverables: Challenges & Mitigation Measures

Speaker: Arun Kumar Chakraborty (ITER-India, Institute for Plasma Research)

30 Progress of JT-60SA Project

Speaker: pietro barabaschi (f4e)

31 Progress of the CFETR Design

Speaker: Dr Guoqiang Li

IAEA_FEC_OV_I3-2_V12_20181022_for talk.pdf

32 Progress toward ITER’s First Plasma

Speaker: Mr Bernard Bigot (ITER Organization)

33 Recent advances in EAST physics experiments in support of steady-state operation for ITER and CFETR

Speaker: Dr Baonian Wan (Institute of Plasma Physics, Chinese Academy of Sciences)

34 The Strategy of Fusion DEMO In-vessel Structural Material Development

Speaker: Dr Hiroyasu Tanigawa (Japan Atomic Energy Agency)

35 Tokamak research in Ioffe Institute

Speaker: Mr Nikolai Bakharev (Ioffe Institute)

OV/2 Overview Magnetic Fusion

36 Overview of Physics Studies on ASDEX Upgrade

The ASDEX Upgrade (AUG) programme, jointly run with the EUROfusion MST1 task force, continues to enhance significantly the physics base of ITER and DEMO. Here, the full tungsten wall is a key asset for extrapolating to future devices. The high overall heating power and flexible heating mix and comprehensive diagnostic set allows studies ranging from mimicking the scrape-off-layer (SOL) and divertor conditions of ITER and DEMO at high density to fully non-inductive operation (q95=5.5, betaN<=2.8) at low density. Higher ECRH heating power <=8 MW, new diagnostics and improved analysis techniques have enhanced the capabilities of AUG. Stable high-density H-modes with Psep/R<=11 MW/m with fully detached strike-points have been demonstrated. The ballooning instability close to the separatrix has been identified as a potential cause leading to the H-mode density limit. Density limit disruptions have been successfully avoided using a path-oriented approach to disruption handling and progress has been made in understanding the dissipation and avoidance of runaway electron beams. ELM suppression with resonant magnetic perturbations (RMP) is now routinely achieved reaching HH98(y,2)<=1.1 giving new insight into the field penetration physics, in particular with respect to plasma flows. Modelling agrees well with plasma response measurements and and a helically localised ballooning structure observed prior to the ELM is evidence for the changed edge stability due to the RMP. Fast measurements of Ti and Er show that the dominantly neoclassical character of Er holds through the ELM recovery. Good agreement of 3D nonlinear MHD modelling with measured ELM crash dynamics is achieved. As type-I ELMs (even mitigated) are likely not a viable operational regime in DEMO studies of no ELM regimes have been extended. Stable I-modes up to n/nGW<=0.7 have been characterised using beta feedback. Despite the sub-Alfvenic beam energy nonlinear energetic particle modes have been observed allowing modelling comparisons under burning plasma conditions. First measurements of the eddy tilt angle of ne fluctuations using correlation Doppler reflectometry as well as the radial correlation and cross-phase angles of Te fluctuations have been achieved, showing good agreement with Gyrokinetic simulations. Dedicated matches of H, D and He discharges (core/edge) highlight important isotope physics.

Speaker: Dr Hendrik Meyer (UK Atomic Energy Authority)

Meyer_IAEA2018_ov2-1_v2_summary.pdf

Meyer_OV2-1_v4.1.pptx

Meyer_OV2-1_v4.1_small.pdf

37 Recent advances in EAST physics experiments in support of steady-state operation for ITER and CFETR

Significant progress in the development of plasma control mechanism and understanding the related physics for steady-state advanced high-performance H-mode plasmas have been achieved on EAST since the last IAEA FEC in 2016. First demonstration of >100 seconds time scale long-pulse steady-state scenario with a good plasma performance (H98(y2) ~ 1.1) and a good control of impurity and heat exhaust with the tungsten divertor has been successfully achieved on EAST using the pure RF power heating and current drive. The synergy effect between the ECH and two LHW systems (2.45GHz and 4.6GHz) on EAST has been investigated for enhanced current driven and improved confinement quality. ELM suppression using the n=1 and 2 RMPs has been achieved in EAST and applied for development of the long-pulse H-mode scenario. Reduction of the peak heat flux on the divertor was demonstrated either in a QSF configuration or using the active radiation feedback control. A fully non-inductive steady-state QSF plasma with a duration of 21s has been obtained with a reduced factor of 2.5 on the outer divertor target. Divertor particle and heat flux control using a low n rotating RMP field has been confirmed. Suppression of the W sputtering has been achieved by lowering the edge medium-Z impurity content (C, O, etc) and forming a mixture deposition on the surface of divertor target after the application of lithium wall conditioning. Disruption mitigation experiments have been studied on EAST with the application of the massive gas injection of helium or argon on the termination of initial stable target plasmas. A further increase in the total heating power and improvement of the plasma confinement are expected when using a 0-D model prediction for high bootstrap fraction (fbs~50%) regime. Preliminary 1.5-D simulations suggest that the on-axis ECRH will enhance the deposition of LHW power in the core region, which is beneficial to the effective core heating of the plasma. A new designed lower ITER-like tungsten divertor with active water-cooling is reported. With this upgrade, EAST will be capable to access the high-triangularity small-ELM H-mode regimes and also to perform the target plasma in an advanced X-divertor configuration with assistance from two new water-cooled internal PF coils in support of steady-state operation for ITER and CFETR.

Speaker: Dr Baonian Wan (Institute of Plasma Physics, Chinese Academy of Sciences)

OV2-2_EAST_Wan.pptx

Summary_OV_2018_wan v2.pptx

38 Overview of the KSTAR research progress and future plan toward ITER and K-DEMO

The KSTAR research efforts have been focused on expansion of the KSTAR operating space for ITER and K-DEMO[1], validation of critical physics and search of new physics. The operating regimes are high bp (up to ~2.8) non-inductive long pulse up to ~8s, high bN up to ~ 4.3, and k of ~2.16 and a long H-mode discharge over a minute. An improved underlying physics of resonant and non-resonant magnetic perturbation (RMP and NRMP) with the IVCC coils resulted in a long pulse edge localized mode (ELM)-crash suppressed H-mode discharge (~34s).[2] The ELM-crash suppression dependence on critical physical parameters, such as q95, d, andn was extensively investigated. Identification of the role of turbulence induced by RMPs in suppression of the ELMs identified the turbulence flow (ω_(⊥e)) physics during the RMP ramp up and down periods.[3] The study of L/H transition threshold power (Pth) dependence on the non-axisymmetric field found that the Pth is significantly affected by RMPs while NRMP components had no influence on Pth.[4] New physics of interaction between the macroscopic fluctuation (2/1 island) and micro turbulences [5] and validation of q0 issue in sawtooth instability has been explored.[6] Also the misaligned RMP configurations are used to test the divertor heat flux dispersal. [6] A major upgrade plan in KSTAR will be initiated in ~2021 for stable higher beta long pulse operation. Emphasis will be placed on a new actively cooled tungsten divertor possibly with new first wall materials and current drive (LHCD/Helicon). For the search of metal wall materials in the KSTAR upgrade plan, test of specially designed castellated tungsten block tiles of various shapes,[7] impurity transport physics experiments via injection of trace Ar and Kr gases and tungsten dust were performed. *This work is supported by the KSTAR research project funded by Korea Ministry of Science, ICT and Future Planning. References: [1] Y.K. Oh et al., FED 84 344 (2009) [2] Y. In et al., NF 55, 043004 (2015) [3] J. Lee et al., PRL, 117 (7), 075001 (2016), J. Lee et al., ibid (2018) [4] W.H. Ko et al., APS bulletin (2017) [5] J.M. Kwon et al., ibid (2018), M.J. Choi et al., NF 57, 126058 (2017) [6] Y. In et al., ibid (2018) [7] S.H. Hong et al., ibid (2018)

Speaker: Prof. HYEON KEO PARK (UNIST)

IAEA_FEC_2018_Park.pptx

OV_KSTAR__FEC_2018_PARK.pdf

OV_KSTAR_summary.pdf

39 Overview of Research Results from the Alcator C-Mod Tokamak

Alcator C-Mod has been the only divertor tokamak in the world capable of operating at magnetic fields up to 8 T, equaling and exceeding that planned for ITER. Because of its relatively compact size, C-Mod accesses regimes of extreme edge power density (1 MW/m2 average through the surface of the plasma. H-modes on C-Mod have achieved world-record tokamak volume-average and pedestal plasma pressures (

above 0.2 MPa, Pped ~ 80 kPa). The highest pedestals are obtained by accessing the super H-mode regime predicted by EPED enabling C-Mod to demonstrate Pped at 90% of the ITER target. Data from a multi-machine database shows that the boundary heat flux width scales inversely with Bp, independent of machine size. The most recent data have extended this scaling to Bp=1.3 T, beyond that envisioned for ITER, and the 1/Bp scaling persists. Based on these results, it is clear that power handling in reactors will be an even bigger challenge than in ITER, arguing for the urgent need for one or more dedicated Divertor Test Tokamaks (DTT). Laser blow-off induced cold-pulses, an enigmatic transient phenomenon that has challenged the standard local-transport paradigm, has been explained by a new local turbulent transport model. Results from the TRANSP power balance code, coupled to the quasilinear transport model TGLF-SAT1, with a new saturation rule that came about from cross-scale coupling physics, and that captures the nonlinear upshift of the critical gradient, are shown to describe the cold-pulse, including the existence of core temperature inversions at low density and disappearance at high density. A Random Forests Machine Learning algorithm, has been trained on thousands of C-Mod discharges to detect disruption events. Disruption evolution time scales on C-Mod are relatively short, and this approach gives reliable warning no more than a few ms before disruption. Warning time-scales on larger plasmas are generally longer, good news for reactor applications. Steady-state tokamak reactors will need high bootstrap fraction, supplemented by RF current drive. Lower Hybrid Current Drive is among the most efficient non-inductive techniques. Recent modeling indicates that moving the launch point to the high field side can have many benefits, including accessibility at lower n|| for higher efficiency.

Speaker: Dr Earl Marmar (Mass. Inst. of Technology)

IAEA18_Marmar_OV_2-4_C-Mod_25.pdf

40 Progress of Indirect Drive Inertial Confinement Fusion in the US

Indirect drive converts high power laser into x rays using small high-Z cavities called hohlraums. X rays generated at the hohlraum walls drive a capsule filled with DT fusion fuel. Recent experiments have produced fusion yields exceeding 50 kJ where alpha heating provides ~3x increase in yield over PdV work. Comparison of the results to the common Lawson criterion suggests the current implosions performance is ~30% from conditions expected to initiate thermonuclear gain. Improvements to close the gap on the last ~30% are challenging requiring optimization of the target/implosions and the laser to extract maximum energy. The US program has a three-pronged approach to maximize target performance each closing some portion of the gap. The first item is optimizing the hohlraum to couple more energy to the capsule while maintaining symmetry control. Novel hohlraum designs are being pursued that enable larger capsule to be driven symmetrically to both reduce 3D effects and increase energy coupled to the capsule. The second issue being addressed is capsule stability. Seeding of instabilities by the hardware used to mount the capsule and fill it with DT fuel remains a concern. Work such reducing the impact of the DT fill tubes and novel capsule mounts such as three sets of two single wire stands forming a cage, as opposed to the thin membranes currently used, are being pursed to reduce the effect of mix on the capsule implosions. There is also growing evidence native capsule seeds such as micro-structure may be playing a role on limiting capsule performance and dedicated experiments are being developed to better understand the phenomenon. The last area of emphasis is the laser. As technology progresses and understanding of laser damage/mitigation advances, increasing the laser energy to as much as 2.6 Megajoulse at 351 nm and increasing the laser power to 600 TW seems possible. This would increase the amount of energy available to couple to the capsule and allow larger capsules potentially increasing the hot spot pressure and confinement time. The combination of each of these focus areas have the potential to produce conditions to initiate thermo-nuclear ignition. The current understanding, status, and plans for near term research in each of these areas will be presented in the context of what is believed to be needed to obtain burning plasmas on NIF.

Speaker: Dr John Kline (LANL)

Kline_IAEA_2018_presentation_final.pdf

Kline_IAEA_2018_presentation_summary.pdf

OV/P P1-P8 Overview Posters

41 Activity of Indian High Heat Flux Test Facility

Plasma facing components (PFCs) of ITER-like tokamak are expected to subject high heat loads up to 10MW/m^2 during the tokamak operation in steady state condition. Selection of plasma facing materials/components required extensive qualification and testing for tokamak application. High Heat Flux Test Facility (HHFTF) plays an important role for the qualification and estimation of the life of the component under defined heat load condition. HHFTF with heat flux generated by an electron beam system having 200kW power and 45kV maximum acceleration voltage is in full-fledged operation since 2016. HHFTF is dedicated for high heat flux testing of numerous materials and plasma facing components (small & medium sized) for several thousands of thermal cycles at different heat loads. The facility is equipped with high vacuum pumping systems with pressure regulation, high pressure high temperature water circulation loop and several diagnostics devices such as pyrometers, IR-cameras, video cameras, flow, pressure and temperature sensors . This paper describes the main capabilities of the HHFTF and glimpse of various test performed on plasma facing materials and components.

Speaker: Mr SUNIL BELSARE (INSTITUTE FOR PLASMA RESEARCH)

Summary_Slide_OV-P12.pdf

42 Advances in Fusion-Relevant Physics on the Large Plasma Device

Studies of turbulence and transport in the Large Plasma Device (LAPD) have: documented the role of drift-Alfvén waves and flows in avalanche events; revealed a new instability in the edge of increased β plasmas; and demonstrated an interaction between ICRF waves and edge turbulence, leading to strong modulation of the former and enhancement of the latter. Intermittent collapses of the plasma pressure profile (avalanches) are observed with off-axis heating in LAPD and are associated with unstable drift-Alfvén waves. Flows play a critical role in the dynamics, in particular in the onset of the drift-Alfvén waves and avalanches through the interplay of the stabilizing flow shear and the destabilizing pressure gradient. Active control of the flows is obtained using biasing; this leads to control over the size and frequency of avalanches. With controlled flows, a regime is found in which avalanches are absent. Strongly electromagnetic turbulence, identified as being due to a new instability, the Gradient-Driven Drift Coupling Instability (GDC), is observed in the edge of increased β plasmas in LAPD. As the plasma beta is increased (up to 15%), magnetic fluctuations are observed to increase substantially, with δB/B ~ 1% at the highest β, while density fluctuations decrease slightly. Parallel magnetic fluctuations are observed to be dominant at the highest β, with δB∥/δB⊥~2. Comparisons of the experimental data with linear and nonlinear GENE simulations of the GDC yield good qualitative and quantitative agreement. An experimental campaign on the physics of ICRF waves on LAPD has established a correlation between strong modulation of core coupled fast waves and edge density fluctuations, both of which increase with antenna power. Strong low-frequency modulation of coupled fast wave power is observed via direct measurement of the core RF waves with magnetic probes. This modulation is well correlated with low-frequency edge density fluctuations associated with drift waves (measured with Langmuir probes). The amplitude of the RF modulation and the amplitude of edge density fluctuations in the drift wave frequency range both grow with increasing RF power, suggesting some nonlinear coupling between the edge drift waves and large amplitude fast waves in the core region.

Speaker: Prof. Troy Carter (University of California, Los Angeles)

summary_slide_TCarter.pptx

43 Design, development and recent experiments at the CIMPLE-PSI device

It is important to understand how the plasma with unparalleled heat (~10MWm-2) and ion (~1024 m-2s-1) flux will interact with the tungsten walls in the ITER tokamak, more specifically at the Divertor region of the fusion machine. Several linear magnetized plasma devices have been developed worldwide that reproduced ITER Divertor like extreme conditions for studies on relevant plasma surface interaction (PSI) issues under simulated plasma conditions. The “CPP-IPR Magnetized linear Divertor Plasma Experiment for Plasma Surface Interaction” or CIMPLE-PSI is one of the few Tokamak Divertor simulator devices that successfully reproduces both ITER-like ion and heat flux values, whose design, development and recent commissioning will be presented in this paper. A segmented plasma torch produced high-density plasma jet collimated with a maximum 0.45 Tesla axial magnetic field propagates at few Pascal chamber pressure that is maintained by four numbers of roots vacuum pumps with 14,000 m-3/h pumping capacity that interacts with a remotely placed tungsten target under controlled experimental conditions. The paper will report detailed diagnostics of the plasma jet through optical emission spectroscopic techniques (1.33 m McPherson spectrometer), a retractable Langmuir probe and water calorimeters while operating the plasma with helium and hydrogen mixture of gases. During recent PSI experiments in this device under irradiation of pure helium plasma (exposed for 1800 seconds under 0.3T magnetic field, target biased to -45 V), we had witnessed (FESEM, HRTEM) formation of surface nanotendrils in profuse amounts, recent characterization results from which also will be presented here.

Speaker: Dr Mayur Kakati (Centre of Plasma Physics-Institute for Plasma Research, Sonapur, Assam, India)

44 Formation of Hot, Stable, Long-Lived Field-Reversed Configuration Plasmas on the C-2W Device

TAE's research has been devoted to producing a high temperature, stable, long-lived field-reversed configuration (FRC) plasma state by neutral-beam injection (NBI) and edge biasing/control. C-2U experiments have demonstrated drastic improvements in particle and energy confinement properties of FRC's, and the plasma performance obtained via ~10 MW NBI has achieved plasma sustainment of up to 5 ms and plasma lifetimes of 10+ ms [1]. The emerging confinement scaling, whereby electron energy confinement time is proportional to a positive power of the electron temperature T_e, is very attractive for higher energy plasma confinement; accordingly, exploration of the observed scaling law at 10× higher T_e is one of the key research objectives. TAE's new experimental device, C-2W (also called "Norman"; the world's largest compact-toroid device), has been constructed with the following key subsystem upgrades from C-2U: (i) higher injected power (up to ~21 MW), optimum and adjustable energies (15-40 keV), and extended pulse duration (up to ~30 ms) of the NBI system; (ii) installation of inner divertors with upgraded edge-biasing electrode systems, which allow for higher biasing voltage and longer pulse operation (30+ ms); (iii) increased overall stored energy in the FRC formation pulsed-power system; (iv) fast external equilibrium/mirror-coil current ramp-up capability for plasma ramp-up and control; (v) installation of trim/saddle coils for active feedback control of the FRC plasma; and (vi) enhanced overall diagnostic suite. A remarkable side note is the fact that TAE spent only ~1 year to construct the C-2W device and produce its first plasma. C-2W experiments have already produced a dramatically improved initial FRC state after translation and merging. As anticipated by design and also in our simulations, the merged initial FRC state exhibits much higher plasma temperatures (T_e >250 eV; total electron and ion temperature >1.5 keV) and more trapped flux, providing a very attractive target for effective NBI. Edge biasing/control experiments have also demonstrated stabilization of the FRC, thereby improving plasma confinement and prolonging FRC lifetime (up to ~10 ms), in which overall plasma performance is already equivalent to or better than that obtained in C-2U. [1] H. Gota et al., Nucl. Fusion 57, 116021 (2017).

Speaker: Hiroshi Gota (TAE Technologies, Inc.)

45 Fusion Energy Development Applications Utilizing the Spherical Tokamak and Associated Research Needs and Tools

The spectrum of scientific and technological gaps that must be closed to achieve practical fusion energy using magnetically confined plasmas has been extensively documented. A common barrier to narrowing or closing these gaps is the scale and cost of fusion facilities needed to address the gaps. The low-aspect-ratio “spherical torus/tokamak” (ST) is being explored world-wide as a potentially attractive configuration for closing scientific gaps and demonstrating technical achievements on a path toward a demonstration power plant and as a more compact and/or modular fusion power source in its own right. The international fusion community is presently assessing the suitability of the ST for applications to advance fusion energy development including: developing solutions for the plasma-material-interface (PMI) challenge,fusion-fission hybrid systems, developing fusion components capable of withstanding high fusion neutron flux and fluence including breeding blankets, demonstrating electricity break-even from a pure fusion system, and electricity production at industrial levels in modular and/or larger-scale fusion power plants. This range of fusion energy development applications utilizing the ST will be described, common application-driven research needs discussed, upcoming and recently achieved ST facility capabilities and relevant highlights described, and near-term prioritized ST research directions supporting longer-term fusion energy development applications presented.

Speaker: Dr Jonathan Menard (Princeton Plasma Physics Laboratory)

Poster

• ST_FED_applications_IAEAFEC2018_poster_OVP6_v5_33x47_full.pdf
• ST_FED_applications_IAEAFEC2018_poster_OVP6_v5_single_page.pdf
• ST_FED_applications_IAEAFEC2018_poster_OVP6_v5_single_page.pptx

Summary slide Summary_slides_OVP6_v5.pdf Summary_slides_OVP6_v5.pptx

46 ITER-relevant research on the COMPASS tokamak

In the years 2016-17 the research on the COMPASS tokamak was focused on support of solution of the key challenges for the design and operation of ITER and next-step devices. This included mainly installations and upgrades of state-of-art edge plasma diagnostics, such as the new divertor probe array and the High Resolution Thomson scattering. Strong emphasis was placed on development of relevant scenarios: discharges with impurity seeding at different locations in the divertor were focused on accessing partially detached plasmas. It was demonstrated that such regime can be achieved, when nitrogen is injected at the outer target, although drop of upstream pressure was also observed. Measurements of peak ELM energy densities in the divertor complemented the existing scaling by Eich et al. and confirmed the validity of proposed model. The same set of probes mounted on the horizontal reciprocating manipulator allowed to perform upstream measurements of power decay length during ELMs. It was observed, that the power decay length exhibits a significant broadening (factor of 4) compared to the inter-ELM value. Dedicated campaigns were focused on experiments with runaway electrons (RE), studying the role of different gases (Ar, Ne, D) on the generation and mitigation of the RE beam. It appeared that an intensive injection of D may significantly slow down the current decay of RE beams triggered by Ar or Ne injection in the discharge phase with practically zero external loop voltage. On request of the ITER Organization, a unique system of COMPASS High-field-side (HFS) Resonant Magnetic Perturbation (RMP) coils was used to study the effects of Error Fields (EF) originating from misalignment or inclination of central solenoid on the plasma performance like L-H transition, H-mode performance degradation, locked modes, etc., The experimental observations are compared to predictions of the ideal MHD code IPEC. This study is being carried out in collaboration with ITER Organization and Princeton Plasma Physics Laboratory, USA. In all the aforementioned fields, a significant progress under the joint EUROfusion effort has been achieved in 2016-17 and the results complemented and broadened the existing databases.

Speaker: Dr Michael Komm (Institute of Plasma Physics of the Czech Academy of Sciences)

47 Overview and Status of Direct-Drive Inertial Confinement Fusion in the United States

Direct-drive (DD) inertial confinement fusion (ICF) offers a potential path for high yield and ignition. Two approaches – Laser Direct Drive (LDD), being pursued primarily at the OMEGA laser and the National Ignition Facility (NIF), and the Magnetized Liner Inertial Fusion (MagLIF), being pursued primarily at the Sandia National Laboratories, will be discussed in this talk. In LDD nominally identical laser beams are used to drive an imploding cryogenic shell on OMEGA to obtain high pressures and temperatures in a hot spot surrounded by a cold fuel. The goal is to obtain ignition-relevant hot-spot pressures in OMEGA-scale cryogenic deuterium–tritium layered implosions. Hot-spot pressures up to 567 Gbar have been demonstrated in these implosion experiments. In addition, recent implosion results when scaled to NIF energies are predicted to produce fusion yields approaching 300 kJ. Experiments on the NIF are additionally used to address the MegaJoule-scale physics such as laser coupling and preheat from energetic electrons. In the MagLIF approach, a 1kJ, 1TW laser pulse is used to preheat the plasma just as the 16 MA current begins to quasi-adiabatically compress the pre-magnetized deuterium. Promising ion temperatures (~ 3KeV) and neutron yields (5x1012 DD neutrons) have been obtained with MagLIF experiments at relatively low implosion speeds of ~7  106 cm/s, indicating successful magnetic flux compression and decreased thermal conductivity losses required for ignition. Ignition remains a challenge for both the direct-drive approaches, including improving understanding of the plasma conditions, controlling nonuniformity, improving laser coupling, and developing enhanced diagnostics. The motivation, challenges, and status of direct-drive research in the United States is presented in this talk. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0001944, the University of Rochester, and the New York State Energy Research and Development Authority. The support of DOE does not constitute an endorsement by DOE of the views expressed in this article.

Speaker: Bahukutumbi P. Radha (University of Rochester)

48 Overview of diagnostics upgrade and experiment progress on KTX

The Keda Torus eXperiment (KTX) is a new built middle-size reversed field pinch (RFP) device at the University of Science and Technology of China. After the long time conditioning, the favorable wall condition is achieved for implementing experiment on KTX. In present, the maximum plasma current can reach 200kA, the discharge length is beyond 20ms and the duration of typical reversed field pinch state is 2.0ms. The diagnostics on KTX has been greatly developed: 1) Total number of DAQ channel has been upgraded to 960; 2) Terahertz interferometer has been upgraded to 7 chords to obtain density and current profiles; 3) Thomson scattering with 3Joule Laser is undergoing commissioning; 4) 3D Langmuir probe system has been developed for the electromagnetic turbulence measurement; 5) 3D double-foil soft X-ray diagnostics are mounted on two poloidal sections for 3D MHD research; 6) Edge capacitive probe has been installed for the radial electrical field measurement; 7) multi-channel spectrograph system has been built for detecting impurities of carbon and oxygen. After the wall condition improvement and diagnostics upgrade, many early research such as the 3D RFP physics and electromagnetic turbulence, etc., have been conducted on KTX. The forward scattering is observed by the interferometer system which shows the potential for turbulence research with wider spectrum after improving the beam size and acceptance angle of the diagnostic beam through plasma. The research on MHD activities related with 3D RFP physics on KTX is intensely carried out with the capability upgrade of magnetic field measurement, soft X-ray tomography and high-speed visible imaging system. The electromagnetic turbulence is tentatively investigated on KTX. The 3D spectra characters of electromagnetic turbulence are firstly measured with classical two-point technique by the 3D Langmuir probe arrays, particularly in the small wavenumber range, providing the new prospect of electromagnetic turbulence in RFP plasmas. The confinement improvement of turbulence suppression is achieved in Biasing electrode experiment. The resistive MHD modelling of QSH state using NIMROD is setup in the KTX regimes. In the next step, higher performance plasma of KTX with larger plasma current, higher temperature and longer energy confinement time is expected with the capacity upgrade in the second phase.

Speaker: Prof. Wandong Liu (University of Science and Technology of China)

IAEA_2018_Summary_Liu_20180927.pdf

49 Overview of the FTU results

Since the 2016 IAEA FEC Conference, FTU operations have been mainly devoted to experiments on runaway electrons and investigations about a tin liquid limiter; other experiments have involved the elongated plasmas and dust studies. The tearing mode onset in the high density regime has been studied by means of the linear resistive code MARS and the highly collisional regimes have been investigated. New diagnostics, such as a Runaway Electron Imaging Spectroscopy system for in-flight runaways studies and a triple Cherenkov probe for the measurement of escaping electrons, have been successfully installed and tested, and new capabilities of the Collective Thomson Scattering and the Laser Induced Breakdown Spectroscopy diagnostics have been explored.

Speaker: Dr Gianluca Pucella (ENEA)

Pucella_IAEA_FEC_2018_OV_P1_Paper.pdf

Pucella_IAEA_FEC_2018_OV_P1_Poster.pdf

Pucella_IAEA_FEC_2018_OV_P1_Summary_Slide.pdf

50 Overview of the Recent Experimental Research on the J-TEXT Tokamak

Recent J-TEXT research has highlighted the significance of the role that non-axisymmetric magnetic perturbations, so called 3D magnetic perturbation (MP) fields, play in fundamentally 2D concept, i.e. tokamak. In this paper, the J-TEXT results achieved over the last two years, especially on the impacts of 3D MP fields on magnetic topology, plasma disruptions, MHD instabilities, and plasma turbulence transport, will be presented. On J-TEXT, the resonant MPs (RMPs) system, capable of providing either a static (DC) or a high frequency (up to 6 kHz) rotating (AC) non-axisymmetric MP field, has been upgraded by adding a new set of 12 in-vessel saddle coils, and the total number of in-vessel RMP coils increases from 12 to 24 (3 rows × 8 columns). The new capabilities advance J-TEXT to be a forefront of international magnetic fusion facilities, allow a flexible study of 3D effects in a tokamak. Both density and plasma rotation dependences of the m/n = 2/1 locked mode threshold, *B*_r,(2,1)^c, have been investigated systematically on J-TEXT. Recent experimental results showed the *B*_r,(2,1)^c scales linearly on the toroidal rotation, and depends weakly on plasma density, n_e. The fast rotating RMP field has been successfully applied for avoidance of mode locking and the prevention of plasma disruption. Remarkably, the rotating tearing mode was completely suppressed by the electrode biasing (EB) in addition to the RMP field. The impacts of 3D magnetic topology on the turbulences have been investigated on J-TEXT. It is found that the fluctuations of electron density, electron temperature, and plasma potential can be significantly modulated by the island structure, and a larger fluctuation level appears at the X-point of islands. The suppression of runaway electrons (REs) during disruptions is essential to the operation of ITER, and it has been reached by utilizing the 3D magnetic perturbations on J-TEXT. The NIMROD simulation indicates that the strong stochastic in the whole plasma cross-section expel out the runaway seed and results in runaway free disruptions on J-TEXT. This may provide an alternative mechanism of runaway suppression for large-scale tokamak and ITER.

Speaker: Dr Nengchao Wang (International Joint Research Laboratory of Magnetic Confinement Fusion and Plasma Physics (IFPP), AEET, SEEE, CnHUST)

FEC2018_J-TEXT_OV_P5_Final.pdf

FEC2018_J-TEXT_OV_P5_Summary_Slide.pptx

16:10 Coffee Break

FIP/1 ITER Technology

51 Completion of the first TF Coil Structure of ITER

This paper reports the completion of the first Toroidal Field Coil Structure (TFCS) of ITER of which Japan Domestic Agency (JADA) takes 100% share on procurement responsibility. The major technical challenges of the TFCS of ITER are (i) new material development for high ductility under cryogenic temperature (4K), (ii) application of partial penetration welding (PPW), (iii) welding deformation control, (iv) special ultrasonic test (UT) development considering attenuation by weldment of austenitic stainless steel and (v) fitting of large (16m x 9m) complex D-shape structure for closure welding (CW) within tight tolerance of a range of 0.5mm. Developed solutions for these challenges lead us to the successful completion of the first TF coil structure. ITER TFCS requires both high sterength and high ductility at cryogenic 4K temperature. For this, special austenitic stainless steel was newly developed. This developed material is used at inboard straight leg which supports most severe electro-magnetic force of 600MN. JADA also developed new method to keep fracture toughness requirement finding strong correlation between fracture toughness and Md30. The PPW is applied to attachments with fracture mechanics assessment using data of crack propagation under cryogenic temperature. JADA developed new UT method to apply for PPW joints, which is to obtain the position of tip of discontinuity with its continuous length and then to assess the area of deviation from nominal position compared with maximum allowable defect area obtained by fracture mechanics. The mechanical property at cryogenic temperature was checked for fracture toughness as well as yield strength of welded joints. The welding deformation was controlled by special welding process to keep balance of angular distortion. The attenuation of UT beam in the weld is compensated by transfer correction factor obtained by welding test piece made with actual material and weld metal. The TFCS was finally machined on its closure welding root that has a range of 0.5mm gap and misalignment tolerance between two welding edges. For this, quite precise control was performed such as temperature control/compensation or setting of the machining position target based on as-machined data of the other parts. As a result of fitting test, CW roots were fit and the first TFCS of the ITER was successfully completed.

Speaker: Dr Masataka Nakahira (JpQSTNFI)

Oral_CN258_FIP1-1_Completion1stTFCS_ITER_16_9ratio_r5.pptx

Presentation Oral_CN258_FIP1-1_Completion1stTFCS_ITER_16_9ratio_r5.pdf

Summary Slide CN258_FIP1-1_Completion1stTFCS_ITER_SummarySlide_r0.pdf

52 Completion of 1st ITER gyrotron manufacturing and 1 MW test result & Outcome of R&D program for ITER ICRF Power Source System & Recent progress in the development of the European 1 MW, 170 GHz CW gyrotron for ITER

A. This paper presents a summary of recent progress pertaining to the manufacturing and inspection of ITER gyrotrons and their operation system in QST. Major achievements are as follows: (i) The final design of ITER gyrotron was accomplished and manufacturing of 2 ITER gyrotrons was finished. Then their factory acceptance test (FAT) in QST has started with ITER relevant high voltage power supply configuration. The 1st ITER gyrotron has achieved 1 MW output power for 10 s pulse and 200 kW operation for 300 s which suggests thermally stable condition and sufficient cooling performance for 1 MW long pulse operation; (ii) The coupling function of gyrotron power into the transmission line (TL) waveguide was improved and calculation result of coupling efficiency was increased as high as 96.9% for the fundamental mode purity in waveguide inlet which could produce the sufficient LP01 mode purity in whole EC H&CD system. These results lead to success of ITER EC H&CD system construction toward first plasma. B. As a part of in-kind contribution, India is responsible to deliver nine numbers (1 Prototype + 8 series production) of RF Sources to ITER system, each having power handling capability of 2.5 MW/CW at VSWR 2:1 in the frequency range 35 – 65 MHz or 3.0 MW/CW at VSWR 1.5:1 in the frequency range 40 – 55 MHz, along with other stringent requirements. As there is no such amplifier chain able to meet the output power specifications as per ITER need, the RF source consists of two parallel three-stage amplifier chains, with a combiner circuit on the output side. This kind of RF source is unique in terms of its stringent specifications. A voluntary R&D program by India has been initiated for establishing the high power technology prior to Prototype and series production, using Diacrode and Tetrode tubes. In this program, single chain experimentation at 1.5MW for 2000s is conducted for the frequency range 35-65 MHz up to VSWR 2:1, with any phase of reflection coefficient. The main objective for the R&D test is to confirm the system performance for the power, duration and frequency range as per ITER need and to check the reliability of both the tube and the amplifier with matched as well as with mismatched load (up to VSWR 2:1), which essentially simulates the plasma load condition. To support the R&D program, a dedicated high power test facility has been developed at ITER-India to test RF amplifiers based on both the technologies. For Diacrode based system, high power ITER relevant tests completed in 2016 and reported elsewhere [1]. Over the past two years, assembly and integration of R&D RF source using Tetrode technology at Indian test facility is completed with validation of all the relevant sub-systems/systems as standalone mode. The high power RF test using Tetrode based RF amplifier achieved 1.7MW of power for 3600s duration at 36 MHz. For other ITER operating frequencies, the system was operated at 1.5MW/2000s successfully. This paper reports commissioning of RF amplifier using Tetrode technology with various operating scenarios, dissipation limit, safety system and challenges faced during high power operation at Indian test facility and describes the final outcome of R&D activity. C. The European 1 MW, 170 GHz industrial prototype CW gyrotron for ECRH&CD on ITER is a conventional (hollow-cavity) gyrotron, which is being developed by the European GYrotron Consortium (EGYC) in cooperation with the industrial partner Thales Electron Devices (TED), under the coordination of the European Joint Undertaking for ITER and the Development of Fusion Energy (F4E). The CW industrial prototype was extensively tested in the short-pulse regime (with pulse length up to 10 ms) and operated under long-pulse conditions with pulse lengths of up to 180 s, which is the limit at the High-Voltage (HV) power supply currently available at KIT. In this contribution we report on the performance of the tube during the long-pulse operation at the KIT test facility, details regarding the operating points are presented and the long-pulse phase of the experiments with pulses up to 180 s is analyzed.

Speaker: Dr Yasuhisa Oda (National Institute for Quantum and Radiological Science and Technology)

IAEA_FEC_2018_1-2Rabc_r2.pdf

53 Outcome of R&D program for ITER ICRF Power Source System

As a part of in-kind contribution, India is responsible to deliver nine numbers (1 Prototype + 8 series production) of RF Sources to ITER system, each having power handling capability of 2.5 MW/CW at VSWR 2:1 in the frequency range 35 – 65 MHz or 3.0 MW/CW at VSWR 1.5:1 in the frequency range 40 – 55 MHz, along with other stringent requirements. As there is no such amplifier chain able to meet the output power specifications as per ITER need, the RF source consists of two parallel three-stage amplifier chains, with a combiner circuit on the output side. This kind of RF source is unique in terms of its stringent specifications. A voluntary R&D program by India has been initiated for establishing the high power technology prior to Prototype and series production, using Diacrode and Tetrode tubes. In this program, single chain experimentation at 1.5MW for 2000s is conducted for the frequency range 35-65 MHz up to VSWR 2:1, with any phase of reflection coefficient. The main objective for the R&D test is to confirm the system performance for the power, duration and frequency range as per ITER need and to check the reliability of both the tube and the amplifier with matched as well as with mismatched load (up to VSWR 2:1), which essentially simulates the plasma load condition. To support the R&D program, a dedicated high power test facility has been developed at ITER-India to test RF amplifiers based on both the technologies. For Diacrode based system, high power ITER relevant tests completed in 2016 and reported elsewhere [1]. Over the past two years, assembly and integration of R&D RF source using Tetrode technology at Indian test facility is completed with validation of all the relevant sub-systems/systems as standalone mode. The high power RF test using Tetrode based RF amplifier achieved 1.7MW of power for 3600s duration at 36 MHz. For other ITER operating frequencies, the system was operated at 1.5MW/2000s successfully. This paper reports commissioning of RF amplifier using Tetrode technology with various operating scenarios, dissipation limit, safety system and challenges faced during high power operation at Indian test facility and describes the final outcome of R&D activity. [1] Aparajita Mukherjee et. al., Progress in High Power Test of R&D Source for ITER ICRF system, 26th IAEA FEC 2016, 17-22 Oct 2016, Kyoto, Japan

Speaker: Dr Yasuhisa Oda (Japan Atomic Energy Agency)

outcome of R&D Tetrode ICRH RF source-FIP-1-Rb_summary .pptx

54 Recent progress in the development of the European 1 MW, 170 GHz CW gyrotron for ITER

The European 1 MW, 170 GHz industrial prototype CW gyrotron for ECRH&CD on ITER is a conventional (hollow-cavity) gyrotron, which is being developed by the European GYrotron Consortium (EGYC) in cooperation with the industrial partner Thales Electron Devices (TED), under the coordination of the European Joint Undertaking for ITER and the Development of Fusion Energy (F4E). The CW industrial prototype was extensively tested in the short-pulse regime (with pulse length up to 10 ms) and operated under long-pulse conditions with pulse lengths of up to 180 s, which is the limit at the High-Voltage (HV) power supply currently available at KIT. In this contribution we report on the performance of the tube during the long-pulse operation at the KIT test facility, details regarding the operating points are presented and the long-pulse phase of the experiments with pulses up to 180 s is analyzed.

Speaker: Dr Yasuhisa Oda (Japan Atomic Energy Agency)

55 Technologies for realization of Large size RF sources for –ve neutral beam systems for ITER -Challenges, experience and path ahead & Progress in the ITER Neutral Beam Test Facility & Demonstration of 1 MV vacuum insulation for the vacuum insulated beam source in the ITER NB system

A. Technologies for manufacturing of small and medium size Ion source (upto four RF driver) for positive and negative neutral beam systems have been evolved over last many decades and such ion sources are being successfully operated at various experimental facilities across the world. However, as the need arises for the larger size ion sources (eight driver) for ITER diagnostics and heating neutral beam systems, several existing manufacturing technologies and considerations have to upgraded and re-evaluated to qualify them for (1) highest vacuum quality class (2) nuclear environment.
Diagnostic Neutral Beam (DNB) source is the first candidate in a family of such big size ion sources, being manufactured according to the ITER specification with ‘re-evaluated’ manufacturing technologies and it throws light on many unforeseen challenges as manufacturing progresses. The nature of challenges are mainly related to usage of the material with radioprotection requirement (i.e restricted contents of Co wt%0.05, Nb wt %0.01 and Ta wt %0.01), special requirements on weld joint configuration to enable full penetration with 100% volumetric inspectability, dissimilar material welding technologies, machining process development to meet stringent dimensional accuracies (in the range of 10-50 microns) of individual ‘angled’ grid segment to achieve overall alignment of +/-0.2mm, electro-deposition of copper with thickness>3mm over the angled surfaces with control over distortion, vacuum brazing, restricted usage of Silver for brazing and plating purpose, development of electrical isolators with customized electrostatic shield, threaded connection between metal and alumina load carrying capacity of 10kN with electrical isolation of 140kV in vacuum.
The paper shall present experience gathered in development of above mentioned manufacturing technologies, the methodology adopted for mitigating the practical limitations, prototyping to establish and qualify the manufacturing procedure, evaluating the non-conformities, assessment of deviation proposals, in compliance with ITER specifications. In summary, the experience generated during the manufacturing of DNB Beam source, presented here, is aimed to help in generating the recipe manufacturing and providing the ‘re-evaluated’ technical specifications for upcoming ITER neutral beam sources.

B. The ITER Heating Neutral Beam (HNB) injectors, one of the tools necessary both to achieve burning conditions and to control plasma instabilities, are characterized by such demanding parameters as to require the construction of a test facility dedicated to their development and optimization. This facility, called NBTF, is in an advanced state of realization in Padua (Italy), with the direct contribution of the Italian government, through the Consorzio RFX as the host entity, IO, the in kind contributions of three DA’s (F4E, JADA, INDA) and the technical and scientific support of various European laboratories and universities. The NBTF hosts two experiments: SPIDER and MITICA. The former is devoted to the optimization of the HNB and DNB ion sources and to the achievement of the required source performances. It is based on the RF negative Ion Source concept developed at IPP (Garching). MITICA is the full size prototype of the ITER HNB, with an ion source identical to the one used in SPIDER. The construction and installation of SPIDER plant systems was successfully completed with their integration into the facility, followed by integrated commissioning with control (CODAS), protection and safety systems. The mechanical components of the ion source have been installed inside the vessel and connected to the plants. Finally, the integrated commissioning of the whole system ended positively and the first experimental phase began. Also the realization of the MITICA project is well advanced, although the completion of the system and its entry into operation is expected in 2022 due to the long procurement times of the in-vessel mechanical components. In particular, the power supply designed to operate at 1MV are in an advanced phase of realization, all the high voltage components have been installed and the complex insulation test phase has begun in 2018. Furthermore, all the other auxiliary plant systems are being installed and / or undergoing testing. This paper gives an overview of the progress of the NBTF realization with particular emphasis on issues discovered during this phase of activities and to the adopted solutions in order to minimize the impact on the schedule while maintaining the goals of the facilities. Finally, the first results obtained with SPIDER experimentation and with the 1MV insulation tests on the MITICA HV components will be presented.

C. For the ITER neutral beam (NB) system, a measure to achieve the 1 MV vacuum insulation of the beam source have been developed. For this purpose, design basis for 1 MV vacuum insulation has been developed by integrating previous empirical scaling for plane and coaxial electrodes and new scaling for area with locally-concentrated electric field. Consequently, as the measure, the beam source is surrounded by more than three intermediate electrostatic shields instead of single gap to sustain 1 MV. Effectiveness of the shields designed by the design basis was experimentally verified by using a part of the beam source. The voltage holding capability has been significantly improved from 0.7 MV to 1 MV. This result ensures the 1 MV vacuum insulated beam source in the ITER NB system.

Speaker: Mr Jaydeepkumar Joshi (ITER-India (Institute for Plasma Research))

FIP1-3Ra(J.Joshi)_FIP1-3Rb(V.Toigo)_FIP1-3Rc(A.Kojima).pdf

56 Progress in the ITER Neutral Beam Test Facility

The ITER Heating Neutral Beam (HNB) injectors, one of the tools necessary both to achieve burning conditions and to control plasma instabilities, are characterized by such demanding parameters as to require the construction of a test facility dedicated to their development and optimization. This facility, called NBTF, is in an advanced state of realization in Padua (Italy), with the direct contribution of the Italian government, through the Consorzio RFX as the host entity, IO, the in kind contributions of three DA’s (F4E, JADA, INDA) and the technical and scientific support of various European laboratories and universities. The NBTF hosts two experiments: SPIDER and MITICA. The former is devoted to the optimization of the HNB and DNB ion sources and to the achievement of the required source performances. It is based on the RF negative Ion Source concept developed at IPP (Garching). MITICA is the full size prototype of the ITER HNB, with an ion source identical to the one used in SPIDER. The construction and installation of SPIDER plant systems was successfully completed with their integration into the facility, followed by integrated commissioning with control (CODAS), protection and safety systems. The mechanical components of the ion source have been installed inside the vessel and connected to the plants. Finally, the integrated commissioning of the whole system ended positively and the first experimental phase began. Also the realization of the MITICA project is well advanced, although the completion of the system and its entry into operation is expected in 2022 due to the long procurement times of the in-vessel mechanical components. In particular, the power supply designed to operate at 1MV are in an advanced phase of realization, all the high voltage components have been installed and the complex insulation test phase has begun in 2018. Furthermore, all the other auxiliary plant systems are being installed and / or undergoing testing. This paper gives an overview of the progress of the NBTF realization with particular emphasis on issues discovered during this phase of activities and to the adopted solutions in order to minimize the impact on the schedule while maintaining the goals of the facilities. Finally, the first results obtained with SPIDER experimentation and with the 1MV insulation tests on the MITICA HV components will be presented.

Speaker: Mr Jaydeepkumar Joshi (ITER-India (Institute for Plasma Research))

FIP1-3Rb_V.Toigo_SingleSlide.pptx

57 Demonstration of 1 MV vacuum insulation for the vacuum insulated beam source in the ITER NB system

For the ITER neutral beam (NB) system, a measure to achieve the 1 MV vacuum insulation of the beam source have been developed. For this purpose, design basis for 1 MV vacuum insulation has been developed by integrating previous empirical scaling for plane and coaxial electrodes and new scaling for area with locally-concentrated electric field. Consequently, as the measure, the beam source is surrounded by more than three intermediate electrostatic shields instead of single gap to sustain 1 MV. Effectiveness of the shields designed by the design basis was experimentally verified by using a part of the beam source. The voltage holding capability has been significantly improved from 0.7 MV to 1 MV. This result ensures the 1 MV vacuum insulated beam source in the ITER NB system.

Speaker: Mr Jaydeepkumar Joshi (ITER-India (Institute for Plasma Research))

58 Diagnostic mirrors for ITER: research in a frame of International Tokamak Physics Activity

Mirrors will be used as first plasma-viewing elements in optical and laser-based diagnostics in ITER. Deterioration of the mirror performance due to e.g. sputtering of the mirror surface by plasma particles or deposition of plasma impurities will hamper the entire performance of the affected diagnostic. Specialists Working Group on First Mirrors (FM SWG) in the Topical Group on Diagnostics of the International Tokamak Physics Activity (ITPA) plays a crucial role in finding solutions for diagnostic first mirrors. Sound progress was achieved during the past decade. Single crystal (SC) rhodium (Rh) mirrors became available. SC Rh and molybdenum (Mo) mirrors survived in conditions corresponding to ~ 200 cleaning cycles without a degradation of reflectivity. These results are important for a mirror cleaning system, based on sputtering of contaminants by plasma. Efforts are invested to the physics understanding of a cleaning discharge. Ion energy distribution and flux in radiofrequency (RF) discharge have been studied. Repetitive cleaning was tested on several mirror materials. Experiments comprised contamination/cleaning cycles. The reflectivity SC Mo mirrors was preserved after 34 cycles. First in-situ cleaning was conducted in EAST with a mock-up mirror of ITER Edge Thomson Scattering using RF plasma. Contaminants from the mock-up mirror were removed. Mirror contamination can also be suppressed by a protecting diagnostic duct. A Deposition Mitigation duct system was exposed in KSTAR. The real-time measurement of deposition in the diagnostic duct was pioneered during this experiment. Results evidenced the dominating effect of the wall conditioning and baking on contamination inside the duct. A baffled cassette with mirrors was exposed in the main wall of JET ILW for 23,6 plasma hours. No significant degradation of reflectivity was measured on mirrors in the ducts. Predictive modeling was advanced. A model for the particle transport, deposition and erosion inside the port-plug was used in selecting an optical layout of the ITER core Charge-Exchange Recombination Spectroscopy diagnostic. These achievements contributed to the focusing of the first mirror research, accelerating the diagnostic development. Predictive modeling requires more efforts to be invested. Ensuring the progress in the remaining crucial areas will be a focus of the future work of the FM SWG

Speaker: Dr Andrey Litnovsky (Forschungszentrum Juelich, Germany)

AL IAEA FEC 2018 Mirrors Talk final.pdf

AL IAEA FEC 2018 Mirrors Talk final.pptx

59 Integration of Thomson scattering and laser-induced fluorescence in ITER divertor: engineering and performance analysis

This paper describes the benefits and challenges of divertor Thomson scattering 55.C4 (DTS) and laser-induced fluorescence 55.EA (LIF) integration in the divertor port #8 of ITER. One of the main challenges for the DTS system is to measure extremely low electron temperatures in the vicinity of the divertor plates. The cool and dense divertor plasma leads to pronounced collective effects and significant distortions of the TS spectra. Therefore, standard TS signal processing, valid for light scattering on a swarm of free electrons, is already not valid. To examine the real DTS performance, we apply a special simulation technique based on synthetic experiments. The estimated measurement accuracies of electron temperature and density are quite better than the specified technical requirements, in spite of the pronounced collective effects. On the contrary, in the case of low electron density, when the classical TS spectrum is expected, the diagnostics performance degrades significantly, though still satisfying the technical requirements. Currently, the LIF diagnostic is to measure density of Helium atoms with a collisional-radiative model (CRM) describing a relation between the fluorescence and plasma parameters. Required for CRM electron parameters are taken from DTS diagnostics. The temporal forms of the Helium fluorescence are dependent on electron parameters and the pumping laser pulse characteristics. Therefore, LIF can measure electron density in the range of 10^18 10^20 m^-3 analyzing the temporal behavior of Hellium fluorescence with the Helium CRM. This technique helps to expand the measurable range of electron density. The main advantage of this LIF measurements is that calibration of the collection system spectral and / or absolute sensitivity is not required, contrary to the DTS approach. Both DTS and LIF are laser aided diagnostics; hence, it seems attractive to develop universal laser and probing optics, which is the most sophisticated and expensive part of any ITER optical diagnostics. The engineering solutions discussed and challenges of the DTS and LIF integration includes collinear combination of DTS and LIF lasers, laser mirrors, collection mirrors, etc. Although the proposed solutions are considered in terms of ITER divertor compatibility, their use in currently operating magnetic confinement devices is also under discussion.

Speaker: Dr Eugene Mukhin (Ioffe Institute)

FEC 2018 E Mukhin DTS LIF INTEGRATION FIP 1-5 _.pdf

FEC 2018 Mukhin poster 2018-10-19.pdf

FIP 1-5 E Mukhin DTS LIF INTEGRATION.pdf

60 Current Design and R&D Progress of CN HCCB TBS

As the testing mockup of tritium breeding blanket for DEMO, Chinese Helium Coolant Ceramic Breeder (HCCB) Test Blanket System (TBS) are under developing by China and will be tested in ITER to verify the key tritium breeding blanket technologies. After the approval of conceptual design by ITER Organization in 2015, the design optimization and more R&D activities for HCCB TBS have been under implementation for preliminary design phase. As the structural material of TBM module, eight tons RAFM steel (CLF-1) plates and forgings have been fabricated and a certification of 3.2 requested by EU Pressure Equipment Directive 97/23/EC (PED) has been obtained for CLF-1 steel. The fabrication techniques for the functional materials, beryllium pebble and Li4SiO4 pebble, have also been developed and the properties have tested. The new manufacture facility for Li4SiO4 pebble is under construction and the manufacture facility for beryllium pebble was upgraded to achieve production rate 10kg/batch. Recently the TBM-set design was significantly optimized and the whole integration method of TBM and the fabrication procedure plan has been updated. The results show that the total heat deposition in TBM was similar with conceptual design, while the tritium production ratio was slightly higher. The fabrication technology of TBM is under development. Following the fabrication procedure plan of TBM, semi-prototype of TBM is under fabrication to verify the final integration plan. Ancillary systems have been optimized considering the review comments, safety and interface requirements. Accordingly the Process Flow Diagram (PFD) and Pipe & Instrumentation Diagram (PID) have been updated, but still some interface issues with ITER facility have been identified and have to be solved. The system performance has been assessed to optimize the operation control plan and equipment requirements. Several test platforms for breeding blanket technology development have been constructed and started experiments to test components, processes and get the operation data. At same time, the safety assessment of HCCB-TBS has been updated and it shows that HCCB TBS has not over-temperature issues for all accident cases. Considering the limited inventories and multiple confinement barriers, no major safety consequences had been identified through accident assessments.

Speaker: Prof. Xiaoyu WANG (Southwestern Institute of Physics)

27th IAEA FEC FIP-1-6 - WANG Xiaoyu v0.4.pdf

Reception

Tuesday, 23 October

FIP/1 P1 Posters

61 Completion of 1st ITER gyrotron manufacturing and 1 MW test result

Speaker: Dr Yasuhisa Oda (Japan Atomic Energy Agency)

1PageSummary.pdf

62 Completion of the first TF Coil Structure of ITER

Speaker: Dr Masataka Nakahira (National Institutes for Quantum and Radiological Science and Technology)

Poster Poster_CN258_FIP1-1_Completion1stTFCS_ITER_r1.pdf

Summary Slide CN258_FIP1-1_Completion1stTFCS_ITER_SummarySlide_r0.pdf

63 Current Design and R&D Progress of CN HCCB TBS

Speaker: Prof. Xiaoyu WANG (Southwestern Institute of Physics)

64 Demonstration of 1 MV vacuum insulation for the vacuum insulated beam source in the ITER NB system

Speaker: Mr Atsushi Kojima (National Institutes for Quantum and Radiological Science and Technology)

FIP1-3Rc_A.Kojima_Summary_r0-MK.pptx

65 Diagnostic mirrors for ITER: research in a frame of International Tokamak Physics Activity

Speaker: Dr Andrey Litnovsky (Forschungszentrum Juelich, Germany)

66 Integration of Thomson scattering and laser-induced fluorescence in ITER divertor: engineering and performance analysis

Speaker: Dr Eugene Mukhin (Ioffe Institute)

67 Outcome of R&D program for ITER ICRF Power Source System

Speaker: Mr Rajeshkumar Gajanan Trivedi (ITER-India, Institute for Plasma Research)

outcome of R&D Tetrode ICRH RF source-FIP-1-Rb_summary .pptx

68 Progress in the ITER Neutral Beam Test Facility

Speaker: Dr Vanni Toigo (Consorzio RFX)

FIP1-3Rb_V.Toigo_SingleSlide.pptx

69 Recent progress in the development of the European 1 MW, 170 GHz CW gyrotron for ITER

Speaker: Dr Gerd Gantenbein (Karlsruhe Institute of Technology, Institute for Pulsed Power and Microwave Technology)

70 Technologies for realization of Large size RF sources for –ve neutral beam systems for ITER -Challenges, experience and path ahead

Speaker: Mr Jaydeepkumar Joshi (ITER-India (Institute for Plasma Research))

FIP1-3Ra(J.Joshi)_FIP1-3Rb(V.Toigo)_FIP1-3Rc(A.Kojima).pdf

Summary Slide_V2_J. Joshi.pptx

OV/3 Overview Magnetic Fusion

71 Progress of JT-60SA Project

The JT-60SA project was initiated in June 2007 under the framework of the Broader Approach (BA) agreement and Japanese national fusion programme for an early realization of fusion energy by conducting supportive and complementary work for the ITER project towards supporting the basis for DEMO. In 2009, after a complex start-up phase due to the necessity to carry out a re-baselining effort to fit in the original budget while aiming to retain the machine mission, performance, and experimental flexibility, the detailed design of the project could start immediately followed by the start of manufacturing of the long lead items. Components and systems of JT-60SA are procured by the implementing agencies (IAs): Fusion for Energy in EU and QST (previously JAEA) in Japan. With the project now in an advanced implementation stage, the early defined approach for its implementation has proven to be successful and hence continues to be employed. This is underpinned by the very close collaboration between QST in Japan, F4E in Europe, and all other European stakeholders: the EU Voluntary Contributors (EU-VCs) and EUROfusion. The employed management model follows the early establishment of a single Integrated Project Team (IPT) that operates in accordance to an agreed Common Quality Management System, defining resources and processes crossing the lines between organizations. For JT-60SA the same management model strategy is planned also for the period beyond 2020, that is when the facility will be jointly operated and enhanced by the EU and JA.The paper will overview the progress of the manufacturing and assembly of the JT-60SA machine, the outlook towards First Plasma, and progress in preparing for the scientific exploitation of JT-60SA following this milestone.

Speaker: pietro barabaschi (f4e)

IAEA_2018_Barabaschi 16x9.pptx

IAEA_2018_Barabaschi SUMMARY SLIDE.pptx

72 Progress of the CFETR Design

The Chinese Fusion Engineering Test Reactor (CFETR), complementing ITER, is aiming to demonstrate fusion energy production up to 200 MW initially and to eventually reach DEMO relevant power level, to manifest high duty factor of 0.3~0.5, and to pursuit tritium self-sufficiency with tritium breeding ratio (TBR) > 1. The key challenge to meet the missions of the CFETR is to run the machine in steady state and high duty factor. Recently, a self-consistent steady-state scenario for CFETR with fully sustained non-inductive current drive is developed using a multi-dimensional code suite with physics-based models. In addition, results from the experimental validation conducted by a recent EAST steady-state experiment with off-axis current drive enhance confidence in the performance prediction from the integrated modeling. Finally, a fully non-inductive reverse-shear scenario scaled to R = 6.7 m, βN~3, H98 ~ 1.5 and fBS ~ 0.75 with the performance that meets the high gain CFETR mission is demonstrated. The scenario presents a self-consistent solution for the CFETR transport, equilibrium and pedestal dynamics.
At present, the CFETR physics design focuses on optimization of the third evolution CFETR (R = 7 m, a = 2 m, kappa = 2, Bt = 6.5-7 T, Ip = 13 MA) consistent with steady-state or hybrid mode and a radiative divertor. Listed below are the main tasks we needed to tackle in the near-term, e.g. to demonstrate compatibility with the alpha particle stability and transport, and to quantify the tritium burn-up rate during the steady-state burning plasma phase in order to find a solution to meet the central fueling requirement, and so on. The details will be given in this meeting

Speaker: Guoqiang Li (Institute of Plasma Physica, CAS)

IAEA_FEC_OV_I3-2_V12_20181022_for talk.pdf

73 Overview of the Validation Activities of IFMIF/EVEDA: LIPAc, the Linear IFMIF Prototype Accelerator and LiFus6, the Lithium Corrosion Induced Facility

In this report, the latest results of the validation activities of the IFMIF/EVEDA project under the Broader Approach agreement are overviewed. For the Linear IFMIF Prototype Accelerator (LIPAc) to demonstrate the 9MeV/125mA D+ beam acceleration, the beam qualification study of the injector was completed with the emittance of 0.16 pi mm mrad smaller than required 0.3 pi mm mrad, and the maximum vane voltage in the RFQ cavity was achieved at 143kV exceeding the required 132kV. These components and other subsystems of LIPAc are ready to inject the beam to RFQ to provide the 5MeV D+ beam. The Superconducting RF linac necessary for the 9MeV D+ beam is close to the end of manufacturing phase to start its final assembly in Rokkasho. For the liquid lithium loop activities, 4,000 hours lithium corrosion test of the Reduced Activation Ferritic/Martensitic steels using the LiFus6 were completed and verified that the corrosion rate can be kept under control and well below the requirement of 1 micro-m/y, after achieving a good purity of lithium, < 30ppm N.

Speaker: Masayoshi Sugimoto (QST-Rokkasho)

FEC2018_OV-3-3_summary_Overview_the_validation_activities_of_IFMIF-EVEDA_Sugimoto.pdf

FEC2018_OV3-3_talk_Overview_the_validation_activities_IFMIF-EVEDA_Sugimoto.pdf

74 The Strategy of Fusion DEMO In-vessel Structural Material Development

The structural material development for the breeding blanket in a future fusion reactor is regarded as the most challenging technical issue due to the significance of 14 MeV DT fusion neutron irradiation that induces high displacement damage with a significant amount of the transmutation formed gas elements such as helium and hydrogen. The strategy of fusion in-vessel structural material development toward fusion DEMO is addressed with special emphasis on the current status and the limitations due to the reliability of data. A major issue in developing and validating structural materials for a fusion DEMO reactor are missing facilities where materials can be tested under the real in-vessel conditions of deuterium-tritium (DT) fusion. Ideally, neutron irradiation induced changes are expected to be negligible or “minor”. The reality is, however, that irradiation effects are neither “negligible” nor “minor”. Thus, it is essential to define the negligible and maximum level of irradiation-induced changes which could be incorporated into safety factors that are defined “empirically”, and the most significant technical challenges are to develop and qualify materials based on the knowledge and data acquired in experiments not performed under “real” fusion environment but in fission neutron irradiation and various simulation irradiation experiments, and to develop and verify a framework of DEMO reactor design criteria for in-vessel components (DDC-IC). Here we propose a new strategy based on probabilistic approaches, where the probability of failure is calculated based on the probability density function of postulated load distribution and material property distribution, as a part of the design methodology in order to mitigate the uncertainties caused by multiple sources. It is essential to conduct statistical analyses on material property data to make the data applicable to the probability based design method. Consequently, the vast amount of fission neutron irradiation data which fulfill the statistical requirements should be developed up to some critical irradiation dose levels at which the irradiation effects caused by fusion neutron spectra are expected to become very different from fission data.

Speaker: Dr Hiroyasu Tanigawa (National Institutes for Quantum and Radiological Science and Technology)

Presentation_CN-258_FEC2018_OV3-4_Tanigawa_fb.pptx

Presentation_CN-258_FEC2018_OV3-4_Tanigawa.pdf

Summary Slide Summary Slide_CN-258_FEC2018_OV3-4_Tanigawa_rev2 .pptx

P1 Posters

75 ACTYS Code System: Towards Next Generation Nuclear Activation Codes for Fusion Reactors

Nuclear activation and subsequent radiological response of structural materials within fusion reactors like ITER and beyond need to be studied for operational, safety and radiological waste management reasons. The future fusion machines should be equipped with low radioactive materials optimized for expected neutron environment. Numerical tools with extended capabilities are needed for this kind of analysis. A project named ACTYS-Project is initiated at Institute for Plasma Research to meet the requirements stated above. This effort so far developed more than five states of art codes and few innovative computational tools for analysis and design of fusion reactors. The details of all the codes and tools will be presented in this paper. ACTYS is the first code within the project. It is a single-point neutron activation code and computes nuclide inventories and other radiological responses within materials when exposed to neutron flux through either continuous, pulse irradiation or mixed. It solves coupled first-order LODEs using Bateman solution for linearized chains. An ‘exponential convergence’ algorithm and ‘chain weighing’ termination technique is developed in-situ for this purpose. These two methods lend ACTYS an added edge over typical linear chain solvers. ACTYS is well validated and the details of the same will be presented. Highly resolved nuclear activation analysis and radiation waste classification are warranted for large-sized fusion machines with a wide variety of materials. To ensure a fast multi-point activation analysis without sacrificing accuracy, inherent changes must be done to single-point activation codes like ACTYS. To this end, a multipoint activation code-named ACTYS-1-GO is developed. Recently, it has been coupled with transport code ATTILA by developing a subsidiary module, activation source generator. One of the important features is that nearly 1 million meshes can be computed in less than few hours. A mathematical formulation to account for the contribution of the parent constituents of any irradiated material towards the radiological responses was derived and implemented. The first order derivatives of Bateman linear chain solution with respect to the decay and cross sections constants are generally used for the sensitivity analysis. A simplified and improved set of recursive relations are developed for these derivates.

Speaker: Dr Subhash P.V (ITER-India, Institute for Plasma Research, Gandhinagar, Gujarat)

ACTYS_slide.pdf

ACTYS_slide.pdf

76 Alignment and Calibration Schemes for ITER CXRS-Pedestal Diagnostic

Charge eXchange Recombination Spectroscopy (CXRS) diagnostic shall provide the key measurement for ITER advance plasma control and physics studies. ITER CXRS-pedestal has a primary role of edge ion temperature, plasma rotation (toroidal and poloidal velocity) and impurity density measurements in the pedestal region (r/a=0.85 -1.0). Meeting the measurement requirements for these parameters in ITER is more challenging than the present tokamaks due to restricted access for diagnostics components in addition to the harsh environment of ITER. Some of these challenges are like the calibration offset that limits the velocity measurement accuracy requirement. As well as precise alignment required because of the lower angle between the line of sight with a toroidal plane that introduces additional error in the measurement. Therefore, to meet the measurement requirements in ITER, robust calibration and alignment schemes are being developed. CXRS-pedestal shall cover broad wavelength range, the emission of (He, Be, Ne, Ar, C) recombining lines (460-532nm) and Beam Emission Spectroscopy (BES) Hα (656.3nm) spectral line simultaneously, compatible with the spatial resolution of 20 mm (that demands a fine alignment) with 5Hz DNB modulation: 100ms exposure with DNB ON, 100ms background exposure. Statistical and systematic errors including atomic modeling along with low light signal due to strong attenuation of the diagnostic neutral beams require better light transmission path and high throughput spectrometer detection system. To access this requirement, preliminary performance assessment carried out using Simulation of Spectra (SOS) code to see the dependency of the measurement accuracy on SNR. In this contribution, details of the design and development of the ITER CXRS-pedestal diagnostic system in view of alignment & calibration in the suitable transmission system, this includes the optimum light transmission path analysis using ZEMAX ray tracing tool. This will ensure the required alignment for accurate measurement from the DNB and plasma cross-section area of the pedestal region. The various calibration and alignment schemes are studied and shall be developed to test the performance in the ITER-India Lab to meet the ITER requirement.

Speaker: Mr Gheesa Lal Vyas (ITER-India, Institute for Plasma Research)

Summary slide_FIP_P1_33.pdf

77 Application of Finite Element Techniques in Simulation of Mechanical Design and Performance Assessment of Different Components of a Neutral Beam Systems

Accelerators, Ion dumps and beam transport system for Neutral Beam application are designed to manage high heat loads in the range of 2-10MW/m2. The performance of these components under various damage criteria are assessed for their thermo-mechanical stability under various operating and faulty conditions. Due to the pulse nature (3s ON/ 20s OFF with 5 Hz modulation) of beam operation, components often exposed to cyclic thermal loads. Further, the above system is incorporated with large number of flexible elements (e.g. bellows, etc.) to absorb the thermal movements. For systems like accelerator and electrostatic residual ion dumps, there is an additional need of non-metallic components, like ceramics, which functions as electrical isolation as well act as structural elements. To assess diverse nature of such systems with complex loading requirements, Finite Element Analysis tools (e.g. ANSYS, CFX, SYSWELD, etc.) have been employed as part of design evolution and results are verified according to codes and standards (ASME / RCC-MR / EJMA). The experimental validation of effectiveness of these assessment have been also performed by prototype testing and performing the tests on the real manufactured products. It is also important to note that, the tools are also useful to address the in-process manufacturing modification those may arise due to feasibility constraints. The paper shall present some of the important simulations results on 10MW/m2 capability of Heat Transfer elements, functional tests on 100 kV post insulators, bellows assessment in water lines, CFD simulations for beam source components, etc.

Speaker: Mr VENKATA NAGARAJU MUVVALA (ITER-India, Institute for Plasma Research)

78 Automated Testing of ITER Diagnostics Scientific Instrumentation

ITER requires extensive diagnostics to meet the demands for machine operation, plasma control, protection, safety and physics studies. Most diagnostics require high performance scientific computing for the processing of complex algorithms for the measurements. The most stringent requirements are found in the more than 50 diagnostics measurement systems in terms of high performance data acquisition, data processing and real-time data streaming from distributed sources to the plasma control system as well as large amounts of raw data streaming to scientific archiving. While most of these requirements have been achieved individually the challenge for ITER will be the integration of these state-of-the-art technologies in a coherent design while maintaining all of the performance aspects simultaneously. The instrumentation and control (I&C) systems for each diagnostic must meet around 500–700 functional and non-functional requirements which include also the requirements from the ITER handbooks such as the Plant Control Design Handbook (PCDH), Electrical Engineering Design Handbook (EDH) and the Radiation Compatibility Handbook. While the diagnostics I&C system engineering methodology (Figure 1) is well established for requirements management, detailed design, and implementation, the acceptance testing, demonstrating the compliance of the I&C system with the requirements needs further elaboration. This includes the definition of the test scenarios, detailed test procedures, and well-defined pass-fail criteria for each test. Since compliance validation against a large number of requirements can be very time consuming a high degree of automation during testing is desirable. This paper presents the elaboration of the pass/fail criteria, the acceptance testing procedures for diagnostics plant system I&C, and describes the design and implementation for automated testing. First results will illustrate the reduction in testing time for obtaining a detailed compliance evaluation.

Speaker: Dr Stefan Simrock (ITER)

Automated_Testing_ITER_Diagnostics_update.pdf

summary_slide_automated_testing.pptx

79 Baking System of Aditya Upgrade Tokamak

In tokamaks, baking of vacuum vessel and first wall components is a prerequisite in order to obtain impurity free plasmas. Baking is performed to remove impurities viz. H2, H2O and Hydro-Carbon from the vessel and first wall components. ADITYA tokamak has been upgraded ADITYA-U tokamak to achieve shaped plasmas. The ADITYA-U is equipped with a comprehensive baking system for heating the SS vacuum vessel, pumping systems, associated diagnostics along with the graphite limiter and diverter tiles up to 150 C. The DC Glow discharge cleaning is also carried out in presence of baking to achieve better wall conditioning for high performance plasma operation. Due to space limitation between vessel and Toroidal field coils at the high-field side, 1.5 mm thick silicon heaters has been designed and procured. In-situ installation of heaters has been quite challenging due to structural complexity. For efficient heat insulation, 6 mm thick silicon jacket designed, fabricated and installed according to vessel profile. A detail analysis carried out in ANSYS for its optimum performance and to examine its effect on vessel, especially on the several weld joints. Whole baking system consists of ~80 heaters installed on different sectors of the vessel, pumps and diagnostics. The heaters are controlled in close loop by in-house developed Programmable Logic Controller (PLC) based automatic control system. It comprises of three main phases, temperature ramp-up, constant heating and ramp-down to room temperature. All these phases are individually controlled as required. The entire baking system has been tested thoroughly for its automatic operations for long hours(~48 hr.), integration, ruggedness, reliability, small form factor. The detailed hardware concept, software design and prototype testing and its regular operation in presence and absence of GDC will be discussed. Partial pressure of impurities is monitored in every baking cycle which decides the controls of the baking temperature and duration automatically. Further, the potency of lithiumization carried out before, during and after baking has been compared for the first time in ADITYA-U by estimating the lithium lifetime on the walls with plasma operation. The improved wall conditioning with baking and its effect on plasma operation along with technical challenges faced during installation will be presented in this paper.

Speaker: Mr Kaushal Patel (Institute for Plasma Research)

Summary - Baking of Aditya Upgrade tokamak.pptx

80 Basic studies of the interaction of blobs with suprathermal ions and millimetre-wave beams in the TORPEX device

The fundamental interactions between turbulent structures or blobs and suprathermal ions, injected by Li6+ beams in plasmas created by microwaves at 2.45GHz with ne~1015-1017m-3 and Te~2-10eV, are extensively investigated on the TORPEX toroidal device. Comparisons between fully validated numerical simulations and experimental 3D time-averaged suprathermal ion profiles reveal an entire spectrum of non-diffusive suprathermal ion transport: super-diffusive, diffusive, or sub diffusive, depending on particle energy and turbulence amplitude. 3D time-resolved measurements of 30eV and 70eV ions, exhibiting super- and sub-diffusive transport respectively, show that in all cases the ions are subject to bursty displacement events and that intermittency, quantified by the skewness of the time-traces, is present to some degree in all profiles, also for intermediate energies, including in the sub-diffusive cases. We develop an analytical model that links the time averaged-profile of the ion current and the profile of the statistical moments of the fluctuations. In fusion devices, externally injected beams in the electron cyclotron (EC) frequency range are employed for heating and current drive, and to stabilize neoclassical tearing modes. EC beams must propagate through the Scrape-Off Layer where blobs may scatter the incoming wave by locally modifying the plasma permittivity. This may lead to a loss of efficiency in EC heating and mode stabilization. To understand the effect of plasma turbulence and its structures on the propagation of millimeter waves (mmw), we measure wave scattering in TORPEX by blobs of size comparable to the wavelength. A low-power beam is launched at 29.7GHz in the X-mode from the top of the device using a pyramidal horn antenna. The X-mode component of the transmitted power is detected at the bottom using a pyramidal horn antenna and a Schottky diode, whose position can be radially adjusted. A conditional sampling technique averages the effect of several thousand individual blobs. Combining these scattering measurements with first principle full-wave simulations using COMSOL, we show that density fluctuations associated with plasma blobs, with δne as small as ~10-3 of the critical density, can significantly defocus the mmw-beam in the wake of the blobs, resulting in mmw-power fluctuations that increase monotonically with the blob amplitude.

Speaker: Dr Ivo Furno (EPFL- CRPP)

81 Comparative modeling of plasma boundary corrugation due to the application of 3-D fields with ELM control coils in various ITER scenarios

The plasma response to the 3-D external resonant magnetic perturbation (RMP) fields, applied for controlling type-I edge localized modes (ELMs) in ITER, is systematically computed in terms of the normal displacement of the plasma surface, in other words the 3-D corrugation of the plasma boundary. Five representative ITER H-mode plasma scenarios, ranging from an initial hydrogen plasma discharge in pre-nuclear phase to the Q = 10 nuclear phase DT operation. The plasma surface corrugation, computed using the MARS-F code, is used as a basis to understand the capability and robustness of the type-I ELM control in these ITER scenarios. A key aspect of this study is to assess effects of variation/uncertainty of pedestal plasma rotation on the plasma response. For each plasma scenario, a set of the toroidal rotation - both amplitude and radial profile - is generated by the transport code ASTRA, assuming different Prandtl numbers as well as different ratios of the toroidal momentum to thermal confinement times. Toroidal modeling results show that, (i) the plasma response is similar for the two DT scenarios with 15 MA/5.3T plasmas but with different fusion gain factors (Q=5 versus Q=10); (ii) the other plasma scenarios, with similar rotation profiles, have different plasma boundary corrugation; (iii) the effect on ELM control performance by utilizing 2 or 3 rows of coils, with the coil phasing optimization, varies depending on the availability of the ELM control coil power supplies. The plasma response database, generated in this study, can also be used for further studies such as the divertor footprint and heat load, or energetic particle losses due to RMP.

Speaker: Dr Li Li (Donghua University, Shanghai, China)

82 Completion of DC 1 MV power supply system for ITER neutral beam test facility

Technologies of DC 1 MV insulation with water and DC 1 MV vacuum insulation have been developed. As the result, manufacturing of DC 1 MV power supply components to produce 1 MeV negative ion beams have been completed for the ITER neutral beam test facility (NBTF). For the transmission line (TL), insulating tubes for hot and cooling water have been developed by clarifying resistivity of high-temperature water and properties of insulation material with water absorption. Based on these results, the integrated configuration of the TL has been established through electrical and thermo-mechanical analyses. For the HV bushing, 1 MV vacuum insulation was achieved based on the empirical scaling for the vacuum insulation. Then, all components have been manufactured and shipped to the NBTF site in 2017. The installation is on-going toward the integration test in 2018. These achievements contribute to push forward with a start of the NBTF operation and a realization of the ITER NB.

Speaker: Dr Hiroyuki Tobari (National Institute of Quantum and Radiological Science and Technology)

Summary-FIP_P1-10.pdf

83 Conceptual Design Study for Heat Exhaust Management in the ARC Fusion Pilot Plant

The ARC pilot plant conceptual design study [1] is extended to explore options for managing ~525 MW of fusion power generated in a compact high field ($B_0$ = 9.2 T) tokamak about the size of JET ($R_0$ = 3.3 m). Exploiting ARC’s demountable high temperature superconductor toroidal field (TF) magnets, poloidal magnetic field (PF) coils located inside the TF, and vacuum vessel (VV) immersed in molten salt FLiBe blanket, this follow-on study identifies novel robust power exhaust solutions. The superconducting PF coil set is reconfigured to create double-null plasma equilibria that include an X-point target divertor geometry. Modeling shows that such long-leg configurations enhance power handling and can achieve passively-stable detachment fronts that stay in the divertor leg over a wide power window [2,3]. The VV is modified to include the divertors while retaining original core plasma volume and TF magnet size. The molten salt FLiBe blanket shields all superconductors, functions as an efficient tritium breeder, and, with augmented forced flow loops, serves as a single-phase, low-pressure coolant for the divertor and VV. MCNP neutronics calculations show a tritium breeding ratio of ~1.08. The neutron damage rate of the remote divertor targets is ~3 times lower than that of the first wall, which is beneficial because high neutron damage often leads to degradation in thermal performance. The demountable TF magnets allow for vertical maintenance schemes and replacement every 1-2 years, increasing tolerance for neutron damage. The divertor has tungsten swirl-tube cooling channels capable of exhausting 12 MW/m$^2$ of heat flux, which includes a factor of ~8 safety margin over anticipated steady state heat loads. Novel diagnostics supporting the heat exhaust mission compatible with the neutron environment are proposed, including the use of Cherenkov radiation emitted in FLiBe to measure fusion reaction rate, microwave interferometry to measure divertor detachment front location, and IR imaging through the FLiBe blanket to monitor divertor “hotspots.” *The authors acknowledge support from the MIT Nuclear Science and Engineering Department and the PSFC.* [1] B.N. Sorbom, *et al.*, *Fus. Eng. and Des.* **100** (2015): 378-405. [2] M.V. Umansky, *et al.*, *Phys. of Plasmas* **24** (2017): 056112. [3] M. Wigram, *et al.*, *Conts. to Plasma Phys.* (2018)

Speaker: Ms Elizabeth Tolman (UsPSFC)

summary slide.pptx

84 Consorzio RFX Contribution to the JT-60SA Project in the Frame of the Broader Approach Agreement

The JT-60SA satellite tokamak is now under advanced assembly phase in Naka (Japan). The majority of the new power supplies are provided by Europe, and the Italian National Research Council (CNR), acting through Consorzio RFX, has contributed in particular with two systems: the Quench Protection Circuits (QPC) for the superconducting magnets and the Power Supply System for RWM control. The procurement of both the systems has been successfully carried out: the QPCs were delivered to Naka site in autumn 2014; the installation, commissioning and acceptance tests were completed in July 2015, fully in line with the schedule agreed in 2009. The protection system for the superconducting coils is composed of thirteen units: three for the TF circuit and ten for the PF circuits. Their duty is to conduct the coil current in normal operation and commutate it into a dump resistor in case of quench or other faults by means of a dc Circuit Breaker (CB). The nominal currents to be interrupted and the maximum reapplied voltages are 25.7 kA and 2.8 kV for the TF QPCs and ±20 kA and ±5 kV for PF QPCs. As for the RWM-PS system, we are very close to the completion too, with the delivery on site and closure of the procurement expected in autumn 2018. This system consists in an input rectifier stage and 18 power amplifiers, one for each coils, capable to supply a peak current of 300 A and an output voltage of 240V and satisfy strict dynamic requirements in terms of latency and current bandwidth (50 s, 3 kHz) thanks to the adoption of new hybrid Silicon-Silicon Carbide (Si-SiC) power semiconductors for the power amplifiers and to the development of a new sophisticated control board, based on the combination of a fast microcontroller and a FPGA running optimized firmware. A summary of the studies for the development of both the systems, of the main phases of their procurement and relevant results will be presented. The innovative aspects of their design will be highlighted: JT-60SA QPC represents the first application of hybrid mechanical-static technology for protection of superconducting magnets in fusion experiments and RWM-PS is the first PS system in fusion experiments adopting SiC semiconductors. The future work will be also discussed; outcomes from the operation of these systems, useful for ITER and DEMO, are expected.

Speaker: Dr Elena Gaio (Consorzio RFX)

Summary Slide FIP_P1-17.pdf

85 Control of NTMs and integrated multi-actuator control on TCV

Detailed experiments have been performed on TCV with its flexible electron cyclotron heating/current drive system to investigate reliable and efficient control of NTMs. For example, a novel sinusoidal sweeping technique has been studied in detail and we have shown for the first time that it is efficient for both NTM stabilization and preemption. This method is important for future devices as it relaxes the demand on the accuracy of the mode location estimation and the beam deposition calculation, and circumvents the need for extra diagnostics or many shots for tuning. Comparison between NTM preemption and stabilization has been achieved with sweeping and it shows that preemption can be more than twice as efficient as stabilization in terms of the necessary power. The reliable, efficient and generic control of NTMs allows the development of a controller working for all the scenarios and independent of the specialties of TCV, facilitating the integration with other real-time (RT) algorithms. RT control of NTMs, beta and model-estimated q profiles have been achieved simultaneously on TCV for the first time with a generic integrated control framework that consists of a hierarchy of state estimation/prediction, plasma event monitoring, supervision, high-level (HL-) actuator management (AM), generic controllers and low-level (LL-) AM. In an integrated control test, RT diagnostics are used with RT simulations to reconstruct the plasma state. We will show how RT analyses of magnetic signals are used to provide details of the mode, the RAPTOR observer to reconstruct electron temperature and q profiles, the RAPDENS-observer to generate density profiles and RT-TORBEAM to calculate beam depositions. This information is then used by the plasma event monitor to produce a finite-state representation of the plasma state based on user-defined thresholds. The supervisor prioritizes various tasks, activates relevant controllers and interfaces with a generic control layer. In this layer, controllers send requests for each task to the HL-AM that optimizes the actuator allocation and sends back the actuation capability to the controllers and the LL-AM. The LL-AM sends controller commands to the tokamak-specific actuators. Importantly, the control layer has been made tokamak agnostic to facilitate its reuse in other devices and to provide a layer of abstraction for operators.

Speaker: Mengdi Kong (ChSPC)

summary_slide_KONG_EX_P1_25_final.pdf

86 Design and Development of 500 kV, 100 mA DC High Voltage Power Supply for Particle Accelerators at IPR

At IPR Neutral Beam Injection (NBI) facility to heat and drive the plasma current in Tokamak is been built by accelerating the positive / negative ion beam of energy around 100 keV. Under the current R&D plan the projection is to develop the technology for future Mega Volt range DC Power Source facility to accelerate ion beam of energy to the tune of 1 MeV and power of the order of few MW. To meet this objective a compact 500 kV, 100 mA DC upgradable to 1000 kV Power supply is being designed and developed as a first step. This power supply shall also be used for several other applications within IPR related to particle accelerator. The 500 kV, 100 mA, 50 kW DC particle accelerator power supply is being designed using a symmetrical Cockcroft-Walton (CW) voltage multiplier topology owing to its design simplicity and economical construction. Other advantages of such cascade generators are: (a) low voltage rating of components, (b) balanced voltage w.r.t. ground, (c) gradual build-up of voltage, and (d) modular construction. The use of a high frequency power source gives an added advantage of low stored energy, less ripple, better regulation and faster response. A 415 V, 50 Hz 3-phase AC input source is converted into single phase high frequency (i.e. 20 kHz) source using IGBT based full H bridge inverter power supply rated for 100 kVA, 400 V (rms). The high frequency power supply charges the symmetrical CW voltage multiplier through a high voltage high frequency (HVHF) step-up center-tap ferrite core transformer rated for 80 kVA, 400 V / 25 kV – 0 – 25 kV (rms). The output voltage and current of the voltage multiplier unit are controlled by controlling the output voltage of the front end inverter operating in close loop control. This paper will present the design and simulation results of 500 kV, 100 mA DC Power Supply modeled in MATLAB Simscape toolbox. The paper will explain the optimization / sensitivity study performed in selecting and sizing of various active / passive components of CW voltage multiplier, inverter and step-up transformer taking into account the possible operational difficulties and future expansion. Both steady state and transient study results will be explained. This paper will briefly cover the engineering assembly design aspects of voltage multiplier unit in general and of a 250 kV prototype voltage multiplier developed.

Speaker: Mr ASHOK MANKANI (IPR)

87 Design and Development of Safety control system of Indian Test Facility (IN-TF) for ITER DNB

Indian Test Facility (IN-TF) [1] is being built in IPR to characterize Diagnostic Neutral Beam [2] in cooperation with ITER Organization. INTF is a complex system which consists of several plant systems like beam source, gas feed, vacuum, cryogenics and mechanical systems. To ensure successful operation INTF, integrated operation involving all the constituent plant systems is required. The experimental phases involve application of HV power supplies and High power RF power (~800KW) which will produce considerable amount of power (~6 MW) within the facility for longer durations. Hence the entire facility will be exposed high heat fluxes and RF radiations. For ensuring occupational safety for working personnel, it is of prime importance that a mature Safety control system [3] be developed and commissioned for INTF. The design of safety control system (SCS) is based on ITER PCDH guidelines and industrial standards for programmable safety systems (IEC 61511 and IEC 61508). The process of detailed design includes identification of safety instrumented functions (SIF), sensor selection and prototype development. The control hardware includes fault tolerant Siemens PLC with distributed interface on Profisafe protocol and safety software which is developed using Siemens safety programming environment. The SCS has to interface with the conventional INTF Control system (which is based on CODAC core system) for non critical data exchange. The SCS also dictate the overall mode of INTF operations. This paper describes the design methodology involved in arriving at final design with details of application of safety standards for identifying the Safety integrity levels (SIL) of SIFs and details of software level interface. The overall integrated system configuration and test results are also discussed. References: 1. M.J. Singh (2011, October). An Indian test facility to characterise diagnostic neutral beam for ITER, Fusion Engineering and Design.[Online].86,pp.732-735 2. A. Chakraborty (2010, March). Diagnostic Neutral Beam for ITER—Concept to Engineering. IEEE Trans. Plasma Sci.[Online].38(3), 3. H.Tyagi (2016, November). Preliminary design of safety and interlock system for Indian test facility of diagnostic neutral beam. Fusion Engineering and Design.[Online].(112).pp. 766-770

Speaker: Mr Himanshu Tyagi (ITER-India,IPR)

88 Design and development of the Articulated Robotic Inspection Arm (ARIA) for fusion machine

Remote Handling (RH) systems for maintenance and inspection of in-vessel components have been addressed in great detail for fusion machines around the world. Maintaining high availability of fusion machine and minimizing the maintenance time require robust and dependable RH systems. Such RH systems, being electro-mechanical in nature, requires research and development in various areas such as structural design, kinematic and dynamic modelling, efficient real-time control, and Virtual Reality (VR) based monitoring. Adding to the aforesaid requirements, is criticality of investment protection of the sophisticated in-vessel components and their size and weight scales. The Articulated Robotic Inspection Arm (ARIA) has been indigenously developed at IPR, India as a proof-of-concept for in-vessel maintenance. The paper presents, in detail, the design and development of the ARIA and associated VR based monitoring and control system. ARIA is a 6-Degrees of Freedom manipulator with a cantilevered payload capacity of ~25kg at 2meters distance. ARIA is controlled using a VR based user interface that immerses the ARIA model into the working environment. The effective 1:1 scale mapping of the VR model with the manipulator hardware makes provision for task planning and executing of the control commands from a remote location. The theoretical calculations with structural analysis of components like links, shafts, couplers, lugs and bearings are elaborately discussed. Results for payload sensitivity analysis during dynamic behavior are also presented. The system is optimized and developed to incorporate efficient commercially available servo actuators, bearings and gear-boxes, to maintain a high degree of accuracy and repeatability. Experimental validation and test results on a mock-up facility show that the system can be controlled with an end-effector positional accuracy within 2mm. The design and integration methodology, presented here, lays foundation to develop efficient RH systems with greater reach and payload capacity for future fusion machines.

Speaker: Mr Krishan Kumar Gotewal (Institute for Plasma Research)

Summary_A PERSPECTIVE ON REMOTE HANLDING EQUIPMENT ARIA DESIGN for fusion MACHINE APPLICATION.pdf

89 Design Validation of ITER XRCS Survey Spectrometer with Nuclear Code RCC-MR

In the ITER, systems are classified in the different safety categories as per their function in the machine; Protection Important Components (PIC) needs more attention during the design and analysis for better safety margins. The French Nuclear Code RCC-MR (2007) is employed in the design, analysis and the manufacturing, applicable to the ITER protection important mechanical components. It is always a challenge to the designers to develop and qualify the design for a PIC system under ITER loading conditions. This becomes even more stringent when the system is exposed to high nuclear radiation and performing the confinement function of radioactive tritium as in the case of X-Ray crystal spectroscopy (XRCS) Survey system. XRCS Survey diagnostics is an ITER PIC system, located in Equatorial port-11, will be used to monitor impurities in the highly ionized state and measure line emission from plasma in the X-ray range (0.1 to 10 nm). This system is connected with the Port Plug flange, due to its specific nature and exposed to complex environments of neutron radiation, high heat flux, electromagnetic forces, etc. To ensure the structural integrity of XRCS Survey from the constant loading (P Type damage), repeated loading (S type damage); we have studied various loads and associated load responses. These loads are broadly categorized in the following three types i) ITER Generic loads ii) Accidental loads and iii) Radiation loads. FE (ANSYS) analysis has been performed and design is validated using the French Nuclear design rules RCC-MR (2007). This paper describes results obtained from structural damage analysis of XRCS Survey system, and their compliance with relevant design rules given in the French Nuclear code RCC-MR validating the design. Topic name: Fusion Engineering, Integration and Power Plant Design

Speaker: Mr SIDDHARTH KUMAR (ITER INDIA)

Summary_slide_FEC-2018FIP_P1-36.pdf

Summary_slide_FEC-2018FIP_P1-36.pptx

90 Deuterium Depth Profile Measurement in Pre and Post Irradiated Tungsten

Tungsten (W) will be used in ITER as a Plasma Facing Material (PFM) in divertor due to its capability to handle high heat flux while having a low Hydrogen (H) isotope affinity. However in presence of fusion neutrons and alpha particles, tungsten can accumulate radiation damage, which might significantly enhance its H retention property. In order to investigate the effects of radiation damage on Deuterium (D) trapping in tungsten, we have carried out experiments using D beam in pre and post irradiated polycrystalline tungsten foils. In this paper we present the comparison of D depth profile measurements using Elastic Recoil Detection Analysis (ERDA) and Secondary Ion Mass Spectroscopy (SIMS) technique.

Polycrystalline tungsten foil samples of size 8mmx8mmx0.1mm foils were mechanically polished and annealed at 1838 K to release the stress and to minimize the defects. These foils were further irradiated with gold ion (80 MeV), boron ions (10 MeV) to create defects. These samples were then exposed to a D beam of 100keV energy for a fluence of 5x1017 ions/cm2. The trapped D was measured using ERDA and SIMS, and the depth profiles were modelled using binary collisions Monte Carlo method by including the surface roughness. The preliminary results show the enhancement in amount of trapped D in pre-damaged tungsten samples in contrast to the undamaged ones. The effect of Helium (He) on D trapping in sample was also analyzed and it was observed that D trapping is reduced in presence of He. The details of experiments and the analysis will be presented.

Speakers: Dr Anil Tyagi (ITER-India, Institute for Plasma Research), Mr Matteo Barbarino

summary slide.pptx

91 Development of a High Temperature Black Body Source for ITER ECE Diagnostic

For ITER Electron Cyclotron Emission (ECE) diagnostic, there is a requirement of high-temperature black body radiation source operating at atmospheric pressure. This source needs to be operated at high temperature (~ 500 0C) having a microwave emissivity > 0.95 in the frequency band 100-500 GHz, and > 0.75 for 500-1000 GHz. Moreover, the radiation surface should have temperature uniformity within ±10 0C. This source will be utilized for characterizing the ITER ECE measuring instruments like Michelson Interferometer and radiometer. For this purpose, a radiation source has been designed and developed. The radiation source consists of a heater and an emissive surface. The emissive surface is made of silicon carbide (SiC), as it has high thermal conductivity, low thermal coefficient of expansion, excellent machinability, good vacuum compatibility and high emissivity in the mm-wave region. The diameter of the emissive surface is 150 mm.The suitable heating element has been used having high resistivity and good oxidation resistance nature. This paper deals with the design, analysis, and characterization of the developed high-temperature black body radiation source in the frequency range 100 to 1000 GHz. The Finite Element Method based software, “COMSOL”, has been used to analyze and optimise the heating coil design to get desired temperature uniformity of the emissive surface. Experimentally, the temperature uniformity is measured by an IR camera and microwave emissivity is measured by the Michelson interferometer.The operating temperature of 500 0C is achieved in the developed source with temperature uniformity within ±10 0C. The short and long-term temperature stability up to ± 2 0C and ± 10 0C respectively has also been achieved. Further, the microwave emissivity of ~0.8 - 0.9 has been observed over wideband 100-1000 GHz. The above measured values are in compliance with ITER requirement.

Speaker: Mr RAVINDER KUMAR (ITER-INDIA,INSTITUTE FOR PLASMA RESEARCH)

Summary Slide.pdf

92 Development of High Power Gyrotrons for Advanced Fusion Devices and DEMO

Megawatt (MW) gyrotrons with a wide frequency range from 14 to 300 GHz are being developed in a collaborative ECH study for advanced fusion devices and a DEMO. (1) Detailed designs of a 14 GHz 1 MW gyrotron has been started for actual fabrication. For a 14 GHz RF beam with high divergence, a calculated transmission efficiency of 85% to the corrugated waveguide coupling position was initially obtained by minimizing the RF transmission path. (2) In the experimental tests of a new 28/35 GHz dual-frequency gyrotron, the cooling characteristics of an optimal-structure double-disk sapphire window was evaluated. We confirmed that operating at 0.4 MW with a continuous wave (CW) at 28 GHz is possible, which is two times the output power reported in previous studies. (3) A 77/51 GHz dual-frequency gyrotron with an output of over 1 MW is presented. (4) In an experiment with a 300 GHz gyrotron, the influence of the reflected wave from the window was reduced by tilting the output window, and mode competition in the cavity was suppressed. An output power of 0.62 MW with a pulse width of 1 ms, which is the new record in this frequency, was obtained.

Speaker: Dr Tsuyoshi Kariya (Plasma Research Center, University of Tsukuba)

CN258_Summary_FIP_P1-56_Kariya.pdf

93 Development of the far-infrared laser polarimetry for current profile measurement on ITER

The authors are demonstrating the key technology necessary for the ITER poloidal polarimeter (PoPola) in order to measure the plasma current profile in ITER. The entire optical train of a prototype channel was made to evaluate the performance of the laser alignment system and the stability of the polarization measurement. The PoPola system injects multiple far-infrared (FIR) laser beams into the plasmas (wavelength is 119 μm) and those probing beams are reflected by retro-reflectors (RRs). The polarization state of the FIR laser beams returning to the diagnostic room are measured by means of the rotating waveplate Stokes polarimeter (RWS polarimeter). The RWS polarimeter technique measures both orientation angle (θ) and ellipticity angle (ε) of the polarization state. Changes in θ and ε, which are mainly associated with the Faraday and the Cotton-Mouton effects, provide information of electron density, electron temperature and magnetic field. Equilibrium reconstruction of PoPola measurement data together with other ITER diagnostics data provides the current profile. Since the RWS polarimeter technique does not use interference signal of a probing and a reference beam, it does not need to take care about wave front distortion of laser beams and change of path length difference between the probing and the reference beam. However, the RWS polarimeter technique needs higher power (~10 μW) of the laser beam returning to a detector than other polarimeter based on interferometer. Key technologies for getting high power of the returning laser beam are a retro-reflector and a laser beam alignment system. Prototypes of the tungsten RR was made of a tungsten mono-block by machining and the angle between orthogonal mirrors was 89.9167°. Taking into account the thermal expansion during the plasma operation, the achieved manufacturing tolerance is promising. We developed the laser beam alignment method in order to minimize the loss due to shading at the vacuum window and RR. When the laser beam is tilted within +/- 1 mrad for the sake of searching the RR center, the beam position displacement at the vacuum window was 2.0 mm or less. The alignment error above leads to the laser power loss of 4 % owing to shading and acceptable.

Speaker: Dr Ryota Imazawa (National Institutes for Quantun and Radiological Science and Technology)

summary_imazawa_FIP_P1-14.pdf

94 Dielectric windows as front-end diagnostic elements in ITER

The performance of front-end elements of optical diagnostics in ITER under long-term operation and with limited access for their maintenance is in the focus of extensive R&D program involving laboratory study and testing in working tokamaks. The requirements to the front-end element design are driven by high-energy neutron and gamma radiation, intense particle fluxes and thermal loads at the element location on the one hand and necessity to provide periodic or continuous surface recovery on another. The insulating diagnostic window as an alternative to commonly accepted first mirror option is discussed in the presentation. The approach implementation is illustrated for the divertor Thomson scattering (DTS) optical scheme using front-end windows for injection of laser beam and collecting of scattered light. Surface recovery techniques based on plasma cleaning and laser ablation are described with the focus on the performance of the windows under laser and plasma treatment. The windows made from fused silica glass KU-1 and Al2O3 were tested. Plasma cleaning experiments have been performed for clean windows and windows coated with Al films. As was shown by the means of optical microscopy, XPS and AFM the dominant mechanism of window optical degradation is surface roughening. The development of surface relief becomes more intensive after deposition and removal of Al. The clear indication of the dependence of surface degradation rate on the initial polishing quality was also obtained for the windows with and without Al deposition. Laser experiments reveal the decrease in laser-induced damage threshold by the factor of~ 3 for both window materials under continuous tungsten deposition. In the case of Al droplets spraying, damage threshold is about 6 times as low as that of pure KU-1 window. The experiments on the long-term laser cleaning under continuous contamination showed that the evolution of tungsten film stops over the first hundreds of pulses and further exposition has no effect on the film thickness. The steady-state thickness of tungsten deposit in the beam spot was found to be ~ 5 nm for the deposition rate of ~10nm/min and laser (3 ns) energy density of ~ 2 J/cm2, forming almost transparent coating in visible and near-IR regions. Radiation-induced effects in silica glass and sapphire and corresponding limitations are also discussed.

Speaker: Mr Alexey Razdobarin (Ioffe Institute)

95 Divertor impurity seeding experiments at the COMPASS tokamak

Partial detachment is the desired regime for the baseline burning plasma scenario in ITER and next–step devices, as it allows to convert the majority of the energy carried by charged particles through the scrape-off-layer (SOL) into isotropic radiation and thus avoids localized heat flux deposition in the divertor region. In order to maintain relevance to ITER and DEMO, a concentrated effort has been initiated at the COMPASS tokamak to achieve detached operation by means of impurity seeding. Series of experiments with impurity injection in the range of 2-9x1020 molecules per second at different locations in the divertor were performed with the aim to cool the plasma and influence the particle and heat transport in the divertor region and provoke partial detachment. Previously reported results [1] were largely extended by injection of nitrogen at the outer divertor target and also by attempts to seed the plasma with neon. The effects on SOL and divertor plasma conditions were monitored by means of horizontal reciprocating probe manipulator located at the outer midplane and by arrays of divertor Langmuir and Ball-pen probes. The radiation in the edge plasma was observed by AXUV bolometers and fast visible cameras. Experiments in L-mode discharges with nitrogen injected at the outer divertor target have shown that the presence of radiating impurity leads to drop of pressure in the divertor. Depending on the magnitude of the seeding, the upstream pressure can be also affected, suggesting possible penetration of nitrogen into the confined plasma region. The target pressure, however drops at faster rate than upstream, which allows to reach the regime of partial detachment. Similar results were obtained by the HFS nitrogen injection, however the change in divertor pressure was more generally more abrupt and was less sensitive to the amount of injected nitrogen. References: [1] M. Komm et al., proceedings of the 44th EPS conference, Belfast (2017) P1.118

Speaker: Dr Michael Komm (Institute of Plasma Physics of the Czech Academy of Sciences)

96 Dynamic Simulation of Loss of Insulation Vacuum Event for ITER Cryodistribution System

The Auxiliary Cold Boxes (ACBs) of the ITER cryodistribution system has multiple cryogenic process volumes as well as interfaces with cryolines with isolated vacuum spaces. The cryogenic process volumes inside a single vacuum space have different temperature level, 4 K and 80 K as well as different operating pressure, 0.5 MPa and 1.8 MPa. The cryogenic process volumes including interfacing cryolines are protected with safety relief valves (SRVs). In the event of Loss of Insulation Vacuum (LIV) of any particular vacuum space, the incidental heat load of the order of ~6.5 kW/m2 results in rapid pressurization of the cryogenic process volume and pressure must be relieved through SRV. As per the safety requirements of the ITER, the maximum helium inventory inside the tokamak building is restricted and therefore a common relief header is necessary for collecting the release of helium through SRV and carrying it outside the tokomak building. The sizing of the SRVs is performed for the various scenarios as per applicable standard; however, due to the long length of relief header, the required information regarding back pressure on the SRVs is not known in advance. The back pressure is an important parameter to be considered for the sizing and selection of SRV and is a function of geometric condition of relief header, process condition of relieving process volume and relieving mass flow rate. Estimation of back pressure considering steady state condition and maximum mass flowrate through SRV may results in a conservative and unrealistic value of back pressure. Dynamic simulation of the safety relief event along with the complete model of process volume, correct boundary conditions as well as geometric detail of relief header is developed and analyzed based on pressure flow solver model in Aspen HYSYS®. Results are presented for the most demanding scenario viz. LIV event of the largest cryoline and comparison made with the two approaches of back pressure prediction, one with steady state and the other with dynamic simulation model. Results obtained from the dynamic simulation of the entire safety relief system gave useful results at various locations; moreover, the back pressure on SRV is almost half of the back pressure resulted from the steady state approach. Certainly, the dynamic simulation provided valuable inputs for the overall system configuration.

Speaker: Mr SRINIVASA MURALIDHARA (ITER-INDIA)

97 Early identification of disruption paths for prevention and avoidance

Disruption prevention in the perspective of high performance, high current, long duration plasma discharges requires a substantial evolution of the schemes applied in most of the present tokamaks. An efficient prevention scheme requires the early identification of the nature of the off-normal behavior possibly leading to a disruption and the automatic selection of the appropriated countermeasure, either avoidance or mitigation. The development of such comprehensive scheme is being pursued in a coordinate effort. For the purpose of the avoidance, on which this paper is focused, the disruption can be seen as the result of the interplay of the physical events and of the control system responses to them and to the technical failures. The building blocks of such description should include the integration of several sets of plasma scalar data, plasma profile data, magneto-hydrodynamics indicators and engineering data. Previous work has shown the potential of the Generative Topographic Mapping (GTM) [Bishop C., Neural Comp. 10, 1998] algorithm for identification and discrimination of the disruptive operational space in tokamak devices [Pau A.,Ph.D Thesis, paduaresearch.cab.unipd.it/6664/, 2014; Cannas B., PPCF56, 2014] . In this paper it is shown that the magnetic fluctuations associated with rotating MHD modes can be characterized using a set of observables derived from the Singular Value Decomposition applied to the data collected by an array of pick-up coils. They can provide an input to the GTM analysis such that a clustering separating disruptive and non-disruptive timeslices can be found. A further source of information comes from the analysis of the sequences of events recorded by the machine control system. The analysis of such sequences shows that disruptions and non-disruptive terminations generally follow different paths, i.e. are not populating equally the same sequences. Moreover, the time analysis of the most populated disruptions paths shows that in most of the cases the sequence can be recognized with an advance ranging about from 0.15s to 1.5s with respect to the disruption time. Such information is readily available to the control system and can contribute to the early triggering of the avoidance action. Details of such combined analysis and application to different databases of JET, TCV and AUG tokamaks will be discussed in the paper.

Speaker: Dr Carlo Sozzi (Istituto di Fisica del Plasma - CNR, Milano, Italy)

sozzi-summary-slide_EX-P1-22.pdf

98 Effect of magnetic shear and the finite banana-orbit width on the neoclassical toroidal viscosity in perturbed tokamaks

The effect of magnetic perturbations on the rotation profile in tokamak has been studied both experimentally and theoretically, since the prediction and control of the plasma rotation is one of the key issues for the stable operation. The NTV torque caused by magnetic perturbations is evaluated by adopting either a local or global drift-kinetic models. In the local models, the finiteness of the drift orbit width is neglected, and the magnetic-shear dependence of the precession frequency $\omega_B$ has been omitted. However, recent studies have found that the NTV evaluated from the global simulations, which keep the finite-orbit-width (FOW) effect and the magnetic-shear effect, are different from what the local models predict. Therefore, understanding the reason of this discrepancy in the NTV calculations is important. Here, by comparing global and local simulations, the FOW effect and the magnetic-shear effect are investigated. To study these two effects separately, we prepared two local simulation models, one neglects the magnetic-shear effect while the other keeps it in the evaluation of $\omega_B$. For electrons, it is found that the NTV profiles from the global and local codes are similar. Strong resonance of drift motions with the perturbed field occurs if $\omega_B\simeq 0$, which causes the strong NTV in low-collisionality regimes. $\omega_B$ depends on the magnetic moment and the local shear. The resonant condition in the velocity space approaches to the trapped-passing boundary as the local magnetic shear becomes more positive. In the positive-shear case, the resonant orbits are easily disturbed by small collisions and therefore the NTV evaluated by the global model tends to be smaller than that by the local one. Opposite tendency can be seen in the negative-shear case. For ions, it is found that the difference in NTV between local and global simulation becomes significant and is caused not only by the magnetic-shear effect but also by the FOW effect. In the global calculation, trapped particles see the spatial variation of the magnetic perturbations along the perturbed drift motions, while the local model assumes that a trapped particle bounces along an unperturbed field line. The non-local effect causes a significant difference in the ion NTV and in the rotation profile predicted from global and local simulations.

Speaker: Dr Shinsuke Satake (National Institute for Fusion Science, Japan)

iaea-onepage_satake.pdf

99 Electromagnetic Particle Injector (EPI) as a Fast Time Response Disruption Mitigation Concept

The Electromagnetic Particle Injector (EPI) has the potential for delivering the radiative payload to the plasma center on a 3-4 ms time scale, much faster, and deeper, than what can be achieved using present methods. Predicting and controlling disruptions is an important and urgent issue for ITER. While a primary focus is the early prediction and avoidance of conditions favorable to a disruption, it is understood that some disruptions may be inescapable. For these cases, a fast time response method is essential to protect the ITER facility. Experimental tests on a proto-type system have been able to verify the predicted rapid response capability of the EPI system by accelerating a 3.2 g sabot to 150 m/s in 1.5 ms.

The primary advantage of the EPI concept over present systems is its ability to meet short warning time scales while accurately delivering a radiative payload composed of acceptable low-Z materials such as Be, B or BN. This is done at velocities of ≥ 1 km/s required to achieve core penetration in high power ITER discharges, thus providing thermal and runaway current mitigation. This capability will provide the means for initiating a controlled plasma termination that originates at the plasma center, rather than from the outer periphery. This added capability, in addition to the fast time-response capability, should provide greater flexibility in controlling tokamak disruptions.

*This work is supported by U.S. DOE Contracts: DE-AC02-09CH11466, DE-FG02-99ER54519 AM08, and DE-SC0006757.

Speaker: Dr Jonathan Menard (Princeton Plasma Physics Laboratory)

Raman.R-FIP-P1-51-SummarySlide.pptx

100 Erosion and deposition in the JET divertor during the ITER-like wall campaigns

During JET operation with all carbon walls prior to 2010 (JET-C) massive re-deposition of previously eroded carbon was observed in the divertor and in remote divertor areas. This massive carbon re-deposition was accompanied by a high retention of hydrogen isotopes trapped by co-deposition. Extrapolations of these results to ITER predicted very high potential tritium retention, resulting in the decision to remove carbon from the ITER divertor. One aim of the JET ITER-like wall (JET-ILW) project was to study plasma-surface interactions in a carbon-free beryllium/tungsten environment comparable to the ITER material configuration. All divertor tiles were manufactured either from tungsten coated carbon-fibre composite (CFC) material or from bulk tungsten. Erosion and deposition in the JET divertor were studied during the campaigns JET-ILW1 (2011-2012), ILW-2 (2013-2014) and ILW-3 (2015-2016) by using specially prepared divertor marker tiles using W/Mo marker layers, which were analysed before and after the campaign using elastic backscattering of 3 and 4.5 MeV incident protons and nuclear reaction analysis using 0.8 to 4.5 MeV $^3$He ions. The erosion/deposition pattern observed with the JET-ILW configuration shows partly drastic changes compared to the pattern observed with JET-C: The total material deposition rate in the divertor decreased by a factor of 4–9 compared to the deposition rate of carbon in JET-C. This decrease of material deposition in the divertor is accompanied by a decrease of total deuterium retention inside the JET vessel by a factor of about 20. The erosion/deposition pattern observed during JET ILW-2 was qualitatively comparable to JET ILW-1, the observed D inventory was roughly comparable to the inventory observed during JET ILW-1. The results obtained during JET ILW-2 therefore confirm the positive results observed in JET ILW-1. Early results from JET ILW-3 also indicate agreement; more details will become available in summer 2018.

Speaker: Dr Matej Mayer (Max-Planck-Institut für Plasmaphysik)

Mayer_Summary_Slide.pptx

101 Exhaust Behavior and Mass Balance of Tritium in Large Helical Device

The control and management of tritium in a fusion test facility is one of the important issues from the viewpoints of radiation safety and public acceptance. As for the tritium control in a fusion test device, understanding of tritium behavior in the exhaust gas would give us new knowledge into the characteristics of the tritium release and inventory. In the deuterium plasma experiment on the Large Helical Device (LHD) which has the stainless based first wall, a small amount of tritium is produced by deuterium-deuterium reaction in the core plasma and it can be used as a tracer. A portion of produced tritium is exhausted from the vacuum vessel via the vacuum pumping system. To investigate the tritium behavior, the tritium in the exhaust gas was monitored by a water bubbler system for discriminating chemical forms and an ionization chamber. In the exhaust gas from LHD, the chemical forms of tritiated hydrogen gas was more than 95% and the tritiated hydrocarbons was a few %. Since the divertor tiles are made of carbon, a part of tritium was incorporated into the hydrocarbons by chemical sputtering. The ratio of tritiated hydrocarbon exhaust gas was less than that in JT-60U which has carbon-based first wall. On the other hands, the tritium in the plasma facing component was released by the He and D2 glow discharge cleaning operation. The tritium release mechanism was supposed to the hydrogen isotope exchange reaction and diffusion limited process. The tritium exhaust rate was gradually increased with the progress of deuterium experiment. Then, the total amount of exhausted tritium was approximately 35.5% of produced tritium at the end of the plasma experimental campaign. It suggested that two-thirds of produced tritium would be implanted in the first wall. The ratio of exhaust tritium during plasma experiment in LHD was about 1.5 times larger than that of JT-60U. Thus, the metal first wall would reduce the tritium inventory in the fusion machine. The tritium tracer study in the first deuterium plasma experiment in LHD revealed that (i) the tritium on the surface was removed by hydrogen isotope exchange reaction and the tritium release from plasma facing component was diffusion limited process, and (ii) The metal wall is one of key factors to control the tritium inventory and to reduce the tritium compounds in exhaust gas.

Speaker: Dr Masahiro Tanaka (National Institute for Fusion Science)

Summary.pptx

102 Experimental Measurements of Cryogenic Heat Loads on SST-1 Helium Cryogenic Plant

The SST-1 cryostat houses 130 thermal shields cooled using liquid nitrogen, 16 toroidal field (TF) coils, 9 poloidal field (PF) coils and their associated support structures. Superconducting Magnets System (SCMS) of the SST-1 consisting of TF and PF coils is designed to cool with forced flow supercritical helium (SHe) at 4 bar (a), 4.5 K and a mass flow rate of 300 g/s using helium refrigerator-cum-liquefier (HRL) of 1.3 kW equivalent cold power at 4.5 K. Last several campaigns, we have observed that the TF and PF coils could not be simultaneously cooled to 4.5 K due to heat loads from SCMS exceeding the installed cryogenic capacity of HRL. In order to cool the TF coils system at desired conditions of 4.5 K, we had to isolate PF coils as well as TF Case hydraulics from HRL at intermediate temperatures of ~ 20 K. In this specific case, the PF coils and TF Case surfaces would be at elevated temperatures in the range of 40 K – 50 K. To ascertain overall heat loads from SCMS, its associated supports structure along with the cryogenic distribution system under different cooling scenarios on SST-1 helium cryogenic plant, we have recently conducted a dedicated campaign. In this experiment, we demonstrate cool down of TF magnets in single phase supercritical helium mode to ~ 5 K for the first time. Helium supply pressure, temperature and mass flow rate are measured at the outlet of HRL before it is fed to SCMS while helium return temperature and pressure from SCMS are recorded at return line of HRL. This gives a clear picture of equivalent heat loads on HRL system. The cryogenic heat load is found to be ~ 1286 - 1350 W (+/-3%) at 5.5 K under single phase flow conditions. In the same campaign we have succeeded to cool all the nine PF coils to ~ 5 K by isolating TF coils from HRL for the first time. In this work, we report the experimental measurement procedure, instrumentation details and heat load data analysis. These results serve useful purpose in assessing the net cooling power requirement for the simultaneous cooling of the TF and PF coils and facilitate long duration plasma experiments in future.

Speaker: Mr Nitin Bairagi (Institute for Plasma Research)

Summary.pptx

103 Experimental studies of pressure and plasma current profiles for equilibria calculations during AC transition in the ISTTOK tokamak

In general, the operation of AC discharges in small tokamaks requires the control of a few external parameters such as vertical and horizontal fields, external heating (where available), chamber conditioning and gas puff. The dynamics and type of control used are mostly based on experimental empirical learning, with different combinations of actuators depending on the tokamak device. Experimental studies performed during the AC operation in the ISTTOK tokamak have addressed the influence of several control parameters in the success of the AC transition. Although the link between the different external actuators and plasma discharge evolution could be verified, successful AC transitions above 4 kA plasma current could not be achieved. In order to build a more predictive control of the AC transition it would be useful to develop a first principles model which interprets the experimental observations. Such model would need to combine experimental data and calculations on the equilibria and stability in several time stamps of the transition, current profile evolution, ramp-up and runaway generation, drift electrons, and the electro-technical properties of the tokamak during AC operation. The output of such model would inform the discharge controller how to balance evolution of the external actuators during the AC transition.
The present paper presents an initial step towards the development of a deeper understanding of the equilibria and current profile during the AC transition in ISTTOK. The goal of the present study is to identify the topology of flux surfaces based on experimental pressure-like measurements and matched current profiles, the existence (or not) of antiparallel plasma currents during transition and the existence of drifting electrons and their role during current ramp-up. There is also experimental evidence on the presence of fast electrons (possibly a significant run-away fraction) playing an important role during the initial stages of the discharge immediately after the transition. This will be further investigated using colisonless numerical simulations to determine the maximum lifetime of the drift electrons and their response to H-V fields. It is important to use this electron population in combination with gas puff to produce a more efficient Townsend avalanche during the current ramp-up.

Speaker: Dr Matthew John Hole (Australian National University)

slide.pdf

104 Exploring Deuterium Beam Operation and Behavior of Co-Extracted Electron in Negative-Ion-Based Neutral Beam Injector

Deuterium beam operation of the negative-ion-based neutral beam injector (N-NBI) was initiated in the Large Helical Device (LHD) in 2017. Both hydrogen (H) and deuterium (D) neutral beams were generated by changing the operation gas using the same accelerator. Comparison of the beam properties such as the extracted negative ion current and the co-extracted electron current, obtained with $\rm H_{2}$ and $\rm D_{2}$ gases, will clarify the production and extraction mechanism of the negative ions. Remarkable results are as follows: (i) 46 A deuterium negative ion current ($I_{D^-}$) has been extracted with the averaged negative ion current density of 190 A/m$^2$ by two negative ion sources in the injector. (ii) The current ratio of co-extracted electrons to negative ions ($I_e/I_{D^-}$) was 0.39 using 0.43 Pa source gas pressure. Although the configuration of the ion source is not optimized for D, the observed current of D$^-$ ions reached 82 % of the LHD requirement and those results were comparable to the ITER-NBI specification ($I_{D^-}$ = 40 A with the current density of 200 A/m$^2$ at 0.3 Pa). (iii) Linear dependence of the minimum value of the $I_e/I_{D^-}$ on the arc-discharge power is found, and is stronger in the D$^-$ operation than $I_e/I_{H^-}$ in the H$^-$ operation. The degradations of the negative ion current and the increase in the co-extracted electrons are probably caused by decrease of the surface production rate of D$^-$ ions which strongly depends on the incident D$^0$ atom velocity to the plasma grid (PG) surface. In addition, caesium (Cs) sputtering became enhanced in the deuterium discharge. This Cs behavior suggests that larger energy transfer by the deuterium ions impinging onto the PG surface removes the Cs layer required for surface production of the negative ions. These features could be a technical issue in D$^-$ beam operation in future NBI where a higher power and a longer pulse duration are required.

Speaker: Dr Katsunori Ikeda (JpNIFS)

Poster.pptx

summary_ikeda_NIFS.pptx

105 Extension of the Operating Space of High-“β_N” Fully Non-inductive Scenarios on TCV Using Neutral Beam Injection

The fully non-inductive sustainment (“V_loop~0") of high normalized beta (“β_N”) plasmas is a crucial challenge for the steady-state operation of a tokamak reactor. In order to assess the difficulties associated with such scenarios, steady-state regimes have been explored on TCV using the newly available 1MW Neutral Beam Injection (NBI) system. Compared to the past [O. Sauter et al Phys. Rev. Lett. 84(15) 3322 (2000), S. Coda et al Phys. of Plasmas 12 056124 (2005)], plasmas closer to those expected in ITER, i.e. with significant NBI and ECRH current drive, bootstrap current and fast ion fraction, have been investigated. The operating space has been explored by carefully scanning the total auxiliary power “P_aux=P_EC+P_NB”, the NB power fraction (“P_NB/P_aux”) and the radial deposition location of the NB and EC heating and current drive. “β_N” values up to 1.4 and 1.7 at “V_loop~0” have been reached in L-mode and H-mode plasmas, respectively. Fully non-inductive operation was not achieved with NB alone, whose injection could even increase “V_loop” in presence of EC waves. Internal Transport Barriers, which are expected to maximize the boostrap current fraction, were not formed in either the electron or the ion channel in the plasmas explored to date; and this despite a significant increase in the toroidal rotation and Fast Ion (FI) fraction with NBI, which are known to reduce turbulence [J. Garcia et al Nucl. Fusion 55 (2015) 053007]. The possibility that these plasmas are Trapped Electron Mode (TEM) turbulence dominated is being analysed in dedicated transport analyses. A strong contribution of bulk and FIs to the total plasma pressure has been experimentally evidenced and confirmed by modelling (ASTRA, NUBEAM). Interpretative simulations further predict that FI charge-exchange reactions are the main loss channel for NB heating efficiency. Similar results were also obtained in inductive L-mode plasmas in a circular limited configuration at TCV [B. Geiger et al Plasma Phys. Control. Fusion 509 115002 (2017)]. Interpretative transport analysis with TRANSP coupled to NUBEAM is carried out to quantify the role of NBI losses and of the anisotropy in the FI velocity space distribution in the NBCD efficiency. A complete understanding of this evidence is crucial to the development of fully non-inductive plasmas

Speaker: Dr Chiara Piron (ItRFX)

summary_slide_IAEA_cpiron.pdf

106 Extrapolation of Be Erosion Modelling from JET and PISCES-B to ITER

Beryllium (Be) erosion data is one of the key issues for ITER including the first wall (FW) life time predictions [1], which undergo a re-visit based on the recent studies at the existing devices: tokamak JET equipped with the ITER-like wall (ILW) and linear plasma device PISCES-B. The extrapolation of physical and chemically assisted sputtering data is based on interpretive and predictive numerical modelling by the 3D plasma-surface interaction and impurity transport ERO code. One of the key elements is the proper treatment of the sputtering ion trajectories in the magnetic sheath, determining the angle and energy distributions by impact with the surface, and, thus the effective local sputtering yield. This recent improvement has helped to resolve the discrepancy in the normal incidence part of the factorized physical sputtering yields, which were interpreted using ERO from the JET-ILW and PISCES-B measurements. The uncertainties due to plasma-facing surface temperature and fuel e.g. deuterium (D) content in the wall are considered. The D content in plasma-wetted areas was shown to be large (the yields based on the assumed 50%D surface content, which are smaller by about a factor 3-4 than for the pure Be, lead to the best agreement with experiments). This means that the most optimistic of ITER life time predictions [1] of 4200 baseline Q=10 yields discharges based on the lowest yields (50%D) is confirmed, though somewhat corrected down due to the improved sheath model. It is important, however, to emphasize that the zero order uncertainty in these FW net erosion predictions originates in the background plasma specification which remains significant for the ITER far-SOL plasma. The advantages of the new massive-parallel ERO2.0 which allows treating the whole of JET-ILW or ITER volume, and thus providing self-consistent treatment of self-sputtering and magnetic shadowing are an additional motivation for the revisit of [1]. Furthermore, ERO2.0 enables cross-check between diagnostics, e.g. spectroscopic sightlines and filtered images from 2D cameras characterizing Be influx and plasma content, or IR images mimicking heat load distributions. Related predictive simulations of Be impurity light emission can assist in designing (sensitivity and stray light issues) the ITER visual range spectroscopy systems. [1] D.Borodin et al., 2011 Phys. Scr. T145 14008

Speaker: Dr Dmitriy Borodin (Forschungszentrum Jülich GmbH, Institut für Energie- und Klimaforschung IEK-4: Plasmaphysik)

DBorodin_FEC2018slide_v2.pptx

FEC2018pap_DBorodin_v7sub2.docx

FEC2018pap_DBorodin_v7sub2.pdf

107 First Mirror Test in JET for ITER: Complete overview after three campaigns in JET with ITER-like wall

Metallic first mirrors are essential plasma-facing components (PFC) in all optical spectroscopy and imaging systems used for plasma diagnosis. First Mirror Test (FMT) has been carried out at the JET tokamak with the ITER-like wall (JET-ILW). Over 120 test Mo mirrors were exposed in JET during the entire project. The aim is to provide an overview of results obtained for mirrors exposed during: (i) the third ILW campaign, ILW3, 2015-2016, 23.6 h plasma; (ii) all three campaigns, i.e. ILW 1-3: 2011-2016, 62h in total and (iii) a comparison to results in JET-C. Examinations were done by optical, electron and ion beam techniques. The total reflectivity of all mirrors in the main chamber has decreased by 2-3% from the initial value. All of them are coated by a very thin co-deposit (5-15 nm) containing D, Be, C and O. This has affected the optically active layer (15-20 nm on Mo) and led to increased diffuse reflectivity. No W and N have been found on the surface. All mirrors from the divertor lost reflectivity by 20-80%. There are significant differences in the surface state dependent on the location and exposure time. Reflectivity loss is connected predominantly with the co-deposition of Be and some C species. The thickest layers have been found in the outer divertor: 850 nm after ILW1-3, indicating the average growth rate of 4 pm s-1. The layers thickness is not directly proportional to the exposure time. Nitrogen, tungsten and nickel are on all mirrors from the divertor. The highest N and W contents are in the inner divertor: N reaches 1×1017 cm-2, W is up to 3.0×1016 cm-2, while the greatest Ni content is in the outer leg: 2.5×1017 cm-2. The results obtained for the main chamber mirrors allow some optimism regarding the diagnostics reliability in ITER. Tests done in JET-C and JET-ILW show that the degradation of optical properties in a machine with metal PFC is distinctly smaller than in the carbon surrounding. However, a long-term exposure and off-normal events may change surface properties of the mirrors. Laser- or plasma-induced cleaning techniques of tokamak mirrors have not brought any positive results. There are some indications that single crystal mirrors may be cleaned more efficiently than polycrystalline. Search for engineering solutions for mirror exchange in a reactor should not be abandoned especially for the divertor mirrors.

Speaker: Mr Stefan Jachmich (BeLPP)

108 High fusion performance at high Ti/Te in JET-ILW baseline plasmas with high NBI heating power and low gas puffing

This paper presents the transport analysis of high density baseline discharges in the 2016 experimental campaign of the Joint European Torus with the ITER-Like Wall (JET-ILW), where a significant increase in the Deuterium-Deuterium (D-D) fusion neutron rate (~2.8 x 1016 sec-1) was achieved with stable high Neutral Beam Injection (NBI) powers of up to 28MW and low gas puffing. Increase in Ti exceeding Te were produced for the first time in baseline discharges despite the high electron density, and this enabled a significant increase in the thermal fusion reaction rate. As a result, the new achieved record in fusion performance was much higher than the previous record in the same heating power baseline discharges where Ti=Te. In addition to the decreases in collisionality and the increases in ion heating fraction in the discharges with high NBI power, Ti > Te can also be attributed to positive feedback between the high Ti/Te ratio and stabilisation of the turbulent heat flux resulting from the Ion Temperature Gradient (ITG) driven mode. The high Ti/Te ratio was correlated with high rotation frequency. Among the discharges with identical beam heating power, higher rotation frequencies were observed when particle fuelling was provided by low gas puffing and pellet injection. This reveals that particle fuelling played a key role for achieving high Ti/Te, and the improved fusion performance. The impact of particle fuelling on high Ti/Te has an important implication for 2019 D-T experimental campaign, as it can provide a further increase in the fusion performance with the present heating power capability.

Speaker: Dr Hyun-Tae Kim (EUROfusion Consortium JET)

High fusion performance at high T i/T e in JET-ILW baseline plasmas with high NBI heating power and low gas puffing

109 Hollow pellets for magnetic fusion

Motivated by edge localized mode (ELM) control in H-mode plasmas, we summarize experimental and theoretical progress in MHD physics of plasma interaction with small pellets ranging from 10s of microns to a few mm in size. Layered spherical structures with a hollow core (“hollow pellets”) are attractive in comparison with solid spheres and gas puffing. Theoretical results based on multi-fluid calculations of pellet-induced cold plasmoid formation and interactions with background plasmas are given. The experimental results include a new dual-spectroscopy technique for imaging of ELMs and fabrication of prototype hollow pellets.

Speaker: Dr Zhehui Wang (Los Alamos National Laboratory)

IAEASummary v2.pdf

110 Impact of Neon Injection on Electron Density Peaking in JET Hybrid Plasmas

Impact of low-mid Z impurity injection on plasma transport and confinement has been observed and reported in several Tokamak experiments. Understanding particle transport in mixed species plasmas is crucial for reactor relevant conditions where control of DT mixture along with control of He concentration will be necessary. In this paper we present the analysis of experimental electron density profile evolution in JET hybrid scenario discharges with increasing level of Neon seeding. The measured electron flux is compared with fully predictive transport simulations in search for the possible existence of a particle inward pinch proportional to the light impurity concentration as predicted by first principle gyro kinetic simulations. These seeding experiments, performed for power exhaust mitigation studies, offered the opportunity to study systematically the effect of Neon on density peaking and to compare it with theory predictions. The database includes hybrid discharges at IP = 1.4 MA, BT = 1.9 T, βN = 2.2, additionally heated by 16.5 MW of Neutral Beam Injection power (NBI). A few of the above discharges had a small amount (< 1 MW) of Ion Cyclotron Resonance Heating (ICRH). The current ramp-up, overshooting the plateau value was used to produce a central qo ≈ 1 broad low shear region for better confinement and NTM avoidance. Neon was injected at the start of the NBI heating phase and it was already present during the transition to H-mode: when the central density reached its top value (≈ 4 s later) the Neon contribution to the total number of injected electrons ranged from 5% to 40%. Un-seeded reference discharges were also performed with the same engineering parameters. In the seeded discharges, the core density profile peaking, defined as the ratio between the central (ρ=0.25) and the pedestal density, increases up to npeak/ped ≈ 2 depending on the amount of injected Neon. Interestingly, in this database, the density peaking did not increased with the average as previously described for un-seeded discharges. Fully predictive transport simulations, carried out with JETTO code proved that the introduction of an inward particle pinch proportional to the effective charge and the ion temperature gradient, as predicted by microturbulence theory, was needed to match the data.

Speaker: Dr Domenico Frigione (ENEA)

18.09.27-IAEA-summary-slide.pptx

111 Improvement of ITER equatorial EC launcher design for poloidal steering compatibility

This report describes the key development of the ITER equatorial ECH/ECCD launcher (EL) for poloidal steering compatibility. The steering direction of the EL has been changed from toroidal to poloidal in order to enhance the current drive capability. The design modification is being progressed toward the design finalization in 2019. The concept of upper launcher (UL) steering mechanism of steering-mirror assembly (SMA) is adapted for EL for poloidal steering. However, the redesign of the SMA for EL is needed and the key of the design is the torque balance between the bellows actuator, the coil springs and spiral pipe for mirror. Since the heat load of the steering mirror is larger than that of UL, the pipe diameter of the spiral-cooling water channel must be larger to provide more cooling water, which increases the torque of the spiral pipe. In order to compensate the increased torque, the design change of the coil spring is performed. Another of the redesign issues is the thermal stress at the Blanket Shield Module (BSM) for poloidal steering configuration. The thermal analysis shows the peak stress of the cooling channel is 820MPa, which exceeds the allowable stress limit (370MPa). By separating the first wall from the integrated shield structure, more cooling water channels can be routed close to the surface, which reduces the thermal stress of the cooling channel to around 300MPa. The mirror and waveguide unit are attached to the closure plate by rectangular flanges in the poloidal steering configuration. Because the surface pressure at the corner of the rectangular flange is high, it is impossible to keep homogeneous pressure to the rectangular vacuum seal. A simulation of the vacuum seal compression shows the necessary load for the bolts is 67.8kN, which exceeds the stainless steel bolt limit. In order to solve this problem, the introduction of the Inconel 718 bolt is considered. The 8 RF beams radiated from 8 waveguides are injected to the large parabolic steering mirror and focused to plasma. Therefore, injection angles of each beam are slightly different, which gives modified RF absorption profile compared to expected profile. In order to improve this situation, a ray tracing code is integrated with the EL optical system optimization program.

Speaker: Dr Ken Kajiwara (National Institutes for Quantum and Radiological Science and Technology)

FEC2018_summary_slide.pdf

112 In-Vessel Inspection System: Design progress of high vacuum and temperature compatible remote handling for fusion purposes

The plasma facing components (PFCs) in a tokamak are subjected to high heat flux and high temperature during plasma operation, which causes erosion of the first wall. There is also hot spot formation on the PFC due to physical phenomenon like thermal electron emission. In addition to fore-mentioned phenomenon, the events such as Edge Localized Mode (ELM), vertical displacement event (VDE) are serious concern for the fatigue damage of the PFCs. Therefore, health monitoring of the PFCs is an essential requirement in any tokamak, which is met by periodic inspection of the PFCs. The periodic inspection can be performed during the tokamak shutdown period or during plasma operation. The latter is most desirable as it allows quick and frequent in-service inspection of the PFCs between the plasma shots without breaking the vacuum. The work presented in this paper covers the conceptual design of In-Vessel Inspection System (IVIS) and storage chamber to carry out in-service visual inspection of SST-1 like tokamak under vacuum in between the plasma shots. The designed IVIS manipulator is ~2m long with 04- Degrees of Freedom (DOF), comprising of three rotary joints and one linear motion for deployment within the tokamak. The manipulator is designed to handle a cantilevered payload of ~1kg with a positional accuracy of <2mm. IVIS is initially stowed in a 4m long Ultra-High Vacuum (UHV) storage chamber isolated from the VV by an UHV gate valve. During (one quarter i.e. + 90°) viewing, the gate valve will open so that IVIS can be deployed inside the VV, complete the viewing procedure and return back to its initial position outside the VV. Issues like choices of the structural materials to minimize the out-gassing under vacuum and high temperature during conditioning are discussed with feasible solutions. Improvements to enhance IVIS operation under temperature and vacuum conditions for SST-1 like machine are reviewed. Results for theoretical calculations, kinematic and structural integrity analyses are presented in detail along with ways to optimize the design.

Speaker: Mr Manoahstephen Manuelraj (Institute for Plasma Research, Gandhinagar, Gujarat-382428, INDIA)

Summary_In Vessel Inspection System Design progress of high vacuum and temperature compatible remote handling for fusion purposes.pdf

113 Influence of Magnetic Field on Plasma Energy Transfer to Material Surfaces in ELM Simulation Experiments with QSPA-M

Features of plasma energy transfer to the material surfaces during the plasma-surface interaction in presence of strong magnetic field are investigated within recently developed quasi-stationary plasma accelerator QSPA-M. This novel PSI test-bed facility is able to reproduce the ELM impacts, both in terms of heat load and particle flux to the surface, and to provide plasma transportation in external magnetic field, which mimics the divertor conditions. Investigations of energy transfer to the material surface have been performed for varied plasma heat load and external magnetic field value. Calorimetry, optical emission spectroscopy and a high speed imaging were applied for PSI characterization. For perpendicular plasma incidence, it has been shown that the transient plasma layer is formed in front of the surface by stopped head of plasma stream even for rather small plasma heat loads, which not resulted in surface melting. The plasma density in this near- surface layer is much higher than in the impacting stream. It leads to the arisen screening effect for the energy transfer to the surface. For B=0, the thickness of screening layer is less than 2 cm, but it increases up to 10 cm when B= 0.8 T. Reducing the size of the target leads to growth of the fraction of plasma energy, which is absorbed by the surface. For plasma exposures of tilted target surfaces, the thickness of transient plasma layer is found to be essentially non-uniform. It is maximal for downstream part of the target while the upstream surface area remains completely unprotected. The impacting plasma shifts significantly the screening layer along the surface and also generates oblique shock wave from the protruding edge. This shock wave together with available shift of plasma layer along the target provides an additional shielding for the downstream part of the exposed surface. The important contribution of external magnetic fields to the plasma energy transfer to the material surfaces is also discussed. It has been found that presence of strong external magnetic field leads to decrease of the energy, which is transferred to the exposed surface, due to the growing plasma density in near- surface layer and its increasing thickness.

Speaker: Prof. Igor Garkusha (NSC KIPT)

114 Influence of neutral-plasma interactions on 3D scrape-off layer filaments

Filaments are field aligned, non-linear density perturbations, which have been observed in most plasmas. In tokamaks they can carry a significant amount of particles and heat from the last closed flux surface to the far scrape-off layer (SOL). This highly non diffusive transport mechanism can cause a significant heat load onto first wall materials. It is important to understand the motion of filaments, particularly in regard to the design of future fusion devices. Recent experiments on several machines have shown that the plasma density of the SOL can have a significant influence on the dynamics of filaments. We have carried out non-linear, 3D seeded filament simulations, with the focus on neutral-plasma interactions, using the BOUT++ library. The model is an extension of the STORM code, which is a two fluid model, including thermal electrons. In order to study the influence of neutrals, 1D background profiles are computed. By varying particle and heat influx, different profiles are generated. The filaments of critical size showed an increasing radial velocity with increasing upstream temperature, as expected from scaling laws. The filament further showed a decreasing radial velocity with increasing plasma density. In these conditions, the neutrals interaction resulted in a reduced radial velocity. It was further observed that the filaments radial velocity had a strong dependency on the target temperature, resulting in an increasing radial motion for an increasing target temperature. As higher neutral densities could affect the strong sheath currents, studying the neutrals filament interaction at higher densities is of interest. In the current study the density was further increased, as the previous simulations showed an increasing influence of the neutrals on the filaments with increasing background plasma density and temperature on the filament. The purely diffusive neutral model in STORM was extended to enable the modelling of higher density conditions towards detachment. This has been validated against other neutral simulation codes. This work has been carried out within the framework of the EUROfusion Consortium and has received funding from the Euratom research and training programme 2014-2018 under grant agreement No 633053.

Speaker: Mr David Schwörer (Dublin City University, Ireland)

summaryslides.pdf

115 Installation And Initial Run Of 96kV 7.2MW Acceleration Grid Power Supplies

Acceleration Grid Power Supplies (AGPS) provides 8MW power at (-) 96kV to the beam source of DNB (Diagnostic Neutral Beam) and SPIDER (Source for Production of Ion of Deuterium Extracted from Rf plasma) for acceleration of negative ions with specific modulation. High Voltage Power supplies (HVPS) based on PSM (Pulse Step Modulation) topology has already demonstrated its ability for broadcast transmitters, accelerators of RF source, neutral beam injectors. PSM based 96kV/75A AGPSs have been developed to feed the Acceleration Grid of Beam sources. Design redundancy ~15% allows for tolerating SPS modules failure without leaving the ongoing campaign. The AGPS is designed to turn off in a time much lower than 100 µs to minimize the energy (20 J) delivered to the arc in case of short circuit or breakdown. AGPS mainly composed of Multi-Secondary Transformers (3nos. 2.8MVA each), Switched Power Supply (SPS) Modules (150nos., 60kW each), FPGA/Real Time based controller and other auxiliaries including passive protection devices; factory tested in witness of IO. Novel, state of the art technologies for HV insulation such us multiple bushings integrated on large resin insulators and building feedthroughs have been developed. To ensure described functionalities a single AGPS is controlled by 9 powerful synchronous FPGAs managed by real time controller which support high performance requirement of PSM based HVPS like low ripple, high resolution, programmable rise time, fast dynamics, full depth modulation, fast switching off and fast (~few milliseconds) re-application in case of breakdowns. Deliveries of AGPSs are sequenced to allow early operational drills at ITER-India lab while other unit is being installed at NBTF site. Present article describes operational drills including protection functions, insulation test and specified behaviour of AGPS on dummy load at ITER-India lab. This allows for offering DNB-AGPS for extended Factory acceptance testing.

Speaker: Mr Narinder Pal Singh (Institute for Plasma Research)

Summary AGPS NPsingh.pdf

116 Integrated modelling of core and divertor plasmas for DEMO-FNS hybrid facility

The steady state regime for tokamak based neutron source DEMO-FNS with parameters R/a=3.2 m/1m, B=5Т, Ip=4-5 MA, PNBI=30MW and РECR=6МW is studied using a consistent modeling of the central and divertor plasma. In our formulation, the divertor plasma state is determined by the values of heat flux PSOL and the pressure of the neutrals in the divertor pn. As boundary conditions for the central plasma we use values of density and temperatures of ions and electrons on the separatrix and the neutral flux through the separatrix toward to the central plasma column. In divertor region all values calculated by the program SOLPS4.3 for a set of operating points (~30 in our case) with different values of PSOL and pn, and then the calculation results are approximated by analytical formulas. Heat transport in the central plasma is calculated using the ASTRA code and sets the scaling for the confinement time of energy IPB(y,2) with variation of H-factor. The simplified physical model for the description of the pedestal in H-mode inside the separatrix is used, based on the scalings for width and pressure at the pedestal. The density of the plasma (electrons or ions of deuterium and tritium) is modelled taking into account sources of neutrals coming from divertor region, as well as the injection of fast atoms and/or pellet injection. The neon injection is modeled to reduce the heat loads to divertor plates, that would able to radiate up to 60% of input power. The Helium plasma dilution is taken into account to estimate the maximum permissible helium confinement values. The simulation determines the window of plasma parameters DEMO-TIN, in which the heat load on divertor plates remain at an acceptable level, and the divertor plasma does not go into “detachment” mode. The dependence of these conditions on the radiation power, the impurity level, fraction of alpha-particles is investigated.

Speaker: Dr Alexey Dnestrovskiy (NRC Kurchatov institute)

summary_slide_.pptx

117 Isotope Dependence of Confinement in JET Deuterium and Hydrogen Plasmas

Heat, particle and momentum confinement in L- and H-mode in deuterium (D), hydrogen (H) and in D/H mixtures have been investigated in JET. In L-mode (3T/2.5MA) at fixed density (2.5x10^19m^-3) a weak positive scaling of stored energy with ion mass, tau_Eth~A^0.15, is found [1], consistently with multi-machine scaling tau_Eth~A^0.2 [2]. Core temperature profiles are stiff with Ti~Te, and R/LTe~8 at mid-radius [1]. Flux-driven core transport modelling with TGLF show ITG’s to be dominant and predict no isotope scaling as a result of the Ti profile stiffness. A fuelling rate ~30%, higher in H than in D, was necessary to achieve the same density as in D, indicating a difference in particle confinement which was confirmed by EDGE2D/EIRENE simulations near the LCFS [1]. In type I ELMy H-mode (1T/1MA, 1.7T/1.4MA and 1.7T/1.7MA, Paux in the range 3 to 17MW) it was not possible, except in a couple of cases, to establish the same densities in H as in D, despite gas fuelling rates several times higher in H, showing a strong reduction of particle confinement. The best regression for the thermal stored energy for ELMy H-mode is obtained as W_Eth ∝ A^0.38 P^0.64 Ip^0.89 n^0.5 G^0.21 where A is the ion mass and G the fuelling rate. The mass scaling is twice that of IPB98(y,2). GENE gyrokinetic calculations in H-modes show ITG’s to be dominant in both species. The observed negative dependence of momentum confinement on the gas fuelling rate suggests that edge fuelling leads to a direct deterioration of ion heat transport. Dimensionless identity experiments for H and D pairs provided good matches for the kinetic profiles in L-mode, but not in H-mode. In H-mode the scaled confinement time in D was 30% higher than in hydrogen for the best approximate match. The evidence from these experiments suggests that the isotope scaling in these experiments, as well as the absence of good dimensionless matches in H-mode, have their origin in the pedestal and boundary region, which are sensitive to atomic physics, fuelling and recycling. [1] C.F. Maggi et al, Plasma Physics and Controlled Fusion 60 (2018) 014045 [2] ITER Physics Basis, Nuclear Fusion 39 (1999) 2175

Speaker: Mr Henri Weisen (SPC EPFL)

IAEA_isotope_8p_corrected.pdf

Summary_slide.pptx

118 Machine Control System for Large Volume Plasma Device: Current Status and Future Directions

The Large Volume Plasma Device (LVPD) [1] is a cylindrical shaped pulsed plasma device dedicated in carrying investigations relevant to fusion and magneto-spheric plasma. For meeting requirements for its up gradation, efforts are in progress towards enhancing plasma duration (tpulse ~9-50ms), to cater need of controlled experiments on Electron Temperature Gradient(ETG) turbulence, a major source of plasma loss in fusion devices by suitably varying the density gradient scale length. The Machine control system (MCS) has the responsibility of protected and integrated operation of the device using standardized interface. MCS consists of namely, 1) PXIe based data acquisition system [2], 2) Modbus based process automation system [3.4] and 3) RAID configured based data handling system. The PXIe based data acquisition system is already implemented and its upgradation for data processing to convert raw signals of various diagnostics to plasma parameters and up gradation of hardware for non-linear structure study are underway.The Modbus bus has been selected for process automation of the device. Currently, process automation has been carried out for high current filament power supply and radially movable probe positioning system (~ 12 numbers). The efforts are going on for extension of the automation for 3-axis probe drive system, camera based surveillance system, axial probe positioning, vacuum production system and different power supplies. A RAID configured server is under procurement for hosting MDS+ based data handling system. The LabVIEW has been selected as supervisory data acquisition and control system for development.The novelty of the work lies in integration and handling of heterogeneous I&C controllers under single console. The paper will discuss the results obtained for integration and operation of machine control system. References: 1. S. K. Mattoo, S. K. Singh, L. M. Awasthi, et al., Physical Rev. Lett.108, 255007(2012). 2. R. Sugandhi, P. K. Srivatava, Prabhakar Srivastav, et al., 7th Int. Conference on Cloud Computing, Data Science and Engineering, IEEE conference series, 804(2017). 3. R. Sugandhi, P. K. Srivastava, A. K. Sanyasi, et al., Fusion Engineering and Design 112, 804 (2016). 4. R. Sugandhi, P. K. Srivastava, A. K. Sanyasi, et al., Fusion Engineering and Design 115, 49(2017).

Speaker: Mr Ritesh SUGANDHI (Institute for Plasma Research, Gandhiangar, India)

summary_slide_fip_p1_25.pdf

119 Minimising power load asymmetries during disruption mitigation at JET

The high thermal loads caused by a disruption of an ITER baseline scenario pulse potentially stored thermal energy of 350MJ and magnetic energy inside the vessel of 400 MJ pose a severe threat to the first wall components [1]. Massive gas injection (MGI) into a disrupting plasma has been shown to be capable of reducing the energy deposited onto the plasma facing components by increasing the radiation. However, the uneven distribution of the radiated power following a single local massive gas injection leads to highly localised radiation and hence to significant thermal loads due to the radiation “flash” [2]. In addition, the presence of the n=1 mode during the disruption produces toroidal and poloidal radiation asymmetries. Depending on the phase relationship between the n=1 mode and the MGI-location, this effect can be enhanced or diminished. In order to address this issue, JET has installed three MGI-valves at poloidal and toroidal positions similar to ITER. Single or a combination of two MGI-valves have been fired into a locked error field mode, whose toroidal O-point position was imposed by applying an external n=1 magnetic perturbation field. By measuring the radiated power at two separate toroidal locations and varying the toroidal phase of the perturbation field a toroidal peaking factor TPF, defined as the ratio of the maximum radiation to the average value, could be estimated. For a single injection TPFs in the range of 1.5 up to 1.8 have been found, depending on the type of impurity gas used. Optimising the time delay between two MGI-valves, which are toroidally at opposite locations, allowed a reduction of the TPF down to 1.2. The measured radiated power asymmetries are sensitive to small variations of the delay between the two MGI valve triggering times in the order of less than a millisecond. In this contribution the experimental findings of radiation asymmetries during mitigated disruptions caused by a seeded error field mode and the comparison with a heuristic model will be presented and the implications for the ITER disruption mitigation system discussed. [1] M. Lehnen et al., Journ. Nucl. Mat. 463 (2015), 39. [2] R. Pitts et al., Journ. Nucl. Mat. 463 (2015), 748.

Speaker: Mr Stefan Jachmich (BeLPP)

IAEA2018_summary_slide.pptx

120 New results in stellarator optimisation

The ROSE code was written for the optimisation of stellarator equilibria. It uses VMEC for the equilibrium calculation and several different optimising algorithms for adjusting the boundary coefficients of the plasma. Some of the most importand capabilities include optimisation for simple coils, the ability to simultaneously optimise vacuum and finite beta field, direct analysis of particle drift orbits and direct shaping of the magnetic field structure. ROSE was used to optimise quasi-isodynamic, quasi-axially symmetric and quasi-helically symmetric stellarator configurations.

Speaker: Dr Michael Drevlak (Max-Planck-Institut für Plasmaphysik)

121 Nuclear Performance Analysis and Optimization Study of Indian Solid Breeder Blanket for DEMO

The tritium breeding blanket is the essential part of a fusion reactor which provides the tritium fuel self-sufficiency to the reactor. India under its breeding blanket R&D program for DEMO is focusing on the development of two breeding blanket concepts viz. Lead–Lithium cooled Ceramic Breeder (LLCB) and Helium Cooled Ceramic Breeder (HCCB). The study presented in this paper focuses on the neutronic design analysis and optimization of HCCB blanket which is having an edge on configuration and is one of the variants of helium cooled solid breeder blanket concepts proposed by several other countries. Indian HCCB blanket aims at utilizing the low energy neutrons at the rear part of the blanket and has RAFMS as the structural material, Lithium Titanate (Li2TiO3) as tritium breeder with Beryllium (Be) as neutron multiplier. The aim of the optimization is to minimize the radial blanket thickness, while ensuring tritium self-sufficiency and provide data for further neutronic design and thermal-hydraulic layout of HCCB blanket. Several parametric studies have been performed considering, different 6Li enrichment, varying composition of Be & Li2TiO3 in the breeder blanket and radial length of the breeder zone, as well as different arrangements of Be & Li2TiO3 layers in the blanket. The cases provided tritium self-sufficiency and sufficient shielding of the TF-coils have been identified. Neutronic calculations are performed using the 1-D discrete ordinate code ANISN with FENDL-2.1 nuclear cross section data library to assess the overall nuclear performance of HCSB blanket. The inboard and outboard blanket thicknesses of 40 cm and 60 cm respectively can give TBR > 1.3, with 60% 6Li enrichment which is assumed to be sufficient to cover potential tritium losses and uncertainties. It is found that optimal multiplier to breeder material volume fraction ratio obtained is around 3:1. The results also demonstrated that Be packing fraction has more profound impact on the TBR as compared 6Li enrichment and packing fraction of Li2TiO3. Other improvements on the TBR are seen by introducing a 10 mm breeder layer before multiplier layer behind the first wall.

Speaker: Mr Deepak Aggarwal (Institute for Plasma Research)

122 Numerical Diagnostic to Investigate Poloidal Asymmetry in Three-Dimensional Magnetic Configurations

Some experimental observations show poloidal asymmetry in the turbulence measurements, which can affect the plasma transport, so detailed spatial structures must be clarified. In Large Helical Device (LHD), an up-down asymmetry has been observed by the PCI diagnostic. Complicated configurations make it difficult to capture the entire structures of fluctuations in helical plasmas, so three-dimensional (3-D) turbulence simulations are necessary for understanding the mechanism. We are developing the Turbulence Diagnostic Simulator (TDS), and carry out the numerical diagnostics in helical plasmas for understanding the plasma turbulence. In this case, the gyrokinetic simulation code GKV-X provides turbulent fluctuations in 3-D configurations, and then, the TDS calculates its line-integration along the line of sight (LS) as in phase contrast imaging (PCI) to give numerical observation signals. There is a problem to resolve the local values from the line-integrated signal. The pitch angle of the magnetic field is used to help the identification of the local spectrum. A finite resolution in the local wavenumber spectrum deteriorates the reconstruction. The ITG modes have a characteristic wavelength and frequency, and difference in the spectrum can be distinguished at different radial positions, considering the spatial resolution. Characteristics of turbulence can be estimated by this analysis. The results of the TDS application indicate three factors to induce the poloidal asymmetry; 3-D magnetic configuration with the realistic LS, effect of signal processing techniques, and inherent inhomogeneity of the turbulence itself. The original data includes only small up-down asymmetry, because this is given from a single flux-tube data. The effect from the 3-D configuration generates the asymmetry, and tends to be enhanced by signal processing, but is not comparable with the experimental results. Artificial reduction of the fluctuation amplitude in the bottom half of the region can give the comparable asymmetry. This result indicates an inherent asymmetry of the turbulence. This asymmetry may be attributed to the dependence on the field line label, which is being confirmed by the GKV-X code.

Speaker: Dr Naohiro Kasuya (Kyushu University)

THP1-2kasuya_summary.pptx

123 On the role of radial electric fields on turbulence spreading in the plasma boundary of fusion devices

Turbulence spreading is the transfer of free turbulent energy from strongly driven (i.e., unstable regions) to weakly driven locations [1]. The net effect of this phenomenon is the radial redistribution of turbulent energy, modifying local plasma features. It has been pointed out that spreading may be important in setting the Scrape-Off Layer (SOL) width. The peak heat load onto the divertor is intimately related to the SOL width, and the understanding of the mechanisms setting this width is fundamental for a reliable prediction of the SOL decay length for ITER. In this work, we report on measurements of turbulence drive and turbulent spreading, as defined by Manz, P. et al [2], from the near edge to the far SOL region of TJ-II. A 2-D Langmuir probe array [3] was used to measure both parameters as well as the profiles of floating potential, plasma density, radial turbulent particle flux, effective radial velocity, potential turbulence correlation time and phase velocity of the fluctuations. The radial electric field in the edge was modified by a biasing electrode, inserted into the edge of the plasma ($\rho \approx 0.85$), delivering a voltage $\pm$ 350 V (with respect to the wall), with a square 40 Hz waveform. All the parameters were modulated by the biasing. At -350 V, the velocity shear reached its maximum, resulting in a strong suppression of turbulent transport and the effective radial velocity fluctuations, not only at the shear layer, but also in the far SOL. Moreover, the ion saturation profile steepened at the shear layer location and was reduced in the SOL. The local turbulence drive and turbulence spreading were also impacted by the biasing. The driving term was strongly reduced in the shear layer, and only slightly reduced in the SOL. Turbulence spreading was mainly modified in the SOL when the $E_r\times B$ shear reached values close to the inverse of the turbulence correlation time in the vicinity of the Last Close Flux Surface (LCFS). In summary, biasing was found to reduce edge-SOL coupling by decreasing turbulence spreading, thus affecting the ion saturation current profile, which may have an impact on the SOL width. [1] X. Garbet et al., Nucl. Fusion 34 (1994) 963. [2] P. Manz P. et al., Phys. Plasmas 22 (2015) 022308. [3] J. Alonso. et al., Nucl. Fusion 52 (2012) 063010.

Speaker: Dr Carlos Hidalgo (CIEMAT)

TS_Slide.pptx

124 Overview of disruptions with JET-ILW

This paper presents an analysis of disruptions occurring during JET-ILW plasma operations covering the period from #80128 up to #92504. The total number of disruptions was 1951 including 466 MGI (massive gas injection), VDE (vertical displacement event) and Error Field Correction Coil experiments, which led to intentional disruptions; hence the average disruption rate is 16.1%. MGI has been routinely used in protection mode both to terminate pulses when the plasma is at risk of disruption, and to mitigate against disruptions, in total 896 shots were ended by MGI. The subset of 913 natural disruptions, which were not affected by special dedicated experiments or MGI protection, was used for analysis of pre-disruptive plasma behaviour. The pre-disruptive plasma parameters of the natural disruptions are Ip=(0.82-3.14)MA, toroidal field Bt=(0.98-3.36)T, q95=(1.52-9.05), li=(0.58-1.86), betap=(0-1.1), volume average plasma density n_e=(0.2-8.5)10^19 m^-3, X-point (317 shots) and limiter (596 shots) configurations. Apart from 21 exceptional cases, the MGI was triggered by n=1 locked mode (523 shots) or by the disruption itself, specifically by dIp/dt (207 shots) or by toroidal loop voltage (145 shots). On JET only the locked mode was treated as either a precursor or the cause of disruptions. However, long lasting locked modes (≥100ms) do exist prior to disruption in 75% of cases. Though, 10% of non-disruptive pulses have a locked mode which eventually vanished without disruption. The plasma current quench (CQ) may result in 3D equilibria, termed as asymmetrical disruptions, which are accompanied by sideways forces. Unmitigated VDEs generally have significant plasma current toroidal asymmetries. The unmitigated disruptions also have large plasma current asymmetries presumably because there is no plasma vertical position control during CQ. However, MGI is a reliable tool to mitigate 3D effects and accordingly sideways forces. The vessel structure loads depend on the force impulse and force time behaviour or rotation. The toroidal rotation of 3D equilibria is of particular concern because of potential resonance with the natural frequencies of the vessel components in large tokamaks such as ITER. The amplitude-frequency interdependence is important, since a simultaneous increase of amplitude and frequency would potentially create the most challenging load conditions.

Speaker: Dr Sergei Gerasimov (CCFE)

EX_P1-24-summary-slide_V1.pptx

125 Overview of ITPA R&D Activities in Support of ITER Diagnostics

The International Tokamak Physics Activity (ITPA) Topical Group (TG) on Diagnostics has been conducting R&D activities to support improved ITER diagnostic performance. In this paper, highlights of the Topical Group activity are overviewed: mitigation of first mirror degradation in optical systems, mirror cleaning techniques have been progressed; in-vessel stray-light has been investigated to reduce its impact on diagnostics; diagnostics of escaping particles, feasibility test of the activation probe technique has progressed under a multi machine joint experiment. Diagnostic systems are essential for machine protection, reliable machine operation and comprehensive understanding of burning plasma behavior in ITER [1]. In order to achieve the above aims, more than fifty sub-systems will be developed for measurement of plasma and plasma facing components in the harsh ITER environment, e.g. higher neutron/ -ray irradiation and lower accessibility/maintainability compared to that of existing fusion devices. ITPA Diagnostics TG has addressed common physics issues in diagnostics development [2]. The TG activity is mainly directed to High Priority research areas (HP); HP-1: Optimization of the life-time of plasma facing mirrors used in optical systems, HP-2: Assessment of impact of in-vessel wall reflections on diagnostic systems, HP-3: Develop methods of measuring the energy and density distribution of escaping alphas HP-4: Plasma control system measurement requirements HP-5: Develop diagnostic calibration techniques/strategies compatible with the burning plasma environment and Joint Experiments for Diagnostics (JEX-DIAG) under a framework between ITPA and the Implementing Agreement on Co-Operation of Tokamak Programs of the International Energy Agency (IEA); JEX-DIAG-2: Environmental tests on first mirrors, JEX-DIAG-5: Field test of an activation probe, JEX-DIAG-6: Cross comparisons of Charge Exchange Recombination Spectroscopy and X-Ray Imaging Crystal Spectroscopy, JEX-DIAG-7: Distributed monitoring of microwave power density, JEX-DIAG-8: Benchmark of Wall reflections, JEX-DIAG-9: Spectral MSE (MSE-LS) experiments as design driver for ITER JEX-DIAG-10: Minimizing microwave absorption in vacuum windows JEX-DIAG-11: Determination of the runaway electron distribution function by spectral Bremsstrahlung measurements in the gamma-ray energy range.

Speaker: Dr David Brower (University of California Los Angeles)

126 Performance Evaluation of 1.3 kW at 4.5 K Helium Refrigerator/ Liquefier (HRL) at IPR

At IPR, 1350 W at 4.5 K helium cryo plant is dedicated to facilitate the cooling requirements of SST-1 machine. Since 2004, helium refrigerator / liquefier (HRL) (Make: M/s. Air Liquide, France) is operational in mixed mode equivalent to 650 W (refrigeration power) and 200 lh-1 (liquefaction capacity) at 4.5 K. The HRL can be operated in two phase (1.3 – 1.5 bar (a) at 4.5 K – 4.7 K) as well as single phase supercritical helium (at 4 bar (a) and 4.5 K with nominal mass flow rate of 300 gs-1 ) modes of operation. The refrigeration capacity of the HRL is 650 W at 4.5 K used to make TF and PF coils superconducting whereas the remaining capacity of 200 lh-1 is utilized for powering the vapor cooled current leads system of SST-1 at rated current of 10 kA. To ensure the availability of the HRL and its best performance as per the needs of long duration SST-1 experiments, we carry out preventive maintenance of the different cryogenic components and subsystems as per defined schedule. These activities result in increasing the life span of the HRL as well as ensure its maximum availability during SST-1 operation. M/s. Air Liquide envisaged to carry out every five years preventive maintenance of the HRL for all the sub-systems and components. After major maintenance, it is desirable to have performance test on the HRL. We have carried out major preventive maintenance of the HRL and measure the HRL capacity during 2009-2010. Recently, we have further carried out the maintenance ourselves and carried out the performance test. The equivalent cold power of HRL found to be 1160 W (in pure refrigeration mode), 10.7 gs-1 (in pure liquefaction mode) and 1300 W equivalent (in mixed mode) at 4.5 K. These values matches with our last experimental measurements during HRL maintenance performed in 2010 and as expected considering the operational hours of HRL after thirteen years of operation. These results are quite satisfactory from the HRL performance point of view. The HRL capacity strictly depends on the different modes of operations. In this paper, we report the performance evaluation of cold capacity of HRL at IPR since it commissioning to till date.

Speaker: Mr Rohitkumar Panchal (Institute for Plasma Research)

FEC2018_Rohit Panchal_Summary slide.pdf

127 Performance of the plasma source and heating concept for the Prototype-Material Plasma Exposure eXperiment (Proto-MPEX)

The Material Plasma Exposure eXperiment (MPEX) is a planned linear plasma device to address plasma-material interactions for future fusion reactors. Its concept does foresee the capability to expose apriori neutron irradiated material samples to fusion reactor grade divertor plasmas. This new capability will be unique world-wide addressing important research needs in the area of fusion nuclear science. It will be an evolution to current operating steady-state linear plasma devices, which are limited either in plasma fluxes they can deliver to the material targets or plasma temperatures (for ions and electrons) they can reach in front of the material targets. The concept of MPEX does foresee a combination of a high-power helicon plasma source with microwave electron heating and ion cyclotron resonance heating. This source and heating concept is being tested on the Prototype-Material Plasma Exposure eXperiment (Proto-MPEX). With 100 kW helicon power a plasma density of 8e19 m-3 was achieved, which is about a factor 2 more than required for MPEX. Electon heating was pursued with a 28 GHz gyrotron. A maximum power of 50 kW was delivered to the plasma, which is produced by the helicon. At this frequency, the plasma is overdense in the plasma center (> 1e19 m-3). Maximum electron temperatures of 20 eV have been achieved under those overdense plasma conditions with Electron Bernstein Wave EBW) heating. This is almost the electron temperature required for MPEX (25-30 eV). Ion cyclotron heating (ICH) was performed in the frequency range of 6 - 12 MHz with a low power ICH antenna able to launch about 25-30 kW of power. Without ICH, the ion temperature is about 2-4 eV. With ICH ion temperatures of 8-12 eV were measured. The ion fluxes to the target are about 5e23 m-2s-1. The plasmas produced by the helicon antenna have been modeled extensively with a fluid plasma code, coupled to a Monte-Carlo neutral code (B2-Eirene). The plasma transport can be well explained by this fluid approach and a radial diffusion coefficient consistent with Bohm-like transport. The transport of auxiliary heated plasmas (ECH/EBW and ICH) is currently being investigated and experimental results of this investigation will be presented.

Speaker: Dr Juergen Rapp (Oak Ridge National Laboratory)

JRapp_IAEA18_paper_v1.pdf

128 Plasma and diagnostics preparation for alpha-particle studies in JET DT

A deuterium-tritium (D-T) experimental campaign DTE2 on JET scheduled for 2019-2020,will be done in the Be/W vessel and will address essential operational, technical, diagnostic and scientific issues in support of ITER [1]. In preparation for the campaign, developments were performed on JET aiming at studies of alpha-particles. For studying AEs driven entirely by alpha-particles, a scenario similar to the TFTR beam “afterglow” [2] was developed for JET. In DT plasmas, after NBI is switched off, alpha-particles will be the only energetic ions during time interval between slowing-down times for NBI-produced ions and alpha-particles. Detection of alpha-driven AEs in this time window may help in diagnosing the temporal evolution of the pressure profile and slowing-down time of alpha-particles. JET advanced tokamak scenarios with q ≈ 1.5-2.5 were chosen and discharges have been successfully developed. The transport modelling extrapolated to DT predicted that alpha-particle beta of ≈ 0.1% could be achieved comparable to that in successful TFTR experiments. In “hybrid” scenario plasmas with q0 ≥ 1, fast ion losses in the MeV energy range were observed during n=1 fishbones driven by a resonant interaction with D beam ions in the energy range ≤ 120 keV [3]. The losses are identified as an expulsion of D-D fusion products, 1 MeV tritons and 3 MeV protons. A mode analysis with the MISHKA code combined with the study of nonlinear wave-particle interaction with HAGIS show that the loss of toroidal symmetry strongly affects the confinement of high energy tritons and protons by perturbing their orbits and expelling them in a good agreement with experiment. The extrapolation to the case of alpha-particles in DTE2 hybrid scenarios with similar fishbones has shown an additional alpha-particle loss of ~ 1% [3]. References: [1] Weisen H et al., Fus. React. Diag., AIP Conf. Proc. 1612, 77-86 (2014); [2] Nazikian R et al., PRL 78, 2976 (1997); [3] Fitzgerald M et al, submitted to Nucl. Fusion (2018).

Speaker: Dr Sergei Sharapov (CCFE)

Sharapov-summary-slide.pdf

129 Plasma--surface related three-dimensional modeling results for Wendelstein 7-X and EAST

Present-day fusion devices are operated with a multitude of diagnostics in different locations, with which important insight in plasma profiles is obtained. However, since the detected signals only represent a spatially small part of the machine, the experiment natively exhibits blind spots, in particular in the three dimensional edge plasma region, where flux surface averaging reductions are inappropriate. Theory, and especially numerical simulation, may bridge over these unknown areas in order to complete the complex physical picture of the nature of the plasma profile. The fluid plasma edge Monte-Carlo code (EMC3) [1] coupled to the kinetic (neutral) transport code EIRENE [2,3] is a commonly used fully dimensional plasma edge simulation code for treating such complex magnetic configurations. EMC3 bases on a Monte-Carlo algorithm for a reduced set of Braginskii equations formulated in a Fokker-Planck scheme, while EIRENE solves extended Boltzmann equations in full phase-space directly. Because of its intrinsically 3D structure, one of the main applications of EMC3-EIRENE is the simulation of scrape-off layer physics for the stellarator Wendelstein 7-X. However, also in tokamaks 3D effects may play an important role, e.g. when using resonant magnetic perturbations to suppress the formation of ELMs. With this contribution, we present recent results obtained with EMC3-EIRENE. After the study of the divertor manipulator concept and design [4], we stress the importance of kinetic treatment of certain minority ions at the example of helium operation in Wendelstein 7-X [5]. Subsequently, we apply the 3D resolved virtual diagnostics module of EIRENE, capable of simulating a fully synthetic helium beam diagnostic and present results on effective charge state distribution modeling. The same computational tools are then applied to intrinsically 3D Lower-Hybrid Wave induced magnetic perturbation modeling on EAST. We close with a discussion and outlook of the physical impact the enhanced kinetic ion transport description in EIRENE has on both, stellarator and tokamak simulations. [1] Y. Feng et al., J. Nucl. Mater, 266-269, 812 (1999) [2] http://www.eirene.de on 2nd Feb 2018 [3] D. Reiter et al., Fusion Sci. Technol, 47 (2), 172 (2005) [4] M. Rack et al., Plasma Sci. Technol, accepted (2018) [5] M. Rack et al., Nucl. Fus. 57, 056011 (2017)

Speaker: Dr Friedrich Schluck (DeFJ)

summary_slide_iaea_fschluck.pdf

130 Predict-First Analysis and Experimental Validation of MHD Equilibrium, Stability, and Plasma Response to 3D Magnetic Perturbations

An integrated-modeling workflow has been developed to predict equilibria and response to 3D magnetic perturbations in tokamak experiments. Starting from an equilibrium reconstruction from a past experiment, the workflow couples together the EFIT Grad-Shafranov solver, EPED model for pedestal stability, and NEO drift-kinetic-equation solver (for bootstrap current calculations) in order to generate equilibria with self-consistent pedestal structures as the plasma shape and various scalar parameters (e.g., normalized beta, pedestal density, $q_{95}$) are changed. These equilibria are then analyzed using automated M3D-C1 to compute the MHD plasma response to 3D magnetic perturbations. The workflow was created in conjunction with a DIII-D experiment studying the effect of triangularity on plasma response, showing excellent agreement between the analysis of the workflow's equilibria and equilibria reconstructed from the experiment. Various versions of the workflow demonstrated that the details of the edge current profile were not important for these cases, while $q_{95}$ and the details of the global pressure profile had a significant impact on the results. A predict-first study was then carried out for a DIII-D experiment examining how plasma response varies between single- and double-null shapes. The predicted equilibria were used to guide experimental planning and the predicted response was found to agree well with the perturbed magnetic field measured on the high-field-side midplane. Applications of this workflow to KSTAR and EAST experiments will also be explored. This work forms the basis of predictive scenario development across current and future devices (e.g., ITER), allowing for higher-fidelity predictions of MHD stability and 3D plasma response. Work supported by the US DOE under DE-FG02-95ER54309 and DE-FC02-04ER54698, along with NFRI, South Korea.

Speaker: Dr Brendan Lyons (General Atomics)

Lyons_IAEA_summary_v2.pdf

Lyons_IAEA_summary_v2.pptx

131 Preliminary Design of IN-DA Diagnostic Plant Instrumentation & Control

In ITER, plant Instrumentation & Control (I&C) components are exposed to harsh environment. Hence I&C for plant system is one of the most challenging requirements to fulfil the ITER demands. IN DA is responsible for the delivery of several diagnostics systems including (1) X-Ray Crystal Spectroscopy (XRCS) edge & survey to measure the plasma impurity for machine protection and basic control as well as well measure the profile of plasma parameters for advanced control. (2). Electron Cyclotron Emission (ECE) – to provide temperature profile, fluctuation and the power due to emission in 70 -1000 GHz for ITER plasma and (3). UP#09 for housing the diagnostics in the port plug and integration with rest of its system. (4) CXRS-pedestal – to provide the ion velocity and temperature of plasma for advanced control & physics studies. Out of these the XRCS diagnostics and UP#09 are classified as protection important components (PIC) and hence need special attention to achieve safety functions. ITER plant I&C systems are being developed according to industrial systems engineering standards, and compliant with the standards, specifications and interfaces defined in the Plant Control Design Handbook (PCDH) and its satellite documents. Enterprise Architect (EA) is the tool is to be used for diagnostic I&C documentation. EA helps to trace high-level specifications for the analysis, design, implementation, test and maintenance models using Unified Modelling Language (UML), SysML and other open standards. I&C deliverable documents are being developed according to the ITER diagnostic guidelines. This paper describes the detailed preliminary design of plant I&C for diagnostics system a) Operation procedures, b) functional analysis including variable definition, c) hardware architecture and signal d) cubicle configuration and e) the plant system operating state machine (PSOS) for automation including the mapping to Common Operation States (COS).

Speaker: Mr SHIVAKANT JHA (ITER-INDIA, IPR)

Summary slide.pdf

132 Preliminary development on a conceptual first wall for DEMO

For a DEMO reactor, the first candidate material for plasma facing material(PFM) is tungsten(W) and current available structure material is reduced activation ferritic/martensitic (RAFM). And tungsten coating material is promising to be applied on first wall. Since chemical vapor deposition tungsten (CVD-W) has a higher density, less porosity and better thermal shock resistance, thick CVD-W coating is used as the plasma facing material here. Southwestern Institute of Physics (SWIP) has developed a new RAFM material, which is called CLF-1. The new conceptual first wall for DEMO in this work is designed and developed with CVD-W and CLF-1. Due to different thermal expansion coefficients of tungsten and steel, CVD-W will detach from CLF-1 steel under heat load and plasma exposure if it is coated onto the CLF-1 directly. As a result, an interlayer must be applied to mitigate the stress between CVD-W and CLF-1. Furthermore, the tungsten will generate cracks under steady state and transient heat loads in reactors and crack in the tungsten will make tritium to penetrate into the substrate rapidly. Tritium accumulation is a critical parameter for reactors which is very important for safety and steady state operations. The new conceptual first wall consists of CVD-W, CLF-1 and an interlayer between them. The interlayer is required to have good bonding property and tritium prevention, which is crucial for controlling the inventory buildup and maximizing the fuel efficiency. SiC and TiN applied as the interlayer between W and CLF-1 in the first wall are investigated. In order to figure out the influence of fabrication technology, layer thickness and coating rate, a series of material samples are fabricated and tested. The SiC interlayer on the CLF-1 substrate is made by three means of coating technologies including physical vapor deposition (PVD), chemical vapor deposition (CVD) and Chemical Vapor Infiltration (CVI) while TiN interlayer is obtained by CVD. On the top of the interlayer SiC or TiN, a CVD-W layer with the thickness of 1mm is coated with the rate of 0.5mm/h at the temperature of 450-550 oC. The material analysis and mechanical tests on those samples present that SiC by CVI and TiN by CVD and TiN by CVD have sufficient adhesiveness as an interlayer between W and CLF-1, which show good bonding property and no obvious detachment or delamination is found.

Speaker: Dr Laizhong Cai (Southwestern Institute of Physics)

Summary of IAEA paper.pdf

133 Preliminary Pipe Stress Analysis of High Pressure, High Temperature Experimental Helium Cooling System

Experimental Helium Cooling Loop (EHCL) is a high pressure-high temperature helium gas system. EHCL is similar to the First Wall Helium Cooling System (FWHCS) of LLCB TBM and in this loop First wall mock ups up to one fourth (¼) size of TBM can be tested. EHCL modelling consists of equipment arrangement, pipe routing, support, cable tray routing, instrumentation arrangement and tube routing. EHCL lab floor dimensions are 18m x 18m length and width respectively while the vertical height is 5 meter. The lab is divided in three major areas: process area, control room and free space for maintenance activities. The process and control room covers 9m x 9m and 14m x 5m floor area respectively. The EHCL is designed to operate with helium gas at 8.0 MPa (gauge) pressure and at 300-400 C temperature. The flow rate varies from 0.2 kg/s to 0.4 kg/s. The selected size for the connection pipes is DN 50. The high temperature pipes in this loop are at 400 C and at 8 MPa pressure, and these pipes are connected to equipment in a limited space. The detailed flexibility analysis was carried out, to ensure safety of the piping system and to maintain the structural integrity under loading conditions (both external and internal), which may occur during the lifetime of the system. SS 316L is used as structural material for piping and equipment. This poster presents the modelling of EHCL and the results of detailed flexibility analysis of EHCL pipes. To carry out the analysis, the entire piping system of the loop was modeled and the static and dynamic analysis was carried out in CAESAR II software. For the floor response spectra, the floor level in two horizontal and one vertical direction was computed. As IPR lies in seismic zone –III, and the process loop is planned to be located at ground level at IPR campus, accordingly the FRS was used to find out the induced stress in the process loop. The dynamic effect and weight effects are considered in the design so that the stresses created by the combined loads do not exceed the allowable stresses prescribed by the design codes. Finally the piping layout satisfying the code requirements along with the results are presented in the poster.

Speaker: Mr Aditya Kumar Verma (Institute For Plasma Research)

Summary Slide.pptx

134 Preliminary results of prototype Martin-Puplett Interferometer and transmission line developed for ITER ECE Diagnostic

The ECE Diagnostic system in ITER will be used to determine the electron temperature profile evolution, the high frequency fluctuation of the plasma electron temperature, the characterization of runaway electrons and the radiated power in the electron cyclotron frequency range (70-1000 GHz). These measurements will be used for advanced real time plasma control (e.g. steering the electron cyclotron heating beams) and the ITER plasma physics studies. In view of the ITER requirements, an ultra-wide band (70 – 1000 GHz) transmission line coupled to a fast scanning, broadband spectrometer are required to estimate the ECE radiated power loss and to study the behavior of runway electrons. Typically, the transmission lines and spectrometers are not operated in vacuum and there are consequently significant losses at certain frequencies due to water vapor line absorption over this large frequency range. To avoid these losses, both the transmission line and the spectrometer must be operated in vacuum. Further, producing an efficient high etendue long wavelength spectrometer with extremely high scan speeds in vacuum is a major challenge. Also long distance (~ 43 meters) transmission of very low in-situ calibration source power (~ nW level) with an ultra-wide frequency range is another challenge for the transmission line development. For the purpose, a prototype polarizing Martin–Puplett interferometer has been developed to operate in a low vacuum with high throughput and excellent time resolution of 10 ms with scanning length of 15 mm. And also a prototype transmission line to be used in vacuum is developed. An experimental set up has been established at ITER-India lab to test the performance of various prototype subsystems of the ECE diagnostic. The experimental set up consists of the high temperature black body source in this frequency range, transmission line and the Martin-Puplett interferometer with data acquisition system. This paper describes the experimental set up and preliminary results of subsystems developed for ECE diagnostic.

Speaker: Dr HITESH KUMAR PANDYA (Institute for Plasma Research)

Summary Slide FEC2018.pptx

135 Progress in Development and Fabrication of the JT-60SA ECH/CD System

Development of the ECH/CD system for JT-60SA has been progressed. Successful results on the JT-60SA gyrotron development for multi-frequency, high-power, long-pulse oscillation such as 1 MW/100 s at both 110 and 138 GHz, 1.9 MW/1s and 1.5 MW/5s at 110 GHz, 1.3 MW/1.2 s at 138 GHz and 1 MW/1 s at 82 GHz were reported in IAEA FEC in 2014 and 2016. The development of the high-power, long-pulse and multi-frequency JT-60SA ECH/CD system is now focusing on the launcher, transmission line (TL), control and power supply. In addition, design, fabrication and testing of a part of these components have been progressed toward start of the first plasma experiment of JT-60SA. The main results achieved in this time are as follows. (i) A full length (~7 m) mock-up of the mirror steering structure of the launcher has been successfully tested in vacuum. The required life without maintenance, which is 10^5 cycles for the poloidal steering range of 60° and 10^4 cycles for toroidal beam steering range of 30°, has been achieved. A newly introduced solid lubricant enabled the smooth movement of the steering shaft by reducing the sliding resistance between balls and rail/block of the linear guide used in the steering structure. (ii) The temperature rise distribution of aluminum waveguides has been measured at high-power of 0.5 MW. It is in the range from 0.2 to 1.2 °C per 1 MJ transmission and acceptable for 1 MW/100 s (100 MJ) transmission required in JT-60SA. (iii) The preparation of the JT-60SA ECH/CD system is progressing as planned. For instance, an ECH/CD control system has been designed with a layered and distributed structure to achieve sufficient flexibility for upgrading and for easy optimization depending on the experimental purposes. In addition, fabrication of TL components including waveguides, cooling and vacuum system has been started. Moreover, the new power supplies for two gyrotrons (1 MW/100 s each) have been designed and the fabrication has started by F4E as a part of broader approach activities. The above discussed progresses in the launcher/waveguide developments and the design /fabrication of the JT-60SA ECH/CD system components significantly contribute to smooth start of the JT-60SA experiment and improve the plasma performance with high reliability and flexibility.

Speaker: Dr Takayuki Kobayashi (National Institutes for Quantum and Radiological Science and Technology)

IAEA_FEC_2018_summary_onepage_FIP_P1-8_TKobayashi.pptx

136 Progress on Lithium Ceramic breeder materials development, Characterization and R&D activities in IPR

Several materials have been developed and being investigated for reliable and sustainable breeder candidate material. Lithium meta-titanate (Li2TiO3) and Lithium ortho-silicate(Li4SiO4) are the prominent among the suitable candidate materials for breeders. India has proposed lithium meta-titanate (Li2TiO3) as the tritium breeder materials in the form of pebble bed for LLCB TBM. Li2TiO3 power was prepared by solid state reaction using LiCO3 and TiO2 followed by ball-milling and calcination. Li2TiO3 pellets and pebbles are prepared from this powder followed by high temperature sintering. Effect of sintering time and temperature on the properties of pebbles has been studied. At every stage of preparation, extensive characterizations are being carried out to meet the desired properties of these materials.The geometry and loading conditions of the breeder blankets makes the analysis complex. For a robust design of blankets requires a thorough understanding of the thermo-mechanical response of the breeder materials at different loading conditions. In this context, the material characterization plays a vital role in determining the breeder response.It is essential to measure the mechanical and thermo-mechanical properties of pebble bed. Experimental set ups have been built indigenously at IPR for the measurement of effective thermal conductivity of pebble bed using steady state-axial heat flow and transient hot wire methods. The effective thermal conductivity (keff) of pebble beds is an important parameter for the design and analysis for a fusion tritium breeder blanket. The keff of Li2TiO3 pebble bed is measured as a function of average bed temperature from RT to 500 °C in different environment (vacuum, helium gas etc.).Initial results obtained from these experiments will be discussed in this paper. Details of lithium ceramic breeder material development, their characterizations and related R&D activities will be discussed in this paper.

Speaker: Dr Paritosh Chaudhuri (Institute for Plasma Research)

Pre_Print_IAEA-CN-258_FIP_P1-24.pdf

Summary_Slide.pptx

137 R&D status of Indian Test Facility for ITER DNB characterization

Indian Test Facility (INTF) is a R&D facility under development at Institute for Plasma research (IPR), Gandhinagar as a part of the neutral beam development from negative ion source (NNBI) program. The major advantage of the INTF besides developing the beams from large ion sources is to characterize and benchmark the ITER Diagnostic Neutral Beam (DNB) to the desired specifications over transport lengths of ~ 21m, a unique feature of this test bed. Such a study will enable establish the expected power to be delivered by DNB into the ITER plasma, an important parameter to estimate the S/N ratio expected from the He ash measurements by CXRS in ITER plasmas. The INTF beam line has a one to one correspondence with the DNB in ITER in terms of the components, their placement and the inter component distances. However, the 9 m long 4.5 m dia vacuum vessel with a top openable lid and with double O rings seals for the vacuum is different from the rectangular vessels envisaged at ITER. The other difference is the 12 number of modular cryopumps providing the same pumping surface as the single panel ITER cryopumps. In addition, the beam characterization at 21 m is planned with a second calorimeter housed in the vacuum vessel connected to the end of the duct. The Data acquisition and Control system is developed using ITER CODAC platform and integrates around 800 channels from all plant systems for enabling safe remote operations. Extensive physics and thermomechanical calculations for various types of operational heat loads and loads due to various accidental scenarios have been performed to finalise the component design. Adequate choice of materials, manufacturing and jointing processes compatible to ITER safety standards has been made in order to make the components adhere to the safety and quality classification thereby ensuring that the components survive the ITER life time while operating in harsh nuclear environments. The components are currently in various phases of manufacturing and the first operations INTF are anticipated in Q4 of 2019. The experiments on INTF are supported by single driver test bed, ROBIN, and the two driver TWIN source. The paper will describe the R&D status of different components and auxiliary systems of Indian Test Facility (INTF), the envisaged experimental program of operation and some results from operational test beds.

Speaker: Prof. Mahendrajit Singh (ITER - India Institute for Plasma Research Bhat Gandhinagar Gujarat 382428 India)

summary-slide-FIP-P1-40.pdf

138 Recent Progress on the Production and Testing of the ITER Central Solenoid Modules

Several key milestones have been completed recently in the fabrication of the Central Solenoid (CS) modules for ITER. The qualification coil has been completed and tested with many lessons learned that have now been incorporated into the processing of the production modules. Currently four modules are in production with the first module scheduled for completion in 2018 followed by full current testing at 4.5K. Shipment of the first module to Cadarache is scheduled for 2019, arriving in advance of its need date. The Central Solenoid is a key component of the ITER tokamak providing the inductive voltage to initiate and sustain the plasma current and to position and shape the plasma. The design of the CS has been a collaborative effort between the US ITER Project Office (USIPO), the international ITER Organization (IO) and General Atomics (GA). GA is fabricating seven 110 tonne CS modules (one is a spare). After arrival at the ITER site, the six modules will be stacked in the Assembly Hall, the structure added and transferred in a single lift to the ITER tokamak. In a dedicated facility in Poway, California, USA, GA is currently fabricating the modules, with each one requiring approximately 22 months start to finish. Following fabrication a series of tests including high voltage testing of the insulation, full current testing of the conductor at 4.5K and a repeat of the high voltage tests at room temperature are performed. The testing duration is an additional five months for each module and is the program critical path. Recently, the qualification coil was completed, electrically tested, and cooled to 4.5K by supercritical helium. While at 4.5K, a series of tests were performed which simulated those tests that will be performed on the modules to validate the test methods and equipment. After the tests were completed, the mockup coil was dissected to determine the quality of the resin injection. This paper describes some of the challenges in accomplishing the recent milestones in completing the qualification coil fabrication and testing, the implications on the module production, and the status of the module production.

Speaker: Mr John Smith (General Atomics)

139 RFQ Commissioning of Linear IFMIF Prototype Accelerator (LIPAc)

The IFMIF project aiming at material tests for a future fusion DEMO reactor is under the EVEDA phase in the BA Agreement of fusion program between Japan and EU. As the accelerator activity, the installation and commissioning of the Linear IFMIF Prototype Accelerator (LIPAc) is at the second stage of demonstration of the feasibility of the low energy section of an IFMIF deuteron accelerator up to 9 MeV with a beam current of 125 mA, CW. The installation of injector, RFQ, MEBT, D-Plate and LPBD for LIPAc with 8 coaxial high-power transmission lines and RF power system was just done in 2017 at Rokkasho, Japan. After that, the RF conditioning of RFQ for beam commissioning is underway. The beam commissioning of RFQ with H+/D+ and the acceleration demonstration up to 5MeV-125mA-0.1% duty cycle with D+ will be done.

Speaker: Dr Atsushi Kasugai (Japan Agency for Quantum and Radiological Science and Technology (QST), Rokkasho Fusion Institute)

FEC2018_FIP_P1-13_summary.pdf

FEC2018_FIP_P1-13_summary.pdf

140 Runaway electron beam stability and decay in COMPASS

Runaway electrons (REs) as one of the yet unsolved threats for ITER and future tokamaks are a topic of intensive research at most of the tokamaks. The experiments performed on COMPASS are complementary to the experiments at JET and MST (Medium-Size Tokamaks), building on the flexibility of the diagnostics set-up and low safety constraints at this smaller (R0=0.56 m, a=0.23 m) device. During the past couple of years two different scenarios with the RE beam generation triggered by gas injection have been developed and investigated. The first one is based on Ar or Ne massive gas injection (MGI) into the current ramp-up phase leading to a disruption accompanied by runaway plateau generation, while the second uses smaller amounts of gas in order to get runaway current dominated plasmas. The successful generation of the beam in the first scenario depends on various parameters, including the toroidal magnetic field. The generated beam is often radially unstable, and the stability seems to be a function of various parameters, including the value of current lost during the CQ. Surprisingly, the current decay rate of the stable beams is rather similar in most discharges. The second scenario is much more quiescent, with no observable fast current quench. This allows to better diagnose the beam phase and also to apply secondary injections or resonant magnetic perturbations (RMP) to assist the decay of the beam. In this regard, interesting results have been achieved using secondary deuterium injection into a runaway electron beam triggered by Ar or Ne injection and also using n=1 error field generated by top and bottom RMP coils. While D dilution is clearly able to almost stop the beam decay, RMPs help to accelerate the beam decay. The effect of RMPs seems to be very different when acting on Ar and Ne background plasmas. Very interesting effects have been observed also by the high-speed cameras, including filamentation during the application of the RMPs and a slow local variation of the light intensity similar to turbulence during the beam decay.

Speaker: Mr Ondrej Ficker (CzIPP, CzFNSP)

IAEA_FEC_2018_Ficker_poster_final.pdf

141 Seismic Analysis Of High Power Amplifier in ITER ICRF Range

ITER-India is responsible for delivery of 8+1(prototype) RF sources to ITER project. Each RF source will provide 2.5MW of RF power at VSWR 2:1 in the frequency range of 35 to 65MHz. Eight such RF sources will generate total 20MW of RF power. Two RF chains containing three high power amplifiers (HPA1, HPA2 and HPA3) need to be combined to build an RF source. HPA2 and HPA3 are RF tube based amplifiers while HPA1 is a solid state power amplifier. This paper covers detailed seismic analysis of High Power Amplifiers for worst case seismic loading condition. A SL-2 seismic event has been analyzed to determine potential areas that will require inspection and/or replacement. According to the design basis, a Response Spectra Analysis (RSA) has been performed for the frames and cavity of high power amplifiers which includes the self-weight of all structural members, platform dead weight and reactions from the base. The RSA requires a modal analysis to be performed which is used to determine the rigidity of the support structures. The accelerations of the Zero Peak Acceleration (ZPA) are applied in order to account for all masses. All structures and components must respect the requirement that there must be no failure that would prevent a SIC-1 or SIC-2 component from performing its safety function. The ANSYS software is used for Modal analysis and Response Spectrum analysis. This paper will also point out the maximum stressed link in structure and modifications may be proposed to achieve the required strength.

Speaker: Mr Rohit Anand (ITER India , IPR)

142 Shattered Pellet Injection Technology Design and Characterization for Disruption Mitigation Experiments

The technology of forming high-Z cryogenic pellets mixed with D2 that are shattered upon injection into a plasma has been developed at ORNL for mitigating disruptions and has been selected as the basis for the baseline disruption mitigation system on ITER. In these shattered pellet injectors (SPIs), large pellets of neon and argon mixed with D2 are formed from gas and are shattered upon impact with a bent tube just before entering into disrupting plasmas in order to radiate the plasma energy to mitigate possible damage to in-vessel components [1]. In support of disruption mitigation research for ITER, SPI systems have been designed and fabricated for use on thermal mitigation and runaway electron dissipation experiments on DIII-D and JET. These systems have common features of 3 barrels of different size pellets that are formed in-situ and collimated into a single injection line. The shatter tubes are bent stainless steel tubes that are mounted inside the vacuum vessel of the tokamak. The large pellets are formed in-situ from the low pressure gas feed into the barrels that are cooled with liquid helium and held intact ready to fire until needed. Pressurized gas is also used to accelerate these pellets with gaps in the injection lines to remove as much of the gas as is practical to avoid influencing the plasma shutdown. Solid pellets of argon in particular present a challenge to fire the pellet because of high shear stress, thus mechanical punches have been developed that can apply higher impact to release these pellets. Punches using high pressure gas and solenoid drivers have been developed. Tests of gas punches have revealed that argon can be released and achieve speeds up to 160 m/s for 8 mm size pellets. The slower pellet speeds achieved with a punch have been found to result in larger fragment sizes, which is appealing for deeper penetration in high performance plasmas. Higher speed pellets that are achieved with high pressure gas and high deuterium content in the same shatter tube result in finer particles and higher gas content in the resulting shatter material spray. [1] N. Commaux, et al., Nucl. Fus. 50 (2010) 112001. [2] L. R. Baylor, et al., Fus. Sci. Tech. 68 (2015) 211.  This work was supported by ORNL managed by UT-Battelle, LLC for the U.S. Department of Energy under Contract Nos. DE-AC05-00OR22725 and DE-FC02-04ER54698.

Speaker: Dr Larry R. Baylor (Oak Ridge National Laboratory)

FIP_P1-1_Slide_Baylor.pdf

143 Singlet Breakdown Optimisation to a Doublet Plasma Configuration on the TCV Tokamak

This paper presents a fresh attempt on TCV to optimise plasma breakdown in the break-less (45 micro-Ohm impedance) vacuum vessel culminating in a double breakdown and the formation of a doublet configuration. A statistical analysis of legacy single pole breakdown and early plasma current ramp failures helped modify vessel current estimators together with PSU command and control issues to obtain reliable plasma initiation +/-30cm in TCV’s 3:1 elongated vacuum vessel. Although precise control of the vacuum null was achieved, control of the high plasma ramp rate proved complex since the highest (~10v) loop voltage was necessary for reliable breakdown and, through trial, the acceptable range of pre-fill pressures was limited. A double breakdown with simultaneous, separated, magnetic nulls was then achieved. Initial ohmic heating alone was limited by lobe separation instabilities with the upper lobe merging into the lower lobe after ~15ms. Plasma multipole control was attempted using two X2 gyrotrons, aimed at each lobe’s, core to modify each lobe’s resistivity and thus current. A transport barrier in the mantle surrounding the doublet configuration was observed with both lobes seemingly heating independently of the ECH heating location. To date a combined plasma current of 260kA after 20ms was obtained for which Thomson density and temperature profiles indicate two clear plasma lobes. Doublets are predicted to offer increased Beta limits, vertical stability and the potential of a novel solution to divertor exhaust where the entire mantle, surrounding the plasma, may be available for exhaust dissipation.

Speaker: Dr Basil Duval (Ecole Polytechnique Fédérale de Lausanne – Swiss Plasma Center (SPC), Association Euratom-Confédération Suisse(EPFL) CH-1015 Lausanne, Switzerland)

IAEA_BPD18.pdf

144 SOL transport and detachment in alternative divertor configurations in TCV L- and H-mode plasmas

The effect of magnetic geometry on scrape-off layer (SOL) transport and detachment behavior is investigated on the TCV tokamak with the goal of assessing the potential of alternative divertor geometries and for the validation of theoretical models. L-mode experiments reveal that increasing connection length and hence divertor volume by either increasing poloidal flux expansion or divertor leg length have different effects on the boundary plasma. In attached conditions, the SOL heat flux width l_q inferred from target infrared thermography measurements is weakly dependent on poloidal flux expansion but increases approximately with the square root of the divertor leg length. The divertor spreading factor S shows no clear trend with leg length but decreases with flux expansion. TOKAM3X turbulence simulations of the leg length scan are in qualitative agreement with the experiment and can explain observations by a strongly asymmetric (ballooning) transport at and below the X-point. Evidence for increased transport in the region of low poloidal field is obtained in the Snowflake minus geometry. The presence of an additional X-point in the low-field side SOL increases the effective SOL width by approximately a factor two. Increasing flux expansion and leg length both result in enhanced divertor radiation levels, with the effect being much larger in the latter case. This behavior, together with the observed trend in l_q, is consistent with a substantial drop in the density threshold for divertor detachment with increasing leg length and a weak variation with flux expansion. Novel spectroscopic techniques reveal that the drop in target ion current and access to detachment is caused by a reduction of the divertor ionization source due to power starvation, while volume recombination is only a small contributor. This interpretation is confirmed by SOLPS modeling. TCV alternative divertor studies are being extended to neutral beam heated H-mode plasmas. The H-mode power threshold is found to vary weakly between standard, X-, and Super-X geometries. In all cases, ELMy H-mode is obtained at intermediate current, while the discharges are ELM-free at high current. Signs of detachment have so far only been observed in the latter case. Ongoing experiments further investigate H-mode detachment in these plasmas and will be extended to Snowflake configurations.

Speaker: Prof. Christian Theiler (EPFL-SPC)

Summary_slide_Theiler_EX_P1_19.pptx

145 Steady states for nonaxisymmetric rotating toroidal plasmas

Small applied nonaxisymmetric magnetic fields have been demonstrated to have strong and complex effects on otherwise axisymmetric toroidal fusion plasmas. Their importance raises the question of the best ``steady state'' plasma configuration to use for their analysis. A steady state that is valid on fast time scales of a few Alfvén times is needed to invert and interpret experimental measurements and as an initial state to study slower-developing plasma instabilities and plasma processes. It should possess a magnetic flux function Psi with B dot grad(Psi)=0 and a well-confined boundary surface that confines the magnetic field lines. It contains free functions and parameters that must be taken from observations or outside models. The simplest choice is ideal MHD. Axisymmetric and helical MHD plasmas with zero plasma flow possess a good flux function, the plasma pressure, which in axisymmetry is equivalent to the poloidal magnetic flux psi. Axisymmetric states with plasma rotation have two functions, psi and the centrifugally shifted plasma mass density, which represent electron and ion surfaces, respectively. The shifted density modifies the mapping of experimental density to magnetic flux surfaces and allows larger density gradients at the large-R boundary of the torus. Magnetic nonaxisymmetry due to external fields couples the two functions. In single-fluid MHD, the coupling can be shown to impose strong and probably unrealistic constraints on the allowable variation of the rotation and density relative to the magnetic field. Two-fluid models decouple the electron and ion motions and allow greater freedom that removes the restrictions. They also have other properties that reflect experimental observations. The proposed solutions will be studied for experimental cases with rotation and nonaxisymmetry, by numerical simulation with the nonlinear extended MHD code M3D [1], using the real nonaxisymmetric fields. The results will also be compared to the nonlinear evolution. *Work partially supported by U.S. DOE OFES contract DE-SC0007883. [1] Park, W. et al. 1999, Phys. Plasmas 6, 1796; Sugiyama, L.E., and Park, W. 2000, Phys. Plasmas 7, 4644.

Speaker: Linda Sugiyama (M.I.T.)

L_Sugiyama_TH:P1-4_summary_slide.pptx

146 Study of Corrosion Properties ITER In-Wall Shield (IWS) Fasteners and Structural Integrity of IWS

In-Wall Shield(IWS) Blocks will be inserted between inner and outer shell of ITER Vacuum Vessel. These blocks comprise of number of plates of Stainless Steel stacked together using fasteners of XM-19 and M30 size. Plates are tightened with pretension of 107 kN to withstand EM force of 1.83 × 104N during ITER operation. These bolts are spot welded with blocks to lock any type of rotation. There are approximate 1500 such bolts exposed to vacuum in one vessel sector with approximate surface are of 70.5 m2. Hence, surface condition of these fasteners play an important role while leak testing of VV. XM-19 material is very corrosive resistant but, if the fasteners are exposed to normal or humid environment for a long time its surface may get oxidised and catch the corrosion which may further impact the ITER operation in three ways: (a) Reduced Structural Integrity of blocks (b) Gas load due to Outgassing(c) Generation of corrosion products in Cooling Water System. This corrosion has been assessed by (a) Measuring the Corrosion rate (CR) of XM-19 fasteners (exposed in natural environment) and (b) XM-19 washer exposed to water with ITER operating temperature and pressure. This study is carried out using Scanning Electron Microscope (SEM) and Electrochemical Polarization Technique. For SEM analysis, samples were polished and corrosion depth was measured and accordingly CR was calculated. In Electrochemical Polarization Technique, samples were induced with corrosion at room temperature and high temperature in water medium. Pt electrode was used as cathode and Ag-AgCl3 as reference electrode. CR was calculated with the help of corrosion current. Tafel curves of corroded samples show that, reverse polarization path do not intersect the forward path and indicate no tendency of pitting corrosion. Maximum corrosion observed by using Tafel curve is 0.1067 mpy. Outgassing rate of naturally corroded XM-19 bolt was measured 6.06 E-8 Pam3s-1m-2 which is less than the acceptable limit for IWS. Total corrosion product for one Vessel sector was calculated with the help of CR and surface area in one vessel sector and found 3.20 Kg/year. It can be removed by appropriate filters. Study shows that corrosion and out gassing properties of corroded XM-19 fasteners are acceptable for ITER IWS. Detailed experimental set up and results of corrosion study will be presented in this paper.

Speaker: Ms Abha Maheshwari (ITER-India, Institute for Plasma Research)

Manuscript-Abha-FEC.pdf

Manuscript-Abha-FEC-v1.1.pdf

147 Subdivertor fuel isotopic content detection limit for JET and impact on the control of ICRH for JET-ILW and JET-DT operation

In preparation for JET Deuterium-Tritium Experiments 2 (DTE-2) and to assure readiness to provide fuel cycle-relevant measurements, the subdivertor fuel isotopic ratio detection limit, as determined by Penning optical gas analysis (OGA) [1, 2], was recently researched. Reevaluation of OGA data from DTE-1 [1] revealed a 1% uncertainty (error bar) at the 1% T/(H+D+T) concentration level. A similar detectability limit (at ~1% concentration) was found for H/(H+D) when evaluating a more recent JET ICRH-specific dataset. This analysis also shows a persistent ~ 1% systematic offset of the OGA with respect to divertor spectroscopy values. These studies are in support of substantial diagnostic upgrade for DTE-2 aiming to assure this isotopic detectability, as well mitigate gradual deterioration partly caused by coating of viewport windows by the OGA’s own Penning discharge. The importance of resolving isotopic concentrations at the ~1% level during ICRH plasmas was also explored. When (H/(H+D)) is reduced from 2% to <1%, an increase of core plasma Ti and a decrease of Te are measured [3, 4]. This is consistent with full wave ICRH modelling indicating that when the concentration of the minority species is low enough, 2nd harmonic D absorption becomes dominant over the fundamental H minority absorption; if the plasma density is large enough, it provides collisional bulk ion heating rather than the typical electron heating observed with H minority absorption. The higher background Ti in conjunction with the RF acceleration of the D NBI ions to supra-source energies leads to an increase of the neutron yield by 30% in the case explored. For the same case, the increase of the energy of the fast H tail at small minority concentrations also contributes to sawtooth stabilization. This would imply that the ability to measure, and ultimately control, the fuel isotopic content down <~ 1% concentration level is important for optimizing the performance of a given ICRH scheme in fusion devices. The ability of the OGA technique to act as a global diagnostic of the isotopic mix is of great consequence for ITER, where divertor spectroscopy is unlikely to work, at least for such low concentrations [2].-- [1] D.L. Hillis et al., RSI 70 (1999) 359; [2] C.C. Klepper et al., 2017 JINST 12 C10012; [3] E. Lerche et al., 2016 NF 56 036022; [4] M Goniche et al., 2017 PPCF 59 055001

Speaker: Dr C Christopher Klepper (Oak Ridge National Laboratory)

Klepper_IAEA'18_Summary-Slide_v0-3.pptx

148 Survey on Hot Isostatic Pressing Technique for development of Tokamak components

Hot Isostatic Press (HIP) equipment is basically an electric furnace which is contained in a pressure vessel. In HIP, the component is subjected to elevated temperature (generally over 1000 degree centigrade) and pressure (generally over 1000 bar) which results in fully isotropic material properties. As per 2012 estimate, approximately 1000 HIP systems have been installed worldwide. Around 50% of these HIP installations were for R&D applications. HIP is used to eliminate pores (and remove casting defects), consolidation of powder and diffusion bonding of dissimilar metals or alloys. The components are often of net shape or near net shape. HIP eliminates inspectibility issues, enables new alloy system and enhances weldability. HIP improves fatigue properties, creep properties, ductility and impact strength. It provides an alternate supply route for long lead time components. Hot Isostatic Pressing of Austenitic Stainless Steel Powders for pressure retaining applications is reported in The American Society of Mechanical Engineers (ASME) proceedings. The technology has developed over the last 20 years and HIP can now produce twice as much product using the same type of machine as they could twenty years ago. The capability of producing full dense near net shape product can be utilized for multilayered plasma facing components fabrication. Joining of various dissimilar materials is possible, such as tungsten to copper joining, Copper to copper alloy, SS to CuCrZr material etc. using HIP. The fabricated joints are reported to be satisfactory. Many fusion components are also fabricated through powder metallurgy route using HIP technique. In this paper, we have performed a survey on applications of HIP in various R&D in fusion community. Some offshore applications, interesting applications in science projects and application for additive manufactured components etc. shall also be discussed.

Speaker: Mr Gautam Vadolia (Institute for Plasma Research)

149 The concept of lithium based plasma facing elements for steady state fusion tokamak-reactor and its experimental validation

The modern results on the implementation of the Russian strategy in the development of designs of long-operating plasma facing element for steady state fusion reactors are considered and analyzed on an example of liquid metal limiters of tokamaks Т-15 and FTU. The experimental validation of this strategy is presented and results on liquid metal CPS behavior in tokamak conditions, effective heat removal up to 12 MW/m2 with low pressure heat transferring medium (0.2 MPa) on the basis of a gas-water spray are considered. The promising scheme of liquid metal divertor target plate for DEMO reactor is presented and discussed.

Speaker: Mr Alexey Vertkov (SC "Red Star")

EX-P1-12.pdf

EX-P1-12.ppt

150 The impact of poloidal flux expansion on JET divertor radiation performance

For a burning plasma device like ITER, radiative power removal by seeded impurities will be inevitable to avoid divertor damage. Increasing divertor radiation by injecting low-Z impurities such as nitrogen, to reduce scrape-off layer heat flux and to cool the divertor plasma to detachment, is put forward as the primary method to achieve this goal. Here, the possibility of increasing the radiative fraction is assessed by using poloidal magnetic flux expansion. Initial ohmic and nitrogen seeded H-mode High Flux Expansion (HFE) experiments, characterized by the presence of 2-nearby poloidal magnetic field nulls and a contracting geometry near the inner target plate have been recently achieved at JET tokamak In this contribution the physics of the dependence of radiative volume and total radiated power on flux expansion variation at JET, equipped with ITER-like Wall (ILW), will be addressed. EDGE2D-EIRENE simulations have already shown that the divertor heat fluxes can be reduced with N2-injection, qualitatively consistent with experimental observations, by adjusting the impurity injection rate to reproduce the measured divertor radiation. Through EDGE2D-EIRENE code modelling, a detailed analysis of the power balance has been set up to physically investigate the reason of the increase of the radiated power for HFE discharges. An increase of charge exchange losses has been related to an increase of connection length and flux expansion both at X-point at strike points position. Spectroscopy data suggests that there is evidence of a detachment front moving towards the X-point from both the movement of the electron density and the low charge nitrogen charge states as the flux expansion increases. Initial experiments with a second null, on the high field side, forming a configuration with significant distance between the two nulls and a contracting geometry near the target plates have been performed leading to an increase of the main magnetic divertor geometry parameters. In addition, nitrogen seeded H-mode experiments have been set-up showing an increase of the total radiated power of the same factor of the flux expansion increase. Further experiments will be devoted to varying the divertor coils polarities to move the secondary x-point on the low field side region and consequently increase the outer flux expansion both in the x-point and strike point region.

Speaker: Prof. Gianmaria De Tommasi

151 The influence of displacement damage and helium on deuterium transport and retention in tungsten

Among many other favorable properties of tungsten its low intrinsic fuel retention makes it a promising candidate as plasma facing material. However, during operation defects in the tungsten lattice will evolve that will trap hydrogen isotopes. While for present day devices this increased retention is only limited to the near surface it will take place throughout the whole bulk in future nuclear devices as a consequence of the neutron irradiation. There is not yet a microscopic understanding that would allow to describe the processes that will prevail in a reactor environment quantitatively, where damage creation and hydrogen retention will mutually influence each other. Present day predictions are only based on extrapolation of data collected from non-nuclear machines. Hence, the influence of hydrogen on defect production, the influence of defects on hydrogen isotopes transport as well the influence of the presence of helium (directly implanted close to the material surface from the plasma as well as produced throughout the bulk by tritium decay and transmutation) is not considered in these extrapolations. Implantation of different ion species with energies in the MeV range can be used to simulate the displacement damage neutrons will cause. Contrary to neutron irradiation, ion beam irradiation is fast and does not activate the samples. Likewise, the influence of He on transport and retention can be studied by implanting He with MeV-energy deep into the material. In this way surface effects can be separated from bulk effects. These kind of experiments allow dedicated parameter studies under well controlled conditions. In this contribution such benchmark experiments on transport and retention of deuterium in displacement damaged and helium containing tungsten are presented that allow to test and extend present day understanding on a quantitative level. The dependence of deuterium retention on the damage level, the influence of damage rate as well as the influence of the specific ion used to create the displacement damage will be shown. Results from hydrogen isotope exchange experiments are presented that reveal the dynamics of hydrogen transport which is a chain of trapping and detrapping processes. Rate equation modelling without free parameters is used to describe the observed uptake during plasma exposure as well as the release during annealing.

Speaker: Dr Thomas Schwarz-Selinger (Max-Planck-Institut für Plasmaphysik)

Schwarz-Selinger_summary slide_CN258-248_P1-18.pdf

152 The influence of Fe-ion irradiation on the microstructure of reduced activation ferritic-martensitic steel Eurofer 97

The reduced-activation ferritic-martensitic steel Eurofer 97 is the European benchmark structural material for in-vessel components of fusion reactor. Experimental data on neutron irradiated Eurofer 97 material have shown decrease in plasticity and radiation hardening at irradiation temperatures about 300 °C. Formation of dislocation loops and α' pre-precipitates is considered as the main reason of this phenomenon. In this work Eurofer 97 steel was irradiated with Fe ions up to 10^16 ions/cm^2 at 250, 300 and 400 °C. The irradiated samples were characterized by TEM and APT. TEM study of ion irradiated samples revealed nucleation of dislocation loops. The pair-correlation analysis of APT data detected an initial stage of solid solution decomposition. The hardening of ion irradiated Eurofer 97 was calculated with DBH model taking into account radiation-induced dislocation loops to comparison with the change of yield stress for neutron irradiated Eurofer 97. According to obtained results it can be supposed that the formation of dislocation loops plays the main role in the low temperature radiation hardening of Eurofer 97 at the dose level up to ~10 dpa.

Speaker: Dr Sergey Rogozhkin (SSC RF ITEP of NRC “Kurchatov Institute”)

153 The Operation, Control, Data Acquisition System of ASDEX Pressure Gauge for Neutral Pressure

The Bayard-Alpert (BA) type hot cathode ionisation gauge is widely used to measure neutral pressure precisely in vacuum system below 10-3 Torr pressure. Neutral pressure measurement in magnetic confinement fusion experiments is quite challenging for standard BA type gauge due to higher pressure limitation and its ionisation is affected by high magnetic and electrical fields. To overcome above limitations, A special hot cathode ionisation gauge, named ASDEX Pressure Gauge (APG) system has been developed by G. Haas at the Max-Planck-Institute, Germany \cite{Haas}. The APG system works in high magnetic field upto 6 Tesla and high temperature plasma environment with broad pressure measurement range from 10-1 to 10-6 mbar with fast response (<10 msec) and good noise immunity. For ADITYA Tokamak, A customised system of operation, control and data acquisition for standard APG system has been designed and developed to measure real time neutral pressure during high temperature plasma discharges. The developed system can achieve synchronous control of gauge controller using GPIB and data acquisition of ion and emission current of gauge head using PCI based data acquisition module. Initially, the APG calibration with standard BA type hot cathode ionization gauge had been carried out on the test setup of low magnetic field and ultra high vacuum system with different gases like H2, Ar, He. For APG calibration in various pressure range of different gases, precise gas feed control system has been developed using controller based hardware and LabVIEW software. After successfully testing and calibration, the APG was installed on ADITYA tokamak and calibrated under high magnetic field of ADITYA Tokamak. The developed APG control system has been configured to set the gauge parameter before the plasma discharge and acquired real time analog signal acquisition using simultaneous sampling by analog to digital convertor (ADC) during plasma discharge. The acquired raw data and processed real time pressure measurement gives valuable neutral density information to tokamak plasma.

Speaker: Mr Kiran PATEL (Institute for Plasma Research)

154 The Software and Hardware Architecture of the Real-Time Protection of In-Vessel Components in JET-ILW

The JET ITER-like wall (JET-ILW) combines plasma-facing components (PFC) made of bulk beryllium for main chamber limiter tiles and of bulk tungsten as well as tungsten coated CFC tiles for divertor tiles. The risk of damaging the metallic PFCs caused by beryllium melting or cracking of tungsten owing to thermal fatigue required a new reliable active protection system. To address this issue, a real time protection system comprising newly installed imaging diagnostics, real time algorithms for hot spot detection and alarm handling strategy has been integrated into the JET protection system. This contribution describes the design, implementation, and operation of the near infrared (NIR) imaging diagnostic system of the JET-ILW plasma experiment and its integration into the existing JET protection architecture. The imaging system comprises four wide-angle views, four tangential divertor views, and two top views of the divertor. Regions of interest (ROI) on the selected PFCs of different materials are analysed in real time and the maximum temperature measured in each ROI is sent to a real time algorithm called vessel thermal map (VTM) to determine the likely cause of the overheating and to request an appropriate response from the plasma control system. Post-pulse data visualization and advance analysis of all types of imaging data is provided by the new software framework JUVIL (JET Users Video Imaging Library). The hot spots formation at the re-ionization zones due to impact of the re-ionised neutrals as well as due to RF-induced fast ion losses is recognized as a big threat due to quick surface temperature rise. Because it could trigger the protection system to stop a pulse, it is important to identify the mechanisms and conditions responsible for the formation of such hot spots. To address this issue a new software tool Hotspot Editor has been developed. Future development of the JET real time first wall protection is focused on the D-T campaign and the ITER relevant conditions which will cause failure of camera electronics within the Torus hall. To provide the reliable wall protection, two more sensitive logarithmic NIR camera systems equipped with new optical relays to take images and cameras outside of the biological shield have been installed on JET-ILW and calibrated with in-vessel calibration light source.

Speaker: Mrs Valentina Huber (Forschungszentrum Jülich GmbH)

Summary.pdf

VHuber_IAEA2018_paper_v14.pdf

155 Thermal Analysis of Protection Important Components of ITER XRCS-Survey Diagnostic System

In the ITER, an important aspect of qualifying the components to the mandatory regulatory requirements, the system developers have a challenge to first design the components fulfilling guidelines of the ITER recommended French nuclear code RCC-MR (2007) and later on demonstrate to the regulator. It is even more involving for systems that are extending primary vacuum to the interspace and port-cell as these zones are accessible by a human. The paper addresses such requirements in the thermal design of the X-Ray Crystal Spectroscopy-Survey (XRCS-Survey) system, which is a first plasma diagnostic.
The XRCS-Survey is a broadband (1 - 100 Å) X-ray crystal spectrometer for real-time monitoring of absolute concertation and in-flux of the plasma impurities. For measurements, the transport of x-ray emission is done using a nearly 10m long sight-tube directly connecting the spectrometer to the closure plate of the port-plug. The sight-tube components, classified as Protection Important Components due to their function in confinement of radioactive tritium and dust, are subjected to various thermal loads while machine operations. These loads are mostly due to baking to achieve ultra-high vacuum inside the ITER vacuum vessel. Furthermore, the components are also subjected to a neutron, gamma radiation of D-T fusion.
For reliable performance and safe operation of XRCS-Survey diagnostic, a preliminary engineering design and ANSYS analysis of the XRCS-Survey sight-tube components have been performed, with and without radiation shielding, in order to analyze the behavior of components under baking heat loads, operational heat loads and also accidental fire heat loads.
The paper presents an optimized design layout for the sight-tube of XRCS Survey and results of the thermal analysis; defining temperature limits to observe compliance with safety criterion defined by ITER regulatory guidelines on PIC (class SIC-1) components as well as providing inputs to the structural integrity analysis of the system.

Speaker: Prof. Sanjeev Varshney (ITER-India, IPR)

Suammry slide_XRCS Thermal_ IAEA FIP_P1-34.pptx

156 Thermal-hydraulics and Structural analyses of LLCB TBM set

India is developing Lead-Lithium cooled Ceramic Breeder (LLCB) Test Blanket Module (TBM) for testing in ITER for the validation of fusion blanket design tools, tritium breeding performance and high grade heat extraction capability relevant to Indian DEMO. The LLCBTBM will be tested from the first phase of ITER operation (H–H phase) in one half of the ITER port no-2. LLCB TBM set consists of TBM and its shield along with supports and piping.The LLCB TBM consists of U shaped helium cooled first wall (FW) with back plate enclosing internal components covered by top and bottom plates. The TBM internals consist of four ceramic breeder canisters(Li2TiO3) in the form of pebble bedwith Pb-Li flowing around these canisters to cool the internal structure.The TBM is supported at TBM shield by supports. The back side of Shield is welded to TBM set flange, which is bolted to the ITER port plug frame.TBM Shield made of SS 316 L (N)-IG located behind the TBM is composed of steel and water with a combination of 50:50 to shield neutrons. It consists of two symmetrical parts that have grooves to accommodate pipes. The neutronic heat generated inside shield structure is extracted by water flowing inside the shield. The detailed thermal –hydraulics of TBM set has been performed based on the heat flux on FW and neutronic heat generation on TBM set. The temperature distribution obtained from thermal analysis has been used for thermo-structural analysis. CFD analysis of helium flow inside the FW channels and manifolds has been carried out to estimate temperature, pressure drop and heat transfer coefficient. The distribution of flow inside the different flow circuits of FW from manifolds and water flow in TBM Shield will also be described in this paper. Structural analysis has been performed on TBM set based on load combinations as per ITER load specifications. RCC-MR 2007 code has been used for the structural assessment for the prevention of p-type and s-type damages and calculation of safety margins. The structural analysis results of different components of TBM set which include TBM, back plate, supports,process pipes and TBM shield will be discussed in detail in this paper.

Speaker: Mr Deepak Sharma (Institute For Plasma Research)

Summary_slide_P1_55.pdf

157 Thermo-Mechanical Experiments On Lithium Titanate Pebble Bed

Among the various lithium ceramics, Li2TiO3 is one which has been received much attention due to its very excellent properties, such as reasonable lithium atom density, low activation, excellent tritium release performance and chemical stability, etc. Lithium Titanate [Li2TiO3] pebbles with the diameter of 1mm was widely used for the experiments after successful completion of variety of modeling and experiments. In the present study we have prepared lithium titanate from its high pure raw material of lithium carbonate and titanium dioxide by solid state reaction in the stoichiometric ratio. The reaction temperature has been estimated from the thermo-gravimetric and differential thermal analysis (TG-DTA) and the same scenario has been executed for the bulk production using high temperature furnace. The phase and phase stability at different temperature were analyzed by using powder X-ray diffractometer. The pebble preparation has been carried out from this raw material after once again ground them to fine powder and addition of PVA as a binder for the preparation of green pebbles using extruder-spheronizer technique. The green pebbles were sintered at high temperature to attain desired density for further studies. The details of the Li2TiO3 powder and pebble fabrication and their characterizations like XRD, density, porosity, crush load, SEM analysis, Young’s Modulus and creep will be discussed in the paper.

Speaker: Dr Riscob Bright (Institute for Plasma Research)

Summary_FEC.pptx

158 TRIGA Integral Activation of Mn foils, Li2O and LiF as Potential Tritium Production Monitors for Fusion Applications

In the future fusion reactors, such as ITER or DEMO, tritium will be produced by bombardment of lithium atoms with neutrons and several types of special Tritium Breeder Modules (TBM) will be installed in the ITER reactor to demonstrate the self-sufficiency of tritium production. LiF pellets commercially produced as Thermo-luminescent detectors (LiF - TLDs) can be used to measure tritium production. The similarities between the sensitivity profiles of the neutron reaction of tritium production in 6Li(n,t) and those of the 55Mn(n,g)56Mn reaction in the TBMs indicated that the latter reaction could be used as a tritium production monitor, at least for short-term monitoring, the half-life of 56Mn being 2.579 h. However, experimental verification and improvements and validation of the Mn cross-sections are needed in order to meet the required accuracy. In the scope of the Fusion for Energy (F4E) project of the European Commission, foils of certified reference materials Al-1%Mn and Al-0.1%Au, as well as TLD(LiF) and Li2O samples were irradiated in the JSI TRIGA research reactor, both bare, and under Cd and boron-nitride to study the potential use of Manganese detectors for monitoring the tritium production in fusion machines. In order to obtain complementary information for data validation purposes, the irradiations were performed in different neutron spectra, i.e. in the Central Channel, the Pneumatic Tube in position F24 in the outer “F” ring of the reactor core, in position F19 and in the IC-40 irradiation channel in the graphite reflector. Bare, and under Cd and boron-nitride irradiations were needed for the subtraction of epi-thermal neutron contribution in the 55Mn(n,g)56Mn reaction. Two series of measurements was performed, in 2014 and 2017. The transport calculations were performed using the Monte Carlo transport code MCNP6.1 with a detailed model of the TRIGA reactor including the irradiation capsules. The uncertainties involved in the measurements and the calculations were carefully evaluated. The principle objective was to study the energy response of the 55Mn(n,)56Mn reaction and correlations between the Mn and TLD / Li2O measurements. Good consistency between the measured and calculated reaction rates, in most cases within the uncertainty bars, was observed and will be reported in the paper.

Speaker: Prof. Ivan Kodeli (Jozef Stefan Institute)

iaea2018poster-triga.pdf

TRIGA_mn1p.pdf

159 Turbulence and radial electric field asymmetries measured at TJ-II plasmas

Dedicated experiments have been carried out for a systematic comparison of turbulence and radial electric field measured at poloidally separated positions in the same flux-surface in the stellarator TJ-II. The rationale behind this study is twofold, verification of the spatial localization of instabilities predicted by the Gyrokinetic simulations in stellarators and verification of the electrostatic potential variation on the flux surface as calculated by Neoclassical codes and its possible impact on the radial electric field. Poloidal asymmetries in the turbulence wavenumber spectrum and in the Er profile have been found that depend on density, heating conditions and magnetic configuration. These quantities have been measured using a Doppler reflectometer that covers the radial region from rho = 0.6 to 0.9, at different perpendicular wave-numbers of the turbulence: 1-14 cm-1, and at two plasma regions poloidally separated. Different plasma scenarios have been studied with different profile shapes. These include, high power on-axis ECH heated plasmas vs. low power off-axis ECH heated plasmas; ECH vs. NBI heated plasmas; standard vs. high iota magnetic configurations, and Hydrogen vs. Deuterium dominated plasmas. Differences in the turbulence intensity are found when comparing the k-spectra measured at poloidally separated positions in the same flux-surface, in ECH heated plasmas in the standard magnetic configuration. However, almost no asymmetries are found in NBI heated plasmas, i.e. higher density, lower electron temperature, where very similar turbulence intensity and spectral shape are measured at both plasma regions. Besides, no significant differences have been found when comparing Hydrogen and Deuterium dominated plasmas. The asymmetry in the turbulence intensity found in the standard magnetic configuration reverses in the magnetic configuration with high rotation transform. Radial electric field profiles measured at the two plasma regions show pronounced differences in low density plasmas, i.e. plasmas in neoclassical electron root confinement. At higher densities the Er asymmetry gradually decreases and almost disappears in ion root plasmas. The detailed comparison of the k-spectra and Er profiles under different plasma scenarios are presented, providing valuable information for comparison with Gyrokinetic and Neoclassical simulations.

Speaker: Dr Teresa Estrada (CIEMAT)

Estrada_Summary_slide.pdf

160 Validation of global gyrokinetic simulations in stellarator configurations

In this contribution, recent simulations carried out in stellarator configurations with the global gyrokinetic code EUTERPE and the ongoing validation effort are presented. The linear relaxation of zonal flows (ZFs) has been studied in global simulations in many stellarator configurations. The code has been verified by comparing results with both other gyrokinetic codes and analytical estimations. Furthermore, these calculations were validated against experimental measurements obtained during pellet injection experiments in TJ-II. The oscillatory relaxation of potential measured by the HIBP was compared to simulations including impurity ions, with a good quantitative agreement in the frequency and damping rates. This is the first experimental confirmation of the ZF oscillation in stellarators, accurately described by the linearized gyrokinetic equation. The electrostatic micro-instabilities have been studied numerically in the stellarators TJ-II and W7-X and an effort to validate simulations against experimental turbulence measurements from Doppler Reflectometry (DR) has been done. The model validation has been pursued at different levels of detail, including the density fluctuation level, frequency spectra, and the localization of instabilities along the flux surface. In dedicated experiments in TJ-II, the power and deposition location of the ECRH heating were changed, thus modifying significantly the density and temperature radial profiles. The experimental measurements from the DR system in TJ-II have been compared to simulations. The relevant wave-numbers and the radial variation of experimental density fluctuations spectra are consistent with the range of unstable wave-numbers and the location of maximum instability found in simulations. No dependency of the power spectra with the bulk ion mass is observed experimentally, which is consistent with the kind of unstable modes (electron-driven) found in simulations. A systematic difference is found between the density fluctuation spectra measured by the DR system at poloidally separated positions on the same flux-surface, which is largely affected by the rotational transform. The localization of instabilities in simulations is also influenced by the rotational transform, however, a discrepancy between the location of maximum fluctuation level in simulations and experiments is found so far.

Speaker: Dr Edilberto Sánchez (Laboratorio Nacional de Fusión, CIEMAT)

161 Verification tests for remote participation at ITER REC

The ITER Remote Experimentation Centre (REC, [1]) in Rokkasho is one of the projects implemented within the Broader Approach (BA) agreement [2] as part International Fusion Energy Research Centre (IFERC). The long-term objective of the REC is to allow researchers to take part in the experimentation on ITER from a remote location. On a shorter time scale, before ITER will be operated, the REC facility will be used to test technologies for remote participation in collaboration with existing European tokamaks [3] and with JT-60SA, whose first operations are envisaged in 2020 [4]. Other than setting up and equipping the REC control room (see also [5]), during the first phase of the REC (2013-2017) the scope of the project included activities aimed at developing and evaluating software tools for fast data transfer, remote participation, data analysis, and plasma simulation. These activities have been carried out by an Extended-Integrated Project Team (E-IPT). Indeed, due to the characteristics of the remote experiment, the collaborations with experts in other institutes providing experimental data, network infrastructure, data transfer protocol, and experiences on inter-continental data transfer and data acquisition were essential for the success of the REC activities. As a consequence, members from different Japanese and European institutions were invited to join in E-IPT; among the various contributors, there are members of the ITER project and of the Satellite Tokamak Programme (STP), members of the National Institute of Informatics (NII) and the National Institute for Fusion Science (NIFS) in Japan, and members of JET and WEST in Europe. In this paper, we report on the results of the REC verification tests that have been carried out in 2017. These tests were mainly aimed at assessing the functionalities of the REC control room (i.e., the configurability of the room layout, the capabilities of the video wall, etc.), as well as the functionalities of the software tools for remote participation that have been developed during the first BA period. A report on the preliminary remote participation tests carried out in collaboration with the JET tokamak will be also given, together with a description of the tests with both JET and WEST that have been planned for 2018.

Speaker: Dr Susana Clement Lorenzo (Fusion for Energy)

162 Visual Servo of Tokamak Relevant Remote Handling Systems using Neural Network Architecture

Tokamak inspection and maintenance requires different Remote Handling (RH) systems such as long reach planar manipulators, multi-DOF hyper-redundant arms etc. As no structural support can be provided inside the tokamak, these RH systems are usually cantilevered and have a number of articulations to traverse the toroidal geometry of the tokamak. The kinematic configuration is thus different for conventional manipulators. Due to long cantilevered length, heavy payload handling, structural deformations, gearbox backlash and control system inaccuracies the final pose of the end effector may vary from the desired pose when only a servo feedback loop is used. Such inaccuracies can only be eliminated by using Visual Servo (VS) technique, where the inverse kinematics and trajectory planning are done based on visual feedback from cameras mounted on the RH system. The paper gives a fresh approach to visual servo for tokamak RH systems using artificial neural networks (NN) architecture. A multi-layered feed-forward NN is trained using the joint angle vector as input and the corresponding feature vector(s) of markers in a sample tile as output. The trained NN can thus predict the joint configurations for given features vectors. This eliminates the requirement of closed-form inverse kinematic solution of the manipulator and camera calibration. The NN architecture and proposed controller are validated and presented using simulation on 5DOF remote handling manipulator. Real time implementation methodology for NN based controller are also discussed.

Speaker: Mr Pramit Dutta (Institute for Plasma Research)

Summary_Visual Servo.pdf

10:15 Coffee Break

EX/1-TH/1 Energetic Particles

163 Strongly non-linear energetic particle dynamics in ASDEX Upgrade scenarios with core impurity accumulation

In 2017 a new scenario on ASDEX Upgrade for the dedicated investigation of energetic particle (EP) physics has been developed. This scenario is unique in two aspects: firstly, the neutral beam (NB) induced fast-ion beta is comparable to the background plasma β, and secondly, the ratio of the fast ion energy to the thermal background is of the order 100. At ASDEX Upgrade we reach this previously unexplored regime by NB off-axis heating only and by letting impurities accumulate in the core. Due to strong radiation losses the background tempera- tures and pressures of both ions and electrons stay low, despite 2.5 − 5MW NB heating. In the stable flattopphaseanunprecedentednumberofvariousEP-driveninstabilities(despitevEP/vAlfvén ≈0.4≪ 1) is simultaneously observed: EP-driven geodesic acoustic modes (EGAMs), beta-induced Alfvén eigenmodes (BAEs), reversed shear Alfvén eigenmodes (RSAEs) and toroidal Alfvén eigenmodes (TAEs), that are modulated by transient q = 2 sawtooth-like crashes, NTMs and ELMs. The physics reasons for these strong mode activity are discussed. During the stable flat-top phase meaningful EP distribution function measurements (FIDA) and analysis (TRANSP/FIDASIM) can be performed. First results indicate that the EP profiles differ significantly from neoclassical predictions. Bicoherence analysis using an advanced toolset for non-stationary processes reveals that non-linear coupling processes between different frequency bands exist. In addition, TAE bursts are observed to trigger the onset of EGAMs which indicates coupling of these modes via the velocity space (EP avalanches). Linear and non-linear tools (HAGIS/LIGKA, ORB5, XHMGC) are used for mod- eling mode onset and non-linear phases. These experiments facilitate the experimental study of the interaction of AEs, zonal modes and turbulence and thus serve as an ideal validation opportu- nity for various non-linear analytical and numerical models. In addition, the observed onset of EP avalanches can be quantified. The investigation and understanding of these - so far not accessible - physics elements is a prerequisite for a reliable prediction of the self-organisation of a burning plasma.

Speaker: Dr Philipp Lauber (IPP Garching)

2018_IAEA_FEC_India_poster_v2.pdf

2018_IAEA_FEC_Lauber_talk_169.pdf

2018_IAEA_FEC_Lauber_v4.pdf

summary slide 2018_IAEA_Lauber_Summary.pdf 2018_IAEA_Lauber_Summary.pptx

164 Simulations of energetic particle driven instabilities and fast particle redistribution in EAST tokamak

Instabilities driven by energetic particles including fishbones and Alfven eigenmodes, together with fast particle loss and redistribution due to resonant magnetic perturbations (RMPs), have been investigated numerically with codes M3D-K, MEGA, and GYCAVA in EAST tokamak. Firstly, hybrid simulations with the global kinetic-magnetohydrodynamic (MHD) code M3D-K have been carried out to investigate the beam-driven fishbone in EAST experiment. The results are consistent with the experimental measurement with respect to mode frequency and mode structure. Nonlinear simulations show that the frequency of the fishbone chirps up and down with corresponding hole-clump structures in phase space, consistent with the Berk-Breizman theory. In addition to the low frequency fishbone, a high frequency beta-induced Alfven eigenmode (BAE) is excited during the nonlinear evolution. Secondly, two kinetic-MHD codes, namely MEGA and M3D-K, have been applied to study fast ion driven toroidal Alfven eigenmodes (TAEs) in EAST tokamak. Parameter scans show that the frequency and growth rate of TAEs simulated by the two codes agree well with each other. The analysis of the resonant interaction between the TAE and fast ions shows that the TAE exchanges energy with the co-current passing particles with parallel velocity $|v_∥ |≈V_{A0}/3$ or $|v_∥ |≈V_{A0}/5$, where $V_{A0}$ is the Alfven speed on the magnetic axis. Moreover, the TAE destabilized by the counter-current passing ions has much smaller growth rate than that driven by the co-current ion. Thirdly, the effects of RMPs on the loss and redistribution of passing ions are investigated numerically by the orbit following code GYCAVA for EAST tokamak. The loss fraction and the loss region of passing ions increase with the amplitude of RMPs. For the energetic passing ions, the extra loss induced by RMPs can be comparable to the loss induced by the magnetic drift. The extra loss of passing ions induced by RMPs is related to the drift island structure induced by RMPs and the magnetic drift, and the stochasticity induced by overlap of magnetic islands. The dependence of the loss fraction and loss region on the toroidal mode number of RMPs is related to the safety factor. Finally, the pitch angle and energy of particle can impact the loss of energetic passing ions. These results would provide guidance for future EAST experiments.

Speaker: Dr Wei Shen (Institute of Plasma Physics, Chinese Academy of Sciences)

presentation.pdf

presentation.pptx

Summary Slides

165 Reduced energetic particle transport models enable comprehensive time-dependent tokamak simulations

The inclusion of the reduced-physics energetic particle (EP) *kick model* for EP transport in TRANSP has resulted in a dramatic improvement of interpretive and predictive capabilities for time-dependent tokamak simulations including the effects of EP transport by instabilities. The kick model has recovered the measured toroidal Alfvén eigenmode (TAE) spectrum on NSTX-U and has reproduced details of the fast ion diagnostic data measured on DIII-D for EP modes and tearing modes. Being able to predict the occurrence and effect of those instabilities is one of the grand challenges for fusion and a necessary step to mitigate their negative effects. The kick model has proven the potential of phase-space resolved EP simulations to unravel details of EP transport for detailed theory/experiment comparison and for scenario planning based on optimization of NBI parameters. Work is also ongoing to complement the kick model approach with the RBQ1D model based on the resonance-broadening quasi-linear theory to develop a self-consistent, numerically efficient predictive EP transport model. On NSTX-U, the kick model successfully reproduces the stability of co- and counter-propagating TAEs driven unstable by NB injection. The model successfully reproduces the transition from a co-TAE dominated scenario to one with coexhisting co- and counter-TAEs. Based on the analysis, strategies for mitigating the instabilities are developed through TRANSP by varying the NB injection parameters. The phase space resolution implemented in the model is also crucial for its successful validation against fast ion diagnostics data from Fast Ion D-Alpha (FIDA) and neutral particle analyzers (NPA). For DIII-D discharges with strong Alfvénic activity, the amplitude of the instabilities used in the simulation is first adjusted to match the measured neutron rate. The inferred FIDA and NPA signals based on the simulation are then compared with the experimental data for validation, showing excellent agreement. Initial analysis via the RBQ1D model gives similar results, indicating its potential for predictive simulations. Enhancements to TRANSP via the inclusion of reduced EP transport models are playing an important role in scenario development including realistic treatment of fast ion transport by instabilities, e.g. to optimize the scenario by tailoring NB injection power and voltage.

Speaker: Dr Mario Podesta (Princeton Plasma Physics Laboratory)

Podesta.M-EX1-2.Summary-slide.pptx

podesta.M-EX1-2_v1.pptx

166 Critical fast ion distribution in phase space for the synchronized sudden growth of multiple Alfvén eigenmodes and the global transport of fast ions

Alfvén eigenmodes (AEs) driven by fast ions in tokamak plasmas and the fast ion distribution formed with the AEs, neutral beam injection (NBI), and collisions are investigated with hybrid simulations for energetic particles and a magnetohydrodynamic (MHD) fluid [1]. The multi-phase simulation [2], which is a combination of classical simulation and hybrid simulation, was applied for various beam deposition power (P_NBI) and slowing-down time (t_s). In the classical simulation, energetic particle orbits are followed in the equilibrium magnetic field with NBI and collisions while the MHD perturbations are turned off. The physical parameters other than P_NBI and t_s are similar to those of a TFTR experiment [3]. For P_NBI=10MW and t_s=100ms, which are similar to the TFTR experiment, the AE bursts take place with a time interval 2.7ms and the maximum amplitude of radial MHD velocity normalized by the Alfvén velocity vr/vA=3x10^-3, which are close to the TFTR experiment. With increasing volume-averaged classical fast ion pressure, the fast ion confinement degrades monotonically due to the transport by the AEs. The fast ion pressure profile resiliency, where the increase in fast ion pressure profile is saturated, is found for the cases with the AE bursts. In this work, we have clarified the physical process of the AE burst in toroidal plasmas. Before the AE bursts occur, multiple AEs become unstable, and grow to low amplitude. The low-amplitude AEs gradually and locally flatten the fast ion distribution in phase space leading to the formation of a stepwise distribution. The stepwise distribution is a “critical distribution” where the further beam injection leads to the higher AE amplitude, the broadening of the locally flattened regions, and their overlap. This resonance overlap of the multiple AEs [4] brings about the AE burst, the global transport of fast ions, and the saturation of the distribution. [1] Y. Todo, New J. Phys. 18 (2016) 115005. [2] Y. Todo et al., Nucl. Fusion 54 (2014) 104012. [3] K. L. Wong et al., Phys. Rev. Lett. 66 (1991) 1874. [4] H. L. Berk, B. N. Breizman, and M. Pekker, Phys. Plasmas 2 (1995) 3007.

Speaker: Dr Yasushi Todo (National Institute for Fusion Science)

Summary_TH1-2_Todo_v1.pdf

Todo-FEC20181023v4.pdf

167 Impact of ECH/ECCD on Fast-ion-driven MHD Instabilities in Helical Plasmas & Excitation mechanism of the energetic particle driven resistive interchange mode and strategy to control the mode in Large Helical Device

A. We discuss the effect of electron cyclotron heating (ECH) and current drive (ECCD) on fast particle (FP)-driven MHD instabilities in stellarator/heliotron (S/H) plasmas obtained in LHD, Heliotron J and TJ-II. We demonstrate that FP-driven MHD instabilities including energetic particle modes (EPMs) and Alfvén eigenmodes (AEs) can be controlled by means of magnetic shear s modified by EC-driven plasma current. EPMs can be controlled by changing continuum damping rate, which is the main damping mechanism of the EPM and depends on s. AEs are significantly affected by the change of structure of the shear Alfvén continuum which can be modified by s. We also find that ECH (non-ECCD) can impact FP-driven MHD instabilities. Candidates to explain the ECH effect on FP-driven MHD instabilities are the variation in the fast ion profile and/or the trapped electron collisional damping. B. The helically-trapped energetic-particle (EP) driven resistive interchange mode (EIC) observed in the Large Helical Device (LHD) causes large amount loss of EPs. It is destabilized when the precession motion of the helically trapped EP resonates with the pressure driven mode. A velocity modulation caused by the toroidicity of the magnetic field produces this resonance. Strategy and the initial results to suppress the EIC mode based on the knowledge of the EP orbit effects, by the ECH heating and by the RMP application, are presented. EPs having perpendicular velocity components are trapped in the weak magnetic field region of the LHD and making precession motion helically. The rotation frequency of this precession motion is slow enough to interact with the pressure driven MHD modes. If the energy transfer from the EP to the mode is estimated by evaluating the correlation of the fluctuating component of the precession motion and the MHD mode, a resonance is found when the MHD mode rotates poloidally -1.2 times of the poloidal component of the heliccally trapped EP motion. This resonance disucssed here is consistent with the following observations found in the hydrogen / deuterium experimental campaign. 1) MHD mode rotates in the electron diamagnetic drift direction while the EP moves in the ion diamagnetic drift direction. 2) The mode frequency is almost the same with the precession frequence of the initial velocity of the NB-injected EPs. The EIC modes are succesufully suppressed by the ECH injection and RMP application. The physical mechnism of the stabilization will be discussed.

Speaker: Dr Satoshi Yamamoto (Institute of Advanced Energy, Kyoto University)

oral presentation 181022_iaea-fec18_talk_ex1-3R.pdf

Summary Slides 180927_iaea-fec18_ss_v1.pdf

168 Excitation mechanism of the energetic particle driven resistive interchange mode and strategy to control the mode in Large Helical Device

The helically-trapped energetic-particle (EP) driven resistive interchange mode (EIC) observed in the Large Helical Device (LHD) causes large amount loss of EPs. It is destabilized when the precession motion of the helically trapped EP resonates with the pressure driven mode. A velocity modulation caused by the toroidicity of the magnetic field produces this resonance. Strategy and the initial results to suppress the EIC mode based on the knowledge of the EP orbit effects, by the ECH heating and by the RMP application, are presented. EPs having perpendicular velocity components are trapped in the weak magnetic field region of the LHD and making precession motion helically. The rotation frequency of this precession motion is slow enough to interact with the pressure driven MHD modes. If the energy transfer from the EP to the mode is estimated by evaluating the correlation of the fluctuating component of the precession motion and the MHD mode, a resonance is found when the MHD mode rotates poloidally -1.2 times of the poloidal component of the heliccally trapped EP motion. This resonance disucssed here is consistent with the following observations found in the hydrogen / deuterium experimental campaign. 1) MHD mode rotates in the electron diamagnetic drift direction while the EP moves in the ion diamagnetic drift direction. 2) The mode frequency is almost the same with the precession frequence of the initial velocity of the NB-injected EPs. The EIC modes are succesufully suppressed by the ECH injection and RMP application. The physical mechnism of the stabilization will be discussed.

Speaker: Dr Satoshi Yamamoto (Institute of Advanced Energy, Kyoto University)

onepage.pdf

12:30 Lunch

EX/1-TH/1 P2 Posters

169 Critical fast ion distribution in phase space for the synchronized sudden growth of multiple Alfvén eigenmodes and the global transport of fast ions

Speaker: Dr Yasushi Todo (National Institute for Fusion Science)

170 Excitation mechanism of the energetic particle driven resistive interchange mode and strategy to control the mode in Large Helical Device

Speaker: Dr Satoshi Ohdachi (National Institute for Fusion Science)

onepage.pdf

171 Impact of ECH/ECCD on Fast-ion-driven MHD Instabilities in Helical Plasmas

Speaker: Dr Satoshi Yamamoto (Institute of Advanced Energy, Kyoto University)

172 Reduced energetic particle transport models enable comprehensive time-dependent tokamak simulations

Speaker: Dr Mario Podesta (Princeton Plasma Physics Laboratory)

Podesta.M-EX1-2.Summary-slide.pptx

173 Simulations of energetic particle driven instabilities and fast particle redistribution in EAST tokamak

Speaker: Dr Wei Shen (Institute of Plasma Physics, Chinese Academy of Sciences)

Summary Slides

174 Strongly non-linear energetic particle dynamics in ASDEX Upgrade scenarios with core impurity accumulation

Speaker: Dr Philipp Lauber (IPP Garching)

OV/4 Overview Magnetic Fusion

175 Overview of first Wendelstein 7-X high-performance operation with island divertor

The optimized superconducting stellarator device Wendelstein 7-X restarted operation after the assembly of a graphite heat shield and an inertially cooled island divertor. This paper reports on results from the first high-performance plasma operation. Plasma densities of $1-4\cdot 10^{19}\,\mathrm{m}^{-3}$ with electron temperature $5-10\,\mathrm{keV}$ were routinely achieved with hydrogen gas fuelling, eventually terminated by a radiative collapse. Up to $1.4\cdot 10^{20}\,\mathrm{m}^{-3}$ plasma density was reached with repetitive hydrogen pellet injection. Here, the ions are indirectly heated, and at a density of $8\cdot 10^{19}\,\mathrm{m}^{-3}$ temperatures $T_e\simeq T_i = 3.4\,\mathrm{keV}$ were accomplished, which corresponds to $nT\tau_E = 6.4\cdot 10^{19}\,\mathrm{keVs/m}$ with peak diamagnetic energy $1.1\,\mathrm{MJ}$. Stable $25\,\mathrm{s}$ long-pulse helium discharges with $2-3\,\mathrm{M}$W ECRH power and up to $75\,\mathrm{MJ}$ injected energy were created routinely for equilibrium and divertor load studies, with plasma densities around $5\cdot 10^{19}\,\mathrm{m}^{-3}$ and $5\,\mathrm{keV}$ electron temperature. The divertor heat loads remained far below the limits. The O/C impurity concentration ratio has decreased in comparison to the previous limiter operation and no intrinsic impurity accumulation along with high edge radiation were observed in stationary plasmas. During pellet-fuelled hydrogen discharges, full detachment was observed with divertor target heat flux reduction by more than $\times 10$. Both X2 and O2 mode ECRH schemes were applied and electron cyclotron current drive (ECCD) experiments were conducted. During co-ECCD injection experiments with axial currents up to $13\,\mathrm{kA}$, frequent fast crashes were observed mainly in the core electron temperature, suggesting a fast magnetic reconnection mechanism. The radial electric field measured with (Doppler) and correlation reflectometry changes sign at the plasma edge from $+10\ldots+20\,\mathrm{kV/m}$ to $-10\ldots-5\,\mathrm{kV/m}$, fairly independent of discharge parameters and heating power. Edge and scrape-off layer turbulence was measured with both Langmuir probes and reflectometer diagnostics. Core turbulence was measured with a phase contrast imaging diagnostic and different levels of broad band turbulence as well as coherent Alfvén mode activity were observed.

Speaker: Prof. Thomas Klinger (Max-Planck Institute for Plasma Physics)

IAEA 2018 W7-X Overview Klinger.pptx

176 Overview of the First Deuterium Experiment in LHD

In the first deuterium (D) experiment, LHD established one of the most important milestones towards the realization of the helical fusion reactor, ion temperature Ti of ~ 10 keV. This is the highest record among stellarator/heliotron devices. Clear reduction of the ion thermal diffusivity in both core and edge regions in D discharge from hydrogen (H) was identified, indicating the effect of the isotope mass. This experimental result was supported by the initial results from gyrokinetic simulations including multi-species of ion. By measuring the neutron flux from D plasma, energetic particle (EP) behavior trapped in the helical ripple could directly be estimated, which is quite important for heliotron devices, because demonstration of the EP confinement is essential to realize the burning condition. Precise measurement of the tritium exhaust demonstrated the tritium mass balance including the evacuation system.

Speaker: Dr Tomohiro Morisaki (National Institute for Fusion Science)

OV4-2_Morisaki.pdf

OV4-2_Morisaki.pptx

OV4-2_Morisaki_presentation.pptx

177 Overview of TJ-II stellarator results

The flexibility of TJ-II together with its unique plasma diagnostics makes it an ideal laboratory to study the relationship between magnetic topology, electric fields, transport and model validation. **Zonal flows and heat transport.** HIBP measurements of zonal electrostatic potential relaxation are consistent with EUTERPE gyrokinetic (GK) simulations. The width of the oscillating zonal flow (ZF) radial electric field (Er) structures depends on its frequency. Additional GK simulations predict the localization of density fluctuations, in line with Doppler Reflectometry (DR) measurements. Transfer Entropy technique-based analyses shows that transport is not smooth and continuous but rather occurs in a stepwise fashion. **Impurity and particle dynamics**. Neoclassical (NC) theory results show how a negative Er field can coexist with an outward impurity flux. Flux-surface variations of electrostatic potential can have a significant impact on high-Z impurity radial fluxes. Probe measurements of plasma potential asymmetries on magnetic flux surfaces and DR measurements of poloidal asymmetries in Er fields, are consistent with NC simulations. Plasma core fuelling experiments with pellets show that the radial redistribution of particles can be understood qualitatively from NC predictions. Thermal neutrals react to low frequency plasma fluctuations. **NC and turbulent transport**. Zero frequency Er fields as well as low frequency ZF-like global oscillations have been identified during the Low to High (L-H) transition in H and D plasmas. No evidence of the isotope effect was observed in the L-H transition. **Power-exhaust physics.** The TJ-II programme on liquid metals address fundamental issues such as the self-screening effect driven by liquid lithium evaporation and the tritium inventory control. **Stellarator optimization**. Explicit expressions for the radial NC fluxes have been calculated in low collisionality regimes and have been included in a numerical code to deal with magnetic configurations close to omnigeneity. The relaxation of the constraint of periodicity imposed by the external confining magnetic field coils in a Helias configuration produces weak periodicity-breaking deformations of the plasma. The conditions of quasi-isodynamicity are not significantly altered by the periodicity-breaking distortions.

Speaker: Dr Enrique Ascasibar (CIEMAT)

20181023_OV_TJ-II_6.pdf

178 ELM and ELM-control Simulations

Future devices like JT-60SA, ITER and DEMO require quantitative predictions of pedestal density and temperature levels, as well as divertor heat fluxes, to improve global confinement capabilities while preventing divertor erosion/melting in the planning of future experiments. Such predictions can be obtained from non-linear MHD codes like JOREK, for which systematic validation against current experiments is necessary. In this paper, we show the validation of ELM simulations with JOREK using quantitative comparison against JT-60U experiments. Note this is the first JOREK validation of ELM simulations at exact Spitzer resistivity. In addition, we demonstrate the essential importance of the separatrix position, required for a successful agreement with experimental data. On the basis of this validation, we propose estimates of ELM size, ELM-induced divertor heat-fluxes, and pre-ELM pedestal pressure, for future JT-60SA scenarios.

Speaker: Dr Stanislas Pamela (CCFE - UKAEA)

SPamela_Summary_Slide.pdf

179 Experiments in Disruption Avoidance for ITER Using Passive and Active Control

Key plasma physics and real-time control elements needed for robustly stable operation of high fusion power discharges in ITER have been demonstrated in US fusion research. Optimization of the current density profile has enabled passively stable operation without n=1 tearing modes in discharges simulating ITER’s baseline scenario with zero external torque. Stable rampdown of the discharge has been achieved with ITER-like scaled current ramp rates, while maintaining an X-point configuration. Significant advances have been made toward real-time prediction of disruptions: machine learning techniques for prediction of disruptions have achieved 90% accuracy in offline analysis, and direct probing of ideal and resistive plasma stability using 3D magnetic perturbations has shown a rising plasma response before the onset of a tearing mode. Active stability control contributes to prevention of disruptions, including direct stabilization of resistive-wall kink modes in high beta discharges, forced rotation of magnetic islands to prevent wall locking, and localized heating/current drive to shrink the islands. These elements are being integrated into stable operating scenarios and a new event-handling system for off-normal events in order to develop the physics basis and techniques for robust control in ITER.

Work supported by US DOE under DE-FC02-04ER54698, DE-SC0008520, DE-SC0016372, DE-FG02-04ER54761, DE-AC52-07NA27344, DE-SC0015878, DE-SC0014264, DE-FG02-99ER54524, DE-FOA-0001498, DE-AC02-09CH11466, DE-FC02-99ER54512, DE-SC0010720, DE-SC0010492, and the DOE Computational Science Graduate Fellowship, and by the EUROfusion Consortium with funding through FuseNet from the Euratom research and training programme 2014-2018 under Grant Agreement No. 633053. The views and opinions expressed herein do not necessarily reflect those of the European Commission.

Speaker: Dr Edward Strait (General Atomics)

Strait OV4-5.pdf

P2 Posters

180 A promising grassy ELM regime for high-performance steady-state operations with metal wall in EAST and CFETR

A highly reproducible stationary grassy ELM regime has been achieved in the EAST superconducting tokamak with water-cooled metal wall, exhibiting good energy confinement, H_98y2~1.1, strong tungsten impurity exhaust, and compatibility with low rotation, high density and fully non-inductive operations. It offers thus a highly promising operational regime in EAST, potentially applicable to future steady-state tokamak fusion reactors, such as the Chinese Fusion Engineering Test Reactor (CFETR). Recent linear and nonlinear simulations using ELITE and BOUT++ codes have uncovered, for the first time, the underlying physics of this grassy ELM regime. Both grassy and type-I ELMs are triggered by the marginally unstable intermediate-n peeling-ballooning modes (PBMs). However, the radial width of the linear mode structures cannot explain the small ELM size. The nonlinear simulations indicate that the pedestal current-profile relaxation is much slower than the pressure-gradient collapse. For the type-I ELMs, the high current density and gradient can still drive the kink/peeling-dominated low-n PBMs unstable even when the pressure gradient is significantly reduced, thus the collapsing front propagates radially inward, leading to large ELMs, as observed by Lithium BES on EAST. In contrast, for grassy ELMs, the pedestal current density and gradient are inherently lower and the operational parameter space can intrinsically improve the pedestal stability against the low-n PBMs. Hence, the instabilities quickly die away when the pressure gradient is just slightly reduced, leading to small ELMs. Some important features of the EAST grassy ELM regime are expected in future steady-state reactor-level plasmas, such as the relatively lower pedestal density gradient, higher SOL density and wider pedestal at high betap and low rotation. The desired edge density profile can be self-consistently generated by the strong cross-field particle transport driven by the high-frequency grassy ELMs. In particular, the pedestal density gradient in reactor-level plasmas could be even lower, since the plasma temperature and density at the separatrix are high so that the penetration of recycling neutrals into the pedestal is almost negligible. This may facilitate access to the grassy ELM regime in future devices, thus opening a potentially new avenue for next-step steady-state fusion development.

Speaker: Dr Guosheng Xu (Institute of Plasma Physics, Chinese Academy of Sciences)

XuEXP2-4SummarySlide.pptx

181 A Transmission Electron Microscopy Investigation of Defects Induced in Tungsten Foils by Gold (Au) and Boron (B) Ion Irradiation

Tungsten is a promising candidate for first-wall material in fusion reactors and its use as a plasma-facing material is being investigated in both tokamaks as well as laboratory experiments [1, 2]. In fusion environment tungsten will be exposed to neutron, helium and hydrogen isotope implantation along with the heat flux which will lead to material damage. Irradiation by charged particles such as H, D, T, He, Au, W etc. is employed to surrogate the experiment of high energy and high flux neutron irradiation in tungsten. Present work concerns the study of ion mass in meso-scale defects created in tungsten using Transmission Electron Microscopy (TEM) after irradiated by (1) high energy heavy mass gold (Au of 80MeV) and (2) low mass boron (B of 10MeV) ions with a fluence of 1.3x1014 cm-2. Prior to irradiation tungsten foil samples of 100 µm thickness (99.96 % pure), procured from Princeton scientific corp. USA, and were recrystallized at 1838 K under 10-3 mbar base pressure in 200 mbar Ar+ 8% H2 environment. Defects created by Au and B ions irradiation in the recrystallized foil were characterized for the types of defect such as defect clusters, dislocation lines, loops etc., and are quantified in terms of dislocation line length, dislocation loop size and their densities using transmission electron microscopy. The small defect clusters in Au irradiated samples and dislocations segments and dislocation loops were observed in B irradiated samples. Furthermore, the Au ion irradiation has led to the formation of dislocation lines density lesser than that of B irradiated foil. [1] E. E. Bloom, Structural Materials For Fusion Reactors, Nuclear Fusion, 30, (9), 1879-1896, 1990. [2] M . Rubel, Structure Materials in Fusion Reactors: Issues Related to Tritium, Radioactivity and Radiation-Induced Effects, Transactions of Fusion Science and Technology, 53, 459-467, 2008.

Speaker: Dr Prashant Sharma (ITER-India, IPR Gandhinagar)

Presentation summary.pdf

182 Advanced energetic ion and impurity ion physics in 2D and 3D magnetically confined plasmas

The VENUS-LEVIS code [D. Pfefferle, *et al*, Compt. Phys. Communs. **185**, 3127 (2014)] has been optimised for full orbit and guiding centre simulations in fully 3D electromagnetic fields. Curvilinear flux coordinate systems are deployed, with analytic (Fourier) representation of the fields for accurate simulation over slowing down time scales of fast particles and heavy impurities. An important recent application includes the viability of ICRH [J. Faustin, *et al*, Nucl. Fus. **56**, 092006 (2016)] and synergetic NBI-ICRH in Wendelstein-7X. Optimisation of fast ion generation and core heating is identified via variation of magnetic configuration, and methods of heating and associated properties (e.g. 3-ion species heating, minority heating, ICRH heating of NBI minority ions etc). Higher harmonic ICRH is a recent upgrade of the SCENIC ICRH package [M. Jucker, *et al*, Comp. Phys. Commun. **182**, 912 (2011)] that will permit various heating scenarios to be validated in advance of experiments. Recent updates to the VENUS-LEVIS code include higher order drift effects [S. Lanthaler, et al, Plasma Phys. Control. Fusion 59, 044014, (2017)], and advanced switching between full orbit and higher order drift orbit approximation during particle motion, as required in order to maintain accuracy and numerical efficiency. Applied for example to the current European DEMO design it is found that the magnetic ripple associated with 16 toroidal field coils has a weak affect on the radial transport of alpha particles, increasing the power flux due solely to prompt losses by a factor of about two. In addition, higher order guiding centre modelling has facilitated implementation of a 5 1/2D ICRH modelling scheme into SCENIC, which has many advantages over the standard quasi-linear operator approach. The VENUS-LEVIS code has also been updated [M. Raghunathan, *et al*, Plasma Phys. Control. Fusion **59**, 124002 (2018)] to include strong toroidal plasma rotation and the neoclassical effect of collisions in the frame of the diamagnetic flows of thermal ions in three dimensions. This upgrade has been applied to the transport of tungsten in JET hybrid scenarios susceptible to *m=n=1* continuous modes. Neoclassical collisional transport effects in 3D rotating magnetic fields can cause strong core accumulation of tungsten.

Speaker: Dr Jonathan Graves (Ecole Polytechnique Federale de Lausanne (EPFL), Swiss Plasma Center (SPC), CH-1015 Lausanne, Switzerland)

graves_IAEA_TH_P2_14_summary.pdf

183 Advances in Plasma-Wall Interaction Control for H-mode Operation over 100s with ITER-like Tungsten Divertor on EAST

Managing excessively high divertor power and particle fluxes and related plasma-wall interactions (PWI) is one of the most critical issues for the steady-state operation of the EAST superconducting tokamak and future fusion devices, such as ITER and CFETR. A world record long pulse H-mode operation of 101.2 seconds with H_98=1.1 and total power injection of 0.3 GJ has been successfully achieved in EAST with ITER-like top tungsten (W) divertor, which has steady-state power exhaust capability of 10 MWm-2. The peak temperature of W target T≈500 oC and a heat flux ≈3 MWm-2 was maintained stably. Great efforts have been made to simultaneously control peak heat flux and particle/impurity exhaust towards the long pulse of 100 s time scale. Particle exhaust was optimized by preferentially directing the plasma flow toward the outer target with the ion Bx∇B drift away from the W divertor and improving divertor pumping with the top cryo-pump. Effective power dispersal was achieved by tailoring the three dimensional (3D) divertor plasma footprint using lower hybrid wave (LHW) through induced edge magnetic topology change and broadened plasma wetted area, thus reducing peak heat flux and W sputtering. Extensive lithium coating was employed to lower edge recycling, low-Z impurity content and W sputtering. In addition, divertor detachment in H-mode for PWI handling was achieved for the first time with W divertor in EAST. Compared with previous L-mode in EAST, in H-mode the detachment has a higher density threshold with n_e/n_G~ 0.65. Active feedback control of radiative divertor with neon impurity seeding was successfully achieved with f_rad ~ 18 - 36%, and a slight loss of plasma stored energy ~ 7-11%, offering a promising technique for steady-state divertor radiation and heat flux control. The upgrade plan and status of EAST bottom divertor from graphite to water-cooled W to accommodate more challenging PWI for steady-state H-mode over 400 s and L-mode operation over 1000 s will also be presented.

Speaker: Dr Liang Wang (Institute of Plasma Physics, Chinese Academy of Sciences (ASIPP))

EX P2-8 summary slide.pptx

184 Analysis of energetic particle driven toroidal Alfven eigenmodes in CFETR baseline scenario

For burning plasmas in fusion reactors, Energetic Particles (EP) generated from plasma heating and D-T reaction can destabilize Alfven Eigenmodes (AE). Alfven eigenmodes can conversely induce transport and loss of energetic particles. It is one of the crucial issues to study the interaction between EPs and AEs for CFETR (China Fusion Engineering Test Reactor). Eigenanalysis of AEs in CFETR baseline scenario is taken by using AWEAC (Alfven Wave Eigen-Analysis Code), a developing code similar to NOVA/NOVA-k but dealing with asymmetric configuration of tokamaks. Linear simulations of TAEs driven by EPs are performed using the hybrid-kinetic MHD module in the NIMROD code. This HK-MHD module includes the kinetic effects of EPs through the coupling between a δf particle-in-cell (PIC) model for EPs and the 3D MHD model for the bulk plasma. The CFETR equilibrium used is obtained from the EFIT code based on self-consistent core-pedestal coupled OMFIT workflow. The “slowing down” distribution is used to model the equilibrium distribution of energetic ions from α particles produced by fusion. The frequency of TAEs generated by EPs in NIMROD simulation are consistent with the eigen-analysis results from AWEAC, which are within the range 40-100 kHz. For TAEs/EPMs driven by α particle from D-T fusion, the growth rate increases with both the toroidal mode number and EP beta fraction. Global 2D twist structures of TAEs/EPMs in CFETR baseline scenario, especially RSAE (Reverse Shear Alfven eigenmode) structure for some cases, are obtained for the first time using NIMROD. These results may be helpful for the future design of CFETR operations. Acknowledgments: This work is supported by the National Magnetic Confinement Fusion Science Program of China grant Nos. 2014GB124002 and 2015GB101004, and by the Natural Science Foundation of China grant No. 11205194. One of the authors P. Zhu also acknowledges the supports from U.S. DOE grant Nos. DE-FG02-86ER53218 and DE-FC02-08ER54975. This research used the computing resources from the Supercomputing Center of University of Science and Technology of China, the National Energy Research Scientific Computing Center in US, and local clusters in USTC, such as HPC, Lenovo, Inspur, and HWC.

Speaker: Dr Yawei Hou (University of Science and Technology of China)

Slide_Hou20180312.pdf

185 Burning Plasma Simulation with Alpha-Particle Heating

To achieve self-sustained ignited operation in a high energy Tokamak, it is important to understand and maximize the energy confinement time, which falls in the domain of transport theory. To analyze and understand dynamics of plasma in Tokamak, performing a one-dimensional transport simulation is still one of the best approaches. In our work we focus on burning plasma simulation and study the alpha particle heating in high energy Tokamaks like ITER. Transport simulations can be performed by solving 1D transport equations using codes such as LCPFCT (Laboratory for Computational Physics Flux-Corrected Transport)[1], which is used to solve 1D generalized coupled continuity, momentum and energy equations along with Maxwell’s equations. The transport equations are solved in flux coordinates by coupling with 2-D tokamak equilibrium. In this model, the effects of fusion reactions, coulomb collisional losses, radiation losses, alpha-heating, auxiliary heating and neo-classical Ware pinch are included. This will predict the performance of tokamak based fusion reactor for obtaining the steady state operation. This model is being developed and will be bench marked with published results. This will be use to predict the performance of SST2-like [2] and ITER-like [3] cases and results will be presented in this paper. References: [1] Boris, J.P.; A.M. Landsberg; E.S. Oran; and J.H. Gardner. 1993. "LCPFCT - A Flux-Corrected Transport Algorithm for Solving Generalized Continuity Equations." NRL Memorandum Report 93-7192. [2] R Srinivasan and the Indian DEMO Team, Fusion Engineering Design, 112 (2016) 240 [3] Progress in the ITER Physics Basis, Nuclear Fusion, 47 (2007)

Speaker: Mr Udaya Maurya (InIPR)

udaya_preprint_key_achievements.pdf

186 Characterization of Particle Growth and Enhancement of Sputtering Yields in a Co-generated Dusty Plasma

Most of the tokamaks including ITER, a significant part of the plasma-facing component including diverters, limiters, etc is comprised with graphite material. In the fusion plasma environment, the graphite gets bombarded by hydrogen and its isotope (deuterium and tritium) ions and erode graphite to a significant extent. Since such carbon particles can retain large amounts of hydrogen, dust contributes to the problem of inventory of radioactive tritium inside the fusion machine. Another impact of the dust particles in the operation of a fusion device is the possible degradation of the discharge performance. Such particles penetrating in the core plasma region can lead to discharge disruption. Thus, in order to perform successful fusion experiments it is important to assess and understand the processes by which dust is formed and by which it interacts with the fusion device and its plasma. Instead of understanding processes that exactly happen inside a fusion reactor, it is always better to match some aspects of graphite-hydrogen interaction in a plasma environment in small laboratory devices, and study the physical processes. To address some of this issues, we have performed an experiment to examine the particle growth and sputtering yields in a DC glow discharge plasma in between the graphite electrodes.

Speaker: Dr JYOTIRMOY PRAMANIK (DEPT OF PHYSICS, KHARAGPUR COLLEGE)

JPramanik_EXP2-9_SummarySlide.pdf

187 Comparison of energetic particle radial transport between single-n and multiple-n simulations of Alfvénic modes

The results of a set of simulations of Alfvén modes driven by an energetic particle population are presented, with the specific aim of comparing energetic particle radial transport between single-n and multiple-n simulations. The hybrid reduced O($\epsilon^3_0$) MHD gyrokinetic code HMGC is used, retaining both fluid (wave-wave) and energetic particles nonlinearities. The code HMGC retains self-consistently, in the time evolution, the wave spatial structures as modified by the energetic particle (EP) term.
A model equilibrium has been considered, rather than a specific experimental device, with the aim of studying how the dynamics of the EP driven Alfvénic modes changes when considering single-n or multiple-n simulations, while keeping all the other parameters fixed. A circular, shifted magnetic surface, static equilibrium has been considered, characterized by a large aspect ratio ($\epsilon_0= 0.1$) and a parabolic safety factor profile with $q_0=1.1$ and $q_a=1.9$ being, respectively, the on-axis and edge safety factor. A bulk ion density profile $n_i(r)$ ~ $(q_0/q(r))^{2}$ has also been assumed, in order to have the toroidal gap radially aligned, for all the mode considered. Regarding the EPs, an isotropic Maxwellian distribution function has been considered.
Simulations with toroidal mode numbers 1≤n≤15 have been considered. A variety of modes are observed (TAEs, upper and lower KTAEs, EPMs) during the linear growth phase. All the strongly unstable modes (4≤n≤12) exhibit pronounced (both up and down) frequency chirping at saturation. Nevertheless, no appreciable global modification of the energetic particle density profile is observed at saturation for the unstable modes.
On the contrary, multiple-n simulations, with the same Fourier toroidal mode spectrum of the set of single-n simulations, exhibit an appreciable broadening of the energetic particle radial density profile at saturation, thus showing an enhanced radial transport w.r.t. the single-n simulations. Moreover, the sub-dominant modes are strongly modified by the nonlinear coupling, which results both from the MHD and from the energetic particle terms. The present nonlinear simulations show that all the toroidal modes saturate almost simultaneously, after inducing an enhanced energetic particle radial transport. No evidence of the so-called "domino" effect is observed.

Speaker: Gregorio Vlad (ENEA, Fusion and Nuclear Safety Department, Frascati, Italy)

Summary-slide-G.Vlad-TH-P2-10.pdf

vlad-iaea2018-v0.pdf

188 Comprehensive magnetohydrodynamic hybrid simulations of fast ion losses due to the fast ion driven instabilities in the Large Helical Device

In the LHD, the fast ion confinement has been investigated by using three tangentially injected neutral beams (NBs) with 180 keV fast ions and/or two perpendicularly injected NBs with 40-80 keV fast ions. The Alfvén eigenmodes (AEs) are observed during the tangential-NB injections. The fast ion driven instabilities enhance the fast ion losses. It is important to identify the instabilities and clarify the properties of the lost fast ions due to the instabilities. A hybrid simulation code for nonlinear magnetohydrodynamics (MHD) and energetic-particle dynamics, MEGA, has been developed to simulate recurrent bursts of fast ion driven instabilities including the energetic-particle source, collisions and losses. In order to identify the instabilities and to clarify the process of the fast ion losses in the LHD experiments, MEGA is applied to the LHD plasmas, where fast ion driven instabilities and lost fast ion properties are investigated by using tangential-NBs, with the realistic conditions close to the experiments. In a plasma with tangential-injected neutral beams (NBs), the Alfvén eigenmode (AE) bursts with m/n=2/1 occur recurrently. As a result, the stored fast ion energy is saturated at a lower level than that of a classical slowing down calculation where the magnetohydrodynamic (MHD) perturbations are neglected. Fast ion losses occur during the AE bursts. The fast ion losses brought about by the AE bursts are proportional to the square of AE amplitude, which reproduces well the LHD experiment. This indicates the emergence of stochasticity in the fast ion loss process. The fast ions deposited well inside the plasma up to the magnetic axis are significantly lost for the counter-injected fast ions. We present the first self-consistent simulations that reproduce and clarify the fast ion loss properties in the LHD experiments.

Speaker: Dr RYOSUKE SEKI (National Institute for Fusion Science)

Summary Slides 1page.pptx

189 Design and Qualification of Precision Support Structure for Diagnostics

The ECE diagnostic is planned to be used for the measurements of plasma electron temperature profile with good spatial and temporal resolutions. Secondary objectives are to obtain information on non-thermal electron populations and the power loss due to ECE. One of the major requirements of ITER like Fusion Device is to study the plasma parameter to ascertain and control the fusion reaction. These diagnostic systems need to be assembled in the constrained space around the machines with tight tolerance for optical accuracy in many cases. The ECE diagnostic is planned to be used for the measurements of plasma electron temperature profile with good spatial and temporal resolutions. Secondary objectives are to obtain information on non-thermal electron populations and the power loss due to ECE. This diagnostics system has about 40m long multiple wave-guides to transmit the signal from the ITER Diagnostic building for data acquisition and assessment. For which the Design and qualification of Wave-guide Support Structure has been carried out. This paper elaborates on the Cost effective Design and Qualification of precision alignment cum support structures for the wave-guides which needs to be aligned accurately. The cost effective design has been developed using off the shelf components. This design reduces the ±25mm tolerances on the building to only ±0.5mm on the assembled wave-guide with sufficient stability. The Support Structure qualification has been done using the Design by analysis approach of the ASME code and the stresses are assessed using the ANSYS tool

Speaker: Mr Shrishail Padasalagi (ITER-India, IPR, HBNI)

IAEA- EXP2-25ECE DesignAndANALYSIS.pdf

190 E_rxB shear effect on cross phase mitigates ELM at high collisionality

A non-stationary, effective edge localized modes (ELMs) mitigation / suppression regime has been recently obtained by counter NBI heating at high collisionality on the Experimental Advanced Superconducting Tokamak (EAST). Our results show that counter NBI can significantly enhance the reversed toroidal rotation as well as the E_r×B flow shear of the pedestal. With the increased E_r×B flow shear, the ELM sizes can be suppressed by nearly 80%. The increased E_r×B flow shear can also broaden the power spectrum of the pedestal turbulence and enhance the amplitude of modes with high frequency (f>100kHz). The bispectrum study indicates that the nonlinear mode coupling of the pedestal turbulence also increases in counter NBI case, which can interrupt the linear growth of the peeling mode, thus leading to the suppression of ELM. When power of counter NBI is high enough, an ELM-free H mode can even be achieved on EAST. During the ELM-free H mode, the line averaged density as well as the amplitude of resistive ballooning mode keeps increasing until the H-L back transition. Those observations may link with the density limit in H mode discharge. BOUT++ simulations have been applied to study the characteristics of edge-localized mode at fixed high collisionality for different E_r structure. The simulation result reveals that the increased E_r×B shear suppresses the ELM size and delays the pedestal crash, which is consistent with the observations on EAST. Analysis of the cross-phase spectrum of potential and pressure perturbations indicates that the increased E_r×B shear can shorten the phase coherence time τ_c and flatten the spectrum of τ_c, which is and limited by nonlinear mode interaction. Thus, the peeling-ballooning mode doesn't get enough time to allow growth to large amplitude, which can be supported by the bispectrum study on EAST that increased ErxB flow shear can enhance the nonlinear interaction. Besides the collisionality, our simulations suggest a new way (Er shear) to control the ELM size, which is consistent with observed ELM suppression at larger E_r×B shear in high collisionality plasmas on EAST.

Speaker: Dr Defeng Kong (Institute of Plasma Physics Chinese Academy of Sciences)

IAEA_FEC2018_DFKONG.pptx

Manuscript_IAEA_FEC_DFKONG-20180926.pdf

191 Effect of Cathode Geometry on Magnetically Coupled Hollow Cathode Plasma Source

A direct current (dc) plasma source consisting of hollow cathode geometry and a constricted anode is presented. The effect of a hollow cathode geometry on radial density distribution of a magnetized plasma column has been studied in a low-pressure (approximately 1.4Pa) argon discharge. The plasma column is characterized using Langmuir probe and the radial density distribution for two different 'inside' profiles of a hollow cathode is discussed. Probe measurement indicates that conical-profile hollow cathode produces a plasma column with centrally peaked plasma density whereas cylindrical-profile hollow cathode forms plasma column with off-centered density peak. Thus overall dynamics of perpendicular and oblique cathode sheaths behind the sustenance of magnetized plasma column has been discussed. **Keywords:-** constricted anode, conical hollow cathode, cylindrical hollow cathode, Langmuir probe, magnetized plasma column, radial density distribution, oblique cathode sheaths.

Speaker: Mr Montu Bhuva (Institute for Plasma Research, INDIA)

192 Effect of the Controlled Density Gradient on Equilibrium and Confinement in a Simple Toroidal Device with two plasma sources

A simple toroidal device (SMT) is a toroidal device in which plasma is confined by the application of toroidal and vertical magnetic field only resulting in absence of a conventional effective rotational transform. Such devices provide a simple and well diagnosable test-bed for studies related to equilibrium, fluctuations and particle confinement for Tokamak edge. The device BETA at the Institute for Plasma Research (IPR) is one such SMT with a plasma major radius of 45 cm and minor radius of 15 cm and a maximum toroidal field of 0.1 Tesla. Quasi-static equilibrium in an SMT is controlled by the nature of fluctuation and flow [1, 2]. As observed in hot cathode discharges studied earlier [1, 2], density gradient provide fluctuation in the plasma and hence the instabilities [2]. Whereas radial electric field provides poloidal flow. Thus, the conditions are akin to Tokamak edge. To experimentally understand the effect of the density gradient, it is desirable to be able to control the local gradient at the outboard side by an additional plasma source. To this end, a new microwave source of frequency 2.4 GHz and power about 0.5 kW has been developed [3]. Hot cathode and microwave sources are used in tandem such that the upper hybrid resonance falls at the outboard density gradient region, which in turn allows us to control the density gradient locally. The details of the experiment will be presented. References [1] T. S. Goud, Thesis, Institute for Plasma Research, Gandhinagar, Gujarat, India (2012). [2] Umesh Kumar, Shekar G Thatipamula, R. Ganesh, Y. C. Saxena and D. Raju, Phys. Plasmas 23, 102301 (2016). [3] Umesh Kumar, R. Ganesh, K. Sathyanarayana, Y. C. Saxena, S. G. Thatipamula, D. Raju , Manuscript under preparation

Speaker: Mr Umesh Kumar (Institute for Plasma Research, Gandhinagar, Gujarat, India)

UmeshKumar_Summary_FEC2018.pdf

193 Experimental Study of Multi-scale Interaction between (Intermediate, Small)-scale Microturbulence and MHD modes in EAST Plasmas

Understanding plasma transport in phases with significant MHD activities (especially during plasma current ramp-up/down and disruption) in tokamak plasmas is crucial for predicting and thus controlling plasma behavior for future fusion devices, e.g. ITER. Since microturbulence plays an important role in driving anomalous plasma transport, the interactions between MHD modes and microturbulence is thought to be important in determining anomalous plasma transport [1]. Recent theoretical results in the literature show that microturbulence can nonlinearly interact with macro-instabilities such as kink/tearing mode through nonlinear cascade process or through temperature and/or density profile modulation from macro-instabilities. Due to the huge temporal and spatial scale separation between microturbulence and MHD modes, it is impossible for the present-day supercomputers to simulate their nonlinear interactions in a self-consistent way. In this talk, we present evidence of multi-scale interactions between (intermediate, small)-scale (kρ_i~2-6) microturbulence and MHD modes in EAST plasmas, including the first experimental identification of nonlinear coupling between microturbulence and an MHD mode during the current ramp-down phase in a set of L-mode plasmas in EAST [2] and the effects of 2/1 classical tearing mode on microturbulence [3] in the core of another set of EAST L mode plasmas using the EAST CO_2 laser collective scattering diagnostic in forward mode and far-forward mode. We demonstrate the nonlinear coupling between microturbulence and MHD mode with bispectral analysis [4] and envelope method [5], showing statistically significant bicoherence and modulated turbulent density fluctuation amplitudes correlated with the MHD mode. We also show that microturbulence spectral power is correlated to the 2/1 tearing mode and modulation effects on microturbulence by the 2/1 tearing mode. [1] P.J. Sun et al 2018 Nucl. Fusion 58 016003 [2] P.J. Sun et al 2018 Plasma Phys. Control. Fusion 60 025019 [3] Kim Y C and Powers E J 1979 IEEE Trans. Plasma Sci. PS-7 120 [4] Y. Nagashima et al 2005 Phys. Rev. Lett. 95095002 *Work supported by the National Natural Science Foundation of China with Contracts Nos.11475222, 11505228, 11735016, 11575238

Speaker: Dr Pengjun Sun (Institute of Plasma Physics, Chinese Academy of Sciences)

IAEA-8-pages-Pengjun_Sun.pdf

Pengjun_Sun-IAEA-Summary_slide.pptx

194 Fast-ion studies in high performance fully non-inductive discharges on EAST

On the EAST tokamak, one hundred seconds steady state H-mode (H98y2~1.1) discharge has been achieved by RF-only (LHW+ECRH+ICRH) heating with improvement of the auxiliary heating and current drive systems on actively cooled ITER-like mono-block tungsten divertor. Towards EAST high performance advanced state-steady operation regimes, fast-ion related physical issues become crucial for achieving EAST scientific objectives with both co-Ip and counter-Ip neutral beam injections [1]. Accordingly, EAST several complementary fast-ion measurements [2] have been developed and validated, e.g. fast-ion D-alpha (FIDA), fast-ion loss detectors (FILDs), neutral particle analyzers (NPA), neutron spectrometers and TOFED, etc. In recent experiments, compared with RF-only discharge, NBI and RF plasmas has a higher βp and H98y2, although the bootstrap current fraction fBS is nearly the same [3], TRANSP analysis shows that it is mostly due to fast ions, and fast ions do not contribute significantly to fBS. To obtain high performance plasma and improve confinement and transport on EAST, key related parameters (e.g. density, plasma current, beam energy, etc.) need to optimize further to reduce the fast ion slowing down time and prompt loss. To investigate fast-ion distribution function and prompt loss, different beam voltage and plasma current are investigated as well. Experimental results show that prompt loss from counter beams is large and can be reduced by reducing beam voltage and increasing plasma current, which is consistent with simulations. The relationship of the fast ion loss and distribution to the different beam settings and plasma parameters will be reported in this paper, which is very helpful to understand energetic particle physics in long pulse H-mode plasmas on EAST and contributes to ITER.

Speaker: Ms Juan Huang (CnIPPCAS)

Summary_2018_JHUANG.ppt

Summary Slide Summary_2018_JHUANG.ppt

195 Global gyrokinetic multi-model simulations of ITG and Alfvenic modes for tokamaks and the first operational phase of Wendelstein 7-X

Results from a hybrid approach (CKA-EUTERPE code) which couples an MHD code with a gyrokinetic code are presented. Although perturbative, it offers a relatively fast way to investigate the destabilisation of Alfven modes by fast particles. TAE saturation amplitudes and their scaling with growth rate and collisionality were investigated in a tokamak as well as in Wendelstein 7-X. Full volume linear electrostatic gyrokinetic simulations for an OP 1.1 Wendelstein 7-X scenario showed modes driven by the strong electron temperature gradient with negligible influence from trapped particles. Using a Fourier solver approach, long-time fully kinetic runs of damped GAEs and TAEs could be performed. Super-resolution methods allowed to accurately resolve the continuous Alfven spectrum.

Speaker: Dr Ralf Kleiber (Max-Planck-Institut für Plasmaphysik)

196 Imaging of SST-1 plasma with LHCD power

Plasma imaging is an essential diagnostics system for any tokamak as it can provide vital information on various plasma parameters. These systems are ones of the first diagnostics installed and are basic not only at start-up stage but also in subsequent operations. Imaging system generally consists of at least two cameras, one of them is a high speed camera and another one is slow speed camera. The first one provides study of fast processes in plasma and plasma-wall interaction. The second camera ensures video image for general plasma operation monitoring. Generally, imaging systems make it possible to plasma monitoring, plasma formation and start-up: break down and ramp-up, study and observation of the magnetohydrodynamic (MHD) instability-edge localized modes (ELMS), multifaceted, asymmetric radiation from the edge (MARFE), displacements study dust migration and deposition study, plasma wall interaction, plasma position control. A Tangential viewing optical imaging system is installed on SST-1. Plasma images are transferred through coherent optical imaging fibre and coupled to the CCD camera placed outside the SST1 machine. The CCD camera used with this system operates at 30 frames/sec to acquire plasma images. The data from the CCD camera is transferred through gigabit Ethernet cable to acquisition PC placed in diagnostics Lab. The whole system is fully automated for operation and data acquisition of the imaging data. In this paper we are presenting observations during LHCD power launching in the SST1 machine. The LHCD pulse was launched into the plasma at various instant of time and varying in pulse length. Plasma images exhibit change in distribution of visible radiation during the interaction of LHCD with the plasma. This increase in emission may be attributed to the enhance in plasma wall interaction as the plasma moves outwards which results in increase of plasma wall interaction. Decrease in plasma size is also observed during interaction of LHCD pulse with plasma.

Speaker: Dr Manoj Kumar (Institute for Plasma Research)

fec18_highlights.pptx

197 Investigations on Temperature Fluctuations and Energy Transport in ETG Dominated Large Laboratory Plasma

Extensive measurements are carried out on micro turbulence because of their possible role in causing anomalous particle and energy transport in fusion devices [1]. Outcome from past investigations suggest that the Electron Temperature Gradient (ETG) driven turbulence is considered presently as a major source of anomalous plasma transport in fusion devices, as transport by ion scale turbulence is largely understood. Direct measurement of ETG is extremely difficult in fusion devices because of its extremely small scale length ($\sim \mu m $ ). In this background, efforts were made in Large Volume Plasma Device (LVPD), to produce plasma suitable for carrying out investigations on ETG turbulence ( $ \sim mm $ ). Introduction of Electron Energy Filter (EEF) divides LVPD plasma into three distinct regions of Source, EEF and Target plasmas. In the core region of target plasma ( $ x \le 45 cm $ ), unambiguous, identification of ETG turbulence is successfully demonstrated [2, 3]. Simultaneous measurement of fluctuations in electron temperature ( $ 10 \% - 30 \% $), plasma density ($ 5 \%-10 \% $) and potential ($ 0.5 \% -2.5 \% $) are carried out. Particle and energy transport are estimated from $ < \tilde{n}_e \tilde{E}_{\theta}> $ and $ < \tilde{T}_e \tilde{E}_{\theta} > $ correlations. It was observed that electrostatic particle transport agrees well with theoretical estimates [4] while, electromagnetic particle flux satisfies the relationship ( $ \Gamma_{es} \sim 10^{-5} \times \Gamma_{es} $ ). Strong negative correlation is observed between fluctuations of density and temperature with potential fluctuations, showing correlation coefficients, $ C_{\tilde{n}_e,\tilde{\phi}} \sim -0.8 $ and $ C_{\tilde{T}_e,\tilde{\phi}} \sim -0.7 $ respectively. This paper will present results on work carried out for energy transport due to ETG turbulence. Details on adopted diagnostic methods, for accurate measurement of temperature fluctuations will also be presented. A comparison will be made of experimentally derived energy transport with theoretically estimated values.

Speaker: Mr Prabhakar Srivastav (Institute For Plasma Research, Bhat Gandhinagar India-382428)

Slide_FEC2018_prabhakar.pdf

198 Leak Width in a Multi-cusp Field Configuration: A Revisit with a Versatile Experimental device

The cusp configuration reduces the plasma losses to boundary by diverging plasma to the narrow regions where the magnetic field lines intersect the wall. The efficiency of multi dipole cusp confinement depends on the plasma losses through cusp loss area, widely known as leak width. The Multi-line cusp Plasma Device (MPD) used electromagnets for plasma confinement and gives opportunity to vary the magnetic field strength which controls the plasma loss area. We discuss the scaling of leak width with different magnetic field strength to understand its role in the particle confinement for such configurations

Speaker: Ms Meenakshee Sharma (Institute for Plasma Research)

Summary_slide_Meenakshee.pdf

199 Model-Predictive Kinetic Control for Steady State Plasma Operation Scenarios on EAST

Robust model-predictive control (MPC) algorithms based on extremely simple linear data-driven models have been recently developed for plasma kinetic control on EAST. This paper shows, for the first time, that MPC can be performed using a two-time-scale approximation, considering the kinetic plasma dynamics as a singular perturbation of a quasi-static magnetic equilibrium, which itself is governed by the flux diffusion equation. This technique takes advantage of the large ratio between the time scales involved in magnetic and kinetic transport, and is applied here to the simultaneous control of the safety factor profile, q(x), and of the poloidal beta parameter, beta_p, on EAST. MPC results in a much faster and more robust control than the so-called near-optimal control algorithms that were tested previously [D. Moreau, et al., Nucl. Fusion 55 (2015) 063011]. The models are state-space models identified with datasets obtained from fast nonlinear METIS simulations (METIS includes an MHD equilibrium and current diffusion solver, and combines 0-D scaling laws and ordinary differential equations). For a given operation scenario, the identified model is augmented with an output disturbance model, which is used to estimate the mismatch between measured and predicted outputs and ensures robustness to model uncertainties. An observer provides, in real time, an estimate of the system states and disturbances, and the controller predicts the behavior of the system over a prediction horizon, taking the actuator constraints into account. For plasma parameters typical of the high-beta_p steady state operation scenarios on EAST, nonlinear closed-loop simulations show that the desired q(x) profiles and beta_p can be obtained in about 2.5 s and 0.5 s, respectively, and with a monotonic approach to their target values. This is essential for avoiding MHD instabilities during the build up of the plasma equilibrium. In these control simulations, the actuators are the LHCD system at 4.6 GHz, the ICRH system, and optionally the plasma surface loop voltage. Various examples are shown, with negative shear or monotonic q-profiles, and with different beta_p target waveforms. The actuators adjust in order to reach the various beta_p targets while maintaining the q-profile in steady state, with the desired shape (or as close as possible if the q(x) and beta_p targets are not achievable).

Speaker: Prof. Didier Moreau (CEA/DSM/IRFM)

SummarySlide_v1.pdf

200 Modeling studies of X-divertor configuration on SST-1 tokamak using SOLPS5.1

To solve the challenging problem of heat removal in a tokamak based fusion reactor, several advanced divertor configurations have been proposed and studied. We present here the reults of our studies of one of the more promising configurations, the X-divertor, conducted for the parameters of the Indian tokamak SST-1. Using the equilibrium code CORSICA, we develop the appropropraite magnetic geometry and then study its performance using the Scrape-Off Layer plasma transport code package SOLPS5.1/B2.5-Eirene. One of the main motivation was to find out if the X-divertor (XD) could boost the heat handling capacity as compared to the standard divertor (SD) configuration for SST-1 that designed to handle 1 MW of total input power. In order to compare the performance XD with the existing SD, we first ensured the core equivalence of both configurations. An additional poloidal field coil was placed behind the divertor target to produce XD configuration. The plasma equilibrium for SD and XD are generated. The divertor index (DI) is varied from 2 to 13. For a plasma operation with P=1 MW input power and plasma edge density ne = 1x1019 m-3 , the peak heat load on the target plates in the X-divertor configuration has reduced by 50% as compared to standard divertor; the heat flux profile near the separatrix was also broadened due to flaring of field lines. The latter increases the plasma-wetted area at the targets. This is a preliminary demonstartion that XD will allow SST-1 to operate at higher input power.

Speaker: Mrs Himabindu Manthena (IPR)

FEC-2018.pdf

201 Nonlinear decay and plasma heating by toroidal Alfvén eigenmodes

Gyrokinetic theory of nonlinear mode coupling as a mechanism for toroidal Alfv\'en eigenmode (TAE) saturation and thermal plasma heating in the fusion plasma related parameter regime is presented, including 1) parametric decay of TAE into lower kinetic TAE (LKTAE) and geodesic acoustic mode (GAM), and 2) enhanced TAE coupling to shear Alfv\'en wave (SAW) continuum via ion induced scattering. Nonlinear decay of TAE into a GAM and a LKTAE with the same toroidal/popoidal mode number is investigated due to its crucial implications on TAE nonlinear saturation, improved confinement, as well as energetic particle (EP) power channeling, including fusion-alpha power density to bulk thermal plasma heating. The parametric dispersion relation is derived and analyzed, and the parameter range for this process to occur and dominate over other mechanisms is discussed. The nonlinearly generated LKTAE and GAM can be dissipated via electron and ion Landau damping, respectively, leading to anomalous EP slowing down and channeling of EP power to thermal ion heating. The thermal plasma heating rates are also estimated. Furthermore, the nonlinearly generated GAM, as the finite frequency zonal flow, could contribute to regulating drift wave turbulence and consequently, improved confinement. The TAE frequency cascading via nonlinear ion induced scattering and saturation due to enhanced coupling to SAW continuum is also investigated. The wave-kinetic equation for the TAE spectrum evolution in the continuum limit is derived using nonlinear gyrokinetic theory, which is then solved to obtain the saturation spectrum of TAE, yielding a lower fluctuation level than previous drift-kinetic theoretical estimates, as a consequence of the enhanced nonlinear couplings in the short wavelength limit. The bulk ion heating rate from nonlinear ion Landau damping is also calculated. Our theory shows that, for TAE saturation in the parameter range of practical interest, several processes with comparable scattering cross sections can be equally important.

Speaker: Dr Zhiyong Qiu (Zhejiang University)

202 Numerical simulations of GAE stabilization in NSTX-U

Simulations of confinement-limiting Alfvén eigenmodes in the sub-cyclotron frequency range show a robust physical stabilizing mechanism via modest off-axis beam injection, in agreement with experimental observations from National Spherical Torus Experiment (NSTX-U). Experimental results from NSTX-U have demonstrated that neutral beam injection from the new beam sources with large tangency radii deposit beam ions with large pitch, which can very effectively stabilize all unstable Global Alfven Eigenmodes (GAEs). Beam-driven GAEs have been linked to enhanced electron transport in NSTX, and the ability to control these modes will have significant implications for NSTX-U, ITER, and other fusion devices where super-Alfvénic fast ions might be present. Nonlinear simulations using the HYM code have been performed to study the excitation and stabilization of GAEs in the NSTX-U right before and shortly after the additional off-axis beam injection. The simulations reproduce experimental finding, namely it is shown that off-axis neutral beam injection reliably and strongly suppresses all unstable GAEs. Before additional beam injection, the simulations show unstable counter-rotating GAEs with toroidal mode numbers and frequencies that match the experimentally observed modes. Additional of-axis beam injection has been modelled by adding beam ions with large pitch, and varying density. The complete stabilization occurs at less than 10% of the total beam ion inventory.

Speaker: Dr Elena Belova (PPPL)

summary_Belova.pdf

summary_Belova.pptx

203 Observations of Plasma Stimulated Electrostatic Sideband Emission and Harmonic Distortion: Evidences of Over-dense Plasma Generation inside a Microwave Discharge Ion Source

Microwave discharge ion source (MDIS) is used in many applications including accelerators based neutron generators on suitable target through D_D or D_T fusion. The electromagnetic (EM) pump wave (ω_0) can propagate beyond cut off plasma density by changing its polarity and/or decomposing into different daughter waves through which it transfer its energy thus producing over dense plasma. Role of electric field on power coupling through different decay channels during density jump from under-dense to over-dense is obtained by theoretical modeling. This is validated with experimentally obtained spectral features in the ion plasma frequency range. In the present experiment, the plasma stimulated emission spectra was measured in the frequency range 0.5ω_0to 3ω_0 to understand the different probable energy decay channels role; e.g. Electron Bernstein waves (EBWs), Ion cyclotron waves (ICWs), Lower hybrid oscillations (LHOs), Ion Bernstein waves (IBWs) and Ion Acoustic Waves (IAWs) etc. The energy decays through different ion-type waves by parametric instability is studied by observing the different side-bands generation around the pump frequency and also the electron cyclotron (EC) harmonic frequencies. The intensity and growth rate of IAWs/ICWs and harmonics (up to 3rd) from parametrically decayed ordinary (O) mode pump wave was used to get an estimate of electric field and localized electron temperature. The density threshold of each electrostatic IAWS/ICWs was measured by stepping pump wave amplitude and external magnetic field. The IAWs lines appear at lower density threshold than the ICWs emission lines. The measured IAWs and ICWs ranges from 317-397 kHz and 410-555 kHz respectively with a density jump from 9.3x1016/m3 to 4.9x1017/m3.At higher density (>3.3x1017/m3), the electrostatic ICWs lines dominates the IAWs thereby yielding negligible damping through ion waves.

Speaker: Mr Chinmoy Mallick (institute for Plasma Research)

Preprint EX-P2-17.pdf

Summary slide-EX-P2-17.pdf

204 Preliminary Results of Wall Conditioning Experiments using High Power ICRH System on SST-1 at Different Toroidal Magnetic Fields

Proper wall conditioning has turned out to be an essential element for achieving the highest possible plasma performance in present-day fusion devices. The main issues are controlling the generation of plasma impurities, liberated by plasma-surface interactions. Superconducting fusion machines need efficient wall conditioning techniques for routine operation in between shots in the presence of high toroidal magnetic field for wall cleaning to control the in-vessel impurities. Ion Cyclotron Wall Conditioning (ICWC) is fully compatible with steady-state tokamak in presence of magnetic field. Here we report the preliminary results of ICRF wall conditioning experiments done on Steady State Superconducting Tokamak (SST-1) using High Power Ion Cyclotron Resonance & Heating (ICRH) System indigenously developed including MW RF generator, Transmission Line with Matching System, Vacuum Transmission Line (VTL) and Fast Wave Poloidal Antenna with Faraday shield. In the first stage, the experiments are conducted to condition the complete system and antenna by introducing low power RF pulses in the SST-1 machine. It is observed that the conditioning pulse removes gas species from Antenna and VTL. In the second stage, the wall conditioning experiments are conducted at 0.2 - 0.4 T and in third stage the wall conditioning experiments are conducted at 1.5 T in Helium gas. The diagnostics used are the visible camera, spectroscopy, Residual Gas Analyzer (RGA) etc. More than 600 RF pulses of 150 kW with 0.5 seconds on time and 0.8 Seconds off time were introduced and significant impurity generation is observed from antenna and vacuum vessel. It is observed that RF conditioning at low pressure releases H2 and other gas species. The previous ICWC experiments done on Aditya tokamak show that in presence of toroidal magnetic field (0.45 T) conditions as well as with 20% Helium gas in a hydrogen plasma is found more effective in releasing wall impurities like water & methane as half an order (~ 5) of initial vacuum condition. The preliminary results on SST1 show that the ICWC in the presence of magnetic field seems to be effective and can be used an alternative method for vessel wall conditioning. In this paper, the above-mentioned experiments and results will be discussed.

Speaker: Mr DHARMENDRA RATHI (INSTITUTE FOR PLASMA RESEARCH)

DRATHI_CN-258_IAEA 2018_Summary_slide.pptx

205 Progress towards Development of Long Pulse ITER Operation through RF Heated H-mode Experiments on EAST and HL-2A

Recent long pulse experiments in EAST have resulted in a new world record of 100 s long H-mode discharge, sustained by the radiofrequency (RF) systems, predominantly Lower Hybrid Current Drive (LHCD). In parallel, experiments in HL-2A have demonstrated successful LH wave coupling in H-mode plasmas with an ITER-relevant passive-active multijunction (PAM) LHCD launcher. These two achievements, obtained as a part of the specific EU-China collaboration, show the viability of LHCD as a successful method for heating and current drive in high performance H-mode plasmas. Experimental comparison of the two LHCD systems in EAST shows that the current drive efficiency is higher for the 4.6 GHz system than for the 2.45 GHz system. Higher power was therefore systematically used on the 4.6 GHz launcher in the long pulse experiments. Increasing the radial distance between the plasma and the launchers (up to 8 cm) was employed as method to optimizing the density in front of the launchers and to avoiding hot spots during the long H-modes. Lithium evaporation showed to have a beneficial effect on the LH current drive efficiency. An increase in efficiency from  = 0.8×1019 AW-1m-2 to 1.1×1019 AW-1m-2 was observed when the accumulated Lithium in the EAST vessel was above 150 g. Good agreement between experimental results and simulations with C3PO/LUKE is obtained for EAST fully non-inductive discharges. C3PO/LUKE can well reproduce the experimental values of the internal inductance, as well as the non-inductive current profile obtained from equilibrium reconstruction constrained by interfero-polarimetry. In HL-2A, a 3.7 GHz LHCD system with four klystrons and an ITER-relevant PAM launcher has been successfully brought into operation and used in H-mode experiments. Coupling of LH waves in ELMy plasmas has thus been demonstrated with an ITER-relevant launcher for the first time. The maximum coupled LH power has reached 1 MW in L-mode and 0.9 MW in H-mode. H-modes were triggered and sustained with LHCD together with ~ 700 kW NBI power. In H-modes with ne > 2.5×1019 m-3, a reduction in ELM amplitude and increase in ELM frequency were observed for injected LH power > 300 kW. The divertor peak heat load released by the ELMs was strongly reduced during this phase, which suggests that the LH power can be used for controlling ELMs.

Speaker: Dr Annika Ekedahl (CEA, IRFM)

Poster_IAEA_2018_Ekedahl_V2.pdf

Summary_slide_IAEA_FEC2018_Ekedahl1.pptx

206 Radial Characteristics of a Magnetized Plasma Column

The cross-field transport of electrons/ions across magnetic field is fundamentally important as it determinines the characteristics of plasma wetted area in the scrape of layer region and particle confinement in magnetically confined plasma devices. The electrically biased objects in the edge region inside tokamaks as well as in Linear plasma devices are known to influence the dynamics of charge particles. The external electrodes in magnetized column can introduce long range electric fields in the plasma column. This leads to either excitation/ suppression of the instabilities resonsible for such transport. In this paper we present experimental results on radial plasma characteristics obtained of a cylindrical plasma column produced in a Linear Device. The magnetized plasma column at one end is terminated with conducting electrodes which are deliberately biased with respct to the plasma. The nature of the long range perturbation during application of electric bias on the electrodes have been investigated using electric probes and its impact on the radial characteristics have been qualitatively explained.

Speaker: Mr Satadal Das (Institute For Plasma Research)

Summary slide.pdf

207 Recent finding in fusion studies using table top and miniaturized dense plasma focus devices operating from hundred joules to less than one joule

In a dense plasma focus (DPF) the plasma is compressed into a hot-warm dense pinch. Since, 50 years ago and during the first three decades the dense plasma focus (DPF) was studied as a possible device to produce dense transient plasmas for fusion research. The trend was to produce bigger devices over MJ stored energy and MA current through the plasma pinch, in order to increase the efficiency of fusion neutron production. Unfortunately, the neutron production suffers saturation in devices operating at MA. Alternatively, in our group we have been studying how scale a dense plasma focus to very low energy of operation, keeping the nuclear fusion reactions and neutron emission. Several dense plasma focus devices under kJ stored energy (400J, 50J, 2J, and 0.1J) were designed and constructed in our laboratory. In all of them nuclear fusion reactions are obtained. In fact, recently we reported the evidence of nuclear fusion in a plasma focus operating in deuterium at only 0.1J. Despite these devices are far to produce net energy, these studies have contributed to learn that it is possible to scale the plasma focus in a wide range of energies and sizes keeping the same value of ion density, magnetic field, plasma sheath velocity, Alfvén speed and temperature. However, the plasma stability depends on the size and energy of the device. Recent findings related nuclear fusion studies are presented, including: a) evidence of nuclear fusion in an ultraminiaturized plasma focus operating at 0.1J; b) observations of plasma filaments and its role in the neutron emission; c) characterization of the plasma ejected after the pinch in table top and small DPF devices (50J, 400J and 900J) and their use to study the effects on materials relevant to the first wall of fusion reactors; and d) studies of the plasma interacting with a target material on front of the anode using digital optical refractive diagnostics and visible spectroscopy. In addition, how to increase the current in the pinch plasma, increasing the number of fusion nuclear reactions and neutron production, in a regime of enhanced stability is discussed. Supported by ACT-172101 CONICYT and FONDECYT 1151471 Chile grants.

Speaker: Prof. Leopoldo Soto (Chilean Nuclear Energy Commission)

208 Reconstruction of MHD modes for energetic particle dynamics studies in toroidal equilibria with arbitrary q profiles

The interaction of energetic particles with MHD modes of different types is a major concern for the next generation of experiments involving burning plasmas. This issue arises in different contexts such as particle redistribution due to current driven instabilities (involving or not magnetic reconnection), activation of Alfven eigenmodes (AE) due to wave-particle interaction or loss of confinement caused by neoclassical tearing modes (NTM). The physics involved in these processes is varied and complex. However, the construction of adequate models to study particle redistribution is usually simplified by assuming that the modes affect the particle dynamics through the perturbation of the equilibrium fields. Thus, the knowledge of the total field, equilibrium plus perturbation, produced in each case enables the calculation of the particle redistribution. In previous works, a model employing a fixed equilibrium and internal modes reconstructed from experimental data was developed and successfully applied to study alpha particle redistribution in the presence of kink modes and sawteeth with partial reconnection. To be able to tackle a larger number of problems, in this work, we extend the method to allow for the use of MHD equilibria with arbitrary safety factor (q) profiles. Again, external data either from experiments or simulations may be incorporated to estimate the structure of the modes. The resulting model is flexible and can be employed to study the effect of MHD modes on test particles in a variety of situations. As a first example, the redistribution of energetic particles caused by the sawtooth crash is considered. Several scenarios are investigated including full and partial reconnection in usual tokamak equilibria as well as configurations with an extended region of low magnetic shear at the plasma core.

Speaker: Dr Pablo Garcia-Martinez (CONICET - Centro Atomico Bariloche)

Garcia-Martinez_et_al_ARG_summary_slide.pdf

209 Self-consistent gyrokinetic description of the interaction between Alfven modes and turbulence

It is getting increasingly clear that many tokamak plasma phenomena which have traditionally been investigated separately, are actually intrinsically linked. One outstanding example along these lines - which is investigated in the present contribution - is the the interaction between Alfven modes (AM), turbulence, and zonal structures (ZS), like zonal flows and geodesic acoustic modes. Recently, a strong interest was raised in the fusion community by the possibility of generating ZS via nonlinear interaction with global modes like Alfven instabilities. In this work, the interaction of AM, turbulence and ZS is studied with the code ORB5. This model treats ions and electrons respectively as gyrokinetic and driftkinetic. ORB5 is a nonlinear global particle-in-cell code, developed for turbulence studies [1] and extended to its electromagnetic multi-species version [2] for the investigation of Alfven dynamics [3]. Recently, the importance of the kinetic electron effects in the ZS dynamics has also been emphasized with ORB5 [4]. ORB5 has also accomplished a verification/benchmark phase for AMs and has been used for the study of the nonlinear wave-particle interaction [5]. The competition between the different excitation mechanisms of ZS is the main focus of this work. When an EP population is added to the electromagnetic turbulence, the perturbed saturated field is observed to be modified by the presence of AMs. The effect of the different players are described separately, and in particular: wave-particle nonlinearity, wave-wave nonlinearity, effect of turbulence on AMs, effect of AMs on turbulence, for example via ZS generation, and bulk plasma omega-star effects on the AM growth rate and saturation. Comparisons with analytical theory and other models like the gyrokinetic Eulerian code GENE [6,7] are also done. [1] Jolliet S., et al. 2007, Comput. Phys. Comm. 177, 409 [2] Bottino A., et al. 2011, Plasma Phys. Controlled Fusion 53, 124027 [3] Biancalani A., et al. 2016, IAEA Fusion Energy Conference, Kyoto, Japan, TH/4-2 [4] Novikau I., et al. 2017, Phys. Plasmas 24, 122117 [5] Cole M. D. J., et al. 2017, Phys. Plasmas 24, 022508 [6] Jenko F. et al. 2000, Phys. Plasmas 7, 1904 [7] Goerler, T. et al. 2011, J. Comput. Phys. 230, 7053

Speaker: Dr Alessandro Biancalani (Max-Planck-Institut für Plasmaphysik)

summary.pdf

210 Simulation of Toroidicity-Induced Alfven Eignenmode Excited by Energetic Ions in HL-2A Tokamak Plasmas

The toroidicity-induced Alfven eigenmode (TAE) excited by energetic ions was first simulated by using GTC code based on HL-2A experimental configuration. The simulation results show that the fraction of energetic (fast) ions in HL-2A experiments is about 3%. The TAE eigenmode frequency is around 211 kHz and is inversely proportional to the square root of electron density, which is quantitatively in agreement with the experimental observation. The real frequency of TAE modes increases with both temperature of energetic ions (beam energy) and toroidal model numbers increasing thanks to the toroidal precession resonance is dominant, but almost keeps constant when the density of energetic ions changes. The growth rates of TAE modes increase with increasing density as well as density gradient of fast ions. The amplitude of the vector potential A// exponentially increases with time for linear TAE mode. Besides, the low n (toroidal mode number) TAE modes, such as n=1 can also be driven by energetic ions when off-axis heating with higher beam energy is employed during HL-2A NBI experiment. The half width of radial mode structures for low n modes is usually wider than those for high n modes. The perpendicular wave vector of the TAE modes and Larmor radius of ions satisfy the relation . At the same time, the polarization of the TAE mode shows that the perturbed parallel electric field is zero. Thus, the TAE mode is close to an ideal MHD mode.

Speaker: Dr Hongda He (Southwestern institute of physics)

211 Simulation Study of Heat Transport with On-Off Axis ICRH in Thailand Tokamak Using BALDUR Code

Self-consistent simulations of plasma in a proposed tokamak design of Thailand Tokamak. (major radius = 65 cm, minor radius = 20 cm, plasma current = 100 kA, toroidal magnetic field = 1.5 T) are carried out using the 1.5D BALDUR integrated predictive modeling code. The simulations are used to investigate plasma transport with on and off axis positions of ion cyclotron resonance heating (ICRH) in the range of 0.3 – 5 MW. The core transport is predicted using the combination of Multimode (MMM95) or Mixed Bohm/gyro-Bohm (Mixed B/gB) anomalous core transport model and NCLASS neoclassical transport model. It is found that the electron temperatures obtained from both simulations are in the range of 0.3 - 1 keV which agree with the HT-6M experimental results. When the ICRH is applied, ion and electron thermal transport increase. Consequently, ion and electron temperature and plasma stored energy increase. During ICRH for both MMM95 and Mixed B/gB model, the electron temperature at the center (Te(0)) ranges from 1 to 1.5 keV with on axis and from 1 to 1.9 keV with off axis. The ion temperature at the center (Ti(0)) ranges from 0.7 to 25 keV with on axis and 50 eV to 7 keV with off axis.

Speaker: Ms Jiraporn Promping (Thailand Institute of Nuclear Technology)

212 Simulations of the Sawtooth-Induced Redistribution of Fast Ions in JET and ITER

Results of simulations of the sawtooth-induced redistribution of fast ions in JET and ITER with the code OFSEF are presented. The dependence of the redistribution on the particle parameters (energy and pitch angle) is studied. The redistribution of the trapped and marginally passing particles is found to exhibit barrier-like behaviour at the separatrix between the trapped and passing particles: the particles with high energies cannot pass the radial coordinate corresponding to the separatrix. The algorithm and structure of the rapid code developed on the basis of the OFSEF calculations are discussed. Simulations of the sawtooth effect on fusion alpha particles in ITER are carried out; they show that when the shape of the q-profile is non-parabolic (which is expected, for example, in the hybrid mode), the post-crash radial profile of the alpha particle distribution function can change significantly. Determining the parameters of a sawtooth crash --- the sawtooth mixing radius and the sawtooth crash duration --- from observations of the electron cyclotron emission in the equatorial plane of a tokamak is discussed; examples for JET sawtooth crashes are presented. Results of simulations of the sawtooth effect on the neutron emission in several recent JET discharges are presented. In most JET discharges, neutrons are mainly born by deuterons of the NBI (neutral beam injection) beam consisting mainly of passing particles with energies ~100 keV. However, in discharges with the third-harmonic ICRH (ion cyclotron resonance heating), a significant fraction of neutrons is produced by the ICRH tail of trapped deuterons in the MeV energy range, which provides an opportunity to verify the theory predictions.

Speaker: Dr Yurii V. Yakovenko (Kyiv Institute for Nuclear Research, Kyiv, Ukraine)

213 Simulations of two types of energetic particle driven geodesic acoustic modes and the energy channeling in the Large Helical Device plasmas

Energetic particle driven geodesic acoustic modes (EGAMs) in the Large Helical Device (LHD) plasmas are investigated using MEGA code. MEGA is a hybrid simulation code for energetic particles (EPs) interacting with a magnetohydrodynamic (MHD) fluid. In the present work, both the conventional and extended models of MEGA are employed. In the conventional model, only the EPs are described by the kinetic equations, while in the extended model not only the EPs but also the thermal ions are described by them. The simulations are conducted based on realistic parameters. The energy of neutral beam injection (NBI) is 170 keV. A Gaussian-type pitch angle distribution is assumed to model the NBI energetic ions. Using MEGA with a conventional model, it is found that the transition between low frequency EGAM and high frequency EGAM is decided by the slope of EP velocity distribution. Also, the phase difference between the bulk pressure perturbation $\rm \delta P_{bulk}$ and EP pressure perturbation $\rm \delta P_{EP}$ are analyzed. For the low frequency EGAMs, $\rm \delta P_{bulk}$ and $\rm \delta P_{EP}$ are in anti-phase. They cancel each other out, which reduces the restoring force of the oscillation leading to the low frequency. While for the high frequency EGAMs, $\rm \delta P_{bulk}$ and $\rm \delta P_{EP}$ are in the same phase. They enhance each other, and thus the frequencies are higher. Using MEGA with an extended model, the low frequency EGAMs are reproduced. The mode structure, mode number, and mode frequency are not only consistent with the results of conventional MEGA model but also consistent with theory and experiment. Also, the energy transfer of various species is analyzed and the bulk ion heating during the EGAM activity is observed. The ions obtain energy when the EPs lose energy, and this indicates that an energy channel is established by EGAM. The EGAM channeling is reproduced by simulation for the first time. From t = 0 to t = 0.36 ms, the energy transferred from EP is 63 J. About half of this energy (51%) is transferred to bulk ions (34%) and electrons (17%), while another half is dissipated. The heating power of bulk ions around t = 0.1 ms is $\rm 3.4~kW/m^3$ which is close to the value $\rm 4~kW/m^3$ evaluated from the experiments.

Speaker: Dr Hao WANG (National Institute for Fusion Science)

H.Wang_Preprint.pdf

H.Wang_Summary.pdf

214 The combined effect of neoclassical tearing modes and ELM control coils on fast-ions: validation in AUG and extrapolation for ITER

This contribution aims to broaden the understanding of the interplay between the internal and external 3D perturbations on the fast ions in tokamak plasmas. At first, we used simulations using the ASCOT suite of codes to analyze an ASDEX Upgrade discharge showing clear sign of the interplay between a (3,2) neoclassical tearing mode (NTM) and external RMP coils on the fast ion loss detector (FILD) signal of neutral beam ion losses. At this context, also a code- code benchmark with the LOCUST code is presented. The same set of analysis tools is then used to predict both the alpha particle and neutral beam ion losses in the ITER 15 MA standard H-mode scenario in the presence of (2,1) and/or (3,2) NTM and ELM control coils (ECC). Magnetically confined fusion relies on that the fusion-born alpha particles will be well con- fined, thus providing significant plasma heating and keeping the first-wall intact. Recent nu- merical simulations indeed show that this is the case for most planned ITER scenarios [1]. However, these simulations were carried out assuming that the transport is fully neoclassical, and that the plasma is MHD-quiescent. Both of these assumptions should be relaxed before making the final verdict on the fast-ion confinement in ITER. In this contribution we partly relax the MHD-quiescence condition by adding NTMs in our simulations. Although a significant up to 100% increase in the total power losses for ITER was observed, so far no direct risk for the first wall was found. In this study both the NTM and the RMP perturbation was assumed to be static, thus maximizing the interaction between the two. Without further increased transport, by for example toroidal Alfven waves or turbulence, the fast ion power loads stay within the engineering limits.

Speaker: Mr Antti Snicker (Aalto University)

summary_slide.pdf

215 Transport induced by energetic geodesic acoustic modes

Energetic particles naturally exist in a tokamak due to either fusion reactions or external heating such as ICRH or NBI. These energetic particles need to be well-confined in order to transfer their energy to thermal particles and achieve this way a regime with self-sustained fusion reactions. However, energetic particles excite modes that tend to de-confine the particles themselves. This is the reason why energetic particle mode excitation and saturation need to be understood and controlled. We focus our analysis on a special class of energetic particle modes, called energetic geodesic acoustic modes (EGAMs). In this work, we present highly resolved full-f global gyro-kinetic 2-species simulations using GYSELA code that evidence the formation of chain of islands in phase space during the nonlinear saturation of EGAMs. Those islands appear at the predicted positions using linear and nonlinear wave-particle interaction theory. By means of a test-particle tracing method we solve the particle equations of motion using the self-consistent electrostatic potential obtained from 2-species GYSELA simulations and show that, even for weak fractions of energetic particles the EGAM island can interact with the trapping/de-trapping region characteristic of toroidal devices. In particular, counter-passing particles can be trapped and eventually de-confined, in agreement with experiments and with previous full-orbit particle simulations. Also, the nature of the transport induced by the energetic modes has been analysed. For this purpose, statistical analysis of 20000 counter-passing particles around the EGAM resonance has been performed. The variance of the particle displacement in phase space shows a super-ballistic transport. When the EGAM saturates the losses increase following also a power law and the transport becomes sub-diffusive.

Speaker: Dr David Zarzoso (CNRS)

Summary_Slide_IAEA.pdf

216 Tungsten control in NBI-dominant H-mode discharges in EAST tokamak

In EAST tokamak, H-mode discharges have been obtained without a basic change at various heating conditions after installation of tungsten monoblocks at upper divertor. Recently, a reproducible long pulse H-mode operation with sufficient tungsten suppression has succeeded for both electron cyclotron resonance and lower-hybrid wave heated discharges and various experimental approaches are also attempted for the tungsten suppression. In discharges dominantly heated by NBI, however, the long pulse H-mode operation has been often restricted by appearance of the tungsten accumulation. Therefore, an exploration of experimental scenarios capable of avoiding the tungsten accumulation is urgently necessary for achievement of the long pulse H-mode discharge with NBI heated high-performance plasma. In the present work, control of the tungsten accumulation in the H-mode discharge with NBI-dominant heating is studied in EAST by measuring tungsten spectra and those radial profiles in extreme ultraviolet (EUV) range at 20-500Å. In order to control the tungsten accumulation in NBI H-mode discharges, experiments have been done by superimposing the LHW heating. One of the experiments is carried out by changing the 4.6GHz LHW power intermittently injected in the NBI H-mode discharge. When the LHW pulse is switched on, plasma particles immediately start to pump out. The tungsten concentration is largely reduced in the plasma core, while the tungsten concentration in the plasma outer region does not change so much. Similar behavior is also observed in the radiation loss. In addition, two-dimensional radiation distribution show that the tungsten accumulates at a very narrow region in plasma core (ρ<0.2) during the NBI phase and considerably flattens during the LHW pulse. These results clearly indicate a change in the tungsten transport in the NBI H-mode discharge. A series of experiments are completed by changing the LHW injection power in the NBI H-mode discharge. As a result, a sufficiently reduced tungsten concentration is obtained at P_{LHW}/P_{NBI} ~1.0, e.g. by an order of magnitude. The beneficial role of LHW injection observed for the first time in EAST is very similar to results of on-axis ECRH and ICRH in ASDEX-U and JET. The tungsten transport in the present experiment is being analyzed with a simulation code.

Speaker: Dr Ling Zhang (CnIPPCAS)

summary slice.pdf

217 Verification and Validation of Integrated Simulation of Energetic Particles in Toroidal Plasmas

Energetic particle (EP) pressure gradients in fusion plasmas can readily excite mesoscale EP instabilities such as the Alfven eigenmodes (AEs) and energetic particle modes that drive large EP transport, which can degrade overall plasma confinement and threaten the machine’s integrity. EP could strongly influence thermal plasma dynamics including the microturbulence and macroscopic magnetohydrodynamic (MHD) modes. In return, microturbulence and MHD modes can affect EP confinement. We have developed first-principles capability for global integrated simulation of nonlinear interactions of multiple kinetic-MHD processes by treating both EP and thermal plasmas on the same footing. Verification and validation have been carried out for the gyrokinetic toroidal code (GTC) simulations of EP interactions with thermal plasmas in a DIII-D NBI-heated plasma. GTC kinetic-MHD simulations of EP interactions with thermal plasmas focus on the DIII-D discharge #159243, which is a NBI-heated plasma with many small-amplitude reversed shear Alfven eigenmodes (RSAE) and toroidal Alfven eigenmodes (TAE), significant flattening of the EP profile, and large amplitude microturbulence. GTC linear simulations using EFIT equilibrium and experimental profiles find that the most unstable AE is RSAE with significant growth rate for toroidal mode number n=3-6. The most unstable RSAE is n=4 and has a radial domain of ⍴=0.3 - 0.6 (square-root of normalized toroidal flux function). These results are in good agreement with other gyrokinetic and gyrokinetic MHD-hybrid codes, as well as experimental data. Consistent with experimental observation, GTC simulations also find that weaker TAE exist at the outer radial domain of ⍴=0.6 - 0.9. The most unstable TAE mode is n=5. Finally, GTC simulations find strong driftwave instability excited by thermal plasma pressure gradients in the core. The most unstable ion temperature gradient (ITG)-like mode is n=20. The linear ITG-like mode amplitude peak at ⍴=0.3, but large fluctuations nonlinearly spread to the whole radial domain. These results indicate that RSAE and TAE in this DIII-D experiment could interact nonlinear with each other and with the microturbulence.

Speaker: Zhihong Lin (UC Irvine)

IAEA_TH-P2-17-ZLin_paper.pdf

218 Kink Mode Study in EAST High β_{P} Plasma

Two types of kink modes, fishbone and long-lived mode are experimentally and numerically studied at EAST tokamak. In high β_{P} plasma, sawtooth instability was replaced by a saturated 1/1 internal kink mode which either manifests itself as a periodical burst energetic ion related fishbone or as a long-lived mode which is associated to the core safety factor at q_0~1. The present of those 1/1 internal modes are beneficial to the sustain of hybrid scenario with extended regions of low-magnetic shear profile and q_0~1, because of that they can expel high-Z impurity and can make flux pumping. The mechanism responsible for the flux pumping caused by kink mode was numerically in nonlinear 3 D magnetohydrodynamic simulations using the M3D code. Furthermore, M3D+K code hybrid simulation shows a good agreement to the fishbone activity in EAST.

Speaker: Dr Liqing Xu

Summary_Slice_IAEA_LXu.pptx

16:10 Coffee Break

OV/5 Overview Magnetic Fusion

219 Overview of HL-2A Recent Experiments

Experiments on the HL-2A tokamak have been aimed at physics issues involved in advanced tokamaks and ITER since the last IAEA FEC. In particular, significant progresses have been made in the following areas: techniques and physics of ELM control, energetic-particle physics, MHD, disruption, multi-scale interactions, physics of advanced tokamak scenario, edge turbulence. Regarding to techniques and physics of ELM control, intensive experiments for controlling ELMs have been performed in HL-2A with several tools, including RMP, LHCD, LBO-seeded impurities (Al, Fe, W) and impurity SMBI (Ar, Ne). The observed ELM mitigation with pedestal turbulence enhancement and radial spectral shift due to the pedestal velocity shear reduction can be qualitatively simulated by a turbulent heat transport model. Toroidal Alfvén eigenmodes (TAE) driven by energetic-ion had been observed on HL-2A. Progress has been made in understanding the physics of instabilities that may interacts with turbulence causing strong influence on cross-field transport and in developing strategies to control them, including neo-classical tearing modes and core-localized Alfven eigenmodes. The stabilization of m/n=1/1 ion fishbone activities by ECRH were found on HL-2A. The experimental results confirmed the stabilization of m/n=1/1 fishbone depends not only on the injected power but also on the radial deposition location of ECRH. Disruption mitigation experiments with a new fast SMBI gas injection system have been recently performed. In HL-2A, advanced tokamak scenario with central q close to 1 was achieved. Auxiliary heating (mainly NBI) during the current rise phase was used, creating ITBs with a weak magnetic shear in the plasma centre. In ITB plasmas with weak magnetic shear, kinetic electromagnetic instabilities were confirmed and investigated. For the study of edge turbulence and flows, a signature of incoherent phase slips was evidenced by the study on the interaction between E×B shear and cross phase between radial velocity perturbation and poloidal ¬velocity perturbation. In the pedestal region, the dynamics of the plasma flows, turbulence and pedestal formation across the L-I-H transition were studied by Doppler reflectometry. The electromagnetic character of filamentary structure was measured in the scrape off layer of HL-2A for the first time.

Speaker: Dr Min Xu (CnSWIP)

IAEA_FEC_OV5-1_HL2A_M_Xu_one_slide.pptx

IAEA_FEC_Overview_HL2A_M_Xu_V18.pptx

220 Physics research on the TCV tokamak facility: from conventional to alternative scenarios and beyond

The research program of the TCV tokamak ranges from conventional to advanced tokamak scenarios and advanced divertor configurations, to exotic plasmas driven by theoretical insight, exploiting the device’s unique shaping capabilities. The facility is operated intensively both domestically and with EUROfusion support. The new 1-MW NBI has expanded the parameter range, now encompassing ELMy H-modes in an ITER-like shape, stationary non-inductive discharges sustained by ECCD and NBCD, and negative-triangularity diverted plasmas. Disruption avoidance by real-time locked mode prevention or unlocking with ECRH was thoroughly documented, using magnetic and radiation triggers. Runaway generation with high-Z noble gas injection and runaway dissipation by subsequent Ne or Ar injection were studied for model validation. Turbulence is reduced in the core at negative triangularity, consistent with increased confinement and in accord with global gyrokinetic simulations. The GAM, possibly coupled with avalanche events, has been linked with particle flow to the wall in diverted plasmas. In H-mode, the pedestal pressure and plasma stored energy are insensitive to fueling, whereas nitrogen seeding moves the pedestal outwards and increases the stored energy. High fueling at high triangularity (0.54) is key to accessing the attractive small-ELM (type-II) regime. Detachment, SOL transport, and turbulence were studied in L- and H-mode in both standard and alternative configurations (snowflake, super-X, and beyond). The L-H transition threshold is independent of the divertor topology. In the attached L-mode phase, an increase in flux expansion or divertor leg length reduces the power exhausted at the outer strike point and increases radiation. The detachment process is caused by power “starvation” reducing the ionization source, with volume recombination playing only a minor role. The SOL density shoulder observed at high collisionality is correlated with increased blob size. A doublet plasma, featuring an internal X-point, was achieved successfully, if only transiently, and a transport barrier was observed in the mantle just outside the internal separatrix. In the near future variable-configuration baffles and cryopumping will be introduced to investigate the effect of divertor closure on exhaust and performance, and 2-MW ECRH and 1-MW NBI heating will be added.

Speaker: Dr Stefano Coda (CRPP-EPFL)

sc_iaea_18.pptx

sc_iaea_18_wide.pptx

sc_iaea_18_with_backups.pptx

221 Overview of Operation and Experiments in the ADITYA-U Tokamak

Ohmically heated circular limiter tokamak, ADITYA has been upgraded to a tokamak named ADITYA Upgrade (ADITYA-U) having open divertor configuration with divertor plates. Experiment research in ADITYA-U (R0 = 75 cm, a = 25 cm) has made significant progress, since last FEC 2016. After successful commissioning of ADITYA-U, the Phase-I plasma operations have been conducted from December 2016, with graphite toroidal belt limiter. Filament pre-ionization assisted purely Ohmic discharges with circular plasma have been obtained. Hydrogen gas breakdown has been obtained in each of ~ 700 discharges without a single failure. Repeatable plasma discharges of plasma current ~ 80 kA – 95 kA, duration ~ 80 – 100 ms with toroidal magnetic field (max.) ~ 1T and chord-averaged electron density ~ 2.5 x 10^19 m^-3 has been achieved. Later, the discharge duration has been enhanced up to ~ 180 ms with the application of negative converter along with better wall conditioning, achieved by implementing the Glow Discharge Cleaning (GDC) with Ar: H2, He: H2 gas mixture and with intense short plasma pulses in ECR produced plasma background. Being a medium sized tokamak, runaway electron generation, transport and mitigation experiments have always been one of the prime focus of ADITYA-U. MHD activities and density enhancement with H2 gas puffing has also studied. The Phase-I operation was successfully completed in March 2017. The Phase-II operation preparation in ADITYA-U includes, calibration of magnetic diagnostics followed by commissioning of major diagnostics and installation of baking systems. After repeated cycles of baking the vacuum vessel up to ~ 130°C, the ADITYA-U Phase-II operations have been resumed from February 2018 and is continuing in order to achieve plasma parameters close to the design parameters of circular limiter plasmas using real time plasma position control. Several experiments, including the fueling with Supersonic Molecular Beam Injection, H2 gas puffing for runaway control during current flat-top and disruptions, Neon gas puff assisted radiative improved confinement and the experiments related to plasma shaping is undergoing. The complete upgradation including dismantling of ADITYA and reassembling of ADITYA-U along with experimental results of Phase-I and Phase-II operations from ADITYA-U and overall progress will be discussed in this paper.

Speaker: Mr Rakesh Tanna (Institute For Plasma Research)

RLTanna_OV5-3_talk_IAEA_FEC_2018_Final.pdf

Summary_slide_RLTanna_OV-5-3_FEC_2018.pdf

222 Tokamak research in Ioffe Institute

Research of various aspects of tokamak physics is conducted on small tokamaks at Ioffe Insitute in a wide range of experimental conditions: R/a=1.6, Bt=0.5(1.0) T, Ip=250(500) kA – Globus-M(M2), R/a=2.4, Bt=1.0 T, Ip=150 kA – TUMAN-3M, R/a=7.0, Bt=3.0 T, Ip=25 kA – FT-2 tokamaks. Results obtained in final Globus-M experimental campaign (before upgrade shutdown) with the 25% toroidal magnetic field and plasma current increase up to 0.5 T and 250 kA respectively are presented. In these experiments an overall improvement in plasma performance was observed. Energy confinement time study was performed in both OH and NBI heated H-mode plasma. Strong tau_E dependence on both Ip and Bt was observed, while the dependence on density and absorbed power was similar to the conventional H-mode scaling IPB98(y,2). The lifetime of modes with ITB reached a few confinement times before the q=1 resonant surface appeared in the plasma. Plasma confinement was also studied in the compact TUMAN-3M tokamak. No noticeable isotope effect in particle confinement in hydrogen and deuterium ohmic L-mode was observed. On the contrary, in the ohmic H-mode particle confinement was approximately 1.5 times higher in deuterium than in hydrogen. Study of TAEs on Globus-M was performed at increased magnetic field. The mode character and influence on the fast ions changed with the increase of the Bt and Ip. At TUMAN-3M Ion Cyclotron Emission in OH and NBI heated discharges was studied. Application of the NBI revealed central location of ICE, excitation by sub-Alfvénic beam ions and fine structure of the emission spectral lines. New diagnostics, designed for Globus-M2, were installed and tested on Globus-M. At the FT-2 tokamak the ELMFIRE global gyrokinetic modeling of the OH discharge is compared to the experimental data using the specially developed fast linear version of the X-mode DR synthetic diagnostics. The anomalous absorption of the pump wave in the ECRH experiments due to the parametric excitation of trapped UH waves in the vicinity of the density or magnetic field profile local maximum is considered.

Speaker: Dr Nikolai Bakharev (Ioffe Institute)

Bakharev presentation.pdf

summary_slide_Bakharev.pdf

223 Overview of recent progress in understanding NSTX and NSTX-U plasmas & Overview of new MAST physics in anticipation of first results from MAST Upgrade

A. The mission of the spherical tokamak NSTX-U is to explore the physics that drives core and pedestal transport and stability at high-β and low collisionality, as part of the development of the ST concept towards a compact, low-cost ST-based Pilot Plant. NSTX-U will operate at up to 2 MA and 1 T with up to 10 MW of Neutral Beam Injection (NBI) power for 5 seconds with up to 4 MW of High Harmonic Fast Wave (HHFW) power. In this parameter space, electromagnetic instabilities are expected to dominate transport. Furthermore, beam-heated NSTX-U plasmas will be able to explore the energetic particle (EP) phase space that is relevant for both α-heated conventional and low aspect ratio burning plasmas. A further objective is to develop the physics understanding and control tools to ramp-up and sustain high performance plasmas in a fully-noninductive fashion for pulse lengths up to 5 s. NSTX-U began research operations in 2016, producing 10 weeks of commissioning and scientific results. However, a number of technical issues, including the failure of a key divertor magnetic field coil, resulted in the suspension of operations and initiation of Recovery activities. During the Recovery outage, there has been considerable work in the area of analysis, theory and modeling with a goal of understanding the underlying physics to develop predictive models that can be used for high-confidence projections for both ST and higher aspect ratio regimes. The studies have addressed issues in thermal plasma transport, indicating the importance of non-local and multi-scale effects, EP-driven instabilities at ion-cyclotron frequencies and below, studying the wave-particle interactions and development of descriptive predictive models, and heat flux width modeling and the role of turbulence broadening. NSTX-U is expected to resume operations during CY2020.

This work was supported by US Department of Energy Contract No. DE-AC02-09CH11466

B. MAST Upgrade will operate in 2018 with unique capabilities to explore plasma exhaust and alternative divertor configurations to address this key issue for DEMO. Modelling of the interaction between filaments with BOUT++ indicates filaments separated by more than 5x their width move independently, and their velocity is slightly perturbed by if their separation is 1 width, suggesting radial density profiles can be modelled as the superposition of filaments. Secondary filaments on MAST are found up to 1ms after type-I ELMs that correlate with plasma interaction with surfaces near the X-point. A quiescent region devoid of filaments near the X-point has been routinely observed, extending from the separatrix to a normalised flux of 1.02. Counter-streaming flows of doubly ionised carbon along field lines, generated by localised gas puffing, have been observed and reproduced in EMC3-EIRENE simulations. MAST-U will be an excellent facility for understanding detachment onset and control in closed divertors. SOLPS modelling predicts the upstream density needed to reach detachment will be over 2x lower in the Super-X configuration compared with the conventional divertor due to increased total magnetic flux expansion. Analytic modelling predicts detachment control in a Super-X is more amenable to external control. Detailed measurements of transport through the edge have been made in MAST L-mode plasmas to characterise a Geodesic Acoustic Mode 2cm from the separatrix. Interpretation of plasma potential profile measurements using ball-pen probes have been improved through kinetic modelling, showing that electrons polarise the material around the probe, leading to ExB drifts of ions to the probe.
Measurements of the effects of sawteeth on fast ion confinement on MAST indicate that passing and trapped particles are equally redistributed by the sawtooth crash. There is no apparent energy threshold for redistribution, indicating redistribution due to a mechanism resonant with the m=1 perturbation. Gyrokinetic simulations of ETG turbulence in MAST are in close agreement with the measured collisionality dependence of the energy confinement time. Beam emission spectroscopy measurements show that flow shear leads to eddy tilting in up-down symmetric plasmas and skewed density fluctuations. First results from MAST Upgrade operations will be presented.

Speaker: Dr Jonathan Menard

OV-5-5R_SummarySlide.pdf

OV_R5-5.pdf

OV_R5-5.pptx

224 Overview of new MAST physics in anticipation of first results from MAST Upgrade

MAST Upgrade will operate in 2018 with unique capabilities to explore plasma exhaust and alternative divertor configurations to address this key issue for DEMO.
Modelling of the interaction between filaments with BOUT++ indicates filaments separated by more than 5x their width move independently, and their velocity is slightly perturbed by if their separation is 1 width, suggesting radial density profiles can be modelled as the superposition of filaments. Secondary filaments on MAST are found up to 1ms after type-I ELMs that correlate with plasma interaction with surfaces near the X-point. A quiescent region devoid of filaments near the X-point has been routinely observed, extending from the separatrix to a normalised flux of 1.02. Counter-streaming flows of doubly ionised carbon along field lines, generated by localised gas puffing, have been observed and reproduced in EMC3-EIRENE simulations. MAST-U will be an excellent facility for understanding detachment onset and control in closed divertors. SOLPS modelling predicts the upstream density needed to reach detachment will be over 2x lower in the Super-X configuration compared with the conventional divertor due to increased total magnetic flux expansion. Analytic modelling predicts detachment control in a Super-X is more amenable to external control.
Detailed measurements of transport through the edge have been made in MAST L-mode plasmas to characterise a Geodesic Acoustic Mode 2cm from the separatrix. Interpretation of plasma potential profile measurements using ball-pen probes have been improved through kinetic modelling, showing that electrons polarise the material around the probe, leading to ExB drifts of ions to the probe.
Measurements of the effects of sawteeth on fast ion confinement on MAST indicate that passing and trapped particles are equally redistributed by the sawtooth crash. There is no apparent energy threshold for redistribution, indicating redistribution due to a mechanism resonant with the m=1 perturbation.
Gyrokinetic simulations of ETG turbulence in MAST are in close agreement with the measured collisionality dependence of the energy confinement time. Beam emission spectroscopy measurements show that flow shear leads to eddy tilting in up-down symmetric plasmas and skewed density fluctuations. First results from MAST Upgrade operations will be presented.

Speaker: Dr Jonathan Menard

MAST_overview_summary_slide.pptx

Nuclear Fusion Board Meeting

Wednesday, 24 October

IFE/1 Inertial Fusion Experiments & Theory

225 Two-colors mixed petawatt laser designed for fast ignition experiment

Here we report a novel design of a heating laser for the fast ignition, combining fundamental and second harmonics lights. Such a two-colors laser is expected to heat a dense core more efficiently than a laser only with a fundamental light. We chose a LBO (LiB3O5) crystal which can convert a focusing beam due to its large acceptance of phase matching angle. We experimentally demonstrated the second harmonic conversion with efficiency of 60% at the maximum. The LBO crystal shows a high damage threshold more than 5 J/cm2 with a down-scale LFEX beams. A full size (10 cm×10 cm×2 mm) LBO crystal was manufactured completely and is ready to install for the full-scale LFEX operation.

Speaker: Dr Yasunobu Arikawa (Insituteof Laser Engineering Osaka University)

IAEA2018Arikawa(India).pptx

IAEA2018Arikawa-summary slide.pptx

226 Production of keV-Temperature Plasma Core with Magnetized Fast Isochoric Heating

The quest for the inertial confinement fusion (ICF) ignition is a grand challenge, as exemplified by extraordinary large laser facilities like National Ignition Facility (NIF) [J. Lindl et al., Phys. Plasmas 11, 339 (2004), J. Lindl et al., Phys. Plasmas 21, 020501 (2014)]. Although scientific break-even, the energy released by fusion reaction exceeds the energy contains in the compressed fusion fuel, was achieved on NIF [O. A. Hurricane et al., Nature 506, 343 (2014)], the pathway to the ignition is still unclear. Fast isochoric heating, also known as fast ignition, of a pre-compressed fuel core with a high-intensity laser is an attractive and alternative approach to the ICF ignition [M. Tabak et al., Phys. Plasmas 1, 1637 (1994)] that avoids the ignition quench caused by the hot spark mixing with the cold fuel, which is the crucial problem of the currently pursued ignition scheme. High-intensity laser-plasma interactions efficiently produce relativistic electron beams (REB). However, only a small portion of the REB collides with the core because of its large divergence. Here we have demonstrated enhanced laser-to-core coupling with a magnetized method to confine the REB in a narrow transport region resulting in efficient isochoric heating. The method employs a laser-produced kilo-tesla-level magnetic field [S. Fujioka et al., Sci. Rep., 3, 1170 (2013)] that is applied to the transport region from the REB generation point to the core which results in guiding the REB along the magnetic field lines. We have created successfully a 1.6 ± 0.2 keV-temperature plasma core having 1 Gbar of energy density by using the MFI scheme with 7.7 ± 1.3% of an efficient laser-to-core energy coupling [S. Sakata et al., ArXiv 172.06029 (2017)]. We should emphasize that our result can be explained by a simple model coupled with the comprehensive plasma diagnostics, while several ICF experiments relay heavily on computer simulations due to difficulties of diagnosing micro-scale phenomena occurred in the small and complex plasma. The simplicity may secure scalability of this scheme to the ignition. 15% of the laser-to-core coupling is achievable for an ignition-scale high area density core (0.3 - 0.5 g/cm2) according to the model. The ignition target based on the MFI scheme is being designed by using multi-scale and multi-dimensional simulations.

Speaker: Prof. Shinsuke Fujioka (Institute of Laser Engineering, Osaka University)

181001IAEA-FEC_one_slide.pdf

181015IAEA-FEC2018.pptx

227 Liquid DT Layer Approach to Inertial Confinement Fusion

The baseline approach to high gain ICF involves the implosion of capsules containing a layer of DT ice [1]. DT ice layer designs require a high convergence ratio (CR > 30) implosion, with a hot spot that is dynamically created from DT mass originally residing in a thin layer at the inner DT ice surface. Although high CR is desirable in an idealized 1D sense, it amplifies the deleterious effects of realistic features and asymmetries [2]. An alternative ICF concept uses DT liquid layers [3]. DT liquid layers allow for much higher vapor densities than are possible with DT ice layers. The wide range of vapor densities that are possible with DT liquid layers provides flexibility in hot-spot CR (12 < CR < 25), which, in turn, will provide a reduced sensitivity to asymmetries and instability growth. Given enough vapor mass, the hot spot can be formed from the mass originally residing in the central vapor region. Recent experiments at the National Ignition Facility (NIF) have demonstrated cryogenic liquid DT layer ICF implosions, along with the associated flexibility in the hot spot CR [4,5].
There are tradeoffs involved in high CR ice layer and reduced CR liquid layer designs. With reduced CR, hot spot formation is expected to have improved robustness to instabilities and asymmetries [2-5]. In addition, the hot spot pressure (Pr) required for self-heating is reduced if the hot spot radius (Rhs) is increased (Pr α Rhs^-1). With a reduction in the hot spot Pr requirement, the implosion velocity and fuel adiabat requirements are relaxed. On the other hand, with larger hot spot size, the hot spot energy requirement for self-heating (Ehs) is increased (Ehs α Rhs^2), and the required capsule absorbed energy is increased. In this presentation, we will summarize the recent liquid layer experiments at the NIF and will discuss the hot spot energy, hot spot pressure, cold fuel adiabat, and capsule-absorbed energy requirements for achieving self-heating and propagating burn using liquid layer capsules with hot spot CR<20.

References
[1] S. W. Haan et al., Phys. Plasmas 18, 051001 (2011).
[2] B. M. Haines et al., Phys. Plasmas 24, 072709 (2017).
[3] R. E. Olson and R. J. Leeper, Phys. Plasmas 20, 092705 (2013).
[4] R. E. Olson et al., Phys. Rev. Lett. 117, 245001 (2016).
[5] A. B. Zylstra el al., Phys. Plasmas, to be published (2018).

Speaker: Dr Ray Leeper (Los Alamos National Lab)

Liquid DT Layer Approach To Inertial Confinement Fusion Final.pdf

Liquid DT Layer Approach To Inertial Confinement Fusion Final.pptx

228 Thermo-mechanical and Atomistic Assessment of First Wall and Optics in non-protective chamber in Inertial Fusion Energy

Different Inertial Fusion Energy (IFE) First Wall (FW) protections have been proposed in diverse conceptual designs that lead to very different irradiation conditions and macroscopic effects. A review is needed to understand their behavior. Some years ago a European proposal projected the possibility of non-protective FWs considering W and nano-tungsten. This work is describing in detail the behavior of a W and nano-tungsten first wall under pulsed irradiation conditions predicted for the different operational scenarios of that laser fusion project by using advanced engineering modeling tools. Starting with the calculations of the time-dependent pulsed radiation fluxes, assuming 3D geometrical configurations, we estimate the irradiation-induced evolution of first wall temperature as well as, the thermo-mechanical response of the material. Finally, we carry out crack propagation calculations. Results allow us to define operational windows and to identify the main limitations for operation. The atomistic effects of irradiation in the FW are the other key magnitude to determine available lifetime. The role of grain boundaries on the radiation-induced damage and light species behavior is studied both experimentally and computationally, also under pulsed conditions. Important differences are observed in the density of vacancies between nanostructured and coarse-grained samples as well as the preferential places for H accumulation concluding with the influence of temperature.
Optics damage is a great concern in IFE; a new full conceptual final focusing system based on silica transmission lenses for dry wall chambers was designed assuming pulsed conditions based on a temperature control system by using a heat transfer fluid. Optical response of composite materials containing metal nanoparticles was investigated and optimized. Highly concentrated silver colloidal nanoparticle solutions were produced thanks to fs laser ablation and it was demonstrated that such embedded plasmonic nanoparticles may be viable candidates to reduce damages produced on optics by swift heavy ions due to the change of their shape under irradiation.

Speaker: Prof. Jose Manuel Perlado (Instituto Fusion Nuclear / Universidad Politécnica Madrid)

Presentation2 IAEA FEC Ahmedabad Perlado_IFE1-4.pdf

229 Demonstrations of foam shell and infrared heating methods for FIREX targets

We study fuel layering for Fast Ignition Realization Experiment (FIREX) cryogenic targets according to two strategies: a foam shell and Infrared (IR) heating. Foam is a porous material and would soak up a liquid fuel uniformly by capillarity. The method has the difficulty to form void-less solid fuel because of the density difference between the liquid and solid phases. We have demonstrated the residual void fraction of ~1 % in a foam wedge. ANSYS simulations have represented that the technique would be applicable to a FIREX target. We examine the simulated process using a dummy foam shell target and succeed to form an ice layer with a reduced void fraction. The IR heating technique has originally been developed for central ignition targets, which requires spherical symmetry. We modify it for an axisymmetric FIREX target. We have developed the dedicated layering system with additional temperature control of the cone. To date, the sphericity of a formed ice layer reaches 95 %.

Speaker: Dr Akifumi Iwamoto (National Institute for Fusion Science)

IFE1-5_IWAMOTO_16-9.pptx

IFE1-5_IWAMOTO_Summary_16-9.pptx

IFE1-5_IWAMOTO_Summary.pdf

P3 Posters

230 2D and 3D modelling of JT-60SA for disruptions and plasma start-up

The JT-60SA is a superconducting tokamak device being built as a joint international project between Japan and Europe in the frame of the broader Approach agreement. One of the main goals of JT-60SA is to study practical and reliable plasma control schemes in view of the power plant. Plasma electromagnetic modelling is one of the essential tools for plasma operation in a fusion device and they require detailed models for ensuring an accurate preparation of the magnetic controllers. To achieve this goal, suitable models are needed at different level of details. 2D plasma nonlinear equilibrium codes are used to develop the operational scenarios and to perform breakdown studies. Furthermore, three-dimensional modelling permits the assessment of 3D vessel structures on the plasma behaviour, e.g. during disruptions, as well as to study non-axisymmetric plasma instabilities. On the other hand, engineering-oriented models are essential for the commissioning of the magnetic diagnostics, and the design of control algorithms. In this context, a set of alternative modelling tools based on the CREATE 2D equilibrium codes have been developed as additional benchmark for magnetic modelling. These tools have been exploited to perform breakdown studies and to design a preliminary functional architecture of the plasma magnetic control system. Furthermore, several studies of the impact of three-dimensional structures on plasma evolution have been carried out, ranging from pure electromagnetic analysis of the magnetic field produced by the non-axisymmetric coils, to nonlinear evolution of n=0 instabilities. In this paper, we report on the activities that have been carried out exploiting the CREATE modeling tools. In particular, 2D modelling has been exploited to study the magnetic configurations for the EC assisted breakdown, while 3D tools have been used to evaluate the effect of three-dimensional structures on evolutionary equilibrium of axisymmetric plasmas.

Speaker: Prof. Gianmaria De Tommasi (Università degli Studi di Napoli Federico II)

231 3MW Dual Output High Voltage Power Supply Operation: Results for Accuracy, Stability and Protection Test

High temperatures inside tokamak for fusion research is achieved from auxiliary heating systems like neutral beam injectors (NBI), or RF heating devices, viz., ion cyclotron (IC), electron cyclotron and lower hybrid systems where High Voltage Power Supply (HVPS) is an essential requirement. ITER requires 20 MW of ICRF for heating and driving plasma current. A cascaded chain of amplifier is a practical solution due to limiting level of power with available vacuum tubes. Each chain of amplifier has to provide 1.5MW power in frequency range of 35- 65 MHz for 3600 seconds. The system must be capable to operate both at matched and mismatched load condition (VSWR 2) [1]. HVPS based on pulse step modulation (PSM) topology has already demonstrated its ability for broadcast transmitters, accelerators using radio frequency (RF) source and neutral beam injectors. A novel concept of tapping two outputs from single PSM based HVPS is attempted for the first time. A PSM based HVPS is developed with dual output to feed driver and end stages of a high power RF amplifier [2]. Developed dual output HVPS is capable of providing 14 - 18 kV, 250 kW to driver stage and 16-27 kV, 2800 kW to end stage of a RF amplifier chain, simultaneously [3]. Present article covers the validation of dual output HVPS for integrated operation with RF Amplifier system. It includes wire burn test conducted at the output of HVPS, demonstrating tight synchronization among both stages. Test set up, gauge/length for fuse wire to meet the critical energy limit qualifications is presented. HVPS performance parameters viz. ripple, regulation and stability over extended duration of 3600 seconds are presented for various scenario of RF Amplifier operation. Implemented scheme for protection against overvoltage and overcurrent is also discussed. [1]Aparajita Mukherjee et al., “Progress in High Power Test of R&D Source for ITER ICRF system”, unpublished, FEC 2016. [2]A.Patel et al., “Development of 3 MW Dual Output High Voltage Power Supply for ICRH System”, International Power Modulator and High Voltage conference (IPMHVC-2016), San-Francisco, July 5-9, 2016 [3]A.Patel et al., “Initial operation of 3 MW dual output high voltage power supply with IC RF system”, Fusion Engineering and Design, Volume 126, January 2018, Pages 59–66.

Speaker: Mr AMITKUMAR PATEL (INSTITUTE FOR PLASMA RESEARCH)

SUMMARY.pdf

232 A Concept of Self-Cooled Breeding Blanket with Advanced Molten Salt Flinak for High-Efficiency and Long-Life Operation

An advanced molten salt (AMS), in which powders of hydrogen-soluble and chemically reactive metals such as titanium are mixed, is investigated as a potential self-cooled breeding blanket material. It is shown that hydrogen isotope uptake in a vanadium plate in molten salt FLiNaK is suppressed by the addition of Ti powders into the salt. In addition, the corrosion of candidate structural materials in FLiNaK with HF is also suppressed by the addition of titanium powders. Considering these result, tritium formed in the molten salt in fusion blanket will be trapped by the Ti powders, not being trapped by the structure materials (vanadium alloy) and not corroding the structure materials. Neutronics and tritium mass balance calculations are also performed and it is showed that FLiNaK based Be-free blanket is feasible.

Speaker: Mr Juro Yagi (Institute of Advanced Energy, Kyoto University)

1p slide.pdf

233 A Multi-Parameter Optimization technique considering temporal and spatial variation in nuclear response of materials in Fusion devices

Structural materials present in and round any fusion device will face stringent conditions due to the high-energy, high-intensity neutron emitted from the fusion plasma. This will have significant life-limiting impacts on the reactor components of both experimental and commercial fusion devices. The neutrons interact with the material initiating nuclear reaction leading to the production of radioactive isotopes, gas molecules and related defects. These gases, particularly helium, can cause swelling and embrittlement of the material. Furthermore, the radioactive isotopes produce would cause heating in the material. These isotopes may have long lives which would contribute towards the radwaste produced in the fusion devices. Hence designing of low activation materials for fusion devices is warranted. At Iter-India, Institute for Plasma Research a number of computational tools are being developed to estimate the nuclear response of the materials and to optimize accordingly. ACTYS-1-GO, a multipoint neutron activation code which can calculate radiological responses of materials located at various positions in a fusion reactor efficiently is developed. Also, a mathematical framework is developed for accessing the relationship of radiological quantity with the initial elements present in the material. Such framework helps in identifying and minimizing the fraction of most dangerous elements/isotopes from the material composition. In the present study both the methodologies are efficiently coupled for a complete material optimization. Quantities responsible for various radiological effects (like activity, dose, heat, and radwaste) and related defects in the material are considered and their contributing elements are optimized accordingly. Also, since a single material faces a gradient of neutron flux over its entire volume, all such optimization is carried out over the entire range of neutron flux faced by that material. This provides a comprehensive picture of the response of the material to neutron irradiation, enabling the assessment of structural integrity of components in a fusion device.

Speaker: Ms Priti Kanth (Institute for Plasma Research, HBNI)

Composition optimization strategy based on multiple radiological responses for materials in spatially and temporally varying neutron fields

summary slide_Priti Kanth.pdf

234 Advanced capabilities of multi-functional calculation program SuperMC3.2 for complex nuclear system

Super Multi-functional Calculation Program for Nuclear Design and Safety Evaluation, SuperMC, is a full-function neutronics simulation software system including inner-coupled calculations among efficient radiation transport, depletion, activation and shutdown dose. Its advanced capabilities include CAD/image-based accurate modeling for complex irregular geometry, intelligent data analysis based on multi-D/multi-style visualization and network collaborative nuclear analysis on cloud computing platform. Besides, several advanced radiation transport methods such as global weight window generator (GWWG) were proposed to solve the key problems for radiation protection in fusion system, such as deep penetration problem, sky scattering problem. SuperMC has been verified and validated by more than 2000 benchmark models and experiments including HCPB mock-up experiments in SINBAD, IAEA-Activation Calculation Benchmark (ACB), FNG-ITER SDR experiment and so on. And it was also applied in the neutronicis analysis of ITER, DEMO, etc.

Speaker: Dr Lijuan Hao (Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui, 230031, China)

FEC-1ppt.pdf

235 Application of ANSYS FLUENT MHD Code for Liquid Metal MHD Studies

Magneto Hydro Dynamic (MHD) phenomena plays an important role in governing liquid metal flow characteristics under strong transverse magnetic field and has, therefore, gained the attention of fusion community for the design of liquid breeder blankets. In presence of plasma confining toroidal magnetic field, the flow of electrically conducting liquid metal (Li/Pb-Li), typically used for coolant and/or tritium carrier, is greatly affected due to flow opposing Lorentz force, which arises due to interaction between magnetic field and induced current in the liquid metal. For the successful design and development of liquid breeder blankets, detailed MHD analysis is highly desirable to understand various effects of MHD, such as change in velocity profile, pressure drop, heat transfer etc. The liquid metal MHD studies are being carried out using both analytical and numerical approaches. The analytical solutions, derived under 2D fully developed flow approximations, are limited to the simple flow geometries and hence they are not applicable for the analysis of complex blanket flow configuration, which consists of bends, transition zone, multichannel flow etc. Numerical simulation techniques are, therefore, used extensively to perform MHD analysis in such complex flow configuration and various MHD codes, either newly developed or commercially available are being reported. The MHD code, however, needs to be benchmarked extensively and validated before its application to complex flow configuration in liquid breeder blanket. In the present work, three MHD benchmark problems of ref. [1] has been successfully analyzed using ANSYS FLUENT MHD code and results are compared with available literature data. The selected problems are (i) 2D fully developed laminar steady MHD flow, (ii) 3D laminar, steady developing MHD flow in a non-uniform magnetic field and (iii) MHD flow with heat transfer (buoyant convection). The results have provided more confidence in using FLUENT as a promising MHD analysis tool for fusion application. The numerical model, analysis, methodology and simulation results of each benchmark problem will be discussed in detail. References: 1. S. Smolentsev, S. Badia , R. Bhattacharyay etal, FED 100 (2015) 65–72.

Speaker: Mrs Anita Patel (Institute For Plasma Research)

Summary Slide_Anita_FIP P3-30_FEC_Preceedings_submitted.pdf

236 Artificial Neural Network for Yield Strength Prediction of Irradiated RAFM Steels

Structural materials to be used in proposed fusion reactor will be exposed to hostile neutronic environmental conditions. These steels will interact with high energy neutron particles. The interaction is expected to degrade structural material properties such as loss of ductility, increase of yield strength and DBTT temperature. Artificial neural network (ANN) with back-propagation (BPN) technique is used in this work to develop a numerical model which predicts the change in yield strength of irradiated steels at various irradiation condition. More than 15,000 material related parameters such as composition, temperature, yield strengths are obtained from literature. These experimental results are used to generate more than 100 networks after proper training, testing and validation. A statistically validated neural network is used to predict the change in yield strength of RAFM steel in the range of 290 K − 900 K and 0 − 80 DPA. For instance, at 673 K and 300 K of test temperature and irradiation temperature, the yield is first found to increase and then remain constant after 50 DPA. Again at the same test temperature and higher irradiation temperature of 700 K, the yield strength is first found to increase till 25 – 30 DPA and then decreases thereafter. In the work we plan to present such kind of behavior at different temperatures and DPA conditions.

Speaker: Mr Agraj Abhishek (Institute for Plasma Research)

slide-summary.pdf

237 Characterization of Isotope Effect on Confinement of Dimensionally Similar NBI-Heated Plasmas in LHD

Energy confinement and thermal transport has been widely regarded as gyro-Bohm in tokamak as well as stellarator-heliotron for a single kind of ion. However, this gyro-Bohm model predicts confinement degradation in deuterium (D) plasmas because of larger normalized gyro radius than in hydrogen (H) plasmas, which conflicts with major experimental observations. This study aims to quantify a peculiarity in dependence on normalized gyro radius in H and D plasmas in order to address this unresolved issue. The first deuterium plasma campaign in LHD reveals definitive characteristics of isotope effect on NBI-heated plasmas from elaborated experiments. Stationary uneventful plasmas, which are accompanied by neither ITB nor transition, have been assessed here. Thermal energy confinement time gives the regression expression scaling with the isotope mass (A) as A to 0.15, which shows moderate improvement in D plasmas. This positive isotope dependence contradicts with gyro-Bohm and is similar to the recent result from L-mode plasmas in JET-ILW. Operational flexibility of magnetic field, density, and heating power enables adjustment of three major non-dimensional parameters, those being normalized gyro radii, collisionality and beta , and dimensionally similar plasmas of H and D in all these three parameters can be obtained. Then TASK3D-a / FIT3D is used for analysis of heating power deposition, power balance and local thermal transport. If gyro-Bohm nature predominates in these plasmas, thermal diffusivity normalized by Bohm diffusion should be the same in a pair of dimensionally similar plasmas of H and D. Different characteristics have been found in electron and ion loss channels. Electron heat diffusivity normalized by Bohm diffusion in H is lower than that in D and even lower by a factor of 1 over square root of 2 which means net improvement. This trend is robust and insensitive to parameters such as normalized gyro radii, collisionality, beta, scale length of density gradient, etc. In contrast, ion thermal diffusivity shows a same characteristics as in the electron channel in low collsionality regime while that in D compared with the case with H degrades with the increase of collsionality. These results have shown definitively that the gyro-Bohm nature is violated in the comparison of H and D plasmas in a large scale stellarator-heliotron.

Speaker: Prof. Hiroshi Yamada (National Institute for Fusion Science)

OnePageSlideEX_P3-5_YamadaH.pptx

238 Conceptual design of Neutron Activation System for IN-LLCB TBM

Neutron Activation System (NAS) is the primary neutron diagnostics for Indian Lead-Lithium Ceramic Breeder (LLCB) Test Blanket Module (TBM) in ITER. The main objective of NAS is to measure spatial distribution of neutron flux and energy spectra and in-situ measurement of tritium production rate inside the TBM. These measurements will be utilized for validation of neutron transport tools (software codes) and tritium breeding predictions used for breeding blanket systems design. NAS for LLCB TBM mainly consists of transfer station, capsule loader, transfer lines, foil gamma activity measurement system and irradiation ends. The irradiation of capsules consisting of foils is positioned inside the LLCB TBM at mid-plane location. The conceptual design of TBM along with NAS irradiation piping has been developed and its engineering design is in progress. All the components of NAS will be kept inside tritium building level L-2 of ITER building. The capsules are pneumatically transferred to irradiation end of piping located inside the TBM. After irradiation, the capsules are transferred back to counting station for foil activation measurement. This paper will present the conceptual design of NAS system along with preliminary engineering analysis and sequence of operations.

Speaker: Ms Shailja Tiwari (Institute for Plasma Research)

FIP-P3-28 -NAS summary.pptx

239 Contribution of fusion energy to low-carbon development under the Paris Agreement and accompanying uncertainties

The Paris Agreement requires deep reduction of greenhouse gas emissions. The world is toward rapid transition not only for climate change mitigation but also for sustainable development. Fusion energy has outstanding characteristics of plentiful resources, no nuclear runaway and zero-carbon emission, and its development has made a remarkable progress thanks to large investment for more than 50 years. However, long-term strategies for fusion energy development will become critically important in order to promote future DEMO projects by another large-scale investment and gain social acceptance. In this study, we assessed potential contribution of fusion energy to low-carbon development which is prescribed in the Paris Agreement under the combination of uncertainties of future socioeconomic development, the 2°C target and future commercial fusion power plants. We analyzed global energy systems up to 2100 in consideration of uncertainties by combining socioeconomic scenarios, global CO2 emission pathways, and fusion power plants by using a global energy systems model: DNE21+. We used three Shared Socioeconomic Pathways (SSPs) to express the uncertainty of future socioeconomic development. Assumptions and parameters for DNE21+ were harmonized with the SSP narratives. Four global CO2 emission pathways were used to simulate the uncertainty of the long-term targets of the Paris Agreement. For the uncertainty of fusion energy development, we set three scenarios, i.e., No Fusion, Conventional R&D and Advanced R&D which have different assumptions on parameters of fusion power plants. The parameters were set by considering potential and achievable cost reduction and performance improvement on the extension of DEMO concept design. Global negative CO2 emission in 2100 by drastic decarbonization of energy systems is required in order to achieve the 2°C target, and fusion power plants will be installed in the latter half of the 21st century mainly in the countries which have limited potentials of zero-emission energy sources such as Japan, Korea and Turkey. If inexpensive power plants could be developed by enhanced R&D and advanced design in DEMO projects, fusion power plants will also be deployed in the EU28, India and China. This study could be implicated in long-term strategy planning for fusion energy development.

Speaker: Dr Keii Gi (Research Institute of Innovative Technology for the Earth)

FEC2018_summary_gi.pdf

240 Core transport improvement in stable detachment with RMP application to the edge stochastic layer of LHD

Significant core plasma transport improvement is observed in the detachment divertor operation, which is stabilized by application of resonant magnetic perturbation (RMP) to the edge stochastic layer of LHD. Pressure profile becomes peaked and the heat transport coefficient,chi_eff, estimated from transport analysis, reduced in the entire confinement region. The RMP amplitude scan experiments show change of detachment transition density and of resulting chi_eff, while attained divertor particle flux reduction and radiated power are independent of the RMP amplitude. The results are new systematic study of RMP effects on detachment as well as on the core plasma transport. It suggests compatibility of good core plasma performance with divertor power load reduction in 3D magnetic field configuration with RMP application. Compatibility of good core plasma performance with enhanced edge radiation to mitigate the divertor power load is a crucial issue for magnetically confined fusion reactors. It is, however, commonly observed that the core confinement degrades with increasing radiation fraction. It is also not clear yet how RMP affects the core plasma transport during detachment, where no systematic RMP amplitude scan experiments have been performed so far in either tokamaks or stellarators in this respect. In LHD, stable detachment control is realized with RMP application of m/n=1/1 mode, where the core plasma transport is found to improve in the detached phase. The present paper reports, for the first time, analysis of the core transport, edge radiation, and divertor particle/power flux reduction with systematic scan of RMP amplitude (B_r/B_0). The RMP application creates a magnetic island of m/n=1/1 in the edge stochastic layer, where the impurity radiation is enhanced due to increased volume of cold plasma region. The divertor power and particle flux exhibit n=1 mode pattern in toroidal direction. With RMP application, the radiated power increases at lower density compared to the no-RMP case, and thus it results in earlier detachment transition. There appears a plateau region of radiation against density rise. This leads to a wide density operation range and thus provides a stable detachment control. RMP amplitude scan experiments show celar change of detachment transition density and resulting energy transport coefficients.

Speaker: Dr Masahiro Kobayashi (JpNIFS)

summary.pptx

241 Dependence of RMP penetration threshold on plasma parameters and ion species in helical plasmas

We investigate the penetration threshold of the RMP (Resonant Magnetic Perturbation) by the external coils in the LHD (Large Helical Device) for the various configurations. In a configuration of the LHD, it has qualitative similar dependence with that in Ohmic tokamak plasmas. However, the qualitative dependence on the collisionality is opposite to that in a high plasma aspect configuration, which is a quite unique property, and first found in the LHD. Also, we investigate the threshold on the ion species, and find that the threshold of deuterium is quite smaller than that of hydrogen. In the above cases, the RMP penetration thresholds are higher as the poloidal rotation is faster, which is qualitatively consistent with the torque balance model between the electro-magnetic and the poloidal neoclassical viscous torque.

Speaker: Dr Kiyomasa WATANABE (National Institute for Fusion Science)

4FEC2IAEA.pptx

242 Design and Simulation Studies of Calorimetric Dummy Load for Gyrotron System

High microwave power is generally measured and characterized by calorimetric dummy loads, which are designed to suit the exiting modes of the gyrotron / HPM. The output mode of the gyrotron is converted to a Gaussian mode-HE11 mode after passing through series of mode converters. The objective of this study is to design and fabrication of Calorimetric Dummy Load with efficient cooling medium which absorb maximum power of 200 kW at 42±0.2GHz frequency applied for 3 seconds, suited for microwave power propagating in HE11 mode. There is rigorous requirement of proper cooling channel or cooling medium over the dummy load system for the dissipation of heat in the quickest manner. As an effect of high microwave energy (maximum heat), internal heat buildup in the dummy load system which could results in a catastrophic failure or decrease in the life span of the dummy load. This research envisaged the thermal effect of microwave energy on a reflecting structure incorporated to transfer microwave energy to heat absorber media concatenating the effect of heat conduction via multi flow path technique. In this manuscript, CFD analysis using ANSYS has been carried out to find the temperature contour, velocity contour, pressure contour for water passing through the helical tubes and thermal analysis has also been carried out for reflecting medium and microwave absorber material inside the enclosure. Details of these analyses results and their optimizations will be discussed in this paper.

Speakers: Mr Axat Patel (Assistant Professor), Mr Maulik Shah (Assistant Professor)

IAEA_FIP_P3_62.pptx

243 Design Progress of Advanced Fusion Neutron Source for JA/DEMO Fusion Reactor

Based on results from the IFMIF/EVEDA project in the Broader Approach (BA) activities, a conceptual design of the Advanced Fusion Neutron Source (A-FNS) in Rokkasho aiming at obtaining material irradiation data up to 20 dpa for a fusion DEMO reactor is presented in this paper. The A-FNS is composed of an accelerator facility with a 40 MeV and 125 mA deuteron beam, a test facility and a post irradiation examination facility. A particular attention in the design is paid on an integration of the test facilities by adopting a newly designed test specimen module for A-FNS. Recently, the nuclear analysis of test module has been progressed to optimize the irradiation of test pieces and then it was clarified that our original module enabled the test pieces to be irradiated uniformly.

Speaker: Dr Kentaro Ochiai (QST)

244 Deuteron Beam Commissioning of the Linear IFMIF Prototype Accelerator Source and LEBT

The Linear IFMIF Prototype Accelerator aims to operate in Rokkasho Fusion Institute a 125 mA/cw deuteron beam at 9 MeV In order to prove the technical feasibility of the IFMIF accelerators concept.

A 2.45 GHz ECR ion source developed by CEA-Saclay is designed to deliver 140 mA/100 keV CW D + beam. The low energy beam transfer line (LEBT) relies on a dual solenoid focusing system to transport and match the beam into the next accelerating section which is a Radio-Frequency Quadrupole (RFQ). At the end of the LEBT, the normalized RMS emittance has to be lower than 0.3$\pi$ mm.mrad in order to reach the optimal beam transmission through the RFQ.

This contribution will present the different commissioning phases of LIPAC ion source and LEBT. The experimental results that have been obtained will be reported. In particular, beam emittance measurements as a function of ion source extraction voltage gaps, total extracted current from the source and solenoid tunings will be showed.

In order to model as well as possible the beam transport thought LEBT, intensive beam dynamics simulations that take into account space charge compensation have been performed using a self-consistent particle-in-cell code. Simulation results will be discussed and compared to experimental data.

Speaker: Dr Masayoshi Sugimoto (JpQSTRFI)

245 Development and Qualification of Passive Active Multijunction (PAM) Launcher for LHCD System of ADITYA -Upgrade Tokamak

A Passive Active Multijunction (PAM) antenna is designed and developed and would be commissioned on the ADITYA-U tokamak. The PAM antenna has many advantages over the grill antenna such as exhibiting a lower reflection coefficient at the plasma densities close to its corresponding cut-off density. The PAM antenna along with its transmission line components are designed to deliver RF power up to 250 kW for 1 second and its design is validated using COMSOL Multiphysics and CST studio. This paper describes the fabrication protocols of each component of the PAM launcher and its transmission line components along with its low power test methodology.

Speaker: Mr Yogesh Jain (Institute for Plasma Research, HBNI)

FIP-P3_53_Yogesh_Jain_Summary_slide.pdf

246 Development of HINEG and its experimental campaigns

A high intensity D-T fusion neutron generator is an important experimental platform for research and development (R&D) of nuclear energy and nuclear technology applications. High Intensity D-T Fusion Neutron Generator (HINEG) has been developed by the Institute of Nuclear Energy Safety Technology (INEST), Chinese Academy of Sciences (CAS)/FDS team to perform researches on fusion nuclear technology and safety including validation of neutronics theory and software, neutronics performance of blanket/reactor, materials irradiation damage mechanism, etc. Also, the application of HINEG can be extended to neutron radiography, neutron radiotherapy, and so on. The R&D of HINEG includes three phases: HINEG-I has been finished, and successfully produced the D-T fusion neutrons with the yield up to 6.4*10^12 n/s. Meanwhile, HINEG-I has been operated to drive the Lead-based Zero Power Critical/Subcritical Reactor CLEAR-0. HINEG-II aims at a high neutron yield of 10^15~10^16 n/s and the R&D for key components is on-going. HINEG-III is designed as a volumetric fusion neutron source with neutron yield of 10^18 n/s, which is based on the gas dynamic trap. Recently, a series of experiments have been carried out on HINEG facility by FDS team, such as neutronics performances of fusion reactor blanket, biological effects of neutron irradiation, fast neutron radiography, and so on. A dual function lithium-lead (DFLL) test blanket module (TBM) has been developed by FDS team to demonstrate the technologies of the liquid lithium–lead breeder blankets. The neutronics experiment of DFLL-TBM mockup was carried out to validate the tritium breeding and shielding performances. The comparison of experiment results and corresponding calculation performed using SuperMC and FENDL3.1 library was obtained, and a good agreement was observed between the experimental and calculated values. This presentation will introduce the R&D activities as well as the experimental campaigns of HINEG.

Speaker: Prof. Jieqiong Jiang (Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui, 230031, China)

One slide summary for FIP P3-40.pdf

247 Development of RF based capacitively-coupled plasma system for deposition of tungsten nano layers on graphite

Based on the current trends in thermonuclear fusion research, it is quite likely that future fusion machines, DEMO and beyond, will be operating with tungsten and alloys based on tungsten as the plasma facing material on their walls and targets to dissipate the thermal as well as particle loads under extreme conditions. Tungsten is being preferred because of its superior thermo-mechanical properties as well as for its low tritium retention. However, use of pure tungsten as a structural material itself will substantially increase the manufacturing cost and overall system mass and also it is difficult to machine. Hence, tungsten coatings on light substrate such as graphite are preferred which essentially reduce the cost and structural weight considerably. In this article, we report the development of a RF based capacitively coupled plasma reactor for tungsten coating on graphite tiles using plasma assisted chemical vapour deposition at SVITS, India. Tungsten nano layers have been successfully deposited on graphite test pieces by reducing the heavy tungsten hexafluoride gas in hydrogen. Characterization and post analysis of the tungsten coated tiles has been carried out to study the presence of tungsten, thickness of the coating, thermal fatigue etc.

Speaker: Mr Sachin S. Chauhan (Department of Physics, Shri Vaishnav Institute of Technology and Science, Indore, India)

FEC.pptx

248 Development of Technology for Fabrication of Prototype Ion Extraction Grid for Fusion Research

Steady state Superconducting Tokamak (SST-1) has a provision for positive hydrogen ion based Neutral Beam Injector (NBI) to raise the tokamak plasma ion temperature ~ 1 keV with neutral hydrogen beam (Ho) power of 0.5 MW at 30 kV. Heart of NBI system is ion extractor system which consists of three grids each made up of OFHC copper. The beamlets originating from the extractor system is focused horizontally at 5.4 mm and vertically at 7 mm to reduce power dissipation at beam line components. The required beam divergence is < 1o. For long pulse operation, active water cooling is provided by an in-laid dense network of 22 wavy semi-circular (r = 1.1±0.05 mm) cooling channels in the space available between the apertures. The required flatness of the copper plate is 100 µm and positioning tolerance of aperture is ±60 µm. All these stringent requirements dictates that fabrication of extractor grid is very complex process as it involves several critical technology e.g., (i) joining of SS304L stub rod with OFHC copper grid plate (ii) precision CNC etc. machining on large size OFHC copper plate for making shaped apertures and (iii) copper electroforming for fabrication of embedded cooling channels inside thin OFHC copper plate. None of these technologies are available in India. This paper describes the work done on prototype activities to gain experience in each of the above-mentioned technology areas. Friction welding (FW) is developed for joining of dissimilar metals of SS304L rod with OFHC copper plate with joining strength of 264 MPa. Then FW on actual size of OFHC copper plate is successfully done. Critical tolerances required for CNC machining for drilling and shaping of apertures and milling in thickness of OFHC copper grid plate of size 180 mm ´ 90 mm with 19 nos. of holes and 4 nos. of wavy semicircular cooling channel. Copper electro-deposition of 2.5 mm thickness is done on the above-mentioned prototype grid sample using technique of periodic reversal process where 20 sec electro-deposition was followed by a 4 sec reversal. Test specimens were also electro-deposited along with the prototype grid plate for testing of mechanical properties and conductivity. The conductivity was 101± 1 % IACS with micro hardness values 56 to 61 HV5. All these experiences shall be useful for manufacturing of large size ion extractor grid in India.

Speaker: Dr Mukti Ranjan Jana (Institute for Plasma Research)

Summary slide-M R JANA.pdf

249 Dispersion Strengthened Copper Alloys Produced by Mechanical Alloying and Hot Isostatic Pressing for Divertor Application

The realization of advanced fusion reactors rests with improvement of cooling capacity of divertors. Enhancing mechanical properties of Cu alloys is one of the critical issues for the improvement. This paper reports development of dispersion strengthened Cu alloys using ball-milling, encapsulation, and Hot Isostatic Pressing (HIP) facilities. Cu-Al, Zr and Y alloys have been produced so far. The new facilities installed in NIFS made it possible to control oxygen level of the products. In the case of Cu-Y, CuO was added in the middle of the milling for supplying oxygen. These processes resulted in formation of fine microstructures, oxide dispersion, and significant strengthening of Cu alloys.

Speaker: Dr Hiroyuki Noto (National Institute for Fusion Science)

Presentation Materials_Hiroyuki Noto.pptx

Presentation Materials_Hiroyuki Noto_rev.pptx

250 Effect of deuterium plasmas on carbon impurity transport in the edge stochastic magnetic field layer of Large Helical Device

Stochastization of edge magnetic fields has been extensively studied not only for the ELM mitigation but also for the plasma detachment and the impurity transport. The ergodic layer of Large Helical Device (LHD) consists of stochastic magnetic fields with three-dimensional structure intrinsically formed by helical coils. Reduction of the parallel impurity transport in the ergodic layer, so called “impurity screening”, has been studied in LHD. The theoretical modelling explains that the parallel momentum balance on impurity ions determines the direction and quantity of the impurity flow driving the impurity screening. Recently, the carbon flow in the ergodic layer was measured in hydrogen (H) plasmas with space-resolved vacuum ultraviolet (VUV) spectroscopy and a close relation between the impurity flow and the impurity screening was experimentally verified for the first time by the comparison between the spectroscopic observations and the impurity transport simulation based on a three-dimensional simulation code, EMC3-EIRENE. In the present report, the VUV spectroscopy for carbon impurities is applied to deuterium (D) plasmas to clarify the effect of the bulk ion mass on the impurity transport in the ergodic layer. Doppler profile measurement at the second order of CIV line emission (2 × 1548.20 Å) is attempted in a flat-top phase of discharges using a 3 m normal incidence VUV spectrometer in the edge plasma at a horizontally-elongated plasma position. The flow velocity becomes the maximum value at the position close to the outermost region of the ergodic layer. The direction of the observed flow is same as the friction force in the parallel momentum balance calculated with EMC3-EIRENE code. The flow velocity increases with the electron density in the H plasmas. The result supports a prediction from the simulation that the friction force becomes more dominant in the force balance in higher density regime. It leads to the increase in the impurity flow which can develop the impurity screening. On the other hand, the flow velocity in the D plasma is smaller than that in the H plasma. The difference of the flow values between D and H plasmas is caused by the mass dependence of the thermal velocity of the bulk ions when the friction force term is dominant in the force balance.

Speaker: Dr Tetsutarou Oishi (National Institute for Fusion Science)

IAEA2018_Summary_EX_P3-11_Oishi.pdf

251 Effect of magnetic field on the corrosion behavior of Indian RAFMS in liquid Pb-Li

In the present study, the effect of magnetic field on the corrosion of Indian Reduced Activation Ferritic Martensitic Steel (IN RAFMS) in flowing lead lthium eutectic (Pb-Li) has been studied in an electromagnetic pump driven loop (EMPPIL-M). The corrosion rate in the presence of of 0.5 KG magnetic field at a temperature of 773 K has been found to be 1.3 times higher than that observed in the absence of magnetic field. The surface of the IN RAFMS sample located inside the magnetic field showed non uniform corroison and formation of distict surface features which were revealed through optical and secondary electron (SE) micrographs. The Pb-Li attack in the presence of magnetic field was not only confined to the prior austenite and lath boundaries as in the absence of magnetic field; but also happened in the intra-lath regions causing formation of subgrains. The change in Pb-Li flow profile due to magneto-hydrodynamic effect is expected to play a major role in the formation of surface features, non uniformity in surface attack and increased corrosion rates in the presence of magnetic field. The detailed discussion on the results obtained from analysis of the exposed samples through various charachterisation techniques (stereomicroscope, optical profilometry, secondary electron microscopy-energy dispersive spectroscopy [SEM-EDS], etc) will be presented in this paper.

Speaker: Mrs Poulami Chakraborty (Bhabha Atomic Research Centre, India)

summary slide_FEC_PCS.pdf

252 Effect of magnetic field structure on electron internal transport barrier and its role for the barrier formation in Heliotron J

The effects of magnetic field topology on an electron internal transport barrier (eITB) and on its formation in the helical plasma are discussed in this paper. In helical plasmas, the eITB can be formed by generation of the positive radial electric field with electron cyclotron resonance heating due to the electron-root transition that is related to the neoclassical transport through the helical ripple. A hypothesis of the eITB formation is that the barrier is easily formed in larger helical ripple ($\epsilon_{eff}$) magnetic configuration. In Heliotron J, however, although the high and low bumpiness configurations have higher $\epsilon_{eff}$ compared to the medium bumpiness configuration, the power thresholds to form the eITB in the low and high bumpiness configurations are larger ($\sim 550\times 10^{-19} kWm^{3}$) than that of the medium bumpiness ($\sim250\times 10^{-19} kWm^{3}$). This result shows that the eITB formation is not determined by $\epsilon_{eff}$ alone. Next, we have investigated the effect of the magnetic topology on the eITB formation. The first result is that the correlated behaviors of the eITB foot point and the low-order rational surface location are observed. The former shows a jump at $I_p\sim 0.7 kA$ and a subsequent outward shift by the current increase. The estimated 4/7 rational surface appears at the value of $\sim0.7 kA$, then it moves outward with the increase of the bootstrap current. The second result is that the power threshold for the eTIB formation is reduced from $265 \times 10^{-19}kWm^3$ to $240 \times 10^{-19}kWm^3$ when the plasma current increases above $I_p\sim0.9 kA$, of which value is almost the same as the calculated value that is required to form 4/7 rational surface. Because the 4/7 rational surface is a candidate on which the magnetic island can be formed due to the n=4 toroidal periodicity of the vacuum magnetic field, and other low-order rational surfaces have no contribution to these phenomena, the results show the possibility that the formation of the magnetic island can expand the improved confinement region or reduce the power threshold for the eITB formation. The similar mechanism that the magnetic island affects the plasma transport has been also observed in numerical simulation. It is necessary to consider not only neoclassical transport effect but also magnetic island effect on the eITB formation.

Speaker: Dr Takashi Minami (Institute of Advanced Energy, Kyoto University)

SummarySlides_TMnamiV2.pdf

Summary Slides SummarySlides_TMnamiV2.pdf

253 Effect of Simulated Post Weld Heat Treatment on the Microstructure and Mechanical Properties of IN-RAFM Steel

Indigenously developed India specific Reduced Activation Ferritic/Martensitic (IN-RAFM) steels are currently considered as a structural material for the Indian Lead Lithium cooled Ceramic Breeder Test Blanket Module (IN-LLCB TBM). Advanced ferritic/martensitic steels offer the opportunity for improvements in fusion reactor performance, operational lifetime and reliability, superior neutron radiation damage resistance, higher thermodynamic efficiency and reduced construction costs. Typically RAFM steels are normalized at high temperature i.e. 980oC for 30 minutes followed by low temperature tempering for longer duration i.e. 760oC for 90 minutes. The resulting microstructure determines the mechanical properties of the steel. These microstructures are designed to produce an optimum combination of strength and toughness at high temperature. However, situations may arise in practice, particularly during welding operations for example, whereby the RAFM steel may receive an additional heat treatment which briefly exceeds the Ac1 and possibly the Ac3 temperature before stabilizing at the tempering temperature. To restore the properties of the weld joints, post weld heat treatment (PWHT) is applied to the steel at 750oC for 2 hours followed by furnace cooling. During PWHT, the base or parent metal of the RAFM steel weld joints also undergo heat treatment process. In this present investigation, the consequence of PWHT effect on base metal of IN-RAFM steel is studied. Simulated post weld heat treatments (SPWHT) have been applied to IN-RAFM steel in a muffle furnace at 750oC and 770 oC for 2 hours followed by cooling inside the furnace. Hardness measurements were carried out on the heat treated sample and was found to be ~210 HVN which is comparable with base metal hardness properties. Advanced electron microscopy has been carried out to investigate the effect of the SPWHT excursions on subsequent microstructural evolution. Tensile tests have been carried out on SPWHT specimens at various temperatures from room temperature to 600 oC. Tensile properties of SPWHT specimen at room temperature is ~650 MPa and at 550 oC is ~320 MPa. Impact toughness upto -100 oC are also being evaluated in this present investigation. The results discuss the effect of SPWHT on mechanical properties of RAFM steel during high temperature service.

Speaker: Mr Chandra Sekhar Sasmal (Institute for Plasma Research)

Summary Slide_Effect of SPWHT on mechanical properties of IN-RAFMS.pptx

254 Effect of sorbent selection and geometrical arrangement of cryopanels on pumping speed of cryopump

Vacuum is an inherent part of any Fusion machine. The requirement of providing large pumping speed is growing as fusion science is progressing towards high temperature, high density, and large confinement machines. In its domestic programme of development of technologies for Fusion grade machines, Institute for Plasma research (IPR) developed the sorbent based cryopumps. Using coconut shell charcoal pumping speed of 2 l/s/cm2 for helium and 5 l/s/cm2 for hydrogen is demonstrated. Different sorbents are under study for their performance of pumping speed, for example carbon cloth and flocked carbon panels. Experimental study of pumping speed is being carried for different geometrical configurations of panel arrangements. MOLFLOW+ is used for simulating the pumping speed. Initial experiments are being carried out at 80 K and compared with MOLFLOW+ results. This paper discusses in detail simulation and experimental results of developed pumps

Speaker: Ms Ranjana Gangradey (Institute for Plasma Research)

255 Electron Bernstein Wave Heating and Current Drive with Multi-Electron Cyclotron Resonances During Non-inductive Start-up on LATE

Electron cyclotron heating and current drive (ECH/ECCD) by electron Bernstein waves (EBWs) with multi-electron cyclotron resonances (ECRs) is carried out by injecting microwaves at two frequencies during the non-inductive start-up of a spherical tokamak (ST) . When the 2nd EBW at 5 GHz is excited in the non-inductively produced ST plasma with the 1st EBW at 2.45 GHz, plasma current is driven strongly while the bulk electron parameters such as density are nearly the same. The 2nd EBW is absorbed mainly by high energy tail electrons between the 2nd ECR layer and the upper-hybrid resonance (UHR) layer by Doppler effect and drive the plasma current, while the 1st EBW sustains the bulk electrons.

Speaker: Prof. Hitoshi Tanaka (Kyoto University)

summary-presentation-2018.pdf

256 Energetic-ion Confinement Studies by using Comprehensive Neutron Diagnostics in the Large Helical Device

Study on neoclassical and anomalous transport of energetic particle (EP) in the Large Helical Device (LHD) has been performed by means of escaping EP diagnostics. By starting deuterium operation of the LHD, confinement study of EPs has remarkably progressed by using newly developed comprehensive neutron diagnostics providing the information of EPs confined in the core region. Time evolution of total neutron emission rate ($S_n$) following the short pulse neutral beam (NB) injection is reproduced by drift kinetic simulation, indicating that beam ion transport can be described with neoclassical models. The vertical neutron camera (VNC) works successfully, demonstrating that neutron emission profile shifts according to magnetic axis position ($R_{ax}$). Correlated with helically-trapped EP driven resistive interchange mode (EIC) burst, substantial drop of ($S_n$) and change of neutron emission profile are observed, indicating the significant loss of helically-trapped beam ion due to the EIC mode. Time-resolved triton burnup study is performed for the first time in stellarator/heliotron so as to understand the alpha particle confinement. It is found that the triton burnup ratio which largely increases at inward shifted configurations is similar to that measured in tokamak having a similar minor radius with the LHD. We demonstrate the confinement capability of EPs toward a helical reactor and expansion of the energetic-ion physics study in toroidal fusion plasmas.

Speaker: Dr Kunihiro Ogawa (National Institute for Fusion Science)

180927_IAEAFEC_ko_r0.pdf

257 Energy differential and displacement damage cross section of DT neutron induced reactions on fusion reactor materials (Fe, Cr & W)

Displacement per atom (dpa) in fusion reactor materials are essential designing parameters to ensure the reliable functioning and structural integrity of fusion reactor components. All probable reaction channels such as (n,n’), (n,2n), (n,p), (n,α) and (n,d) are open for the interactions of D-T neutrons of 14.1 MeV energy with the fusion reactor material. Evaluation of dpa requires energy spectra of recoil nuclei for each reaction channel. The iron, chromium, and tungsten are important materials widely proposed for structural and first wall components of the reactor. TALYS 1.8 and Empire3.2 codes have been used to calculate cross-section data and recoil spectra for each reaction channel. In the cross-section and spectra calculations, Contribution from all possible reaction mechanism such as direct, pre-equilibrium, compound and multiple emission reaction mechanisms have been considered. Prediction of σDPA requires energy differential cross section (EDX) of recoil nuclei from each reaction channel. EDX of emitted charged particles have been predicted and compared with the existing evaluated and experimental data from IAEA data Libraries to select the best fitted nuclear models and parameters. Energy spectra of recoil nuclei also considered as primary knock-on atoms for each reaction channel, have been predicted using the appropriate nuclear models and parameters in TALYS code for incident neutrons up to 15 MeV energy. PKA data have been used in NRT (Norgett Robinson and Torren), BCA (Binary collision approximation), BCA+MD (molecular dynamics) and kinetic monte carlo methods. Predicted σdpa is compared with the existing database of σdpa, prepared using the NJOY code. EDX data of each reaction channels are calculated for all stable isotope of Fe(54Fe, 56Fe, 57Fe, 58Fe), Cr(50Cr, 52Cr, 53Cr, 54Cr), and W(182W, 182W, 183W, 184W, 186W) and used for the prediction of σdpa for natural elements. For the experiments of DDX measurement of charged particles, neutron flux is measured with the diamond detector (efficiency = 0.00109% for the D-T neutrons). The efficiency of diamond detector has been measured with the alpha counting method using silicon surface barrier detector. Experiments for the DDX measurements are being carried out for natural iron and chromium.

Speaker: Mr Mayank Rajput (Institute for Plasma Research)

Summery.pdf

258 Er2O3 Coating by Multilayer Metallic Sputtering and Intermediate Oxidation Approach

Er2O3 (erbia) is a leading candidate for hydrogen isotope barrier and electrical insulation coating application in some sub-systems of advanced nuclear fusion research reactor designs. Due to harsh environment of the reactor, structural and microstructural stability of the coatings at elevated temperature is critical. The polymorphs of erbia are reported in cubic, monoclinic and hexagonal phases depending on the ambience of the formation. Cubic is the most stable phase among these as it does not transform up to 2327 C. Hence, it is important to choose and tune the deposition process so as to obtain cubic phase Er2O3 coatings with dense packed and compact microstructure. Our previous study conclusively showed that reactive sputter deposition leads either to a coating with monoclinic phase and compact microstructure or to cubic phase and cracked/bulged microstructure, depending on the process temperature. Also inferred from the study was that metallic Erbium deposition converts into cubic phase upon post oxidation. Hence, a novel approach of depositing thin multilayers (~40 nm) of Erbium with intermediate in-situ oxidation has been adopted in this work. The structural phases and microstructure of the deposited films are studied using X-Ray Diffraction (XRD), Grazing Incidence Diffraction (GID) and Scanning Electron Microscope (SEM). The variation in these properties is correlated with the variation in process parameters such as layer thickness, oxidation duration, temperature, post annealing, etc. The detailed results of this study in comparison to those of reactive sputter deposition will be presented in this paper. References: [1] P. A. Rayjada, “Study of Er2O3 Film Deposition by Different Techniques for the Fusion Reactor Applications” Ph. D. thesis, Sardar Patel University, Vallabh Vidyanagar, January, 2017 (http://shodhganga.inflibnet.ac.in/handle/10603/146486) [2] P. A. Rayjada, N. P. Vaghela, N. L. Chauhan, A. Sircar, E. Rajendrakumar, L. M. Manocha, P. M. Raole, Fusion Science and Technology, 65 (2014), 194. [3] P.A. Rayjada, N.P. Vaghela, R. Rahman, M. Bhatnagar, M. Ranjan, N.L. Chauhan, Amit Sircar, L.M. Manocha, P.M. Raole, Nuclear Materials and Energy, 9 (2016), 256–260, http://dx.doi.org/10.1016/j.nme.2016.05.011

Speaker: Dr Pratipalsinh A. Rayjada (Institute for Plasma Research)

259 Evaluation of Beam Properties of a Negative Hydrogen Source by Doppler Shift Spectroscopy

ROBIN (RF Operated Beam source in India for Negative Ion research) is a negative H- ion source, which is operational in IPR, Gandhinagar. For measurement of various beam parameters such as beam energy, beam divergence, beam homogeneity and the stripping losses, Doppler Shifted spectroscopy diagnostics was established on ROBIN. The beam properties are studied by varying the source pressure (0.3-0.6 Pa), RF power (30 kW-60kW), tank pressure (7 x 10-4 mbar – 5 x 10-5 mbar), the total applied voltage in the range of 7kV-24kV has been carried out. The beam divergence and stripping losses are estimated from the line profiles analysis of the observed Doppler shift spectrum. The homogeneity of the beam in the vertical direction has been evaluated by using eight lines of sight located at two symmetrical locations in the ROBIN test vessel. The effect of space charge compensation on beam divergence has also been studied by varying the test stand pressure. The observed beam divergence is found to be lower at lower applied voltages and started increasing monotonically with an increase in voltage. The beam divergence is found to be decreasing with increase in RF power. The stripping losses are higher at lower voltages and start decreasing with increase in applied voltage. The beam is more uniform in the upper portion in comparison with the lower portion. In this present work, the parametric evaluation of the beam properties is presented in detail and results are discussed.

Speaker: Mr Arnab Jyoti Deka (Institute for Plasma Research)

Summary Slide – Arnab.pptx

260 Experimental analysis of self-organized structure and transport on magnetospheric plasma device RT-1

The dipole plasma exhibits strong heterogeneities in field strength, density, temperature, etc., while maintaining the holistic balance. Enquiring into the internal structures, we reveal the fundamental self-organizing mechanisms operating in their simplest realization (as commonly observed in astronomical systems) [1, 2]. Three new findings are reported from the RT-1 experiment: (i) Creation of a high-energy electron core (similar to the radiation belts in planetary magnetospheres) is observed for the first time in a laboratory system. High-energy electrons (3 - 15keV), produced by an electron cyclotron heating (ECH), accumulate in a “belt” located in the low density region (high-beta value ~ 1 is obtained by increasing the high-energy component up to 70% of the total electrons). (ii) The dynamical process of the “inward diffusion” (a spontaneous mechanism of creating density gradient) has been analyzed by perturbing the density by gas injection. (iii) By a system of coherence-imaging spectroscopy, the profiles of the ion temperature and flow velocity have been measured. The effect of the ion cyclotron resonance frequency (ICRF) heating [3] has been visualized. These results advance our understanding of transport and self-organization not only in dipole plasmas, but also in general magnetic confinement systems relevant to fusion plasmas. [1] A. Hasegawa, Comments Plasma Phys. Contr. Fusion 1 (1987) 147. [2] Z. Yoshida, Adv. Phys. X 1 (2016) 2. [3] M. Nishiura et al., Nucl. Fusion 57 (2017) 086038.

Speaker: Dr Masaki Nishiura (The University of Tokyo)

abstract_nishiura.pdf

261 Experimental Studies of Plasmoid Reconnection for Closed Flux Current Generated by Coaxial Helicity Injection on HIST

The Spherical Torus (ST) is a leading candidate for an advanced fusion reactor due to its compactness. Transient coaxial helicity injection (T-CHI) is one of CHI schemes, and it is used to generate and ramp-up the plasma current at the initial phase of a discharge. One of the most important issues in T-CHI is whether it can establish a current sufficient for succeeding current drive and heating. Understanding the fast reconnection mechanism for the flux closure during the start-up process is the primary purpose of the T-CHI experiment on Helicity Injected Spherical Torus (HIST: R=0.30 m, a=0.24 m, A=1.25). The fast reconnection driven by plasmoid for the flux closure has been demonstrated by T-CHI in the HIST device. The intensive measurement of internal magnetic structures indicates that two or three plasmoids are generated in an elongated Sweet-Parker current sheet during the T-CHI. Here, we report that in the T-CHI start-up plasmas, (i) the observed regular oscillations of magnetic field, electron density and ion flow indicate repetitive generation of small-size plasmoids due to the magnetic reconnection, (ii) one of plasmoids grows up to a large-size, and a doublet-type ST configurations is formed as a result. Consequently, the plasmoid reconnection could be the leading mechanism for the formation of multiple X-point, i.e., the fast flux closure in the T-CHI dicharge.

Speaker: Prof. Masayoshi Nagata (University of Hyogo)

2018 IAEA-FEC EXP-17_M.Nagata.pptx

262 Extent of Tritium Contamination of Helium Circuit in a Fusion Reactor- probable scenarios

In the presently available fusion reactors, cryogenic helium is an integral part for cooling the magnets in order to achieve super conductivity. Some of the fusion reactors use tritium as a nuclear fuel along with deuterium, in which a part of tritium is proposed to be breeded through lithium blanket covering the first wall of plasma. Since fusion reactors have very small burn up efficiencies (~ 0.3 to 2 % only), a very small amount of fuel is consumed and majority of the unburnt fuel is required to be pumped out and is reprocessed for subsequent cycles. Due to the magnetic and neutronic environment prevailing inside the fusion reactor, for the evacuation of the vacuum vessel, cryo-pumps are the suitable choice as compared to other available options. Cryo-pumps provide cooled surface of charcoal as an adsorber bed to trap the gaseous molecules. The adsorber beds are cooled down to 5K with the help of cryogenic liquid helium being supplied from the cryo-plant with an intermediate cold box in order to provide better controllability. The contamination of cryogenic helium with tritium arises in the cryo-pumps and may be extended to the cryo-plant. Thus are possible scenarios where the hand-shaking of tritium with cryogenic helium is possible thereby posing a threat to cryogenic plant safety depending on the extent of tritium contamination of cryogenic fluid and hence is required to be analyzed while designing the system. The tritium impact on cryo-plant design in the presently available tokamaks (such as ITER, etc.) has not been taken into consideration in the design as the amount of tritium permeated through stainless steel to cryogenic helium, through cryo-pumps, is not substantial. But for future fusion reactors where the amount of tritium to be handled would be substantial, the threat can’t be evaded. This leads to open a new area of research in the context of design of cryo-plants for future fusion reactors.
The present study throws light on the possible scenario and mechanism of tritium diffusion along with the extent of contamination and its validation through available experimental data. This study will also be helpful for design of the cryo-plants for future fusion commercial reactors.

Speaker: Mr Vinit Shukla (ITER-India, IPR)

Summary slide.pptx

263 Fluctuation suppression by the potential formation in GAMMA 10/PDX plasma

In the hot ion mode experiments of the tandem mirror GAMMA 10/PDX plasma, the suppression of drift-type fluctuation, which rotate in the direction of the electron diamagnetic drift, has been observed when the axial confinement potential is formed by the electron cyclotron heating (ECH) at the barrier (B) and plug (P) cells. The flute-type fluctuation of which rotation direction is the same as ion diamagnetic rotation direction was also suppressed with application of both B/P-ECH for the first time. The suppression seems to be caused by ExB drift shear, which is common in magnetically confined fusion plasmas. Fluctuation study is one of the most important issues in magnetically confined fusion plasmas, because the fluctuations due to the instabilities cause the anomalous transports. The drift-type fluctuation arises due to the existence of density and temperature gradients. The radial electric field E causes an E×B plasma rotation in the direction of the ion diamagnetic rotation, which may enhance instabilities such as rotational flute modes, and degrade radial confinement. In the tandem mirror GAMMA 10/PDX, the main plasma is produced and heated by ion cyclotron range of frequency (ICRF) waves, and an electrostatic potential for improving an axial confinement is created by applying electron cyclotron resonance heating (ECH) in the end mirrors of barrier/plug (B/P) cells. The plasma confinement is improved not only by a magnetic mirror configuration but also by high potentials at both end mirrors. The typical electron density, electron and ion temperatures are about 2 × 10^18 m^-3, 0.1 keV and 5 keV, respectively. We often observed flute-type fluctuations and they seem to be related to E×B drift. In order to clarify the E×B drift effects on flute-type fluctuations, we optimized the diameters of iris-limiters, fueling gas pressures, and ICRF heating powers to produce the rotational flute-type fluctuation before B/P-ECH. The central potential quickly increased and the observed fluctuations on the line density and potential were clearly suppressed by the application of B/P-ECH. Potential and density fluctuations suppressions with the application of B/P-ECH were clearly observed at each radial position. Low frequency flute-type fluctuations in the density and potential were suppressed with applying B/P-ECH for the first time.

Speaker: Dr Masayuki Yoshikawa (University of Tsukuba)

EX_P3-1_Yoshikawa.pdf

264 Fully Non-inductive 2nd Harmonic Electron Cyclotron Current Ramp-up with Focused Polarized Beams in the QUEST Spherical Tokamak

A transmission line and a launcher system have been newly developed to conduct the second (2nd) harmonic electron cyclotron (EC) plasma ramp-up with an eXtra-ordinary mode wave in the QUEST spherical tokamak. The incident elliptical polarizations were controlled with two corrugated (quarter/one-eighth wavelength) polarizers. The launcher system with two quasi-optical mirrors produced a sharply focused incident beam with a waist size of 0.05 m at the 2nd electron cyclotron resonance layer. The obtained electron density was one order of magnitude higher, compared to the previous experiments with no polarized focusing-beam. As a new record of non-inductive plasma ramp-up with EC-waves, a highest plasma current of 86 kA was achieved with a focused 230 kW 28GHz-beam. The record plasma current ramp-up efficiency on the incident power in the 2nd harmonic EC scenario was also achieved.

Speaker: Dr Hiroshi Idei (Research Institute for Applied Mechanics, Kyushu University)

1page_Ex_P3_21.pptx

265 Global supply of tritium for fusion R&D

The tritium start-up inventory required by a tritium self-sufficient DEMO-class fusion reactor is subject to a wide margin of uncertainty, with estimates in the literature varying from less than 1 kg to almost 20 kg for a ~2 GW fusion reactor. If ITER is successful, it is conceivable that multiple DEMO-class devices may be developed in parallel; the European DEMO machine, the Chinese Fusion Engineering Test Reactor and others could require several kilograms of tritium each in the 2050s. Tritium production from heavy water (D2O) CANDU reactors in Canada presently meets the entire fusion R&D demand of tritium. Ontario Power Generation (OPG) plans to supply ITER with all of the tritium required for its exploitation. Yet OPG may only be able to supply up to 8 kg for a DEMO reactor in the mid-2050s, following the delay to the ITER D-T operations (now scheduled in 2036), owing to the progressive phasing out of Canadian CANDU reactors in the 2030s and the natural decay of stocks. There is a risk that commercially available tritium stockpiles in the 2050s are insufficient to meet the fusion demand. Herein, we present several data-based scenarios of tritium production from heavy water reactors (HWRs) and fusion tritium consumption with varying degrees of optimism. At present, only Canada and the Republic of Korea actively extract tritium from their HWRs in tritium extraction facilities (TEFs), and Romania plans to build one. Based on the assumption that only these countries contribute to the global supply of commercially available tritium, results range from 0 kg to 30.5 kg of T available in 2055, depending on the scenario considered. Alternative methods for tritium production are discussed; D-D fusion start-up with a breeding blanket, modifications to CANDU reactors and other HWRs, and production of tritium in commercial light water reactors using tritium-producing burnable absorber rods. Tritium production in HWRs remains the best source of tritium for fusion R&D. If Canada, the Republic of Korea, and Romania supply the fusion community with their HWR tritium, there is a reasonable chance that 10 kg of T would be available for fusion R&D in 2055. We call attention to the dependency of the fusion community on events outside its control, most critically the refurbishment of existing HWRs and TEFs, and the construction of new ones in several countries.

Speaker: Mr Matti Coleman (CCFE)

266 Investigation of fine structure formation of guide field reconnection during merging plasma startup of spherical tokamak in TS-3U

We present the latest results of high-resolution 2D imaging measurement of merging/reconnection heating during the central solenoid (CS)-free plasma startup of spherical tokamak using a new 96CH 2D ion Doppler tomography diagnostics. In the last decade, magnetic reconnection research made a major progress such as (a) achievement of $\sim$1keV plasma heating in MAST both for ions and electrons, (b) demonstration of $B_{rec}^2$ scaling of ion heating ranging 0.01keV < $T_i$< 1.2keV with 0.01T< $B_{rec}$ < 0.15T in many plasma merging experiments based on outflow heating mechanism and (c) elucidation of fundamental heating characteristics: localized electron heating around $X$-point mostly by current sheet dissipation and global ion heating downstream where kinetic energy of outflow jet dissipates. Namely in the last three years, it was found that reconnection heating forms fine structure under high guide field condition of $B_t$ > $3B_{rec}$. From 2017, the formation process of the fine structure has been investigated in TS-3U ($B_t\sim5B_{rec}$) with direct measurement of magnetic field profile and high-resolution 2D imaging measurement of ion temperature profile using a new 96CH ion Doppler Tomography. As a new finding, it was found that ion temperature increases inside the current sheet as well as downstream. The high temperature region around the $X$-point is affected by Hall current $j_{Hall}$ from the decoupling of ions and electrons, the characteristic heating profile rotates poloidally toward $j_{Hall}\times B_t$ direction. This characteristic is clearer in high field side ($B_t$ depends on major radius in tokamak configuration) and with higher mass ratio (enhancement of $j_{Hall}\times B_t$ due to the larger scale length than current sheet width). While at the end of merging, ion heating downstream is surrounded by closed flux surface formed by reconnected field lines and forms another fine structure. The high temperature profile downstream propagates vertically and finally forms poloidally double-ring-like structure under the influence of better toroidal confinement with higher guide field which strongly suppresses perpendicular heat transport ($\chi^\parallel/\chi^\perp\sim$ 2($\omega_{ci}\tau_{ii})^2$>>10). This work was supported by JSPS KAKENHI Grant Numbers 15H05750 and 17H04863, and NIFS Collaboration Research Program NIFS16KLER048.

Speaker: Dr Hiroshi Tanabe (University of Tokyo)

htanabe_EX_P3_22_slide.pdf

267 Investigation of magnetic topology on spontaneous transition phenomena for high beta plasma of Large Helical Device

A topological change of the magnetic field structure on a transition phenomenon is investigated in the Large Helical Device (LHD). In the high-beta plasma experiment of the LHD, the spontaneous transition phenomenon is sometimes observed [1]. After the transition, the plasma density is increased and then the plasma stored energy is increased. One important observation after the transition is the increasing plasma volume. This indicates following points: (i) the magnetic field structure in the plasma edge is changed by a plasma response of the beta-sequences, (ii) the effective plasma volume is expanded by the change of the magnetic field, (iii) the plasma stored energy is increased due to the expansion of the plasma volume. To understand how the magnetic field changes due to the plasma response of the beta-sequences, the 3D equilibrium is studied for the transition. For a magnetic configuration with the spontaneous transition, the magnetic field is topologically changed by the plasma response of the beta sequences. The vacuum magnetic island on edge rational surfaces shrinks and the stochastic magnetic field of the long connection length expands. Therefore, the effective plasma confinement region expands due to the topological change of the magnetic field. To the improvement of the plasma stored energy on the spontaneous transition, the topological change of the magnetic field is a key factor.

Speaker: Dr Yasuhiro Suzuki (National Institute for Fusion Science)

EXP3-14.pptx

268 Ion Irradiation Induced Modifications in Tungsten Foils

The ion-solid interaction has fundamental importance and is a subject of evolving understanding for years. Energetic ions of energies eV to MeV are responsible for the kinetics in solids by transferring energy via elastic or inelastic interaction depending on the nature of the material. Tungsten is prime material to be used in future fusion devices because of its thermal and mechanical properties. In lieu of neutron irradiation, ion irradiation of tungsten is an active area of research. To explore the surface morphological effects, energetic ions of various masses were bombarded on polycrystalline tungsten. Polycrystalline tungsten foils were procured from Princeton Scientific Corporation, USA as a starting material for our study. Tungsten foils of 0.1 mm thickness were mechanically polished and annealed at two different temperature (1373 and 1838 K) for minimizing the pre-existing defects. These foils were further irradiated with Au ions of energy 80 MeV. Further sequential irradiation with helium/Deuterium ions of energy 250/100 keV were done on same set of Au irradiated tungsten foils. Pre and post irradiation surface morphological studies were done with high resolution scanning electron microscope (FESEM). FESEM studies revealed the bubble formation and other surface morphological changes of tungsten foils due to gaseous ion irradiation. In D irradiated tungsten bubble formation is more at grain boundaries and in case of sequential irradiation with He pre irradiated with heavy ions, it is noticed that bubbles were seen at the foil surface.Statistical analysis is continuing and results will be presented during the meeting. Ion-irradiation in tungsten induces different and distinguishable modifications within bulk and on the surface. Four probe DC resistivity measurements were performed in a temperature range of 10 K to 300 K to study the overall defects in tungsten foils before and after irradiation. The correlation between Residual Resistivity Ratio (RRR) and the defects in the samples will be presented.

Speaker: Dr Asha Attri (ITER-India, IPR)

summary.pdf

269 Isotope effects on confinement and turbulence in ECRH plasma of LHD

The positive isotope effects have been found in ECRH plasma of LHD. The enhancement factor of global energy confinement time (tauE) to ISS04 scaling in deuterium (D) plasma is about 17% better than in hydrogen (H) plasma. Ion scale density fluctuation level is higher in D plasma. Core fluctuation level in D decreases rapidly with increase of tauE.
Both tokamak scaling (ITER98y2) and helical scaling (ISS04) follow gyro-Bohm (GB) scaling with the exception of ion mass and ion charge number. While GB scaling predicts enhanced transport in D plasma, many experiments show better confinement (in tokamak) in D or comparable confinement (in medium-sized helical devices). In this paper, we report the first results of the improved confinement due to the isotope effects in ECRH plasma of LHD.
In the dataset, the injection power of 77 and 154GHz gyrotron was 0.6-3.9MW in D, 0.8-3.8MW in H, n _{e bar} was 0.6-3.7x10 ¹⁹ m ^-3 in D, 0.3-3.8x10¹⁹m^-3 in H. The one path absorption power was 92+-4% of injection power both for H and D plasma. The magnetic axis was 3.6m and Bt was 2.75T. tauE is systematically higher in D. This is more apparent in the high collisionality regime.The enhancement factors are tauE/tauE ISS04 =1.27+-0.12 in D and 1.09+-0.02 in H plasma. Thus, improvement of tauE in D to H is 17%.
For fixed injection power, T_e and T_i profiles are almost identical. However, n_e profile is more hollowed in D plasma. The higher n_e in the edge region results in the higher stored energy and better confinement.
Ion scale turbulence was measured by two-dimensional phase contrast imaging. The measured normalized wavenumber was around 0.4. Surprisingly, it is found that the fluctuation level is higher in D, while tauE is higher in D plasma. However, the fluctuation level reduces with increase of tauE. This dependence is clearer in D plasma. Recent gyrokinetic study shows stronger collisional stability of TEM in D than in H plasma. Also, hollow density gradient reduces growth rate both of TEM and ITG. The quicker reduction of fluctuation level the core of D qualitatively agrees with collisional dependence of TEM and more hollowed density profiles in D.

Speaker: Dr Kenji Tanaka (National Institute for Fusion Science)

ktanaka_FEC2018proc_v2.pdf

ktanaka_summary_FEC2018.pdf

270 Modification in LHCD DAC System to Incorporate Measurement of RF Power

The Lower Hybrid Current Drive (LHCD) system has four klystrons, each rated for 0.5 MW, CW power at 3.7 GHz, which are employed to launch the lower hybrid waves into plasma [1]. VME and PXI based Data Acquisition and Control (DAC) system has already been implemented for the operation of LHCD System. VME based DAC system has been modified to incorporate measurement of RF Power signals. The existing VME based DAC system has various instrumentation like DIO, AO, AI and timer cards integrated with VME RTOS program. The VGD4 acquisition card was integrated for the measurement of power from 96 signals of LHCD system. However because of random data acquisition problem, this card is replaced by IP330 analog input cards. IP330 analog cards have been included and integrated with existing system to measure 128 power measurement signals requirement with the subsystem. Carrier boards have been replaced with new version of device driver to integrate IP modules of AI, AO and timer card. Existing device driver program have been modified to add additional functionality for data acquisition and time synchronization. Adapter classes have been developed to integrate with RTOS application environment for low context switching and higher performance. NTFS has been used to handle long chunk of data during experimental shots. User interface is modified on Linux host machine to monitor and acquire for additional signals. The system has been validated during the SST-1 campaigns. Developed DAC software is modular, hierarchical and scalable in nature. To achieve the data storage with calibration and plotting, MDSPlus has been integrated for data visualization and management of after shot analysis. In this paper, the design, implementation and results obtained with IP330 cards are reported and discussed.

Speaker: Mr Rameshkumar Joshi (Institute for Plasma Research, India)

Ramesh_FEC2018_Summary_slide.pptx

271 Multiphysics approach to plasma neutron source modelling at the tokamak JET

The work presented in the paper is focused on the development of a multiphysics methodology for the creation of a realistic plasma neutron source for Monte Carlo neutron transport calculations. We begin with a description of the plasma neutron sources used in fusion neutronics so far – these are based on the assumption that the plasma is in thermal equilibrium, the neutrons being emitted isotropically and their spectrum approximated with a Maxwellian distribution. The plasma shape and neutron emissivity profiles are analysed, exhibiting major discrepancies from the current JET ITER-like wall plasma state. The analysis serves as motivation for the development of a more adequate description of JET plasma neutron emission. The methodology is based on the use of the state-of-the-art plasma transport code TRANSP and the neutron spectrum computation code DRESS. The diagnostic data of a baseline DD discharge of the JET tokamak is used as input for the TRANSP/NUBEAM ion orbit code, which evaluates the beam-target fusion reactions that govern neutron production. These simulations are the basis for the evaluation of the neutron spectra, which are performed with the DRESS code. In the next step the generation of a Monte Carlo neutron source description is discussed – the data on plasma state relevant to neutron emission is processed, meaning that the probability density functions for specific quantities are computed. The script assigned for the pre-processing is designed to serve as a tool for the analysis of neutron emission, outputting both the measured and simulated neutron rates, offering insight not only into the essentials for neutronics but also discharge specific plasma physics. A subroutine based on the source code characteristics of the advanced Monte Carlo neutron transport code MCNP is described. Within the routine the prepared plasma data is used to obtain fundamental source neutron information, i.e. location of birth, angle of emission and energy. The performance of the subroutine is analyzed and found to be comparable to MCNP generic and much simpler source descriptions. The paper is concluded with a comparison of the response of several neutron detector systems at JET (KN1, KN2) as calculated with the MCNP Monte Carlo neutron transport code, using the generic and newly developed neutron source generators.

Speaker: Mr Žiga Štancar (Jožef Stefan Institute)

Summary_Slide_Neutron-Source_Stancar_FEC2018_v1.pdf

272 Multiple turbulent plasma states in the H-mode transition on JT-60U

Multiple turbulent plasma states in the edge transport barriers (ETBs) formation are studied on JT-60U. Following a slow transition, which causes significant reduction in the ion thermal transport in the pedestal towards the neoclassical level with a weak negative Er value, we found a clear and fast changes in the particle transport in association with the change in the Er towards a strong negative value at the later H-phase. This observation suggests the existence of multiple types of turbulent fluctuations in the H-mode plasma state, which affects the ion energy and other channels of transport differently.

Speaker: Dr Kensaku Kamiya (QST, Naka)

FEC2018_kamiya_27Oct2018_slide1.pdf

273 Neutron flux distributions in the LHD torus hall evaluated by an imaging plate technique in the first campaign of deuterium plasma experiment

In the Large Helical Device, deuterium plasma experiments began in March 2017 and completed in August 2017. In this experimental campaign, about $4×10^{18}$ neurons were generated and activated components in the torus hall. The concentration of radioactive isotopes in the components in the torus hall must be evaluated to estimate the radiation dose for workers and to plan the decommissioning of LHD. For this purpose, the global flux distributions for thermal, epi-thermal and fast neutrons in the torus hall of large fusion devices were experimentally evaluated for the first time in LHD using the activation foil method measured by the imaging plate (IP) and High-purity Germanium detector (HPGe). The thermal neutron flux distribution was concentrated within about 15 m from the center of LHD. In particular, the highest flux was observed at the west region underneath the LHD where an un-borated polyethylene blocks. The borated polyethylene blocks, which works as the decelerator of fast neutron and the absorber of thermal neutron, were placed on the floor underneath the LHD except the west region. It turned out that the thermal neutron was effectively absorbed by borated polyethylene blocks placed beneath the LHD. This should reduce the radioactivity of the floor and is beneficial to maintain good environment for radiation workers. The almost uniform distribution of fast neutron was observed just underneath the LHD. The flux of fast neutron near the LHD was about one order of magnitude higher than that of thermal neutron. The region with high fast neutron flux was narrower compared to that of thermal neutron due to the quick energy loss process of fast neutron. The neutron flux distribution measurement with rough energy discrimination based on the threshold energy of neutron activation foil allows us to estimate the spatial radiation dose rate as well as the radioactivity in components in the torus hall. Therefore, the neutron flux distribution obtained here is conducive to developing the radiation safety in the deuterium plasma experiments comprehensively and to planning the future decommissioning of the LHD.

Speaker: Dr Makoto Kobayashi (National Institute for Fusion Science)

one-page Summary.pdf

274 Neutron Irradiation Impact on ITER Grade Insulating Material

Neutron Irradiation impact on ITER grade insulating material Sejal Shah1,4a, Sunil Kumar2, Sudhirsinh Vala2,4, R. Kumar2, M. Abhangi2, S. Prasad3, M. Bandyopadhyay1,4, A. Chakraborty1 1. ITER-India, Institute for Plasma Research, Bhat, Gandhinagar- 382428, India 2. Institute for Plasma Research, Bhat, Gandhinagar-382428, India 3. FCIPT Division, Institute for Plasma Research, Bhat, Gandhinagar-382428, India 4. Homi Bhabha National Institute, Anushakti Nagar, Mumbai 400094, India a.email: sshah@iter-india.org Study is performed to assess the irradiation impact on ITER grade ceramic which is widely being used for high voltage insulation in neutral beam injectors of ITER. Production proof samples of required sizes of high purity alumina were prepared and ultrasonically cleaned and are irradiated by two neutron sources. In-situ and ex-situ characterizations were performed to study irradiation impact on material properties and to ensure its structural and electrical compatibility. Insulation Resistance was observed to improve with time from 250 G ohm to 3.3 T ohm and leakage current was in correlation with Curie-von Schveindler law. However, spontaneous reduction of IR at the time of irradiation was observed which was due to radiation induced conductivity. Further, the impact of irradiation on the structure was studied by X-ray diffraction analysis. The result reveals decrease in crystalline behavior after irradiation. Surface morphology of pristine and irradiated samples was studied by Scanning Electron Microscopy and Atomic force microscopy. SEM of low energy neutron irradiated sample showed defect cluster formation on ceramic surface which was also cross-checked by increased surface roughness post irradiation by AFM. It is observed that surface morphology is getting affected mainly due to low energy neutrons whereas electrical and structural properties getting affected by high energy neutrons. To understand material performance for similar conditions of operational reactor, the study is initiated to create neutron equivalent defects in the material using ion beams and see the changes in material properties. This study will help in defining material grade for fusion based applications. Analytical assessment of nuclear activation along with experimental outcome shall be presented.

Speaker: Dr Sejal Shah (ITER-India, Institute for Plasma Research, Bhat, Gandhinagar, India)

Summary slide.pptx

275 Neutronic analysis of IFMIF-DONES Test Cell cooling system

IFMIF-DONES (International Fusion Materials Irradiation Facility – DEMO-Oriented Neutron Source) is an accelerator based d-Li neutron source which aims at the qualification of materials at the irradiation conditions of a DEMO fusion power reactor as being developed in the frame of EUROfusion’s Power Plant and Technology (PPPT) programme. The high intense neutron radiation produced in the liquid lithium target results in a strong activation of the Test Cell (TC) with the High Flux Test Module (HFTM), housing the irradiation specimens, the TC steel liner and the water cooled concrete walls. The activation and decay heat generation of the cooling pipes need to be assessed for maintenance, decommissioning and waste management purposes and the related safety analyses. This paper presents the analyses performed within the ENS (Early Neutron Source) project of EUROfusion/PPPT for providing up-to-date estimates of the activity inventories and the decay heat generation in the DONES TC facility. To this end, a series of coupled McDeLicious transport and FISPACT inventory calculations were performed using the 2017 DONES TC model and nuclear cross-section data from the FENDL-3.1 data library. Activity inventories and decay heat data were assessed for the water pipes assumed for cooling the walls. The paper discusses the results obtained for the activity and the decay heat as a function of the decay time after radiation and also addresses the issue of the radiation dose loads which are to be expected due to the activated components/systems including the cooling water system.

Speaker: Mr Gediminas Stankunas (Lithuanian Energy Institute)

singlesummaryslide.pptx

276 Neutronics Experiment for Design Validation of Indian TBM Shield Module

The testing of the breeding blanket systems is one of the vital objectives of the ITER. It will generate the significant information for DEMO fusion reactor. ITER has assigned the three equatorial ports for testing of six blanket systems. In those six, there is a Test Blanket System (TBS) of India which is Lead Lithium Ceramic Breeder (LLCB) blanket system and it will be integrated into one-half of ITER equatorial port#2. Being a part of ITER, TBS has to follow all safety & design guidelines of ITER. In order to follow the safety guideline of radiation dose limits in ITER ports inter-spaces, a shield module, made of stainless steel and water channels, is associated with Test Blanket Module (TBM) to limit the direct radiations in port inter-space areas. The conceptual design of Indian TBM shield module has been assessed by neutronic simulation using MCNP. The shield module is having the classification of radiation protection important component due to the function of radiation exposure control which leads to ensure the design of the component. A neutronic experiment is designed and performed to validate & verify the design of shield module. The design of the experiment is made by considering the two references; one is the neutron spectra on the front surface of TBM shield under ITER environment and second is the neutron attenuation in shield module under ITER conditions. The experiment is designed considering the irradiation of mock-up under 14 MeV neutron source facility of IPR. The neutron source is having the yield of 1010 n/s. The neutron spectra of the front surface of the shield mock-up have been optimized to achieve the reference spectra of TBM shield module. The neutron spectra & flux are measured using the activation foils detectors. The C/E ratio is obtained from the comparison of measured & simulated neutronic responses. The neutronic simulation is performed using MCNP5 and FENDL 2.1 cross section data. The unfolding code SAND-II-SNL is employed to obtain the neutron spectra from activation foil measurements. This experiment will also support in preparation of neutron spectra measurement for Indian TBM system and improvement of nuclear simulations. The paper will cover the detailed neutronic design, details of irradiation, neutron spectra measurements and outcome of the experiment.

Speaker: Mr H. L. SWAMI (Institute for Plasma Research)

Summary_Slide_FIP_P3-46_HLSWAMI.pdf

277 New approach to the control of particle recycling using divertor pumping in LHD

Superior control of particle recycling and of plasma density has been established in the Large Helical Device (LHD) using greatly enhanced active pumping of the closed helical divertor (CHD). In-vessel cryo-sorption pumping systems inside the CHD in five out of ten inner toroidal divertor sections have been developed and installed step by step in LHD. The total effective pumping speed obtained was 67±5 m³/s in hydrogen, which is approximately seven times larger than previously obtained. As a result, a low recycling state was observed with the CHD pumping for the first time under the helical divertor configuration in LHD featuring excellent density control even under intense pellet fueling conditions. A global particle confinement time is used for comparison of operation with and without the CHD pumping. The global particle confinement time was evaluated from the density decay after the fueling of hydrogen pellet injection or gas puffing in NBI plasmas. A short global particle confinement time after the fueling was obtained during the CHD pumping, demonstrating the control of the particle balance with active pumping in CHD for the first time in LHD.

Speaker: Dr Gen Motojima (National Institute for Fusion Science)

summary_P3-27.pdf

278 New Fusion Facilities at UKAEA – FTF and H3AT

The UK Government has invested ~€100M to create two new UKAEA centres for fusion research –
Hydrogen-3 Advanced Technology (H3AT) and the Fusion Technology Facilities (FTF) both opening in
2020-21. FTF and H3AT will foster close cooperation with industry, academia and other international
laboratories to develop and transfer knowledge between partners, offering opportunities to
undertake R&D; to reduce risk for ITER and to make significant contributions to the EU DEMO and
international fusion programmes.
The FTF offers a complete development life cycle for materials and components in three facilities.
The Materials Technology Laboratory develops and qualifies materials using small sample testing
techniques to reduce costs and offer in-service testing. The Joining and Advanced Manufacturing
Laboratory specialises in material joining and manufacturing technologies for fusion including
additive manufacture and laser welding. It has a dedicated small sample test facility, HIVE, capable
of providing up to 20MWm-2 over 20x20mm. The Module Test Facility provides fusion relevant
testing environments, with heat flux up to 2MWm-2 (and higher localised flux) and DEMO relevant
water cooling loop for metre-scale components.
H3ATprovides space for active and inactive experiments with Tritium grade ventilation and glove
boxes complete with pressure control and purging systems offer user-ready specialist facilities for a
range of R&D; activities. In addition to providing a supply of Tritium, H3AT offers a flexible gas mixing
capability, removing the need for gas mixture preparation for experiments. A flexible gas analytical
system is networked to the experimental stations that are also served with vacuum systems, Tritium
recovery and de-tritiation facilities.
This paper will describe the new facilities in terms of their technical capabilities and the progress to
their realisation.

Speaker: Mr Colin Walters

279 Novel Approach of Pulsed-Glow Discharge Wall Conditioning in ADITYA Upgrade Tokamak

In ADITYA Upgrade, glow discharge wall conditioning (GDC) is performed for long hours after the tokamak plasma operation using H gas to control Oxygen and Carbon containing impurities. This leads to high retention of H gas on Graphite limiter and Stainless Steel (SS) vessel. Subsequently, high H outgassing rate requires increased pumping time and high H recycling during plasma discharges affect the plasma performance in respect to H fueling control of the plasma. Intermittent He GDC for shorter duration can be used to decrease the H retention mainly in graphite. However, the removal of Helium from the limiter and wall is more difficult than H due to its properties of non-reactive, hard-to-trap, vacuum pumping limitation etc. A new approach involving Pulsed Glow Discharge Wall Conditioning (P-GDC) has been introduced in Aditya-U tokamak to reduce the residual H concentration in SS vessel and graphite limiters. It has been observed earlier with continuous GDC that the impurity removal rate is usually high in initial few seconds of GDC operation. The initial high reaction rate is due to the reaction of working gas ions with loosely bound outer most monolayers species. The removal rate then decreases exponentially as hard bonded O and C containing impurities come out slowly. Moreover, the released impurity gases are re-implanted in the wall materials partially deeper in presence of continuous GDC that they have been in its absence. Thus overall impurity removal rate decreases exponentially with time in presence of continuous gas GDC. Initiation of the glow discharge needs filling of H gas at high pressure ~ 10-2 mbar and ~1 kV voltage in Aditya Upgrade. In case of pulsed GDC the gas needs to be injected in pulsed mode and the discharge needs to be initiated during every gas. Therefore in P-GDC, to facilitate the fast initiation of discharge, a source of free of electrons has been introduced in the vessel. A fast feedback pulsed gas-fueling control system and electrons emission system has been developed to initiate glow discharge in each gas-feed pulse at various operating pressure 1 x 10-4 mbar and above. The different P-GDC experiments have been carried out with H, He, Ar as working gases and the results are compared with traditional continuous GDC. The design, development, operation and results of Pulsed GDC has been described in this paper in details.

Speaker: Mr Kumarpalsinh Jadeja (Institute for plasma Research)

Summary Slide Summary Slide_FIP-P3-64_K.A. Jadeja.pdf

280 Novel Method for Determination of Tritium Depth Profiles in Metallic Samples

Novel method for determining the depth profile of tritium in metallic samples has been demonstrated. Tritium accumulation in the fusion reactor materials is considered as a radiological issue due to its radioactivity. Therefore, tritium behavior prediction and estimation of its overall retention in fusion devices is of high importance. Proposed method in this study allows to measure depth profile of tritium in the metallic samples after exposure to tritium containing plasma, tritium gas or after irradiation with neutrons resulting in the tritium formation. In the method, successive layers of metal are removed using appropriate etching agent in the controlled regime and amount of evolved gases measured by the means of chromatography (gas composition and release rate) and proportional gas flow detector (tritium). Results on tritium profile in neutron irradiated, plasma exposed and tritium gas loaded beryllium have already been reported. Possible applications of the method for other metallic samples have been tested within this research.

Speaker: Dr Elina Pajuste (University of Latvia)

Summary slide Pajuste.pptx

281 Overview of the Methods developed for Fission Plants Safety relevant to the Safety of Fusion Facilities

Safety studies for fusion facilities are commonly conducted using codes originally developed for fission reactor accident analysis and adapted to model the fusion-relevant phenomena. Nevertheless there are many “fission developed” methods still not considered in fusion safety assessment which could offer significant advantages in the fusion power commercialization. Along with solving the safety and licensing critical for the fusion power commercialization will be as well the ability to reduce the cost and increase the efficiency of the power production. Among other means these were achieved in the fission power by limiting or even avoiding the conservatism in safety assessment, by improving the methods and use of the state-of-the art tools. There are many reasons for looking into the fission like similar nuclear regulatory environment, the very same nuclear safety principles and regulatory limits apply, use of mature and proven methods already accepted by the regulators, etc. The paper will address the following topics • Experimental programs, Test Matrixes and Data bases • Computer codes development, verification and validation • Computer codes assessments • Conservative or Best Estimate (BE) methodology • Uncertainty estimation methods • Phenomena Identification and Ranking Tables (PIRT) The parallel between the fission and fusion safety approaches and accident analyses methodologies will be drawn. For each of the above topics a brief presentation of the fission historical development followed by an overview of published adaptations of methods and their applications to fusion safety will be reported. The presentation will draw in particular on availability of qualified tools for accidents analyses, use of PIRT, the verification and validation of computer codes by means of separate and integral effect tests and establishing benchmark problems as well on code assessment and development of multi-physics, multi-fluids integrated code systems. These efforts should be aimed at developing a systematic safety demonstration defined by an integrated fusion safety assessment methodology.

Speaker: Dr Dobromir Panayotov (FUSION FOR ENERGY)

282 Overview of the NSTX-U Recovery Project Physics and Engineering Design

The NSTX-U device began operation in 2016, producing 10 weeks of commissioning and scientific operations. However, a number of technical issues, including the failure of a key diverter coil, resulted in the suspension of operations. A comprehensive extent of condition review was initiated at the request of the Department of Energy; this paper will summarize the result of that process, focusing on the design and implementation improvements that are in progress in order to resume operation and increase reliability. Many elements of the physics design have been revisited as part of the Recovery, although most key NSTX-U mission goals remain. New requirements for the divetor heat fluxes have been defined, based on recent SOL heat flux width models. New halo currents loads have been determined based on combining data from NSTX, NSTX-U, MAST, and conventional aspect ratio devices. New error field analysis has been conducted, with the goal of optimizing both the global MHD stability and minimizing PFC heat flux asymmetries for scenarios with large poloidal flux expansion. New divertor coil current requirements have been defined, based on the tolerable heat fluxes and current drive for the various potential equilibria. Numerous design improvements are being included as part of the Recovery effort, with a primary goal of supporting flexible operations at BT=1 T, IP=2 MA, Pinj=10 MW, and tpulse=5 seconds. New designs of graphite plasma facing components utilize castellations to reduce the mechanical stresses, allowing tiles to reach surface temperature limits, ~1600 degC, driven by sublimation. Improved divertor coil designs simplify fabrication and facilitate turn-to-turn testing. Modifications to the NSTX-U vacuum chamber will eliminate one the ceramic insulators necessary for coaxial helicity injection (CHI), increasing system reliability at the expense of the CHI research capability. The physics and engineering R&D activities that support Recovery will be summarized, along with highlights of the new design. This work was supported by U.S. DOE Contract D-AC02-09CH11466 and DE-AC05-00OR22725

Speaker: Dr Stefan Gerhardt (Princeton Plasma Physics Laboratory)

283 Particle balance investigation with the combination of rate equations of hydrogen state and hydrogen barrier model in long duration discharges on all-metal PFW QUEST

Out-flux of fuel particles from plasma-facing walls (PFWs) during long duration discharges on all-metal PFW QUEST is in agreement with a prediction of the hydrogen (H) barrier model we proposed [1]. A simple calculation based on the combination of rate equations of H state and the H barrier model predicts a significant impact in the response of plasma density. This result indicates that a proper wall model including the effect of deposition layer that creates H barrier should be developed even in all-metal PFW devices.

Speaker: Prof. Kazuaki Hanada (Advanced Fusion Research Center, Research Institute for Applied Mechanics, Kyushu University)

EX_P3-12.pptx

IAEA2018 paper_20180927.pdf

284 Pellet fuelling prospects and injector system for Aditya-U tokomak

High density plasma operation with centrally peaked profile is one of the key aspects in achieving break-even condition in magnetically confined fusion devices. In this prospect an efficient fuelling method capable of supplying particles into the core of the plasma is desired. Till date, cryogenically solidified pellets of hydrogen isotopes have been proved as an efficient method of replenishing the spent fuel in fusion devices. Apart from fuelling, pellet injection is also useful for plasma confinement improvement, ELM (edge localized mode) pacing, plasma disruption mitigation (which can damage the tokomak first wall) using shattered pellets are other important application. The use of pellet injection technique is actively considered for ITER plasma and for future DEMO relevant studies. Institute for Plasma Research (IPR), India has initiated development of Pellet Injection System. A study related to pellet injection in ADITYA-U is planned and desired pellet parameter is estimated by applying standard theoretical models such as neutral gas shielding models (NGS). While designing the pellet injection system, the targeted plasma electron temperature considered is few hundreds eV to 2 KeV. For ADITYA the pellet size and speed are decided to be ~1.5 mm and < 800 m/s, respectively. Considering estimated design parameters a single barrel hydrogen pellet injection system is developed for pellet injection related studies. The injector is based on pipe gun concept, where, a pellet formed in situ in the gun barrel is accelerated to high speed using high pressure light propellant gas. This system uses a cryogen free, closed loop compact cryocooler, which provides operational reliability to the pellet freezing process. Pellet formation study is successfully demonstrated using the designed injector. In test bench setup pellet size of < 1.8 mm and velocity of < 900 m/s has been demonstrated. A programmable logic controller based control system is integrated to the tokomak to operate the injector remotely during plasma operation. The pellet parameters are characterized using standard diagnostic such as fast imaging camera and light gate system. This injector will be employed for experiment in Aditya-U tokomak. The design of the pellet injector and its future prospect for application in Aditya-U tokomak will be presented.

Speaker: Dr Jyoti Shankar Mishra (Institue for plasma research)

iaea2018-FIP_P3-51-slide summary.pdf

285 Performance of 14-MeV Neutron Generator at IPR

The Fusion Neutronics laboratory at Institute for Plasma Research (IPR), Gandhinagar, India has indigenously developed an accelerator based 14-MeV neutron generator for fusion neutronics studies for material development under Indian Fusion program. This neutron generator is producing neutron yield of $10^{10}$ n/s and it will be further upgraded to the $10^{12}$ n/s. It consists of a 2.45 GHz ECR ion source, 300 kV linear accelerator, beam diagnostic system, TMP based vacuum system, solid tritium target and a control system. Various neutron detection techniques like foil activation, associated alpha particle detector, and He-3 proportional counter have been set up to in the system measure the neutron yield independently and online neutron yield. Results of all independent diagnostic were compared. Monte Carlo technique was used to get reaction rate for foil activation. This paper describes the experimental setup and performance of the 14-MeV neutron generator including its neutron diagnostic to highlights its stability for continuous operation.

Speaker: Mr SUDHIRSINH VALA (INSTIUTE FOR PLASMA RESEARCH)

SJVala_FEC-preprints.pdf

SJVALA_FEC Summary.pdf

286 Performance of Transmission Line System at 42±0.2GHz for an Indigenous Gyrotron System

In high microwave power applications like gyrotron, transmission line system, calorimetric dummy load, etc, requires design, modeling, simulation and evaluation of transmission line system before fabrication of the same is undertaken. Under the aegis of Department of Science and Technology (DST), a multi-institutional program for the development of a gyrotron operating at 42±0.2GHz/200kW/3secs in TE03 mode has been undertaken. It is currently in an advance stage of test and commissioning at IPR (Institute for Plasma Research). It is desired for plasma applications that the output mode of gyrotron in TE03 mode is to be converted to HE11 mode for efficient coupling to plasma. The HE11 mode (TEM00 mode), has an electric field distribution very close to that of an ideal Gaussian mode. This gaussian like mode is preferred for high-power transmission through overmoded corrugated waveguides, which gives insertion loss lower than that of any other modes. The proposed design of transmission line system converts unpolarized TE03 mode into polarized HE11 mode.
The ripples walled mode converters are designed for converting TE03 to TE01 in two steps. TE01 mode is converted to TM11 by bending a smooth waveguide at an angle of 34.94°. Finally TM11 mode is converted to HE11 mode. Miter bend for TE01 mode and HE11 mode are also designed. The designed corrugated waveguide operates at 42±0.2GHz. The Final design of all the components are verified using simulation studies carried out in CST-MWS. Performance optimization has been carried out prior to fabrication process. At this point in time, fabrication of many of the mode converters has been completed and miter bends are under mechanical fabrication process. As a part of a design, transmission line system is mechanically compatible to high vacuum and 1bar pressurization.
The system includes two design approaches whose performances are compared in terms of insertion loss, bandwidth and cost effective manufacturing. Both the proposed design approaches of transmission line system have total insertion loss of 1.3 to 1.5dB. The bandwidth of first design approach is wider as compared to second. Flexibility of manufacturing process of transmission line system is an advantage of second approach. The Salient point of design and simulation studies of transmission line system are discussed and highlighted in the manuscript.

Speaker: Ms Pujita Bhatt (Senior Research Fellow)

IAEA-FIP-P3-52.pptx

287 Plasma current generation and ramp-up by the lower hybrid wave using outboard-launch and top-launch antennas on the TST-2 spherical tokamak

Plasma current start-up without a large flux swing by the central solenoid is a critical issue in fusion research. The lower hybrid wave (LHW) is known to be an effective current drive tool in conventional tokamaks, and it is used in the TST-2 spherical tokamak (ST) device. The TST-2 device provides a unique opportunity to compare outboard-launch and top-launch schemes for plasma current generation and ramp-up by LHW. The Top-launch scheme is expected to have good core accessibility and thus expected to be superior than the outboard-launch scheme. However, one of operational difficulties for the top-launch scheme is the initial vertical position control. The recent operational optimization enabled achievement of the maximum plasma current of 27 kA, which is higher than that obtained by the outboard-launch scheme. By flipping the polarity of the toroidal field, we can realize a scheme equivalent to the bottom-launch scheme. We found that the achieved plasma currents are similar to those with the normal toroidal field direction. This fact indicates that the losses associated with wave reflections at the boundaries are not significant in these cases. The plasma current increases with the toroidal field strength, and this dependence is quite reasonable when we consider wave accessibility of LHW. If we want to increase the toroidal field strength further, one difficulty we will face is pre-ionization. Normally we use ECH (2.45 GHz/ 5 kW) for pre-ionization, with the fundamental resonance located around the major radius of the top-launch antenna. We will need another pre-ionization tool for higher field experiments. The AC Ohmic operation is one such tool, which requires only about two orders of magnitude smaller flux swing than that for a typical Ohmic discharge. The growth rate of pre-ionization by AC Ohmic operation is rather insensitive to the toroidal field strength. We confirmed that the operation is useful not only for the outboard-launch scheme but also for the top-launch scheme. This fact implies that we obtained a reliable pre-ionization tool which is insensitive to the magnetic field strength.

Speaker: Dr Akira Ejiri (Graduate School of Frontier Sciences, The University of Tokyo)

FEC2018summary_ejiriV0.pdf

288 Radiation Properties of the Metal Structural Materials during Low-Temperature Damaging Irradiation

The structure and physical-mechanical properties of the metal structural materials (SM) with BCC (ferrite-martensitic steels, alloys of vanadium, etc.) and FCC (austenitic steels, etc.) crystal lattices in the conditions of “before-after-during” low-temperature irradiation were analyzed. The qualitative and quantitative distinctions of the states and properties of SM “before-after” (an equilibrium state) and “during” (essentially non-equilibrium state) irradiation occur. Depending on the rigidity of the stress-deformed state, type of a crystal lattice, the low-temperature yield strength and mobility of dislocations there can be different modes of the plastic deformations with the brittle fracture by rupture or shear (cold brittleness).The conditions for occurrence of the cold brittleness are the formation of the critical cracks of rupture and shear, generating dislocations, high low-temperature yield strength, high starting stress for movement of dislocations and low level of viscous braking of the dislocations in the dynamic area of their mobility on the fronts of a cracks of rupture and shear. The speeds of propagation of a critical crack and deformation shear strip are determined by the dynamic mobility of the dislocations on their fronts. The conditions for occurrence of the cold brittleness can be implemented in BCC SM, defining their temperature ranges of the cold brittleness, and are not implemented in FCC SM (the cold brittleness is absent). “Before-after” irradiation in BCC SM the cold brittleness manifests itself by the modes of the plastic deformation with a brittle fracture during an avalanche propagation of a critical crack (rupture cold brittleness) or with a brittle shear during formation and avalanche propagation of the deformation shear strips (shear cold brittleness). “During” low-temperature irradiation in BCC SM the state of irradiation cold brittleness with a brittle fracture by rupture or shear is not formed (absent). Possibilities and difficulties are discussed for development of the physical models and computer simulation of the radiation structures, defects and physical-mechanical properties of SM.

Speaker: Prof. Viacheslav Chernov (A.A.Bochvar High-technology Research Institute of Inorganic Materials (SC "VNIINM"))

FIP-P3-41-SUMMARY-CHERNOV-FEC-2018.pdf

289 Rapid Radial Propagation of Momentum Change and Flow Oscillation Associated with a Pellet Injection

We report the discovery of rapid momentum change and oscillatory flow as a result of the pellet injection. Novel diagnostics tools with high spatio-temporal resolution applied to the perpendicular flow velocity and turbulence intensity measurements in LHD experiments show the following results. Just after the pellet injection, (1)the damped oscillating flow velocity and the increasing density fluctuation are observed in a few milliseconds. (2)The propagating flow structure towards the core direction is observed, and its speed is faster than the pellet penetration speed. These results are quite meaningful for understanding the physics of pellet penetration in toroidal plasma. Just after the pellet injection, the perpendicular flow velocity is oscillating and damping in a few milliseconds. The damped oscillation model can be applied to fit the observation data. The toroidal mode number of this oscillation is estimated to be 0 or 10. We can also measure the turbulence intensity at the same position. The turbulence increases rapidly and then decreases before the end of the damping of the oscillatory flow. The generation and damping of flow itself might be caused by the turbulence. On the other hand, the electron density increases and the electron temperature decreases with finite delay. Therefore, it is found that the change of local density gradient seems likely not to play an important role for the start of this oscillation. The ballistic propagation of the change of flow structure towards the core direction is observed in the region at r/a<0.97, where the mono-cycle temporal oscillation is observed. In order to measure such a fine velocity profile, a high sampling rate digital storage of 80 GS/s is applied for the frequency comb microwave Doppler reflectometer. The propagation speed increases at the location of r/a~0.97 and exceeds 1.5km/s, which is three times faster than the pellet penetration speed. This indicates that the rapid propagation of information of momentum change is present. Currently, it is also found that the location of the pivot point is not at the rational surface, and the information of momentum change propagates at least r/a~0.86 before the start of the electron density rise. Therefore, it is found that the momentum changes rapidly, and this may lead the global change of the radial electric field and affect the bulk plasma transport.

Speaker: Dr Tokihiko Tokuzawa (National Institute for Fusion Science)

1page_summary_TT.pdf

290 Real-Time Feedback Control System for Plasma Position Stabilisation in ADITYA-U Tokamak

The ADITYA-U tokamak (R0 = 0.75 m, a = 0.25 m) is designed to have shaped plasmas in both single and double null diverter configurations. It is quite well known that sustaining a shaped plasma in tokamak requires very good plasma column position control, both horizontal and vertical. A proportional–integral–derivative (PID) based control system has been designed and operated to achieve horizontal and vertical plasma positions control in ADITYA-U tokamak. In this control system, the transfer function model [1] of control power supply and different position diagnostics has been incorporated such that whole system fulfils the stability criteria of the whole control system. In order to incorporate effect of change in radius of plasma column and the vessel eddy current on the position measurements, new adaptive techniques [2] are incorporated to achieve plasma position regulation with minimum error. Detailed comparisons have been carried out between the results obtained with the conventional PID approach and adaptive method approach. Furthermore, the system has been trained to take appropriate actions during the disruption or plasma failure in the tokamak. The complete system has been rigorously tested with sample signals before implementing to the ADITYA-U plasma discharges. The control system is integrated to the composite plasma control system of ADITYA –U. The complete design, installation, operation, training of the system along with all the relevant testing will be presented in the paper.

Speaker: Mr ROHIT KUMAR (Institute For Plasma Research)

FEC_SUMMARY.pdf

FEC_SUMMARY.pptx

291 Recent progresses on the RMP researches towards active control of tearing mode in the J-TEXT tokamak

Controlling the tearing mode (TM) is one of the major topics of fusion research, since TM degrades the plasma confinement and even induces major disruption if it is locked. Previous experimental and theoretical studies showed that the resonant magnetic perturbations (RMPs) influence both the rotation and width of the TM. As a result, the static RMP could apply a net stabilizing and braking effect on a rotating TM, and hence suppress or lock the TM. Based on these effects, 3 strategies for controlling the TM have been proposed and tested in J-TEXT by applying the pulsed or fast rotating RMPs. This paper will present these recent efforts.

On J-TEXT, the RMP system is capable of providing either a static or a high frequency (up to 6 kHz) rotating RMP field, with dominant 2/1 component. To study the proposed TM control methods, extensive upgrades of the power supply (PS) system for RMP coils were carried out, such as building a pulsed DC PS which could follow the TM frequency with 50% duty cycle, a hopping frequency AC PS, an on-line system for measuring the TM phase and frequency.

The first control strategy is to apply pulsed RMP to the TM only during the accelerating phase region. By nonlinear numerical modelling, it is proved efficient in accelerating the mode rotation and even completely suppresses the mode. The followed experimental attempt with the pulsed RMP at relative low amplitude has demonstrated the acceleration effect. The second control method is to apply a RMP, rotating with varying frequency which is kept slightly higher than that of a TM. Currently, the open loop application of this hopping PS led to the locking of TM at 4, 5 and 6 kHz successively. Further investigation with feedback controlled hopping PS is needed to validate this method.

Thirdly, the fast rotating RMP field has been successfully applied for the avoidance of mode locking and the prevention of plasma disruption. A set of disruptive discharges induced by intrinsic mode locking were performed by reducing the edge safety factor from 3 towards 2. The braking of TM usually lasted for ~20 ms and the disruption followed at ~10 ms after the mode locked. Trigged by the mode locking warning system, the 3 kHz rotating RMP was applied before the mode locked. The TM was accelerated to 3 kHz and the intrinsic mode locking was avoided. As a result, the disruption was prevented.

Speaker: Prof. Yonghua Ding (International Joint Research Laboratory of Magnetic Confinement Fusion and Plasma Physics (IFPP), AEET, SEEE, CnHUST)

Summary Slides 0f EXP0_13.pptx

292 RGA Analysis and Surface Analysis of SST-1 Graphite Tiles in High Temperature Vacuum Baking

Steady state Superconducting Tokamak (SST-1) is a large aspect ratio Tokamak with a major radius of 1.1 m and minor radius of 0.20 m. Plasma Facing Components (PFC) is one of the major sub-systems of SST-1 Tokamak. Plasma Facing Components of SST-1 consists of divertors, passive stabilizers, baffles and poloidal limiters. PFCs are designed and fabricated to be Ultra High Vacuum (UHV) compatible and high temperature compatible for steady state plasma operation. All PFCs are made up of graphite tiles mechanically attached to the copper alloy substrate. Graphite is chosen as a first wall armour material in SST-1 Tokamak because of its high thermal shock resistance and low atomic number of carbon. Graphite, because of its porous nature absorbs water vapour and other gasses from atmosphere. Generally graphite tiles are given a high temperature bake-out treatment prior to installation inside the tokamak to reduce the in-situ wall conditioning period. There are about 3800 numbers of graphite tiles of different sizes to be fitted on 132 numbers of PFC copper modules. All the 3800 graphite tiles were given a high temperature bake-out at 1000 oC to remove the entrapped gasses, under high vacuum in a vacuum furnace before installation into the SST-1 vacuum vessel. Residual Gas Analyser (RGA) was used to measure the outgassing at various temperatures during the entire vacuum baking process. RGA works on the principle of Quadrupole Mass Spectrometer. RGA is used to detect and analyse the residual gases during vacuum pumping and high temperature baking of graphite tiles. Surface analysis of graphite tiles have been carried-out using Scanning Electron Microscope (SEM) and X-Ray Diffraction analysis (XRD) before and after baking. Elemental analysis was also carried-out before and after baking to qualify the graphite samples. This paper will discuss about the residual gas analysis and surface analysis of SST-1 graphite tiles in high temperature vacuum baking process.

Speaker: Mr ArunPrakash Arumugam (Institute for Plasma Research, Bhat, Gandhinagar, India)

FIP_P3-16_Summary_ArunPrakash.pdf

293 Safety factor profile control with reduced CS flux consumption during plasma current ramp-up phase using reinforcement learning technique

Safety factor profile control via active feedback control of electron temperature profile during a plasma current ramp-up phase of a DEMO reactor is investigated to minimize the magnetic flux consumption of a central solenoid (CS) for wide range of *q* profiles. It is shown that *q* profiles with positive, weak and reversed magnetic shear can be obtained with less than half of the empirical estimation of the resistive flux consumption ($\Psi_{\rm res}$). For the optimization of time dependent feedback gain, we introduced a reinforcement learning technique. This enables to follow a rapid change in the target profile of the electron temperature by changing the feedback gain adaptively. With this adaptive feature of the reinforcement learning, we also confirmed that $T_{\rm e}$ profile can be controlled in the plasma simulation with various thermal transport property by one control system.

Speaker: Dr Takuma Wakatsuki (National Institutes for Quantum and Radiological Science and Technology)

one_page_summary_v2.pptx

294 Scaling Study of Reconnection/ Merging Heating of Spherical Tokamak Plasmas for Direct Access to Burning Plasma

The high-power reconnection heating of ST plasma has been developed in TS-3U, TS-4U and MAST experiments, leading us to direct access to burning plasma. This unique method is caused by the promising scaling of ion heating energy that increases with squire of reconnecting magnetic field B_rec. We studied mechanisms for this B_rec^2-scaling of reconnection (ion) heating mainly using TS-3U experiment and PIC simulations and found the following issues: (i) the ion heating energy is as high as ~40-50% of poloidal magnetic energy of two merging ST plasmas and (ii) is not affected by (guide) toroidal field B_t, in the region of B_t/B_rec >1 under two important conditions: (iii) compression of current sheet to order of ion gryoradius and (iv) the ST plasmas fully isolated from coils and walls. The sheet compression to ion gryoradius was found to be a key condition to realize the fast reconnection as well as the high power ion heating consistent with the B_rec^2-scaling prediction. Under this condition, the ion heating energy is determined uniquely by B_rec~B_p not by B_t in the conventional tokamak operation region: B_t/B_p>1. The merging ST plasmas need to be fully pinched off from the PF coils for the purpose of minimizing the hot ions heated by the reconnection/ merging. This promising scaling is expected to realize the burning plasma temperature T_i>10keV just by increasing B_rec over 0.6T (under the constant electron density n_e~1.5x10^19 [m^-3]), leading us to construction of new high-B_rec field merging ST devices: TS-U in U. Tokyo and ST-40 in Tokamak Energy Inc

Speaker: Prof. Yasushi Ono (University of Tokyo)

YOnoEXP3-24slide.pdf

295 Status of Studies of Pulsed Heat Load Influence on Tungsten at BETA Facility and Station of SR Scattering "Plasma" in BINP

Experiments simulating the pulsed heat loads expected in the ITER divertor were carried out at the BETA facility in the Budker Institute. Using a pulsed electron beam with a duration of 0.2-0.3 ms and heat load with a heat flux factor HFF ≈ 30 MJ m-2s-0.5 below the melting point of tungsten were obtained. A distinctive feature of BETA is the ability to study the processes of erosion of tungsten in situ during the heating and immediately after it in the cooling stage. This ability is provided by optical diagnostic methods, using the thermal radiation of the surface and illumination by a continuous laser. The obtained data make it possible to study the dynamics of the temperature distribution on the target surface and the development of its erosion in time. The image of the target surface in its own thermal radiation shows that even under a homogeneous electron beam, having a Gaussian profile with a full width at a half maximum of about 17 mm, hot spots are visible with a temperature much higher than the temperature of the surrounding area. Analysis with SEM and microsections shows that overheating is associated with a decrease in heat removal from these surface areas due to cracks caused by pulsed heating. The method of laser illumination reveals a two-stage process of erosion of the polished tungsten surface after the first heat load. Initially, the surface roughness begins to increase, reaching a maximum at the end of the heating pulse, and then decreases within a few milliseconds upon cooling to a value 2-3 times higher than the initial level of roughness. The second stage of surface modification, corresponding to surface cracking, occurs spontaneously and rapidly develops for a time of the order of ten microseconds on a sample already cooled to room temperature. The delay in the initiation of cracking of the surface exceeded the time required for the transition from the plastic to the brittle state by 3-4 orders of magnitude. Synchrotron radiation scattering station "Plasma" develops diagnostics of deformations and stresses in the material under the pulse heat load using the diffraction dynamics. This diagnostic has three principal features: measurements with time resolution, measurements inside the material and measurements with the depth resolution. Currently, the measurement of the dynamics of the shape of the diffraction peak is demonstrated.

Speaker: Dr Arakcheev Aleksey (Budker INP)

296 Structural analysis for strength and fatigue life of half coupling weldment for large cooling water pipes

ITER cooling waters system consists of large piping network to remove the heat load of about 950MWatt through various branched connections. Many of the branches are connected to main pipes by half coupling full penetration weld joints. There is requirement is to have full penetration for all the joints however quality classification (QC-2), recommends only 10% testing of the total weldment. In view of this it is expected that there can be some joints with little or no penetration.. The above requirement demands for the structural strength and fatigue life is assessment to ascertain that components is not failing even if there is no weld penetration. The design by analysis approach is considered for structural and fatigue life assessment, for maximum expected loads combination case. The weld joint is structurally qualified using ASME code. Fatigue life of weld joint is calculated using both ASME Section VIII Div.2 and RCC-MR RR3261.12. The maximum stress and fatigue life observed for full penetration is 92 MPa and 315766 cycles as per ASME and 200000 cycles as per RCC-MR. Whereas, in no penetration the stress is 188 MPa and fatigue life is 137210 cycles as per ASME and 1500 cycles as per RCC-MR. It is concluded in the paper that weld joint is safe for both the case in most severe load case combination.

References:
• P. Dong, J. K. Hong, “The Master S-N Curve Approach To Fatigue Of Piping And Vessel Welds”, Welding in the World January 2004, Volume 48, Issue 1, pp 28–36,

• ASME Sec VIII Div 2

• RCC-MR RR3261.12

• Ansys Theory of Reference

Speaker: Mr Kunal Bhatt (ITER-India, Institute for Plasma Research)

Summary slides_Structural analysis for strength and fatigue life of half couplin.pdf

297 Structural and Vibrational Properties of Lead-Lithium Alloys: A First Principles Study

Lead-Lithium (Pb-Li) alloy in its eutectic composition is one of the promising candidates to be used as liquid blanket in fusion reactor. Helium cooled Lead Lithium (EU-HCLL), Dual cooled Lead Lithium (US-HCLL), Indian LLCB are some of the concepts being explored worldwide for future fusion reactor [1]. In this scenario, the characterization of Pb-Li alloy becomes important to gainfully understand its underlying physical/structural behavior. In the present paper, we report the results of our computer experiments on structural and vibrational properties of Pb-Li. Present work is performed using plane wave pseudopotential density functional theory within generalized gradient approximation (GGA). Calculations of various structural properties at ambient condition (T, P = 0) are performed using Quantum ESPRESSO package. Further, phonon frequencies along major symmetry directions are also calculated using density functional perturbation theory. Three independent elastic constants are also calculated for both the compensating structures namely Rhombohedral and CsCl type. Calculations of equation of state at elevated temperatures suggest that Pb-Li is a soft material undergoing large volume change with pressure. Further, some thermodynamic properties at elevated temperatures are also reported.

Speaker: Dr Shyamkumar Khambholja (B & B Institute of Technology, Vallabh Vidyanagar, Gujarat, India)

One Page Summary.pdf

298 Studies on high temperature vacuum brazing of Tungsten to Tungsten alloy materials for DEMO divertor application

This work summaries the experimental studies on joining of tungsten based refractory materials at high temperature using vacuum brazing process. The objective of the joining of these refractory materials is to develop the joining technique for fabricating helium cooled divertor target relevant to DEMO fusion reactor. These so called - divertor fingers - are expected to handle the incident heat flux of 10MW/m2, to be cooled by multiple helium jet at high pressure (~ 10MPa) and high temperature (~ 600 deg C) helium gas environment. For joining of W (tungsten) to WL10 alloy (tungsten + 1% Lanthanum oxide), high temperature vacuum brazing has been performed at temperatures above 1000 deg C using selective brazing fillers using Gleeble-3800 thermo-mechanical simulator at IPR. For pre-qualification of the brazed joints, the brazed specimens are subjected to 500 nos. of thermal cycles at 950 deg C to 800 deg C using Gleeble-3800 system. The brazed joints are characterized by Non destructive testing (NDT) - Ultrasonic Testing (UT), microstructural and mechanical characterization. The experimental methodology and results of the characterization will be presented in the paper.

Speaker: Dr Premjit Singh Kongkham (Institute for Plasma Research)

Summary slide.pdf

299 Study of locking mechanism of locked-mode-like instability in helical plasmas

The frequency slowing-down mechanism of the locked-mode-like instability without a large magnetic island is investigated for the first time, based on the LHD experimental analysis. The slowing-down frequency is caused by two processes. One is the resonant surface moving to the small E × B rotation frequency region and the other is the slowing-down E × B rotation frequency around the resonant surface. Both processes are almost the same as those of the instability with a large magnetic island. The new exprerimental results presented in this synopsis suggest that the mode frequency slows down even though the precursor does not have a large magnetic island. In addition, the duration of the frequency slowing-down phase becomes longer as the external RMP amplitude becomes smaller. This is because the slowing-down rate of the E × B rotation frequency around the resonant surface after excitation of the precursor is smaller for a smaller external RMP amplitude. These results also suggest that error fields, which have the same effect as the RMP, should be reduced to obtain sufficient time for controlling the locked-mode-like instability.

Speaker: Dr Yuki Takemura (National Institute for Fusion Science)

Summary Slides FEC2018_summary_slide.pdf (Protected)

300 Study on production and extraction of negative ion impurity ions in a Cesiated negative ion source

The detection of a peak corresponding to a hydrogen bearing impurity species (mostly due to water vapour :H20) was reported many times in past while performing the Doppler shift spectroscopy (DSS) diagnostics in several neutral beam injectors based on positive ion sources. However, for the experiments based on negative ion sources, we are reporting the detection of this peak for the first time. This peak always appeared in DSS spectrum when the background pressure at the observation location is ~ 1x10-4 mbar and disappeared when the pressure at the observed location is ~1x10-5 mbar. For the present experiments, the negative ions of H2O can be formed by dissociative attachment of (H20-)* leading to the formation of H−, O− and OH− fragments. The dissociative attachment seems to be the cause of the formation of this negative ion species due to favourable conditions such as 5-10eV in driver region for vibrational excitation and 1-2eV near plasma grid. A detailed study on this peak using the DSS spectrum and the pressure traces obtained using Residual Gas Analyzer was carried out in ROBIN (RF Operated Beam source in India for Negative Ion research) test stand. Estimates of impurity content have been made using intensity ratio of fast hydrogen peak and hydrogen peak originating from the negative ion impurity. The extracted current of hydrogen neutrals originating from these impurities are estimated. To obtain this value, the Balmer-alpha excitation cross-section at low energies (~ 1.5 keV) were reviewed and few approximations were made since the published data is available only for the higher-energy ranges for such processes. These approximations are outlined in this paper. There is some evidence that the amount of impurity present in the ion source affects the ratio of the main species.

Speaker: Mrs Bharathi Magesh (Institute for plasma research)

summary_FIP_P#_47.pptx

301 Surface Characterization of Li coatings and their interaction with plasmas for fusion applications via Ion Beam Analysis Techniques

Conditioning of Plasma Facing Components (PFC) is a common practice to improve the plasma performance in both tokamaks and stellarators. The evaporation of thin Li films on the PFC and first wall has given positive results in multiple machines (CDX-U, LTX, TFTR, NSTX, EAST). Reduced recycling and impurity concentration in the plasma are commonly associated with Li. As a consequence, improved energy confinement times and increased stored energy have been observed, in addition to the reduction of Edge Localized Modes (ELMs) frequency. As a consequence, multiple studies have been dedicated to investigate the surface properties of Li and its interaction with species that are common in fusion environments e.g. H, D, O. As the Plasma Material Interactions (PMI) occur near the surface of the PFC (top 10-100 nm), methods with such probing depths, such as Ion Beam Analysis (IBA) techniques, are a remarkable resource to characterize these materials and the effect that plasmas have on them. The Dynamics of ION Implantation and Sputtering Of Surfaces (DIONISOS) is an in-situ PMI facility, designed to expose samples to plasmas and interrogate their surfaces using IBA. The experiment is equipped with a helicon plasma source that can produce discharges with fluxes near 1021m-2s-1 and electron temperatures close to 6 eV. DIONISOS is attached to an ion accelerator, allowing execution of Elastic Recoil Detection (ERD), Rutherford Backscattering Spectroscopy (RBS), and Nuclear Reactions Analysis (NRA). Recently, the facility has been equipped with a Li evaporation system for in-situ deposition of thin films on the substrates. The combination of modification and analysis tools available in DIONISOS, makes it ideal to study the dynamic and multivariable relationship of Li and plasmas. This work includes real time ERD and RBS data collected during deposition and erosion of thin Li films applied on different substrates. Various substrates have been used for characterization of the deposited films preparing to study the interaction of Li with materials relevant to fusion applications. In the same way, several experimental parameters have been optimized for better quantification of the relevant species.

Speaker: Dr Felipe Bedoya (MIT-Plasma Science &amp; Fusion Center)

IAEA18_Bedoya_Contributions.pdf

302 Synergistic Effect of Impurity and Hydrogen Gas Puffs on Plasma Detachment in the GAMMA 10/PDX Tandem Mirror

In Plasma Research Center, University of Tsukuba, divertor simulation experiments have been conducted at the end region of GAMMA 10/PDX. The high temperature end loss plasmas of GAMMA10/PDX are a functional tool for simulating edge and divertor plasmas and contribute to developing a deeper understanding of the physics involved in plasma detachment. Our aim is to study detachment phenomena under equivalent conditions for ITER SOL and divertor plasma under high temperature and strong magnetic field. So far, we have performed characterization of plasma detachment from high temperature plasma (ion temperature has achieved a few hundred eV) produced by a large tandem mirror device for various radiator gases. For ideal detached plasma operation, the amount of impurities is expected to be as low as possible. In this study, we have investigated the synergistic effect of a combination of various impurity gases and hydrogen gas on plasma detachment of high temperature plasma, equivalent to SOL plasma of tokamaks in the GAMMA 10/PDX end region, utilizing an open magnetic field configuration. A small puff of an impurity gas (N2, Ne, Ar, Kr, Xe) in combination with a puff of H2 gas is examined to evaluate their synergistic effect on the formation of detached plasma; the following results are obtained: (i) A combination of N2 and H2 puffs showed clear decrease of electron density and ion flux, (ii) N2 and H2 puffs form a strong density gradient along the axial direction and (iii) other noble impurity gases showed insufficient synergistic effect. The new results indicate the possibility of achieving a reliable divertor operation scheme and the importance of investigating molecular processes in further detail. We can contribute to the optimization of detached plasma formation through a deeper understanding of the H2 and N2 assisted recombination process.

Speaker: Dr Naomichi Ezumi (University of Tsukuba)

IAEA-FEC2018_slide_ezumi_EX_P3-9.pdf

303 The Advanced Tokamak Path to a Compact Net Electric Pilot Plant

Physics based simulations using a new integrated 1.5D core-edge approach for a whole device modeling capability project a compact net electric fusion pilot plant is possible at modest scale based on the advanced tokamak concept, and identify the key parameters for its optimization. These first of a kind reactor simulations provide new insights cf. previous “systems code” projections by self-consistently applying transport, pedestal and current drive physics models to converge fully non-inductive stationary solutions without any significant free parameters. The approach provides new insights into reactor optimization with increasing plasma density, pressure and toroidal field found to lower auxiliary heating and current drive demands, and thus required fusion performance and recirculating power. Solutions at the ~4m major radius scale are identified with margins and trade-offs possible in achievable parameters. Remaining current drive is projected from neutral beam and helicon ultra-high harmonic fast wave, though other advanced current drive approaches presently being developed may also be useful. The resulting low recirculating power and double null configuration leads to a divertor heat flux challenge that is comparable to ITER Neutron wall loadings also appear tolerable. Strong H-mode access (factor >2 margin over transition scaling) is maintained with ~30-60% core radiation. The approach would benefit from high temperature demountable superconductors to provide performance margin at elevated field, and to aid in a nuclear testing mission. However, solutions are possible with conventional superconductors. An advanced load sharing and reactive bucking approach in the main field and solenoid coils has been developed and would facilitate handling of mechanical stresses. Nevertheless, the prospect of an affordable test device which could close the loop on net-electricity production is compelling, motivating research to prove the techniques projected here. Work supported by the US DOE under DE-AC05-00OR22725 and DE-FC02-04ER54698.

Speaker: Dr Jin Myung Park (Oak Ridge National Laboratory)

Buttery 2018 IAEA FIP 1 pager single resave.ppt

304 The Configuration Dependence of Isotope Effects on Turbulence System in Heliotron J

The hydrogen/deuterium (H/D) isotope effects on fluctuations and its configuration dependence are studied in a helical device, Heliotron J. The isotope dependence of a toroidally symmetric fluctuation in low frequency range of <~4kHz,, which is considered as a zonal flow, is observed in low-density ECH plasmas in Heliotron J. The long-range toroidal correlation of the low frequency range become higher on D dominant plasmas in standard configuration of Heliotron J. Interestingly, however, different dependence on isotope ratios, smaller amplitude and coherence in the frequency range, is observed in D plasmas in the magnetic configuration with low-bumpiness. The configuration dependence can be one of factors to explain the difference in isotope effect between tokamaks and helical devices.

Speaker: Dr Shinsuke OHSHIMA (Kyoto University)

Sumary_ohshima2018_提出版.pdf

305 The DEMO fuel cycle – novel technologies for tritium inventory reduction

In the framework of the EUROfusion Programme the EU is preparing the conceptual design of the fuel cycle for a pulsed fusion DEMO. Over the last years, a completely novel and most innovative fuel cycle architecture has been developed, driven by the need to reduce the tritium inventory to an absolute minimum. To achieve this goal, batchwise processes used in the fusion fuel cycle so far were replaced by continuous processes wherever possible. This includes the change from discontinuous cryopumping to mercury based continuous vacuum pumping with zero demand on cryoplant power, and the introduction of thermal cycling ab- and adsorption processes for isotope separation in the tritium plant instead of large cryogenic distillation columns with tritiated liquid hold-ups. To further reduce inventory, the well-known approach to route all exhaust gas through the tritium plant has been abandoned in favor of a three-loop architecture. There, superpermeable metal foils are introduced in the divertor ports to separate a pure DT stream which is then immediately recycled to feed the pellet injection systems. Continuous re-injection of the exhaust gas can artificially increase the wall recycling coefficient and hence allows to increase the burn-up fraction which results in reduced gas throughputs needed to maintain a stable plasma operation at acceptable fuel dilution. To increase the core fueling efficiency, optimization potentials in the design of the high field side guiding tube systems are being exploited. The tritium accountancy system under development will rely on modern, real-time and online tritium instrumentation. Finally, a unified fuel cycle simulator is under development on a commercial software platform in order to identify optimization potentials within the fuel cycle, to allow impact studies, and on a long term to support the development of tailored control and operational strategies. The paper presents the first integrated and consolidated design point of the fuel cycle based on the 2017 European DEMO baseline. It is shown how the DEMO requirements are picked up and affect system level performance. Examples are given for integration issues and how they were solved. Finally, a roadmap is delineated which illustrates the remaining R&D efforts needed to achieve at a validated and complete conceptual design until the mid 2020s.

Speaker: Dr Christian Day (Karlsruhe Institute of Technology)

306 The Potential For Retention of Spin Polarization To Raise Fusion Reactivity

Spin Polarized Fusion (SPF), which increases the DT fusion cross section by 50% and is predicted to yield power gains of 75% in an ITER Q=10 plasma (without SPF), could be demonstrated in the DIII-D tokamak, using recent technological advances. The cross section (probability) for thermal DT fusion is not only temperature dependent, but also depends on the spin orientation of the nuclei, increasing the DT fusion cross section by up to 50%. A self consistent transport calculation predicts up to a 75% increase in fusion power in that ITER scenario. A test of the survivability of spin polarized DT fuel through to the fusion reaction can be obtained by injecting spin polarized D and $^3$He pellets into the DIII-D tokamak. The DT fusion reaction D+T$\to\alpha$+n is isospin equivalent to the reaction D+$^3$He$\to \alpha$+p. Simulation synthetic diagnostic data of the resultant energetic proton fluxes, such as could be measured with a fast ion loss detector, calculated for polarized material with currently available levels of polarization, show that there can be up to a 30% change between the anti-parallel and parallel alignment configurations at several locations near the vessel walls. Spin polarized D is routinely produced in the nuclear physics community. The purity fraction is currently ~40%. D-pellet polarization will have a depolarization decay time of about a year at liquid helium temperatures, which would be sufficient to produce the pellets in Virginia, USA, and then transport them to DIII-D for the proposed polarization survival experiment. We have recently shown that highly (~65%) polarized $^3$He can retain essentially all of its polarization during diffusion through a polymer shell to make a $^ 3$He pellet for injection in the proposed polarization survival experiment. Because the depolarization time for these $^3$He filled pellets at liquid nitrogen temperatures is only a few hours, a device for producing $^3$He would be built onsite at DIII-D, and then the pellets filled shortly before injection into DIII-D. Polarization retention in the proposed D$^3$He experiment would be a breakthrough for fusion. This work was supported by General Atomics Internal Research and Development funds, a grant from the University of Virginia Research and Initiative Fund, and the US Department of Energy through grants DE-FC02-04ER54698 and DE-AC05-06OR23177.

Speaker: Dr Sterling Smith (General Atomics)

FIP_P3_10_summary_slide.pptx

307 Thermal Performance Analysis of Al2O3 - Water Nanofluid as a Coolant in Nuclear Applications

The thermal performance of plasma facing components in a fusion reactor receiving high heat fluxes could be enhanced significantly by using nanofluid which are suspensions of 0.001-10% nanoparticles of <100nm size. Nanofluids show a promising heat transfer enhancement compared to the base fluid. Water-based nanofluids have the potential to deliver much improved high heat flux cooling while retaining all the advantages of water. The exciting prospect of nanofluids has motivated this investigation into their suitability as coolants of a fusion reactor. This paper intends to present a theoretical investigation on energetic feasibility of Al2O3/water nanofluid as coolant streaming inside a smooth horizontal tube. Existing experimental results are utilized to compute the thermo-physical properties, heat transfer coefficient and pumping power of nanofluid. The heat transfer coefficient ratio i.e. the ratio between heat transfer coefficients of nanofluid to the same of base fluid has been calculated from the existing correlations at constant Reynolds number. The derived mathematical model of heat transfer coefficient ratio was validated with data available in existing literatures. The pumping power ratio which is the ratio of pumping power required for nanofluid flow to the same required for basefluid flow has been estimated. The effective increase in heat transfer coefficient makes nanofluid more promising than water for ultrafast cooling in nuclear applications. However, the effective increase in pumping power due to dispersion of nanoparticles in its base fluid makes it unfavorable for efficient heat transfer applications.

Speaker: Mr Sayantan Mukherjee (Kalinga Institute of Industrial Technology,Bhubaneswar,Odhisa(India))

Thermal Performance Analysis of Al2O3.pptx

308 Thermo-hydraulic Analysis of Forced Flow Helium Cooled Cryopanels of Cryopump Using Venecia Code

Cryoadsorption cryopump with large pumping speeds application has been developed at the Institute for Plasma Research (IPR). These pumps are cooled with liquid helium for cryopumping panels below temperature 5K to adsorb hydrogen and helium gases and with gaseous helium for thermal shields at around 80 K during fusion reactor relevant applications. The panels are coated with activated carbon as sorbent. Sorbent with micro-pores adsorbs gases and the pores get saturated after certain duration of pumping operation. During regeneration by increasing the panel temperature adsorbed gases get removed. A cycle of operation is thus followed comprising, cool down from 80K to ~4K and warm up from ~4K to 80K during the normal operation cycle of the cryopump. Cryopanels and shielding panels are mostly hydoformed quilted stainless steel panels with sheet thickness of 1.5mm. Hydroformed panel of size 1000mm (l)x 200mm (w) with the same sheet thickness connected by inlet and outlet tubes are used as 4K cryopanel. Thermohydraulic analyses are carried out in Venecia software developed by Alphysica for the 24 Panel cryopump for different cooling schemes. To investigate the necessary mass flow rates and cool down time, optimized selection of the cryopanel arrangements, flow paths and manifolds is required. Results of cool-down time, mass flow requirement and temperature and velocity profile will be presented for different cooling and regeneration schemes.

Speaker: Mr Samiran Shanti Mukherjee (Institute for Plasma Research)

P3-50-Summary slide_Samiran.pdf

309 Tritium Handling and Recovery System for Accelerator Based 14-MeV Neutron Generator

An accelerator based 14 MeV neutron source is under development to study the fusion neutronics for Indian fusion programs. The neutrons are generated by impinging 10 mA deuterium beam accelerated up to 340 keV energy over a 140 Curie tritium target. Being a system handling tritium-radio-active material, a recovery system is to be designed to minimize airborne tritium effluent releases to well below the permitted limit. In addition, the system should minimize tritium exposure to staff by maintaining low levels of tritium in the Rotating Tritium Target Holder (RTTH). The paper presents the first estimated value of tritium coming out into the exhaust of the accelerator system. A mathematical model is developed to estimate the amount of tritium getting sputtered out of the target. The calculated result is then successfully simulated using SRIM software, and validated using the experimental results available. According to a paper by M.Martone, tritium release from the target at maximum power has been evaluated to be 37 GBq/h experimentally. As per our calculation method and the simulated results, the tritium release is calculated to be 40 GBq/h which is in very close conformance with the claimed value. Based on this primary calculated data a conceptual design of the Tritium Handling and Recovery System (THRS) is also presented. There are a number of technologies available for THR like, metal membrane reactors, cryogenic adsorption on molecular sieve beds, getter beds, cryogenic freezing, high temperature electrolysis, and catalytic oxidation. Today globally, getter bed technology for the tritium separation is in frequent practice. This paper also elaborates the specific selection criteria for development of recovery system. Followed by determining the significance of the selection criteria using the Pairwise comparison (Pugh matrix) approach for weighting the criteria accordingly, and selecting the appropriate technology.

Speaker: Mrs Deepti dubey (ITER-India, IPR, Bhat, Gandhinagar, 382428, Gujarat, India)

FEC-2018_Summary slide.pptx.pdf

310 Tungsten Fuzz Formation on the Nitrided Tungsten Surface

The research goals are determining the effect of nitrogen plasma on the tungsten and comparative analysis of the formation of tungsten fuzz on the helium plasma interaction on the initial surface of tungsten and on the surface of tungsten, previously subjected to nitriding. The experiments were carried out on an imitation stand with a plasma-beam installation. The device provides the following parameters of the plasma flow: the diameter of the plasma flow in front of the target up to 30 mm; the intensity of the magnetic field produced on the axis of the plasma-beam discharge chamber is 0.1 T; the plasma density in the beam is up to 10^18 m^-3; the maximum current in the plasma is 1 A; the electron temperature range of the plasma is 5 15 eV.
All stages of the experiments contained studies of the surface of tungsten using optical and SE microscopy, elemental and X-ray analysis, and determination of the hardness of the surface of tungsten samples.
As a result of the series of experiments on nitridation of tungsten, an optimal nitriding regime was determined that lead to the formation of tungsten nitrides on the surface of the irradiated sample. A series of irradiation experiments were realized on the initial tungsten surface with helium plasma in the plasma-beam discharge regime. On the surface of the samples, a coating was found tungsten fuzz. Experiments have been carried out on the irradiation of tungsten with a helium plasma with a previously nitrided surface. The results of the investigations showed that tungsten fuzz forms on the nitrided surface of tungsten, as well as on the initial surface. On the initial surface of tungsten, the structure of the fuzz is more uniform than on nitrided samples.
Sum up, the conducted experiments showed that nitridation of the tungsten surface does not play an important role in the formation of the tungsten nanostructure as a result of irradiation of tungsten with helium plasma.

Speaker: Mr Timur Tulenbergenov (Institute of Atomic Energy of National Nuclear Center)

Miniyazov_Kaz_single_slide_27th_FEC2018.pdf

10:15 Coffee Break

EX/2 Pedestal & ELM Optimization

311 Impact of ELM control in JET experiments on H-mode terminations with/without current ramp-down and implications for ITER

An important aspect of ITER operation will be the termination of the high confinement H-mode phase ($I_p$ ramp-down phase) in a controlled and safe way. Previous ramp-down studies in JET and other devices focused on aspects related to flux consumption and vertical stability control. In this work the emphasis is on aspects related to W accumulation and its control, which can be particularly challenging in a Be/W wall environment, such as JET or ITER. The dynamics of a slow H-mode ramp-down (to mimic the power ramp-down scenario foreseen for ITER) have been systematically studied in JET during both the $I_p$ flat-top and $I_p$ ramp-down phases, in order to explore the conditions under which W accumulation develops and how it can be controlled using external actuators that are known to affect the impurity transport, such as central electron heating (ICRH in JET) or ELM control (vertical kicks and pellet injection). The use of vertical kicks for ELM control has proven to be an effective method to avoid W accumulation during the H-mode termination phase in JET-ILW. With ELM control the long ELM free phases, typically observed as the plasma approaches the H-L transition, can be avoided, allowing the impurity content of the plasma to be significantly reduced. As a result, the plasma remains in type I ELMy H-mode for a longer period, leading to a slower decrease of the plasma energy, which can mitigate the radial control requirements in ITER. It is found that ELM control with vertical kicks provides not only impurity control but also density control, which is also a key aspect in the ITER ramp-down scenario. Attempts to use pellet pacing for ELM control has resulted, so far, in terminations with low radiation levels but poor density control and further investigation is required to assess the effectiveness of this ELM control approach. In addition to the ELM control studies, other mechanisms affecting the plasma transport properties during H-mode termination, such as central electron heating (ICRH), NBI momentum and particle sources and plasma shape variations (reduced elongation maintaining $q_{95}\sim$constant) during the $I_p$ ramp-down, were also investigated. The full set of experimental observations, as well as the more recent modelling results obtained with the JINTRAC suite of codes will be presented and the implications for ITER discussed.

Speaker: Dr Elena de la Luna (CIEMAT)

delaLuna_IAEA_2018_oral_wide.pdf

IAEA2018 EdelaLuna SummarySlide.pdf

312 Viability of Wide Pedestal QH-Mode for Burning Plasma Operation

Wide Pedestal QH-mode is a new steady ELM-free regime obtained in DIII-D, exhibiting a transport-limited pedestal regulated by broadband turbulence, with improved confinement relative to QH-Mode under the same conditions, attaining $\beta_N\sim 2.3$ and H98y2$\sim$1.6, which increase with power. Toward compatibility with burning plasma conditions, the need for neutral beam torque to initiate and sustain Wide Pedestal QH-Mode has been completely eliminated. Further, the regime has now been sustained for several confinement times with dominant electron heating, at very low torque, without ELMs or core MHD. Recent experiments show that in Wide Pedestal QH-Mode, both pedestal and core confinement uniquely improve when Electron Cyclotron Heating (ECH) augments or replaces Neutral Beam Injection (NBI). This is promising for burning plasma operation where $\alpha$-particles heat electrons. Adding 0.8 MW ECH to 3.8 MW NBI power more than doubles pedestal confinement, increasing pedestal pressure by 50%. Wide Pedestal QH-Mode has now been sustained for several confinement times with up to 77% ECH power (3 MW ECH to 0.9 MW NBI), limited by the available ECH power. High electron temperatures exceeding 12 keV are attained suggesting an internal transport barrier (ITB), which is verified using modulated ECH and ECH location scans to measure electron temperature profile stiffness. A deep well forms in the inner core toroidal rotation profile during intense ECH, characteristic of ITBs. The electron transport stiffness has been similarly studied in QH-Mode in the outer core, showing the electron temperature gradient lies close to a critical gradient. Separately, the regime has been maintained with ITER-relevant shape. These and other new developments support Wide Pedestal QH-Mode regime as a viable solution to avoid ELMs and associated divertor damage in a zero-torque, high-confinement, electron heated scenario at ITER collisionality. This work was supported in part by the US Department of Energy under DE-FC02-08ER54966, DE-SC0014264, DE-FC02-04ER54698, FG02-08ER54984, DE-FG02-08ER54999, DE-AC02-09CH11466 and FG03-97ER54415.

Speaker: Dr Darin Ernst (MIT)

Ernst_EX2-2_IAEA_FEC18_overview_slide.pdf

Ernst_EX2-2_IAEA_FEC18_overview_slide.pptx

ernst_iaea18_talk_EX2-2_v6.pdf

313 Advances in the understanding of the I-mode confinement regime: access, stationarity, edge/SOL transport and divertor impact

The I-mode is an improved confinement regime of tokamak plasmas where an edge transport barrier is observed only in the heat transport but not in the particle transport. This is in contrast to H-mode confinement, which is characterized by transport barriers for both heat and particles. The I-mode does not exhibit any edge localizes modes. Since the particle confinement is low, the I-mode does not suffer from high impurity content. In I-mode, the edge turbulence spectrum is dominated by an instability called the weakly coherent mode (WCM). After substantial I-mode research by the fusion community in the last years, the mechanism which creates a transport barrier in only one of the transport channels is still not understood. An overview of recent I-mode studies on ASDEX Upgrade is given, including L-I and I-H power thresholds, pedestal and confinement properties, extending previous studies to higher Greenwald fractions up to 0.7. The confinement improvement in I-mode is accompanied by a deepening of the edge radial electric field well and a reduction of turbulence with respect to L-mode. New investigations with poloidal correlation reflectometry and correlation electron cyclotron emission diagnostics detect the WCM in the L-mode phase before I-mode starts, showing that the WCM is not exclusive to the I-mode. A newly installed thermal Helium beam allows a precise radial determination of maximum impact of the WCM. A striking feature of I-mode edge turbulence is a reduction of low-amplitude density fluctuations, concomitant with the appearance of strongly intermittent high-amplitude density bursts in the plasma edge inside the separatrix. These density turbulence bursts are linked to the WCM. After their generation, they are expelled from the plasma and appear later in the divertor, observed by bolometry, infrared thermography and probes. Moreover, stationary I-modes have been obtained recently with neutral beam injection heating. The stationarity allows the characterization of scrape-off layer (SOL) fall-off lengths of density and temperature. While the former are similar to L-mode plasmas, the latter are comparable to H-mode plasmas, indicating that I-mode properties are also found in the SOL. Infrared thermography data yields information on the scrape-off layer power fall-off length and divertor loads, and implications for future devices are discussed.

Speaker: Dr Tim Happel (Max-Planck-Institut für Plasmaphysik)

2018-10-24_Happel_IAEA_summaryslide.pdf

2018-10-24_Happel_IAEA_talk_final2_woBackup.pdf

314 High Fusion Performance in Super H-Mode Experiments on Alcator C-Mod and DIII-D

The “Super H-mode” regime is predicted to enable pedestal height and fusion performance substantially higher than for standard H-mode operation. This regime exists due to a bifurcation of the pedestal pressure, as a function of density, that occurs in strongly shaped plasmas above a critical density. Experiments on Alcator C-Mod and DIII-D have achieved access to the Super H-Mode regime, and obtained very high pedestal pressure, including the highest pedestal pressure ever achieved on a tokamak ($p_{ped}$~80kPa) in C-Mod experiments operating near the ITER magnetic field. DIII-D Super H experiments have demonstrated high performance, including the highest stored energy in the present configuration of DIII-D (W~2.2-3.1MJ), while utilizing only about half of the available heating power ($P_{heat}$~6-12 MW). These DIII-D experiments have achieved the highest value of peak fusion gain, $Q_{DT,equiv}$~0.5, ever achieved on a medium scale (R<2m) tokamak. Sustained, stationary high performance operation has been achieved utilizing n=3 magnetic perturbations for density and impurity control. Super H-Mode access is predicted for ITER and expected, based on both theoretical prediction and observed normalized performance, to enable ITER to achieve its performance goals (Q=10) at Ip < 15MA, and to enable more compact, cost effective DEMO designs. We present extensive comparisons of Super H theory to experiments on C-Mod and DIII-D, predictions for Super H access on JET, JT-60SA & ITER, and coupled core-pedestal predictions of fusion performance on existing and future devices. This work was supported in part by the US Department of Energy under DE-FG03-95ER54309, DE-FC02-99ER54512, DE-FC02-04ER54698, and DE-FC02-06ER54873.

Speaker: Dr Philip Snyder (General Atomics)

Snyder_IAEA_ex2-4.pdf

Snyder_summary_ex2-4.pdf

Snyder_summary_ex2-4.pptx

315 Plasma shape and fueling dependence on the small ELM regime in TCV and AUG

A series of experiments has been conducted at AUG and TCV to disentangle the role of fueling, plasma triangularity and closeness to a double null (DN) configuration for the onset of the small ELM regime. At AUG, the role of the SOL density has been revisited. Indeed, it turns out that a large density SOL is not a sufficient condition to achieve the type-II (small) ELM regime. This has been demonstrated with a constant gas fueled plasma close to DN which has been progressively shifted down, relaxing therefore the closeness to DN at constant. As the plasma is moved down, Type-I ELMs are progressively restored, finally being the unique ELM regime. It is observed that not only the pedestal top profiles are unchanged, but also the SOL profiles remained unaffected by transition from Type-II to Type-I ELMs. We conclude that the separatrix density is not the unique key parameter and it is hypothesized that the local magnetic shear, modified by the closeness to DN, could play an important role. A small ELM regime with good confinement has been achieved at TCV, a full carbon machine featuring an open divertor. A systematic scan in the fueling rate has been done for both medium and high triangularity shapes. For the latter case, a configuration close to a DN configuration, the stored energy and the pedestal top pressure increase by 5% and 30% respectively compared to the medium triangularity case. For both shapes, as the D2 fueling is increased, the Type-I ELM frequency decreases and small ELMs are observed in between large ones. Finally for the high triangularity, at the maximum fueling rate, the large ELMs are fully suppressed and only the small ELMs remain. As observed in JET and AUG, the pedestal pressure degrades with increasing fueling, up to 40% for the high triangularity scenario, although the stored energy remains almost unchanged. It is also observed that, for both shapes, the density at the separatrix increases with the fueling rate, reaching $n_{e,sep}/n_G$ ~0.3 at $n_{e,av}/n_G$~0.75. The small ELM regime at TCV is associated with a coherent mode at about 30 kHz seen by the magnetic probes located at the outboard midplane. The outer target heat loads from IR tomography are reduced by more than a factor of 5 when transiting towards the small ELM regime.

Speaker: Dr BENOIT LABIT (Swiss Plasma Center (SPC) EPFL SWITZERLAND)

Labit_FEC2018_slides_EX2-5.pptx

Labit_fec2018_summary_slide.pptx

12:30 Lunch

EX/3 Plasma Performance & Control

316 Integrated operation of steady-state long pulse H-mode in EAST

Recent EAST experiment has successfully demonstrated long-pulse steady-state scenario with a good plasma performance through the integrated operation since the last IAEA in 2016. A discharge with a duration over 100s has been obtained with multi-RF power heating and current drive. Plasma parameters are as follows, plasma current Ip=0.4 MA, poloidal βP ~1.2, toroidal magnetic field BT=2.5 T, elongation κ=1.6, the safety factor at the 95% normalized poloidal flux surface q95 ~6.6. The zero-loop voltage and pulse length (~ 250 times the current relaxation time) indicate the really steady state condition. Small ELMs were obtained in this long pulse H-mode discharge which facilitates the RF power coupling in the H-mode phase. In the operation, the optimization of X-point, plasma shape, the outer gap and local gas puffing near LHW antenna were investigated to maintain RF power coupling and particle exhaust and to avoid formation of hot spot on the 4.6 GHz LHW antenna. Global parameters of BT and line averaged electron density were optimized for higher current drive efficiency of LHW and on-axis deposition of ECH. A peaked electron temperature profile was observed with a weak ITB at rho ~0.4. No obvious MHD instabilities were found in the whole discharge. The maximum tungsten divertor temperature monitored by the IR camera shows the temperature raises quickly in several seconds and reaches a stable value, ~500 oC. As a key element, wall conditioning was addressed before long pulse plasma operation. Several difficulties are reported in the development of this 100s long pulse discharge. To achieve the next goal (≥400s long-pulse H-mode operations with ~50% bootstrap current fraction), 0-D predictions have been carried out. The modelling suggests that steady-state high performance will require not only increased injected power, but also significantly improved energy confinement quality. The recent long pulse H-mode has demonstrated several key elements and will increase a confidence in achieving high performance, steady state discharges with more key elements in integrated control on EAST. This work was supported by the National Magnetic Confinement Fusion Program of China No.2015GB102000, No. 2015GB110005 and No.2015GB103000.

Speaker: Prof. Xianzu Gong (Insititute of Plasma Physics, Chinese Academy Sciences)

EX/3-1 Summary Slides_2018_Gong_v3

EX3-1_XGong_IAEA FEC 2018_Final.pdf

IAEA_FEC2018_EX3-2_GONG_Final.pdf

317 Developing steady state ELM-absent H-mode scenarios with advanced divertor configuration in EAST tokamak

The divertor properties of a two nearby magnetic poloidal nulls (2-NDN) configuration have been recently investigated in steady state (Vloop<0) H-mode plasmas, (H98=1), Edge Localized Modes (ELM) absent, on EAST tokamak. Due to the location of Poloidal Field (PF) coils and target plates in EAST, the secondary null could be moved around from the primary one to form a magnetic configuration that features either a contracting or flaring geometry near the plate. An increase of the connection length by ~30% and flux expansion in the outer strike point (SP) region by a factor of ~3 with respect the single null (SN) case, in all the upper 2-NDN discharges have been achieved. A reduction of peak heat loads, of the same order of flux expansion increase, on the upper full W divertor targets, both in L-mode and H-mode discharges, has been observed consistently with theory predictions and predictive 2D edge simulations. In all the 2-NDN steady-state discharge the ELMs activity was quiescent, indicating a possible non-linear interaction between the downstream magnetic topology and the upstream kinetic gradients. Another potential explanation of the quiescent ELMs could be linked with the role of electrostatic edge coherent mode (ECM) which resides in the pedestal region and whom topological structure could be affected by variation of the local connection length. The ECM contribution to ELMs behavior on 2-NDN scenario is presently under investigation.

Speaker: Dr Nicola Vianello

fec_2018_vianello_ex32.pdf

318 Integration of the high- N hybrid scenario to a high performance pedestal, stable zero torque operation and a divertor solution

DIII-D experiments have demonstrated the expansion of the high-betaN hybrid scenario to the high density levels necessary for radiating divertor operation, leading to pedestal enhancement, and showed how the choice of injected impurity impacts the effectiveness of a radiating mantle solution, as well as the impurity transport to the core and the divertor. The scenario was made robust to systematic changes in EC power deposition location and current drive magnitude or heating injection, and was extended to zero beam torque, where the plasmas are passively stable with and without EC power. Coupling a high-performance core to an acceptable heat flux divertor is a crucial step for ITER and any fusion reactor. This work presents results on all the necessary ingredients, implemented in the high betaN hybrid scenario: high density, on- and off-axis electron heating and current drive, pedestal enhancement, puff-and-pump and radiating mantle techniques and impurity transport. 2017 experiments confirmed ELITE simulations which predicted that a near double null configuration and reactor-relevant q_95>5.5 are required for the pedestal enhancement with density. The impact of impurities used for the radiating mantle on the core of the plasmas, as well as their transport in the edge and divertor will be discussed.

Speaker: Dr Francesca Turco (Columbia University)

turco_iaea2018_hybrids.pdf

319 Optimisation of JET-DT and ITER operation by developing an understanding of the role of low-Z impurity on the H-mode pedestal

Impurity seeding via injection of neon (Ne) or nitrogen (N) will be mandatory in ITER Q=10 reference scenario to reduce inter-ELM power load to the divertor within the engineering limits. The challenge is achieving the scenario requirement of $ H_{98(y,2)}$=1, $\beta_N $=1.8, $\frac{(n)}{n_{GW}}$=0.85, $\delta $=0.4, with a high radiative divertor. These conditions necessitate a high pedestal temperature which leads the pedestal to playing a key role in this challenging integration. Unravelling the mechanism that, in the absence of carbon in the plasma composition leads to a decrease in the pedestal temperature is critical in predicting the pedestal pressure in ITER. It is important to learn how to use the extrinsic impurity to optimise the pedestal temperature in high radiative scenarios. This paper aims at (1) reviewing our understanding of the effect of carbon (C), N and Ne-seeding on the pedestal pressure and temperature, (2) assessing whether the peeling ballooning stability limits the pedestal pressure, and (3) determining which instabilities are causing heat and particle transport. In JET-ILW this limitation on the pedestal temperature is alleviated with the injection of nitrogen, or C in low and high-$\beta_N$ plasmas. Seeding Ne can result in opposite behaviour on the pedestal density depending on the collisionality $ \nu^*_e $ and $\beta_N $, but in all cases seeding Ne does not lead to an increase of temperature, unlike N or C. A detailed analysis of the differences in the electron and ion pedestal profiles in the high-$\beta_N$ plasmas indicate that the difference between C and Ne-seeding can be down to the value of collisionality $ \nu^*_e $ , but also the value of ExB shear considering the difference in $\bigtriangledown T_{i,\alpha_{max}}$ and $\bigtriangledown \Omega_{tor,\alpha_{max}}$ at the position of the maximum normalised pressure gradient. Similarly, seeding $CD_4$ in the low-$\beta_N $ plasmas increases $\bigtriangledown T_{i,\alpha_{max}}$ and $\bigtriangledown \Omega_{tor,\alpha_{max}}$. Detailed analysis with the GENE code will clarify which instability is at the origin of the difference in the pedestal temperature. The peeling ballooning stability has been assessed with MINERVA-DI code. The plasmas considered have the operational points (OP) of the high and low-$\beta_N $ plasmas within 20% of the stability boundary.

Speaker: Dr Carine Giroud (CCFE)

cgiroud_iaea2018_oral_v9.pdf

cgiroud_preprint_iaea2018_v05.pdf

320 Increasing the Density in W7-X: Benefits and Limitations

As the first comprehensively optimized stellarator, Wendelstein 7-X (W7-X) is an essential experiment to study high density operation in this kind of device. This contribution presents first experiments on the density dependence of the energy confinement in W7-X and limitations of the achievable density. Theoretical predictions and empirical scaling laws for the energy confinement time in stellarators (e.g. the ISS04) predict a positive correlation between the plasma density and the energy confinement time. However, this might not be valid for plasma operation close to operational limits. Hence, the energy confinement time scaling and the presence of operational limits have to be studied as an intertwined system. The experimental exploitation of W7-X has only started, however, the gradual completion of the machine capabilities is an ideal opportunity to map out the configuration space and to identify key issues on the route to high-performance long-pulse operation. In the first two experimental campaigns, featuring a limiter and a test divertor configuration, the energy confinement time has been analyzed. A positive density dependence has been found and the scaling coefficient is close to the expectation from ISS04. During these experiments, however, radiative collapses have been observed. Such a radiative density limit is predicted by simplified analytical models. Such a model has been applied to W7-X in order to estimate a critical density and in purely gas-fueled hydrogen plasmas, no stable plasma operation has been achieved above this density. It has been observed that the critical density also depends on the magnetic configuration, which directly relates this issue to scenario development. Furthermore, first experiments with pellet-fueling showed densities well above the critical density, which indicates the importance of profile and fueling effects. These experiments confirm that an increasing density is indeed beneficial for the energy confinement, at least in the currently accessible density range. It remains to be shown that this trend extrapolates to the high-performance plasmas W7-X was designed for. The experiments have also shown, however, that high-density operation involves a careful scenario development, as fueling issues and radiative instabilities limit the currently accessible operational space of W7-X in its current state of completion.

Speaker: Dr Golo Fuchert (Max-Planck-Institut für Plasmaphysik, Greifswald, Germany)

IAEA_oral_fuchert.pdf

IAEA_oral_fuchert.pptx

summary_slide_fuchert.pdf

321 Scenario development for DT operation at JET

The JET exploitation plan foresees D-T operations in 2019-20. With respect to the first D-T campaign in 1998, when JET was equipped with a C wall, the experiments will be conducted in presence of a Be-W ITER-like wall and will benefit from an extended and improved set of diagnostics and higher available additional power. Among the challenges presented by operations with the new wall there are a general deterioration of the pedestal confinement, the risk of heavy impurity accumulation in the core, and the requirement to protect the W divertor from excessive heat loads. Therefore, an intense activity of scenario development has been undertaken at JET during the last three years to overcome these difficulties and to achieve a stationary scenario of the duration of 5 seconds featuring H$_{98}$>0.9, W$_{th}$≈10-12 MJ towards the lowest values of ρ* and ν* achievable on JET. Two complementary scenarios are being developed to approach the problem of developing a scenario suitable for high-performance D-T operation. The baseline scenario (β$_N$~1.8 and H$_{98}$~1.0) concentrates mainly on pushing the operation towards the high current and field limits with a relaxed current profile, whereas the hybrid scenario (β$_N$~2-3 and H$_{98}$>1.0) exploits the advantages of operating at high normalised beta with a shaped current profile above unity. Encouraging results were achieved for the baseline scenario at 3MA/2.8T and for the hybrid scenario at reduced plasma current (2.2-2.5MA/2.8-2.9T). High-performance plasmas with H$_{98}$~0.9 producing ~3 10$^{16}$ neutrons/s were obtained for >5 energy confinement times (~1.5s). A third scenario, has also been developed for alpha particle studies. This scenario aims at maintaining high plasma performance for 1-2s to generate a significant population of $\alpha$-particle for the $\alpha$-particle studies and deliberately omits ICRH heating to avoid creating RF driven fast particles, which could mask the effect of the fusion-generated $\alpha$-particles. In these pulses ICRH induced TAEs were observed after the NBI switch-off compatibly with the beam fast ion slowing-down time. The results of all scenarios have been the object of an extensive activity of code validation and modelling and extrapolated to the target D-T scenarios.

Speaker: Dr Luca Garzotti (United Kingdom Atomic Energy Agency - Culham Centre for Fusion Energy)

Summary slide V2.pdf

IFE/1-EX/2 P4 Posters

322 Advances in the understanding of the I-mode confinement regime: access, stationarity, edge/SOL transport and divertor impact

Speaker: Tim Happel (Max-Planck-Institut für Plasmaphysik)

2018-10-24_Happel_IAEA_summaryslide.pdf

323 Demonstrations of foam shell and infrared heating methods for FIREX targets

Speaker: Dr Akifumi Iwamoto (National Institute for Fusion Science)

324 High Fusion Performance in Super H-Mode Experiments on Alcator C-Mod and DIII-D

Speaker: Dr Philip B. Snyder (General Atomics)

325 Impact of ELM control in JET experiments on H-mode terminations with/without current ramp-down and implications for ITER

Speaker: Dr Elena de la Luna (CIEMAT)

326 Liquid DT Layer Approach to Inertial Confinement Fusion

Speaker: Dr Ray Leeper

327 Plasma shape and fueling dependence on the small ELM regime in TCV and AUG

Speaker: Dr BENOIT LABIT (Swiss Plasma Center (SPC) EPFL SWITZERLAND)

328 Production of keV-Temperature Plasma Core with Magnetized Fast Isochoric Heating

Speaker: Dr Shinsuke Fujioka (Institute of Laser Engineering, Osaka University)

329 Progress in the study of the “Shock Ignition” approach to Inertial Confinement Fusion

Speaker: Prof. Dimitri Batani (Université de Bordeaux)

330 Two-colors mixed petawatt laser designed for fast ignition experiment

Speaker: Dr Yasunobu Arikawa

331 Viability of Wide Pedestal QH-Mode for Burning Plasma Operation

Speaker: Dr Darin Ernst (MIT)

P4 Posters

332 A Diagnostic Approach for the Detection of Spatially Distributed Low Energy Confined Runaway Electrons in the ADITYA-U Tokamak by means of Synchrotron Emission Imaging in the Sub-millimetre Wavelength Band

In recent years, the studies of Runaway Electron (RE) generation and energy dynamics in tokamaks have gained great importance from the theoretical and experimental perspective. The generation of high power RE beam during the plasma disruption may damage in-vessel components. Therefore, it is important to study and to suppress the REs for the safe operation of the large size tokamaks, such as ITER tokamak. This demands an improved, robust and sensitive RE diagnostic methods to provide essential observations of confined REs when they are in the early stage of their energy and population growth. The RE-diagnostic data can be utilized for validation of the theoretical models and also to study the efficiency of the RE mitigation techniques. Out of several RE diagnostic methods, observation of the synchrotron radiation emission (SRE) from REs is an established method to detect the confined REs and studied in the several tokamaks using the Visible and IR cameras where the lower observed energy of the REs was reported typically more than 20MeV. Signature of REs and supra-thermal electrons in the cyclotron emission range is often reported from several tokamaks where the energy is in the sub-MeV range. Measurements of REs in the intermediate range from 0.5 MeV to 20 MeV is always been performed by the HXR and Gamma-Ray spectrometers. Non-imaging SRE measurements of the low energy REs (~2-7 MeV) performed in the FT-2 tokamak in the range of 106-156 GHz. This motivates to design a diagnostic that can detect SRE from the low energy confined REs in the sub-millimetre band (THz-band). In this paper, a imaging diagnostic approach has been proposed for the first time to capture spatiotemporally resolved SRE pattern of the low energy confined REs in the ADITYA-U tokamak. In order to design the diagnostic, a detailed forward modelling of the RE dynamics in the momentum space performed considering the experimental evolution of the plasma parameters. The simulated RE parameters were utilized to predict SRE signal level at the given detector location and the diagnostics parameters were optimized. Expected spatial distribution of the SRE brightness images as seen by the THz-camera has also been modelled. From the modelling results, it has been established that the proposed design can provide spatiotemporally resolved SRE images of the confined REs in the energy range 1-20 MeV.

Speaker: Dr Shwetang Pandya (India Institute for Plasma Research, Bhat, Gandhinagar, 382-428, India)

333 ADITYA Experimental Results of Core Ion Temperature Measurements on ADITYA Tokamak Using Four Channel Neutral Particle Analyser

Core-ion temperature measurements are routinely carried out by the energy analysis of passive Charge Exchange (CX) neutrals escaping out of the ADITYA-tokamak (Minor radius a=25 cm, major radius R=75 cm) plasma using a 45-degree parallel plate electrostatic energy analyzer [1]. The temporal evolutions of peak ion temperature in the core regime [typically 80 eV to 120 eV for Aditya circular ohmic plasma] as estimated by analyzing the energetic neutral spectrum obtained on four Channeltrons of multichannel data acquisition system [MEASAR-minus-A measurement system for CEM array, Dr. Sjuts optotechnik GmbH, Germany] for several plasma discharges in Aditya, provides an estimate for the core neutral hydrogen [H0] density and its evolution with time. Expected neutral density in the core regime has been estimated for several APPS discharges. The Charge Exchange Diagnostic system on Aditya [2] and data analysis techniques (using numerical algorithms developed) for NPA measurements are also described.Effect of Ion cyclotron radio frequency heating (ICRH) on Ti(0) is observed and reported here, which shows additional increase of Ti(0) up to 60% for the set of plasma discharges investigated herein.

Speaker: Mr Kumar Ajay (IPR)

Preprints-CXD.pdf

THE SUMMARY PAGE.pdf

334 Analysis of Electron Cyclotron Wave Assisted Plasma Start-up in SST-1

In superconducting tokamaks, electric field generated by the central solenoid (CS) for plasma start-up is generally less than that for non-superconducting tokamaks due to the requirement of a robust vacuum vessel and cryostat without insulating break. Moreover, with the CS made of NbTi conductor, there is limitation to maximum dI/dt in the coil to avoid stress limits, resulting in limited loop voltage. To ensure reliable start-up, electron cyclotron wave (ECW) assisted pre-ionization has been applied in several superconducting tokamaks. We initiated the study of start-up in SST-1 with a 0D model and show that ~100 kW of ECW power must be absorbed for start-up for an initial hydrogen atom density NH (t=0) ~4x1018 m-3, an error field Berr=1 mT, carbon and oxygen impurity fractions nC/ne=nO/ne=0.5%, and an EC beam radius of ~5 cm. These findings agree well with the temporal evolution of discharges. However, the 0D model is not sufficient for investigating the physical processes as it lacks radial variation of electron density and temperature, transport, and localization of the ECW power. In this paper a one-dimensional (1D) model that includes radial transport to study ECW assisted start-up is reported. The 1D model comprises of five equations, viz. energy and particle transport for electrons and hydrogen ions and a toroidal current equation. Electrons are assumed to be heated by ECW and Ohmic power and lose energy via several processes. Ions are heated only by the equipartition energy transferred from electrons and lose energy by charge exchange between hydrogen atoms and ions. We consider cylindrical symmetry, on-axis ECW power absorption and the Bohm diffusion. Reaction rate coefficients are calculated using the Average Ion Model. The present study indicates that with increasing initial hydrogen atom density, greater ECW power is required for start-up. This result is attributed to the power loss from ionization and equipartition. The required ECW power thus depends weakly on direct power loss caused by Berr and radiation loss by impurities. These results imply that controlling the initial hydrogen atom density, suppressing Berr, and reducing the impurity density are all useful for reliable start-up. Comprehensive analysis of start-up and the physical processes those dominate the radial distribution of parameters, as the discharge evolves, will be reported.

Speaker: Mr Amit Kumar Singh (ITER-India, Institute for Plasma Research)

ANALYSIS OF ELECTRON CYCLOTRON WAVE ASSISTED PLASMA START - UP IN SST - 1

Summary_Slide_Amit_Singh_FEC_2018.pdf

335 Anomalous Absorption and Emission in ECRH Experiments Due to Parametric Excitation of Localized UH Waves

The extraordinary pump wave two-plasmon decay instability TPDI is analyzed under conditions when only one of the parametrically driven upper hybrid (UH) waves is trapped in the vicinity of the density profile local maximum. It is shown that under these conditions the excitation of absolute TPDI is possible due to a finite width of the microwave pump beam. Its threshold and growth rate are determined. The pump depletion and the secondary decay instability of the localized UH wave are considered as the most likely moderators of primary TPDI and clarify their role in its saturation. We also estimate the pump power fraction gained anomalously throughout the two-UH-plasmon decay. The general consideration is accompanied in the paper by the numerical analysis performed for the experimental conditions typical of the off-axis X2-mode ECRH experiments at TEXTOR. Based on the proposed model the radiance temperature of electromagnetic waves emitted in the high-field-side direction at the frequency close to half the pump frequency is estimated. It is also shown that the nonlinear coupling of the daughter UH waves with the pump could lead to the measurable level of the plasma emission at the 3/2 harmonic of the pump, as it happens in the laser driven inertial fusion experiments. The parametric excitation of trapped UH waves in the O1-mode ECRH experiments is discussed as well. The threshold in this case is shown to be higher (several hundred kW depending on the plasma parameters) than for the X2-mode scenario whereas the growth rate is large enough (in the range of 107 s-1) to expect the non-linear saturation of the instability.

Speaker: Prof. Evgenii Gusakov (Ioffe Institute)

Gusakov_sum_slide.pptx

336 Application of TEM to study the changes in sub-surface defects in Tungsten samples as a function of annealing temperature

In a nuclear fusion reactor, hot and dense D-T plasma is confined using a combination of magnetic fields in a toroidal shaped vacuum vessel. Interaction of this plasma with the wall materials of vacuum vessel is one of the very important areas of interest as plasma-wall interactions will decide the operational life-time of the reactor in terms of plasma as well as material stability. The choice of the wall-material hence becomes an important factor and high atomic number materials such as tungsten and its alloys are currently identified as candidate materials due to their relatively low H-isotope affinity. However, high energy neutrons and alpha particles produced in the fusion reaction can introduce sub-surface defects in tungsten, which may lead to H-isotope trapping through these defective sites. In-order to understand the effect of these defects, it is critical first to identify them. The defects concerned here, such as dislocations, are like bulk features of the materials and cannot be identified using surface characterization equipment such as Scanning Electron Microscope (SEM). Transmission Electron Microscope (TEM) is one of the very few instruments which can identify these meso-scale sub-surface defects. In the work discussed here, we had used a 300 kV TEM to identify these defects in tungsten (W) samples. TEM microscopy of the as received W samples (cold rolled) was carried out. Grains were observed to be elongated and the dislocation density is very high. Later the W samples were subjected to annealing at various temperatures ranging from 773 to 1838 K. The annealing was carried in a vacuum furnace under a reducing atmosphere of Argon and Hydrogen mixture. A base pressure of 10-5 mbar was obtained before the Argon, Hydrogen mixture was introduced. The effect of annealing temperature on the changes in defect distribution and restructuring was studied using TEM. Defect density is observed to reduce with increase in annealing temperature (below recrystallization temperature), though there is not much change in grain size. However, above recrystallization temperature, the grain size was observed to change from elongated to regular shape while the defect density was reduced. Present work also explains in detail about the sample preparation procedure adopted for preparing the W samples for TEM analysis.

Speaker: Mr Satyaprasad Akkireddy (Institute for Plasma Research)

FEC2018_EX-P4-12_Satyaprasad_IN.pdf

337 Beam Ion Performance and Power Loads in the ITER Pre-Fusion Power Operating Scenarios (PFPO) with Reduced Field and Current

The ITER Pre-Fusion Power Operating (PFPO) phase will include half-field/half-current (2.65T, 7.5 MA) and one-third field (1.8T, 5MA) operating scenarios, which ought to allow H-mode access even with limited heating [1].

While PFPO-1 relies only on ECRH and ICRH to achieve the H-mode, in PFPO-2 also the neutral beams will be applied. In the PFPO phases, the plasma will consist of either hydrogen or helium, and will operate at about half of the Greenwald density. Beam operation at low densities requires lower acceleration voltages due to shine-through constraints, so that the maximum beam energy in PFPO is limited to below 870 keV for He plasma.

The goal of this contribution is to determine power loads, due to both charged and neutral particles, to the ITER first wall from neutral beam heating in both the one-third and half-field scenarios, as well as determine the over-all beam performance (heating, current-drive and torque to the plasma) using the full beam capabilities envisaged for both scenarios. The ASCOT suite of codes was used for this purpose since it allows including the effect of ferritic inserts which, due to the lowered field values, can not work in the manner they were designed for. Since the pre-fusion phase will also serve as a relatively benign environment for testing various ITER subsystems, notably ELM mitigation methods, we shall also address the effect of ELM Control Coils (ECC) on fast ion containment.

In the absence of the ECC’s, the beam ions are found to be very well confined. For instance, in the half-field scenario, using the full beam power of 33 MW, power losses are less than 0.1%, with peak power of 130 kW/m2. Shine-through, on the other, is non-negligible: even in the flat-top phase of the discharge the shine-through was 1.8% of the 870 keV beam power, with a corresponding peak power of 680kW/m2. Additional simulations were carried out to determine the electron density resulting in a peak power load of less than 1MW/m2. By varying electron density while keeping the plasma quasineutral and the plasma composition constant, the critical density was found to be approximately 4·1019m-3.
[1] M Schneider et al., ‘Modelling of third field operation in the ITER pre-fusion power operation phase’, in this conference

Speaker: Dr Taina Kurki-Suonio (Aalto University)

beam-ion-performance.pdf

SummarySlide.pptx

338 Broadband Characterization of High Temperature Black Body Source with Fourier Transform Michelson Interferometer for ECE Measurements

In a tokamak electron cyclotron emission (ECE) is measured to determine electron temperature profile and its evolution. Michelson interferometer (MI) diagnostic is capable of measuring the spectrum of the ECE in a wide spectral range (70-500 GHz). Usually MI is calibrated with hot-cold technique. The lab calibration of the MI diagnostics is carried out locally with room temperature and cold source. The absolute calibration of the diagnostics is done with transmission lines, bends, mode converters etc. During absolute calibration signal is below noise level and very long integration time is required to improve S/N ratio. Hence a high temperature calibration source is required to reduce the integration time. This paper deals with the design, development and characterization of a high temperature black body source. This source has been developed by precise machining of cones on a metallic surface and then coating it with silicon carbide paste and electrically heating to a temperature of 873 K. The broadband characterization of this high temperature source has been done with hot - cold technique. Initially, the calibration factor of the system is determined by periodic switching between the room temperature source (RAM material) and the cold source (LN2 at 77 K). The calibration factor obtained from two sources at known temperatures is used to determine the radiation temperature of the unknown high temperature / hot black body source by Fourier transform MI over a wide frequency range of 70 - 1000 GHz. The characterization process will be described in the paper in detail. The radiation temperature of the hot source measured during characterization was found to be in the range 737 - 755 K in entire band. The radiation temperature was about 125 K below the physical temperature of the hot source due to radiation losses. Dips were observed at frequencies 557 GHz and 753 GHz indicating the presence of water absorption lines as expected. The broadband characterization of high temperature / hot black body source with MI has been carried out successfully and results have been presented.

Speaker: Mr Abhishek Sinha (Institute for Plasma Research)

Summary Slide.pdf

339 Chord Average Density Measurement using Microwave Interferometry in LVPD

Microwave interferometer diagnostic is designed and installed for carrying out chord averaged density measurements for plasma density between $ \sim 5\times 10^{10}-6\times 10^ {11} cm^{-3}$ respectively in the Source and Target plasma regions of Large Volume Plasma Device (LVPD). These regions are developed in LVPD by the introduction of large Electron Energy Filter (EEF). This helped in making LVPD plasma suitable for investigating Electron Temperature Gradient (ETG) turbulence, a major source of plasma loss in fusion devices. In order to get hands on information about plasma density, the concept of microwave interferometry is conceived. Measurements made by this technique will be compared with density obtained using conventional Langmuir probes. Even though, Langmuir probe diagnostic is widely used in most of the low temperature plasma devices but electron temperature estimated by it suffer with certain degree of error because of measurement uncertainty of $ 10 \% $, which subsequently corrupts estimate of plasma density. This has prompted us to develop a resident diagnostic based on microwave interferometry for density measurement, which can provide suitable calibration to density measurements made by Langmuir probes. This paper will present results on design details of microwave diagnostic and its application to LVPD plasma. Plasma of different densities will be produced by varying heating current to cathode, for test and validating the diagnostics. A comparison of chord averaged density measured by microwave interferometry with Langmuir probe data will be presented.

Speaker: Mr Pankaj Kumar Srivastava (Institute for Plasma Research)

summary_slide_pankaj.pdf

340 Controlling Plasma Rotation using Periodic Gas-puff in ADITYA-U Tokamak

Plasma rotation and its shear in the edge and scrape-off-layer (SOL) region plays an important role in determining overall confinement of tokamak plasmas. The sources of spontaneous generation of these rotations are still not fully understood. Furthermore, to answer the questions like whether they modify the electric field profile or electric field profile modifies the rotation and its shear, the radial profiles of toroidal and poloidal plasma rotation have been measured in ADITYA-U [1-2] in presence and absence of multiple periodic fuel and neon gas-puffs. Further in typical ADITYA-U discharges, effects of plasma density and different MHD modes on plasma rotation are studied. The results are compared with neo-classical estimations. Plasma rotation velocity is deduced from Doppler shift of the observed line emissions in UV and Visible wavelength range. Carbon spectral emission lines at 229.69, 227.09 and 529.01 nm from C2+, C4+, and C5+, respectively are used to estimate the rotation velocity. The collection optics, installed on a tangential viewport of the tokamak, contains three line-of-sights giving a radial profile of rotation velocity. The Doppler shift of the above spectral lines are measured using a high-resolution 1m f/8.7 Czerny Turner spectrometer equipped with 1800g/mm grating coupled to a fast CCD detector. The details on the development of the diagnostics with an emphasis on the results obtained from ADITYA-U plasma rotation profile will be discussed. References : [1] Bhatt S.B. et al 1989 Indian J. Pure Appl. Phys. 27 710. [2] J Ghosh et al, FIP/P4-46, 26th IAEA Fusion Energy Conference (2016)

Speaker: Mr Gaurav Shukla (Pandit Deendayal Petroleum University)

Summary.pptx

341 Design and Development of 140 GHz D-Band Phase Locked Heterodyne Interferometer System for Real Time Density Measurement

In a tokamak, an interferometer system measures plasma density using an electromagnetic wave which experiences a phase shift with respect to a reference signal while passing through the plasma column. In millimetre wave spectrum, usually homodyne and heterodyne systems are used to determine phase information. One of the limitations of the homodyne scheme was its inability to differentiate the increase or decrease in phase and corresponding plasma density. Hence a heterodyne scheme was required which can detect the increase or decrease of phase with precision and is capable of real time density measurement with feedback control. This paper deals with the design, development and characterization of a 140 GHz D-Band phase locked heterodyne interferometer system with real time density measurement. Here the transmitter and receiver are phase-locked by a reference crystal oscillator of 100 MHz to provide a stable signal and minimize errors in measurement due to phase mismatch. This phase locking provides a highly stabilised intermediate frequency (IF) of 2 GHz. The IF signal is further down converted by IQ mixer to 100 KHz I & Q signals in form of sine and cosine waves. These signals are used calculate the absolute phase by zero crossing method. These signals are digitized by 12-bits ADC. The controller uses the digitized signals to generate real time density signal which can be used for density feedback control. The system has a temporal resolution of 5 µs and phase error measurement of 0.07 radians. The performance of the microwave and RF electronics has been shown in the paper. The overall performance of the heterodyne phase locked interferometer system with AGC signal has been shown. Laboratory tests results and plasma results after installation of the system on Aditya tokomak has been presented. Real time density signals and actual density signal has been measured for various plasma shots. One typical plasma discharge with gas puff is shown. (a) Heterodyne Interferometer System (b) Plasma discharge with gas puff

Speaker: Mr Umesh Kumar Nagora (Institute for Plasma Research)

slide.pdf

342 Design and development of Passive Charge Exchange Neutral Particle Analyzer for ADIYA-U Tokamak

Passive charge exchange diagnostic is well established technique for measuring core-ion temperature of tokamak plasma. Energetic neutral particles that are formed due to charge exchange of plasma ions with neutral atoms, can escape from the plasma. These neutral atoms that are re-ionized and analyzed using analyzer can provide information about the energy distribution of plasma ions [1]. A passive charge exchange neutral particle analyzer has been designed and indigenously developed for Aditya-U tokamak. It consists of a H2 gas-cell based stripping cell, a 45-degree parallel plate electrostatic energy analyser, Channel electron multipliers as detectors and an integrated measurement system CEM-IMS as DAQ. The stripping cell, which is made of soft iron, is a 200 mm long narrow tube of diameter 4 mm. The analyzer box is made of soft iron (to reduce the stray magnetic field) and houses the 45-degree parallel plate electrostatic energy analyser and detectors. The CEM-IMS is a modular integrated measurement system capable of recording the measurements by remote control via network. CEM-IMS will be used as a pulse counting module to acquire output pulses of channel electron multipliers of charge exchange neutral particle analyzer. Energy calibration of the neutral particle analyzer has been carried out using plasma discharge based H+ ion source. This paper describes the principle of core-ion temperature estimation and the design, development, and calibration of the Passive Charge Exchange Neutral Particle Analyzer for ADIYA-U tokamak plasma. References: 1. T. A. Santosh Kumar, L. M. Awasthi, C. Chhaya, H. D. Pujara, B. N. Buch, H. R. Prabhakara and S. K. Mattoo, A technical report: Aditya Charge Exchange Diagnostics, IPR/TR-56/96, February 1996.

Speaker: Dr Snehlata Aggarwal (institute for plasma research)

Snehlata Aggarwal FEC 2018_PREPRINT_ABS ID 639.pdf

summary slide_snehlata aggarwal_abs id 639.pdf

343 Design and testing of X-mode reflectometry system for coupling studies of lower hybrid waves in ADITYA-U tokamak

A new passive active multijunction antenna (PAM) has been designed and is in advance stages of fabrication for ADITYA-U tokamak. The PAM antenna has the ability to couple lower hybrid waves (LHW’s) in to the plasmas near cut-off densities. The coupling of LHW’s depends on plasma density and its profile near the mouth of the antenna. To determine these plasma parameters, experimentally, an X-mode reflectometry system has been designed and is under fabrication. The reflectometery system is designed to operate in the frequency range from 26 GHz to 36 GHz and would cover a density range from SOL to 5x1018 m-3 with a toroidal magnetic field between 1 T and 1.5 Tesla. The total frequency band is swept in 100 microsecond to improve density profile reconstruction. The ADITYA reflectometer is built to operate in frequency modulation continuous mode (FW-CM) or at a fix frequency mode for density fluctuation study. The reflectometery consists of two parts, i.e., the transmitter and the receiver. The transmitter mainly consists of microwave source, amplifier, a single sideband modulator (SSBM), frequency multiplier and a horn antenna to launch x-mode in to the plasma. Similarly the receiver consists of horn antenna, amplifier, mixer and de-modulator. In the de-modulator section, a quadratic demodulation (IQ) is used to extract in-phase and quadrature-phase information from the reflected signal. These measurements provides the density profile information. Finally, an ADC with 12 bit resolution will convert the analog signal in to a digital signal which will be processed through a FPGA based data acquisition system. Sectorial E-plane horn antenna is designed using commercial available software for transmitting/receiving microwave signal to/from the plasma and has an input cross-section of 7.112mm x 3.556mm and output cross-section of 7.112mm x 63.64mm. The length of antenna is 120mm. The analysis of the antenna meets our design requirement of high gain (16dB), low insertion loss and low VSWR (1.1). As the sectorial E-plane antenna is placed inside the tokamak, the above mentioned gain is significant. The details of the reflectometry system focusing on the design of sectorial E plane horn antenna, microwave hardware, test result of different microwave components, along with the density profile reconstruction technique will be presented in this paper.

Speaker: Mr Jagabandhu Kumar (InIPR)

summary_slide1.pdf

344 Design of a NIR Spectrometer for Aditya-U Tokamak and Initial Results.

The hydrogen line series is a sensitive diagnostic of detached divertor. Divertor plasma is characterized by low temperature (1-10 eV) and high density (1019~1020 m-3). The three body recombination dominates the divertor region and is highly sensitive to the divertor plasma Te and ne. Based on earlier experiments, NIR (800 nm-2300 nm) spectroscopy system is designed for Aditya-U tokamak since it can be used for machine protection, plasma control and performance evaluation. Three experiments are proposed here. First is the spectral survey for Paschen H line series and low-Z impurity monitoring. The second one is to provide a validated background emission for divertor Thomson scattering experiments wherein blackbody radiation, bremsstrahlung, recombination and impurity lines contribute largely to the background noise. The third is the measurement of Br9/Paα intensity ratio as it is a possible Te sensitive diagnostic. The signal estimation for the Paα line for present plasma parameters has been carried out in the edge region of Aditya-U tokamak. Since the dark current levels of the commercially available detectors in the NIR range is significantly high (10 Ke-/p/s), signal estimation becomes important. Theoretical estimation of the line and bremsstrahlung emission for the Paα line using the atomic data from the ADAS database has been done [2]. These are found to be ~3*108 and 1.5*108 photons cm-2 s-1 for ne= 1*1012 cm-3, Te=15 eV and nn=7*109 cm-3 respectively. The intensity estimates are well above the dark current levels of the detector. In order to observe clearly resolved spectra, the design and selection of the spectroscopic system comprising of the spectrometer, grating, detector and the collection optics plays an important role. This is also discussed in this work. With this system and with proper line of sight collection optics and optimization for maximum throughput, we can provide information on the plasma control, divertor recycling and machine protection. Initial results namely the survey spectrum and the plasma electron density and temperature estimates will be presented for various Aditya-U plasma shots and a comparison with other existing diagnostics will be presented.

Speaker: Dr Payal Pandit (Institute for Plasma Research, Gandhinagar)

345 Development of Multipurpose Soft X-Ray Tomography System for ADITYA-U.

Study of soft x-ray(SXR) radiation emitted during plasma discharge gives valuable informations on magneto hydrodynamic(MHD) activities, e.g. nature of minor and major disruptions, mode structure, magnetic island, plasma shape, plasma position and chord average electron temperature in tokomak. Intensity of SXR radiation depends mainly on electron temperature, plasma density as well as on impurity in plasma; and is routinely measured with SXR photodiode/diode array. SXR tomography is a powerful diagnostic tool that uses line integrated measurements of SXR radiation and reconstruct two dimensional SXR emissivity profile. For this purpose SXR cameras having array of photodiode detectors are required to mount suitably around poloidal plane of the tokamak. Multipurpose SXR tomography (SXRT) system is designed and developed using 16 channel absolute XUV detector array for ADITYA-U to perform above measurements. In this report, discussions are centered on (1) the determination of minimum number of SXR cameras and detectors to reconstruct emissivity profile for m=2 mode structure which plays a major role for total disruption of plasma, (2) Fourier-Bessel expansion techniques used in SXR tomography software for the reconstruction of two dimensional SXR emission profile, (3) SXRT camera design, electronics and data acquisition system, and (4) first results of experimental campaigns in ADITYA-U.

Speaker: Mr Jayesh Raval (Institute for Plasma Research (IPR), Bhat, Gandhinagar, India)

summary_slid_ex_p4_18.pdf

346 Development of shell injection system for the future IFE power plant

A laser-driven inertial fusion energy (IFE) reactor should achieve the fusion of injected fuel pellets, which are continuously delivered into the reaction chamber and engaged by laser beams at 10’s Hz. Using a repetitive, 100-fs ultra-intense laser HAMA[1], we have demonstrated the engagement of 1-Hz-injected flying pellets involving fusion neutron reaction for the first time[2]. To induce the fusion burn, injected fuel pellets should be imploded to reach a high-density states that beyond 1000 times of solid density and an ignition temperature beyond 5 keV. A spherical shell is most reliable target design to achieve such a high-density state which has been confirmed in several inertial confinement fusion (ICF) facilities. We have developed a testbed of shell injection system that delivers a spherical shell of deuterated polystyrene with 500 μm in diameter and 7 μm in thickness. The testbed was placed in a vacuum chamber with pressure below 0.02 MPa. 25 shells are lined up in a horizontal tube and pushed by the horizontal needle to the injection point. The vertical needle dropping speed, which is driven by the free-fall gravity, was carefully tuned not to destroy the shell being stuck each other due to static electricity. We found that shells were distorted by a force of the horizontal needle. When the number of shells exceeded 25, they started to be distorted by the needle force and then lost sphericity to the level less than 88%. The friction of the tube surface is the key of the system. The number of injected shells was also depending on the tip structure of the vertical tube. In the current system, the “cone dip” structure with line contact to the surface of the shell has in the best result for release and injection of the shells resulting injection-success-ratio of 75%. We demonstrate that (i) repetitive shell injection was possible with the needle speed of 28 cm/sec to release the shell one by one without distortion of the shell structures, and (ii) distribution of injected shell after 18 cm free-fall was within 11 mm diameter circle, which is still 10 times larger than that of the bead injection system, and the laser-hit-ratio would be the level of 5%. This specification is enough for the first laser engagement experiment. [1] Y. Mori et al., Nucl. Fusion 53 (2013) 073011. [2] O. Komeda et al., Sci. Reports 3 (2013) 0730113.

Speaker: Prof. Yoshitaka Mori (The Graduate School for the Creation of New Photonics Industries)

20181024_IAEAFEC2018summarySlide.pdf

347 ECRH and mode conversion in overdense W7-X plasmas

Electron Cyclotron Resonance Heating (ECRH) is the main plasma heating mechanism in Wendelstein 7-X (W7-X) Stellarator. It is provided by 10 gyrotrons at 140 GHz (corresponding to the second harmonic cyclotron resonance at 2.5 T) with the power of 1 MW each. The X- and the O-modes were successfully used in a wide range of operation scenarios: X-mode for low and moderate densities (up to the cutoff at $1.2\cdot10^{20} m^{-3}$), and O2-mode for higher densities (up to ~$2\cdot10^{20} m^{-3}$). Possible operation at yet higher densities would involve double mode-conversion from O- to slow X- and to Bernstein-mode, i.e. an OXB-scenario. The physics of O-X conversion is outside of applicability of the routinely used geometrical optics approximation (WKB-theory) and should be considered within a full-wave approach. In this work, the wave physics of O-X conversion in overdense W7-X plasma is investigated. The results are also applicable to the inverse problem of electron Bernstein emission (EBE) diagnostics. The work discusses: (a) Possibilities for the realization of this mode conversion scenario within the capabilities of the existing ECRH system in W7-X; (b) Development of the “optimal” O- to X- conversion scenario within the constraints set by the 3D plasma equilibrium. A feasible heating scenario with >85% efficiency is identified. (c) The effect of turbulence on the conversion efficiency is assessed. For this study, a new 3D, cold plasma full-wave code has been developed. The code utilizes the Finite Difference Time Domain (FDTD) technique. The computational domain is “minimized” around the WKB-trajectory of the reference ray, and is matched to the surrounding plasma by using the so-called “convolutional perfectly matched layers (CPML) boundary condition”. The background magnetic field is recovered from the pre-computed 3D equilibrium data. The code takes advantage of massive parallel computations with Graphics Processing Units (GPUs), which allows for up to 100 times faster calculations than on a single-CPU. This feature allows for efficient parametric optimization studies over a broad range of possible experimental conditions.

Speaker: Dr Pavel Aleynikov (Max-Planck-Institut für Plasmaphysik)

FEC2018_poster.pdf

summary.pdf

348 Edge Current Density Profile Measurement Using an Array of Miniature Magnetic Probes in ADITYA-U Tokamak

Current distribution inside the tokamak needs to be known for understanding of magnetohydrodynamic (MHD) stability and transport. However, the measurement of radial profile of current density is not easy. The external magnetic measurements yield only the plasma shape and global current profile parameters such as βp and li in tokamaks. The radial current density profile is reconstructed using simulations codes such as EFIT incorporating the external magnetic measurements and kinetic profile measurements. The radial profile of current density in the edge and scrape-off-layer (SOL) is measured for ADITYA-U tokamak using a set of miniature magnetic probes which are inserted inside the last closed flux surface (LCFS). These magnetic probes are designed, fabricated, calibrated and installed in ADITYA-U tokamak, a medium sized air core tokamak with a major radius of 0.75 m and a minor radius of 0.25 m. These coils can be translated along the radial direction and rotated along the axis using a multi-motion feedthrough. The linear motion provides the radial profile whereas the rotational motion provides the angular profile of the current density. These miniature coils are housed inside a ceramic assembly for thermal and electrical insulation from the plasma. The coils are adequately calibrated for the frequency response using a test setup before inserting into the tokamak. The current density profile in the edge and SOL region of ADITYA-U tokamak has been successfully measured. The results obtained from the probes will be corroborated by those obtained from an array of miniature Rogowski coils planned to be inserted inside the LCFS. Further, the results are justified by comparison with the measurement of plasma position using a pair of Sine-Cosine Rogowski coils installed in tokamak. The measured profile matches reasonably well with that reconstructed using EFIT code. After thoroughly establishing the measurements, the changes in current density profile in the edge and SOL region due to externally applied radial electric field with biased electrode and during multiple periodic gas puffing have been studied. The details of probe installation and operation along with current density profile modification due to radial electric field application and multiple periodic gas puff application will be presented in this paper.

Speaker: Mr Tanmay Macwan (Institute for Plasma Research)

Summary_TMacwan.pdf

349 Effect of externally applied radial electric field (biased-electrode) on Geodesic Acoustic Modes in SINP tokamak

Geodesic Acoustic modes (GAMs), believed to play an important role in L to H transition in tokamaks, are the high frequency branch of the zonal flows and are characterized by toroidally and poloidally symmetric in potential $\phi$ (n=0, m=0) and toroidally symmetric but poloidally asymmetric in density perturbation (n =0, m=1). The coherent modes in the spectral analysis of floating potential fluctuations measured in the edge plasma region of Saha Institute for Nuclear Physics tokamak (SINP-tokamak) using Langmuir probes are recently identified as geodesic acoustic modes (GAMs) having different characteristics over a wide range of qedge. The mode is radially localised in the edge plasma and have finite radial propagation. These coherent modes are simultaneously observed in density and radial electric field fluctuation spectra as well. The observed mode conclusively exhibits all the characteristics of the continuum GAM in the discharges having qedge values from 3.0 to 6.0 in normal tokamak regime. In this range of qedge, the poloidal and toroidal components of the wave-vector clearly show the $n \sim 0$, $m \sim 0$ structure of the mode and the frequency of the mode, and its variation with qedge matches quite well with that predicted by theory. In the intermediate range of qedge = 2.5 - 3, the mode exhibits the eigenmode GAM like characteristics as the frequency of modes does not depend on the local plasma parameters; however, the structures remained of $ n \sim 0$, $ m\sim 0$ type. Decreasing qedge below 2.5, the mode characteristics change significantly with the poloidal wave number becoming finite. Further, these modes are observed to be affected by the externally applied radial electric fields. The radial electric fields are induced by inserting a biased electrode inside the last closed flux surface of SINP-tokomak plasma. Interestingly, it is observed that the radial electric field affect the frequency and amplitude of GAM modes. Frequency range of the typical Eigen-mode GAM widens, owing to increase in temperature of the plasma due to improved confinement. Amplitude of the mode is observed to increase with bias potential.

Speaker: Mr Lavkesh Lachhvani (Institute for Plasma Research)

Summary_Slide_FEC_SINP_Biased_Electrode.pdf

350 Effect of multiple periodic gas puff on neutral temperature in Aditya – U tokamak

The fuel gas injection(s) in measured quantity during the current flat-top region of Aditya-U tokamak discharges has been observed to modify significantly the edge and scape-off-layer (SOL) plasma properties. The effect of these gas puffs on the neutral temperature and their penetration in the edge and SOL region has been studied by measuring the Hydrogen balmer-emission spectra at 656.28 nmfrom different line of sights in the edge and SOL region in both high and low field regions of Aditya-U. The neutral temperature is estimated from the Doppler broadening of the measured H spectrum by appropriately removing the contribution from the Zeeman splitting of the spectral lines. A computer simulation code has been developed in-house whichgenerates synthetic chord-averaged H emission spectra at different radius of the plasma using the electron temperature, density and the magnetic field strength of that radial location measured with other diagnostics. The code includes all the broadening mechanisms such as Doppler, Zeeman, Stark or pressure broadening for simulating the H emission spectrum along with proper convolution of the instrumental width of the measuring system. Depending on the strength of the magnetic field, the code incorporates 7 Zeeman components in case of normal Zeeman splitting, whereas 48 (18 π and 30 ) components are taken in to account in case of Paschan-Back Zeeman splitting. The simulated spectra are used to obtain true values of neutral temperatures by iteratively fitting them to the measured spectrum from the edge and SOL region of Aditya – U tokamak [1]. Furthermore, the developed code has been used to isolate the cold, warm and hot (charge-exchange) components of the hydrogen atoms from the measured H emission spectra from the edge region of Aditya – U tokamak. References: [1] S. Banerjee, J. Ghosh, R. Manchanda, et al., “Observations of Hα emission profiles in Aditya tokamak”, J. Plasma Fusion Res. Series 9, 29 (2010).

Speaker: Ms Nandini Yadav (Gujarat University)

SummarySlide_Nandini.pptx

351 Electron acceleration in dense plasmas heated by picosecond relativistic laser

Laser light with relativistic intensities and pulse length exceeding picosecond (ps) has been available recently. Fast electrons generated by over-ps laser-matter interactions are found to be enhanced beyond the scaling laws used in the sub-ps regime. Theories for sub-ps interactions cannot be scaled up simply to ps regime due to that meso-scale physics such as ion fluid dynamics and multiple scattering of electrons by intense fields set in. We develop theoretical models for superthermal electron generation in ps relativistic laser-plasma interactions. Relativistic-intensity lasers are capable to push dense plasma and form a sharp interface by the laser hole boring (HB). We find that due to the continuous laser heating in ps time scale, the pressure balance between plasma and laser light is established being assisted by the sheath electric field, which acts as a surface tension, and then, the HB stops [1]. By solving the pressure balance equation, we derive the limit density for the HB, above which the laser light cannot push beyond. After the HB stops, the hot plasma starts to blowout back towards the laser at the interface where electrons interact with the intense laser multiple times stochastically and gain energy. Electron acceleration through multiple scattering by laser is also found in a multi-ps laser interaction with thin foil where fast electrons recirculate around [2]. We here study the electron energy distribution based on the relativistic Fokker-Plank equation in momentum-$p$ space. We introduce new diffusion and friction coefficients that represent the stochastic processes in the laser-foil interaction. The steady solution of the Fokker-Plank equation is found to be a power law when the diffusion coefficient is proportional to $p$. The particle-in-cell simulation shows that the high energy component of the electron distribution becomes a power law during the over-ps interaction. Our finding provides a further insight for complex multi-ps laser plasma interactions. The new electron acceleration mechanisms we studied here are essential for various applications of ps intense lasers, and also important in terms of Laboratory astrophysics being related to the stochastic acceleration of cosmic rays in universe. [1] N. Iwata et al., Nat. Commun. 9:623 doi: 10.1038/s41467-018-02829-5 (2018). [2] N. Iwata et al, Phys. Plasmas 24, 073111 (2017).

Speaker: Dr Natsumi Iwata (Institute of Laser Engineering, Osaka University)

summary-IAEA2018_iwata.pdf

352 Excitation of Electron Temperature Gradient (ETG) Turbulence and Effect on Plasma Transport in LVPD

Understanding electron transport across magnetic field lines in a fusion device is critical. Linear calculations based on numerical and theoretical models reveal that the ETG mode, which is responsible for the turbulence, is a fast growing instability driven by $\nabla T_e$ with growth rate $\gamma_{ETG}\approx\omega_{*T_e}=k_y\rho_e(c_e/L_{T_e})$, when $\eta_e=L_n/L_T$ exceeds a threshold value. Here $c_e$ is the electron thermal velocity and $L_n, L_{Te}$ are the density and temperature gradient scale lengths, respectively[1,2]. ETG is a short wavelength,$k_\perp\rho_e\leq 1 << k_\perp\rho_i$, and low frequency mode, $\omega$ in the range $\Omega_i <\omega<<\Omega_e$, where $k_\perp$ is the perpendicular wave vector, $\rho_r/\Omega_e$ and $\rho_i/\Omega_i$ are the Larmor radii/ gyro frequencies of electrons and ions. Electron gyroscale fluctuations have been reported in National Spherical Torus Experiment[3] and their role have been invoked to explain the plasma transport in Tore Supra[4]. However, all signatures of ETG turbulence could not be obtained due to extremely small wavelength, $\rho_e\sim \mu m$ in the range of $k_\perp\rho_e\sim1$, in high magnetic fields ($\sim20kG$) of tokamaks. Further, tokamaks have complex geometries, which restrict measurement and have limited control over the parameters that govern the turbulence. Basic plasma devices (linear or toroidal), on the other hand, provide a simplified geometry and control of magnetic field, thus brings scale length of turbulence well within the measurable limits. This provide a clear incentive to study ETG in basic plasma devices such as Large Volume Plasma Device(LVPD). However, these devices usually have plasma, which is contaminated by the presence of ionising, hot and non-thermal electrons, a potential sources of instabilities. This renders making a case for ETG difficult. An unambigous observation on electron temperature gradient (ETG) driven turbulence is reported in LVPD. In the Electron Energy Filter(EEF) modified dressed plasma, the observed ETG turbulence in lower hybrid range of frequencies $f=(1-80 kH_z)$ is characterized by a broadband with a power law. The mean wave number, $k_\perp\rho_e=(0.1-0.2)$ satisfies the condition $k_\perp\rho_e\leq1$ [5].

Speaker: Dr LALIT AWASTHI (IPR)

ETG_slide_LMA.pdf

353 Experimental Discharge Characterization of IEC Plasma Device

In this paper, Egyptian first inertial electrostatic confinement fusion (IECF) device, constructed at the Egyptian Atomic Energy Authority (EAEA-IEC), is introduced the characterization of IEC Plasma Device. It consists of 2.8 cm stainless steel cathode, 6.5 cm anode diameter with 10 cm diameter 30 cm height vacuum chamber. The discharge current and voltage of plasma discharge has been recorded using current probe and resistive voltage divider respectively. The X-ray emissions in IEC plasma device were investigated by employing time-resolved detector. The temporal distributions of detected x-rays emission are occurring during the initial 1 microsecond. The calculated rate of DD-neutron generation using the same electrode configuration about 106 – 108 neutrons/second.

Speaker: Prof. Gamal Elaragi (Egyptian Atomic Energy, Cairo, Egypt)

354 Experimental investigation of Power Coupling by RF Antenna into Plasmas in Presence of Magnetized Ions

Capacitive discharges are created in the near field regions of ICRF antennas and thus power coupling by these antennas depend on the sheaths around them. Magnetization of ions in the plasma around these antennas also affects the power coupling into the plasma with major implications in ICRF antenna’s in tokomaks. A capacitive discharge is designed to study power coupling in such plasmas in a linear device. A symmetric capacitively coupled helium discharge is created by three cylindrical electrodes placed at specific axial positions in a linear chamber in presence of axial magnetic fields. Axial magnetic field is strong enough to magnetize helium ions with their cyclotron radius smaller than, the cylindrical electrode radius. In this study, power measurement in conjunction with detail circuit analysis of magnetized capacitive sheaths has been performed to determine the plasma impedance. Plasma impedance can reveal many important aspects of the power coupling into the plasma such as the mode of discharge, power coupling to individual species (ions and electrons) and conditions of electron series resonance all of which are modified extensively in presence of magnetic field. The obtained impedance characteristics along with power measurements are qualitatively discussed to understand the effect of magnetization of ions on the discharge.

Speaker: Mr Jay Joshi (Institute for Plasma Research, India)

355 Fast Wave induced ICRF plasma Expansion in ADITYA torus

In ADITYA tokamak, ICRF plasma is produced by a single strap poloidal antenna located at LFS by exciting 24.8 MHz with a RF power < 80 kW for the purpose of developing Ion Cyclotron Wall Conditioning (ICWC) scenarios. Suitable combination of density (by regulating RF power and fill pressure) and Bt are investigated to allow the Fast Wave (FW) propagation in the torus volume. Initially at high Bt, the ICWC plasma which was previously localized inside the antenna box, is spread along the toroidal field lines. The plasma is radially and poloidally localized only near the antenna location. Below a particular Bt, plasma is expanded into the vessel in radial direction. This expansion of plasma is explained by considering the cold ion dispersion of FWs. It is observed that the Slow Wave branch is non-propagating for the entire Bt range, whereas, FW starts propagating towards HFS at Bt < 0.2 T for the entire plasma volume. This critical Bt reasonably agrees with the experiment. This scenario could be useful in wall conditioning and wall coating in future fusion machines, where plasma uniformity is desirable.

Speaker: Dr Kishore Mishra (Institute for Plasma Research)

SummarySlide_KMishra_FEC_2018.pdf

SummarySlide_KMishra_FEC_2018.pptx

356 Gas Fuelling Control System of Aditya Tokamak

In Tokamak, the “gas fuelling control” plays an important role to produce plasma in different operation phases from plasma current initiation till end. Apart from main gas injection for plasma initiation, several plasma parameters such as density, temperature, and events like recycling, disruption / runaway mitigation etc. are controlled by injecting the fuel gas in different amount and from different locations in the vacuum vessel at different times in the plasma discharge. This requires a programmable, sophisticated and precise gas feed control system for controlling different gas feed valves located on the machine. In Aditya tokamak, a customised gas (feed) fuelling control system has been developed, installed and made operational meeting all the requirements of the plasma operation and control. This control system consists of customised programmable pulse generator, signal condition electronics, power supply, isolation etc. Desirable pulses of designated pulse-widths and amplitudes with designated time delays are generated using LabVIEW [National Instruments] based control panel and fed into the gas-feed valves for gas insertion. This control system is a sub-system of the overall Aditya tokamak central operational system and is properly tagged with central data acquisition. The novelty of this system lies in its capability to control eight different gas feed valves simultaneously with equal precision. The system has three separate and individually controlled gas fuelling modes according to the plasma operational requirements (1) continuous gas-feed mode (2) pulsed pre-fill mode and (3) pulsed/continuous gas puffing mode. Different gas feed valves can be set and operated individually in each of the above modes simultaneously. The pulsed modes can be controlled precisely with a response time < 100 µs. This is achieved by applying a threshold voltage to gas feed valve with proper electrical isolation. As the gas is absolutely required for every plasma discharge, the control system is designed with redundant protection mechanisms against failure to work in harsh tokamak environment. Design, development, testing and operation of gas fuelling control system of Aditya tokamak along with the experimental results of the gas fuelling control during plasma operation of Aditya tokamak is presented in this paper.

Speaker: Mr Narendra Patel (Institute for Plasma Research)

357 Global PIC simulation of RF waves in toroidal geometry

We report on nonlinear PIC simulations of wave-wave and wave particle phenomena relevant for RF heating and current drive schemes in tokamaks. For this we have developed a new nonlinear kinetic simulation model based on the global toroidal code GTC. In this model, the ions are considered as fully kinetic particles obeying the Vlasov equation and the electrons are treated as guiding centers that are evolved by the drift kinetic equation. We have benchmarked this numerical model to verify the linear physics of normal modes, conversion of slow and fast waves and its propagation in the core region of the tokamak using Boozer coordinates. In the nonlinear simulation of ion Bernstein wave (IBW) in a tokamak, parametric decay instability is observed where a large amplitude pump wave decays into an IBW sideband and an ion cyclotron quasi-mode (ICQM). The ICQM induces an ion perpendicular heating, with a heating rate proportional to the pump wave intensity. Finally, in the electromagnetic lower hybrid wave simulation, nonlinear wave trapping of electrons is verified and plasma current is nonlinearly driven in the core region. However, in many experiments, parametric decay instability is usually observed in the scrape-off layer (SOL). We have upgraded GTC to enable global toroidal simulations that couple the core and SOL across the separatrix by using cylindrical coordinates with field-aligned particle-grid interpolations. Using this new tokamak geometry model, we have implemented the fully kinetic particle pusher to capture the high frequency (ion cyclotron frequency and beyond), and the particle dynamics of guiding center associated with the low frequency waves. To verify the new simulation model, we have carried out simulations to study ion orbit loss at the edge of the tokamak plasma with single null magnetic separatrix for DIII-D tokamak. The ion loss conditions are examined as a function of pitch angle for cases both with and without an electric field.

Speaker: Dr Animesh Kuley (Indian Institute of Science Bangalore)

Summary_slide.pdf

358 H-11B Fusion Reactor with Extreme Laser Pulses for non-LTE Igniton

H-11B Fusion Reactor with Extreme Laser Pulses for non-LTE Igniton

Heinrich Hora
Department of Theoretical Physics, University of New South Wales, Sydney/Australia
h.hora@unsw.edu.au

The progress for the design of a reactor for laser boron fusion is following a road map [1] based on the use of extreme deviations from local thermal equilibrium LTE conditions by using just available picosecond laser pulses of more than petawatt PW power. Fusion of hydrogen H with the boron isotope 11 (HB11 fusion) at LTE is extremely difficult. For spherical compression with lasers, densities 100,000 times of the solid state and temperatures above 100 keV are necessary, such that the energy gains are about five orders of magnitudes below the usual DT fusion. The necessary non-LTE ignition condition is possible if the equation of motion is determined by the electric and magnetic fields E and H of the laser such that the gas dynamic pressure is only a small perturbation. The nonlinear (ponderomotive) force calculations of 1978 [2] resulted in ultrahigh accelerations, measured by Sauerbrey [3] as predicted. With the present ps extreme laser pulses, the measured [4] nine orders of magnitudes higher energy gains from HB11 can be explained with inclusion of the avalanche reaction due to the generated three 3 MeV alphas at each reaction [5]. Combining these results with the kilotesla magnetic fields [6] for cylindrical trapping of the reaction in solid density HB11 fuel ignited end-on by the petawatt laser pulse, shows how 14 milligram of boron produces 300 kWh energy in nearly equal energetic 3 MeV alphas. The reported steps for the design of the reactor follows the parameters [1] for energy genertion with no problems of nuclear radiation producing low cost electricity.
[1] Hora H., Eliezer S. Kirchhoff G.J, Nissim N., Wang J.X., Lalousis, P., Xu Y.X., Miley, G.H., Martinez-Val J.-M., McKenzie W., and Kirchhoff, J. 2017 Laser and Particle Beams 35, 730
[2] Hora H., 1981 Physics of Laser Driven Plasmas Wiley New York
[3] Sauerbrey R., 1996 Physics of Plasmas 3, 4712
[4] Picciotto A., Margarone D. et al. 2014 Physical Review X4, 031030
[5] Eliezer S., Hora H., Korn G. et al. 2016 Physics of Plasmas 23, 050704
[6] Fujioka, S. et al. 2013 Nat. Sci. Rep. 3, 1170

Speaker: Prof. Heinrich Hora

359 Impurity Screening in High Density Aditya Tokamak Plasmas

R. Manchanda1, M. B. Chowdhuri1, Nandini Yadava2, J. Ghosh1, 3, S. Banerjee1, Nilam Nimavat, K. Tahiliani, M. V. Gopalakrishna, U. C. Nagora1, P. K. Atrey1, J. Raval1, Y. S. Joisa1,
K. A. Jadeja1, R. L. Tanna1, and Aditya team

1Institute for Plasma Research, Bhat, Gandhinagar 382 428, India
2Gujarat University, Navrangpura, Ahmedabad 380 009, India
3Homi Bhabha National Institute, Mumbai, 400094, India

E-mail : rmanchanda@ipr.res.in

Abstract

Impurity behaviour has been studied for the high density Aditya tokamak plasmas. These discharges were operated with higher toroidal magnetic fields and thereby it sustained higher plasma current. Higher densities were achieved with the help of multiple gas puffs. High energy confinement times, sometimes higher than the values predicated by Neo-Alcator scaling for Ohmically heated tokamak plasma were achieved for these discharges [1]. In Aditya tokamak, visible and VUV spectroscopy have been extensively used to study the impurity behaviour. The neutral hydrogen and impurity emissions were routinely monitored by optical fiber, interference filter and PMT based system in the visible range. The spectral line emissions from higher ionized charge state of impurities, such as C4+, and O5+, were recorded by a VUV survey spectrometer operated in the 10 - 180 nm. This wavelength range covers the important lines of partially ionized low and medium Z impurities, as for example iron and also emissions from higher excited states of highly ionized low Z impurities, like carbon and oxygen. It has been found that H, OII, and CIII emissions normalized with density (ne), and visible continuum normalized with ne2 show a gradual decrease with increase in density indicating lower impurity concentration in the high density discharges. This is also corroborated by the observed reduction in radiation power losses with increase in ne. These results clearly suggest the achievement of improved confinement for Aditya plasma and are correlated with obtained higher energy confinement times in those discharges. In this presentation, details studies on impurity behaviour for its role into the improved plasma properties in these high densities plasma discharges will be discussed.

[1] R. L. Tanna, J. Ghosh et al, Nucl. Fusion 57 (2017) 102008

Speaker: Mrs RANJANA MANCHANDA (INSTITUTE FOR PLASMA RESEARCH)

Summary Slide_ Ranjana_FEC2018.doc

360 Integrated System Electronics and Instrumentation ; Operation and Diagnostic for Aditya-U Tokamak

The first phase operations of Aditya-U successfully performed various plasma experiments with repeatable plasma discharges of maximum plasma current of ~160 kA and discharge duration ~250 ms. The electronics and instrumentation requirement for these experiments are mainly of signal conditioning, embedded digital signal processing and automation. The signal conditioning electronics is developed to measure signal through sensors of different plasma diagnostics. To measure accurately and precisely the signal of nano order in highly radiated (electric and magnetic field) environment of Tokamak, special care has been taken in terms of design, component selection, signal transmission and EMC/EMI shielding. The signal conditioning design incorporates attenuation, amplification, isolation, filtration, self-test and offset calibration. At present Electronic system caters around the need of hundreds of channels from different diagnostics of Aditya-U. These channels include electronics for Electromagnetic, Spectroscopy, Bolometer, Soft-x-ray, Microwave and ECE radiometer diagnostic. FPGA and microcontroller based electronics are designed and developed for plasma operation and control applications. Microcontroller based few real-time feedback control applications were successfully implemented in the last campaigns and these experiments are plasma disruption control using Electrode-Bias and ICR pulse, Radial position control, density feedback control and real-time control of gas-feed pulses to reduce wall loading of fuel gas. FPGA based timing system is developed which generates trigger to operate different subsystems and archive data during plasma discharge of Aditya-U. The Automation & Instrumentation system is developed for baking of vacuum vessel and pumping lines, TF coil temperature measurement and logging for Aditya-U. The LabVIEW based SCADA application monitors and control the temperature of PLC based baking system The paper will describe electronics for plasma diagnostics, Instrumentation, embedded control and timing system for plasma operation.

Speaker: Ms Rachana Rajpal (Institute for Plasma Research)

IAEA Summary EX P4-30.pdf

361 Interpenetration and Stagnation in Collapsing Plasma’s

Future inertial fusion reactors are supposed to work with long pulses or with high repetition rates using repeated pellet implosions. In such extreme environments, the reactor wall materials will be disclosed to short X-ray pulses and fusion generated fragments. This will cause ablation to the wall material in the form of plasma that is expected to collide with each other in the center of the chamber or interpenetrate to elsewhere within the reactor chamber. In this work, a laboratory experimental setup; is devoted to use colliding plasmas scheme to investigate the collision effects similar to plasma facing components in fusion reactors.
Different materials were used for these collapsing plasma experiments for controlling the velocity of plasma plumes. A special experimental setup was built where the laser is focused into a line-like shape impinged as two perpendicular beams onto a semi-circular target. The setup was carefully built to force the seed plasmas to collapse in the center of the chamber prior to the colliding process. The interpenetration and stagnation layer, if exists, of plasmas of candidate fusion wall materials, viz., carbon and tungsten, and other materials, viz., aluminum, and molybdenum were investigated in this study. While tungsten plumes interpenetrate each other at the colliding interface, carbon colliding plumes formed a strong stagnation layer, which could be a source of nanoparticles and plasma aerosols generation that may hinder fusion high repletion rates.

Speaker: Dr Khaled Al-Shboul (Nuclear Engineering Department, Jordan University of Science &amp; Technology)

362 Investigations on Growth of Quasi – Longitudinal (QL) Whistlers with Energy Scaling of Energetic Electrons in LVPD

Whistler waves are driven unstable by the runaway electrons generated in tokamak disruptions with serious consequences on reactor scale tokamaks and by relativistic electrons in space plasmas but with different electron distributions. In LVPD, we report observations on whistlers of Quasi Longitudinal (QL) nature. These are highly oblique in nature and have free energy source asssociated with anisotropic distribution of electrons, beams, loss cones, magnetic mirrors, ring currents, electron temperature anisotropy etc. Presence of large Electron Energy Filter (EEF) in LVPD divides plasma into three distinct regions of Source, EEF and Target plasmas. The source plasma, which is the focus of present investigations, is a region between the plasma source and the EEF. Transverse magnetic field of EEF(B_EEF~160G ) modifies confining axial magnetic field(B_z ~6.2G ) of LVPD and imaculates magnetic mirror configuration. Reflected energetic elctrons from the developed loss cone, results in the first laboratory observation of QL whistlers [1]. This paper will report on experimental observation of QL whistlers from an asymetrically localised, thin rectangular slab in source plasma, populated by energetic electrons. The observed whistlers are electromagnetic in nature and exhibits strong coupling of density with potential and magnetic field fluctuations. The turbulence is broadband in nature with frequency ordering between i.e. in lower hybrid range. The QL mode propagate highly obliquely (≈87°) with its perpendicular and parallel wave numbers as and respectively. These observations are in good agreement with theoretical predictions for reflected electron driven QL whistlers [2-4]. Analytical observations suggest that the growth of the instability has strong dependence on the plasma density and energy of the energetic electrons apart from the population of reflected electrons. Results on growth of instability with energy scaling of reflected energetic electrons will be presented.

Speaker: Mr Amulya Kumar Sanyasi (Institute for Plasma Research)

summary_EX_P4-27.pptx

363 Ka-Band Reflectometer System for measuring Radial Electron Density Profile at IPR.

The determination of electron density and its fluctuations are essential in understanding the physical principles that determine the confinement in tokamaks. Aditya tokamak at IPR is routinely operated with a peak density of ~ 3 x 1019 m-3 and a typical magnetic field of 0.75T. We present and describe the bench test calibration and its results and the designed FMCW Reflectometer which is capable of measuring the electron density profile (ne(r)) in the range (0.84 to 1.98) x 1019 m-3 with minimal access requirements. We assume a parabolic density profile and plot the resultant variation in plasma frequency and thus Ka-band from 26.5 to 40GHz is selected. A Ka-Band Frequency Modulated Continuous Wave (FMCW) Reflectometer has been designed and developed to measure the electron density profile. It is to be operated in O-mode due to its simplicity. The super heterodyne detection scheme in conjunction with quadrature down conversion is used for unambiguous phase determination. To overcome the deleterious effects of plasma density fluctuations, the implemented Reflectometry system is capable of ultra-fast sweep over the entire Ka-Band in 5µs and has high data acquisition rates of 200MSps. The Voltage Controlled Oscillator (VCO) used as the frequency source was linearized by nonlinear tuning voltage as input which resulted in only 5% variation in the output beat frequency. Oversized waveguides in the X band (WR-90) have been used to minimize the waveguide dispersion over the swept frequency range. The complete system is controlled by a master trigger received from the tokamak control room which is fed to a trigger pattern generator which triggers the microwave circuit and the data acquisition system at predetermined times. The reflectometer has been calibrated in lab and in-situ in tokamak hall using a custom coaxial delay line for circuit delay as well as the waveguide delay for a length of 9.6m. The dispersion in delay was found by placing metallic mirrors at different locations and finding the internal circuit delay while the dispersion in waveguide is calculated for rectangular waveguides. Multiple (>25) sweeps were done for each position of the mirror (Fig1a) and the results obtained showed very good repeatability (Fig1b).

Speakers: Mr Janmejay Umeshbhai Buch (Institute for Plasma Research), Dr Surya Kumar Pathak (Institute for Plasma Research)

Summary_Slide.pptx

364 Mass Dependent Impurity Transport Study in ADITYA Tokamak

The investigation of impurities and its transport study in tokomak plasma play a vital role in determining the overall plasma performance. It is important to understand the transport of impurities in tokamak plasmas in order to control impurity inside the plasma and its deleterious consequences affecting overall plasma performance. In Aditya, strong boron like carbon lines are usually seen in visible range due to the interaction of plasma with graphite limiters. A 1.0 m multi-track spectrometer (Czerny–Turner) capable of simultaneous measurements from eight lines of sight has been used for measuring the radial profiles of C+ (657.805 nm, 3s 2S1/2–3p 2P°3/2 and 658.288 nm, 3s 2S1/2–3p 2P°1/2). The carbon transport coefficients are determined by modeling the experimentally measured emissivity profiles of C+, using a one-dimensional empirical impurity transport code, STRAHL . This code has been earlier also used for studying the oxygen impurity transport in Aditya which reveals a higher values of the diffusion coefficient compared with the neo classical values in both the high magnetic field edge region (Dmax inboard∼30 m2s−1) and ( Dmax outboard∼45 m2s−1 ) in the low magnetic field edge region[1]. Similar studies are carried out for neon by injecting neon using neon spectral lines in the UV/visible region at the plasma current flat-top. In this paper, we compared the transport coefficients of all the three impurity species, i.e., carbon, oxygen, neon etc., through the modeling (using STRAHL code) of experimental emissivity profiles recorded in the typical discharges of Aditya tokamak. The transport coefficients for these species are determined by minimizing the residual error between the measured and calculated emission profiles for all the three species. By comparing the diffusion coefficient of three species, understanding the mass dependency of impurity transport has been attempted in Aditya tokamak. References: [1] M.B. Chowdhuri et al 2013 Nucl. Fusion 53 023006.

Speaker: Mrs sapna Mishra (ITER-India,Institute for plasma research)

365 Mechanical Mockup of IFE Reactor Intended for the Development of Cryogenic Targets Mass Production and Rep-Rate Delivery into the Reaction Chamber

A vital goal of inertial fusion energy (IFE) research is development of high-precision, mass production technologies for cryogenic fuel targets fabrication and their delivery to the reaction chamber at a high rate (10-20 Hz) [1]. At the Lebedev Physical Institute (LPI), a mechanical mockup of IFE reactor has been proposed [2] for developing the reactor-scaled technologies that are applicable to mass production of the cryogenic targets and their high-rep-rate delivery. The report presents an overview of the researches underlying this approach, including: - Target mass production. Free-standing cryogenic target production using the FST-technology developed at LPI was demonstrated for cryogenic targets of 1-to-2 mm-diam. with fuel layer up to 100 um-thick. - Target rep-rate delivery. A system for high-rep-rate assembly of the sabot and target (sabot is the target carrier during its acceleration). The report discusses the results, both theoretical and experimental, on modeling a friction-free electro-magnetic acceleration of the levitating assembly "HTSC-Sabot + Target", where HTSCs are the high temperature superconductors. - Injected target on-line tracking. The results of computer experiments on Fourier holography for application to injected target on-line diagnostics and tracking are presented. - Target protection. A system proposed for multiple target protection methods is based on the following principles: 1. Formation of the cryogenic layer with an isotropic ultrafine fuel structure to reduce the layer sensitivity to the external thermal and mechanical loads. 2. Use of friction-free delivery of the "HTSC-Sabot + Target" assembly to reduce the heat flux on the target. 3. Use of conical supports for a target nest in the sabot to reduce the mechanical loads arising during acceleration of the "HTSC-Sabot + Target" assembly. 4. Use of outer coatings (cryogenic, metal) in the target design to reduce risks of cryogenic layer damage as a result of target heating by thermal radiation of the hot chamber walls. 5. Co-injection of a target and a protective cover from freezing gases (D2, Xe) to reduce risks of cryogenic layer damage as a result of target heating by hot residual gases in the reaction chamber. This work was supported by the RF State Task of the Lebedev Physical Institute, by the International Atomic Energy Agency.

Speaker: Prof. Boris Kuteev (National Reserch Center Kurchatov Institute)

366 Mode Converted Electrostatic Nonlinear Ion-Ion Hybrid Mode In Tokamak Plasma

Mode conversion (MC) process proves to be of prime importance in fusion as well as in magnetospheric plasma [1,2,3]. However, the presence of multiple ion species, even with small concentrations, can lead to the appearance of new and modified resonance, cutoff, and crossover frequencies [4]. Nonlinear effects such as pump self induced filamentation and parametric decays further complicate the MC physics ans associated heating processes [5,6,7,8]. It is generally seen that intense localized electric fields of the soliton form are generated due to the density changes (density cavities) caused by the dominant ponderomotive forces acting on the charged species. It turns out that the nonlinear fate of the mode converted electrostatic wave beyond the MC layer is still an open question. With this motivation, we investigate such a nonlinear state of the mode converted electrostatic ion-ion hybrid wave in the vicinity of the MC layer. In context with it, an exact nonlinear solution of the ion-ion hybrid mode is estimated under the influence of adiabatic perturbations in a Two ion species magnetized plasma. The dominant nonlinearity arises through the ion ponderomotive force term thereby modulating the plasma density profile. The nonlinear equation which has KorteVeg De Vries [KdV] soliton as its solution, represents the nonlinear stage of a purely growing mode. It turns out that these solitons exists only if the wave frequency is lower than the Buschbaum frequency and if the concentration of the lighter ions is less than the heavier one. The resultant ponderomotive expulsion of plasma is discussed in terms of intense localized electric fields and associated density cavities. The application of the theoretical model is discussed in terms of Proton and Tritium minority concentration ratios in Deuterium plasma. References: 1. Wesson, J. (2004). Tokamaks, chapter 5. 2. Kazakov,et al (2010). PPCF, 52(11), 115006. 3. Kazakov, et al (2013). PRL, 111(12), 125002. 4. Buchsbaum, S. J.(1960). PRL 5.11, 495. . 5. G. Morales, et al.(1975). PRL 35 (14) 930. 6. Tagare, S. G., et al(1982). PoF (1958-1988) 25.11. 2012-2018. 7. Toida, M.,et al (2007). JPSJ, 76(10), 104502-104502. 8. Toida, M., et al. (2011). PoP, 18(6), 062303.

Speaker: Dr JYOTI ATUL (INSTITUTE FOR PLASMA RESEARCH, GANDHINAGAR, INDIA)

summary slide j k atul.ppt

367 Modelling of electron cyclotron resonance heating and current drive in the T-15-MD tokamak with GENRAY and CQL3D codes

The T-15-MD tokamak is planned as a normal magnetic-coil tokamak with a flexible ITER-like configuration of the poloidal magnetic field. The main goal of the tokamak T-15-MD is the achievement of long pulse, non-inductive current drive regimes for a high-aspect-ratio divertor plasma configurations. The simulations of the ECRH and ECCD in T-15-MD tokamak are carried out with the ray-tracing code GENRAY and the kinetic Fokker—Planck code CQL3D for two formerly predicted regimes of tokamak operation, namely hybrid scenario with 12 MW auxiliary heating and 2 MA total plasma current, including inductive (Ohmic) current, and the steady-state scenario with 18 MW auxiliary heating and 1 MA fully non-inductive current. The results for 2D distribution of the ECRH power density and ECCD efficiency in the tokamak poloidal cross-section on the flat-top stage of discharge are presented for various injections angles and EC wave modes. It is shown that for the ECCD in the hybrid scenario the injection of the Х2-wave from the LFS is more effective than injection of the Х1-wave from the HFS.

Speaker: Mr Pavel Minashin (NRC "Kurchatov Institute")

368 Neon Gas Seeded Radiative Improved Mode in Aditya-U Tokamak

Neon impurity injection into the tokamak plasma has been found to improve the plasma confinement, known as Radiative Improved (RI) mode in many tokamaks. It is believed that improved confinement in the RI mode is mostly based on the reduction of growth characteristics of the toroidal ion temperature gradient (ITG) mode due to the increase of Zeff and also because of the suppression of turbulence due to increase of ExB shear rotation in the impurity injected plasma. During the last phase of operation of Aditya tokamak neon gas was puffed at the plasma current flattop region to obtain RI mode [1]. In that experiment, the time for the gas puff to start, time gap between gas puffs, number of gas puffs, amount of gas injection by varying pulse width and voltage level in the gas fuelling system were varied. It was found that line average electron density, ne and central electron temperature were increased after the neon puff. Substantial change in plasma edge properties was observed with the increase of radiation and reduction of hydrogen recycling, which led to better particle confinement. The energy confinement time, tau_e, is increased by a factor of 2 from 6.3 to 12.5 ms. This is almost same to the H-mode scaling law of ITER93 ELM-free and 1.4 times the Neo-Alcator scaling for Ohmically heated tokamak plasma. In Aditya-U tokamak, experiment with neon gas puff was carried out to obtain the RI mode and understand the physical mechanism. Along with various similar results obtained earlier in Aditya, many interesting outcomes observed during the experiments in Aditya-U tokamak will be reported in this presentation. [1] R. L. Tanna et al, Nucl. Fusion 57 102008 2017.

Speaker: Dr Malay Bikas Chowdhuri (Institute for Plasma Research)

summary_slide_FEC_2018.doc

369 Observations of Intrinsic Toroidal Rotation using X-Ray Crystal Spectrometer in ADITYA-U Tokamak

A soft X-ray Crystal spectrometer has been developed to measure toroidal rotation velocity and ion temperature in the core of ADITYA-U Tokamak [1, 2] using Doppler shift and Doppler broadening of helium like argon emission in the x-ray region respectively. The spectrometer uses cylindrically bent Si (111) crystal and two dimension CCD detector to measure resonance spectral line of Ar XVII (1S2 1S0 – 1S 2P 1P1) and satellite lines in the wavelength region of 3.94 Å-4.0 Å, viewing the plasma tangentially at an angle of 26˚ with respect to the toroidal direction in the magnetic axis. Central electron temperature is measured through line ratios and compared with other diagnostics. Neoclassical toroidal rotation has been calculated using theory and compared with observations from the experiment. The effect of variation in edge plasma parameters on the core plasma rotation has also been studied. Detailed discussion on the first results is presented in the paper.

Speaker: Ms KAJAL SHAH (PANDIT DEENDAYAL PETROLEUM UNIVERSITY)

Summary_kajal.pptx

370 Particle Simulation Studies on Ion Effective Heating through Merging Plasmas

The merging of spherical tokamaks (STs) attract the attention as a candidate of future fusion reactors. In plasma merging experiments of STs, through magnetic reconnection, two torus plasmas are merged into a single torus plasmas with higher beta. In experiments, it is reported that electrons are significantly heated in the vicinity of the X-point, while ions are mainly heated in the downstream [1]. The comprehension of the heating mechanism can lead to the higher-performance for realizing economical ST reactors. In this paper, we show a new mechanism of ion heating. We investigate the ion heating mechanism by means of particle simulations, which mimic merging plasmas in a ST. Plasmas are pushed by the driving electric field imposed at the upstream boundary in order to express pushed plasmas by the poloidal field coil current in experiments. The initial condition is one-dimensional equilibrium with a uniform toroidal (guide) magnetic field. Our simulations demonstrate that the ion temperature perpendicular to the magnetic field grows mainly in the downstream as in experiments. It is further found that ring-like velocity distributions are formed at local points in the downstream. That is, ions are effectively heated [2]. The formation process of the ring-like distribution is as follows. Ions behave as nonadiabatic upon crossing the separatrix, since the period of time during which they pass through the separatrix is shorter than the gyroperiod. The entry speed of the ions is much less than the outflow speed. The ions rotate around the toroidal magnetic field while ExB drifting in the downstream. The ion orbit in the velocity space is a circle. The ring-like velocity distribution is formed by such ions with different phases of the gyromotion. It is found that the profile of the ion temperature by our simulation fits well to that by a TS-3 experiment [1]. Furthermore, the dependence of the ion temperature on the toroidal magnetic field is investigated. Our simulations show that the ion temperature decreases as the toroidal field is stronger, but the dependence becomes small for the high toroidal field. This tendency is consistent with that in TS-3 experiments [3]. References [1]Y. Ono et al., Plasma Phys. Control. Fusion 54 (2012) 124039. [2]S. Usami et al., Phys. Plasmas 24 (2017) 092101. [3]Y. Ono et al., Phys. Plasmas 18 (2011) 111213.

Speaker: Dr Shunsuke Usami (National Institute for Fusion Science)

summary_slide.pptx

371 Plasma Column Position Measurements using Magnetic Diagnostics in ADITYA-U Tokamak

In a tokamak, for real-time control of plasma column movement, both horizontal and vertical, accurate measurements of plasma column location is compulsory. Magnetic pick-up coils, measuring induced voltage due to change in flux–linkage to them, are widely used of the measurement of temporal evolution of plasma column position in a tokamak. Although measurements of induced voltages are relatively easy, estimation of plasma column position from these measurements are not very straightforward and requires accurate calibration of the coils and huge amount of modeling. In order to measure the plasma column position accurately in ADITYA-U tokamak, several types of magnetic probes are introduced. They include, Mirnov coils, external pick-up coils, Sine-Cosine coils and flux loops. To have a proper calibration factor for these probes, which is a necessity for overcoming geometrical imperfections, discrepancies introduced during installations as well as error magnetic fields from eddy currents in vacuum vessel, an in-situ calibration experiment has been carried out. A time varying current has been passed through a rigid copper conductor placed at different radial and vertical locations inside the vacuum vessel. Induced voltages in all the magnetic probes are recorded due to the different temporal profiles of driven current in the conductor. In addition to that, the magnetic pick-ups by these probes due to different poloidal magnetic field coils, which are operated during plasma operations, has also been measured by driving current through those coils in absence of plasma. Based on these observations several numerical codes have been developed which analyse the raw data from these magnetic probes during plasma shots. After removing all the unwanted flux-linkages to the probes due to vessel eddies and other set of magnetic coils used for plasma operation, the temporal evolution of plasma column's horizontal and vertical movement has been estimated in real time. The plasma column position measured with these probes matches fairly well with other diagnostics, such as, edge Langmuir probes, fast camera images etc. Finally the real time measurements of position movement of plasma column during the plasma discharges have fed onto the plasma position control system for real time control of plasma position in ADITYA-U tokamak.

Speaker: Mr Suman Aich (Scientific officer C)

FEC_Summary_EX_P4_31.pptx

372 Plasma Potential Measurements in the edge region of ADITYA – U Tokamak using Reciprocating Laser Heated Emissive Probes

Laser Heated Emissive Probes (LHEP) have several advantages over conventional filament emissive probes and serve as a tool for direct measurement of plasma potential. Measurement of plasma potential or Electric fields component perpendicular to magnetic field are necessary for fundamental understanding of plasma parameters, transport mechanisms, space charge distribution in plasmas. Owing to complexities of tokamak geometries and high temperature magnetically confined environment, very few attempts have been made for using emissive probes on such complex devices. Here we present a novel design of the LHEP for ADITYA – U tokamak involving radially movable probe shaft with dual probe tip provision made up of LaB6. CW CO2 laser at 10.6 µm having a maximum power of 55 watt is continuously focused on probe tip, using a specialized force air-cooled fiber, despite the radial movement. The set-up is designed for direct measurement of radial profiles of plasma potential in edge plasma region of ADITYA-U tokamak. Probe is biased with respect to plasma potential and I-V is acquired with high sampling frequency. Obtained I-V is plotted and explored for the estimation of ion density, electron temperature and plasma potential. Experimental results are reported here and discussed.

Speaker: Ms Abha Kanik (Research Scholar)

FEC_2018.pptx

373 Progress of a DPSSL based R&D facility TERU for IFE technology and industrial applications

In the most recent study of inertial confinement fusion, the integration experiments to demonstrate ignition burn are planned using kilojoule to megajoule class laser beam lines in the world. These experiments are based on the “single-shot” experiment of which repetition rate is several-shots per day due to limitations of laser cooling time. A dozen shots every second are required to realize the inertial fusion energy (IFE) power plant. We focus on the development of high-energy and high-repetition-rate laser system to assess a continuous supply system of fuel pellets, a control system of the laser injection, and a feedback system linked with radiation measurements. Since 2010, we have initiated a construction of a 100-Joule class diode-pumped solid-state laser (DPSSL) based facility “TERU” (Trek on fusion Energy Roadmap toward Utopia) for research and development on component technologies and related industrial applications. TERU is the first laser facility for IFE research based on 100 J class DPSSL. Status of the current DPSSL is 50 J at 0.5 Hz. The laser amplifier head was designed to evaluate a high gain with high energy storage in the cryogenically cooled Yb:YAG ceramics. A small-signal-gain (SSG) of the Yb:YAG ceramics amplifier pumped by 400 kW has reached 20 with stored energy of 148 J at cooling temperature of 100 K. This is the highest SSG of the cryogenically cooled Yb:YAG ceramics amplifier storing energy over 100 J. This result becomes a benchmark of the high gain with stored energy performance to design the next kilo-joule-class cryogenically cooled Yb:YAG ceramics amplifier. We also start the laser irradiation experiment to explore the fundamental physics of implosion processes, e.g. plane target acceleration, which could replicate the implosion in laser fusion. In our preliminary experiment, a velocity of the aluminum plane target (a thickness of 20 m) accelerated with 2.0×1012 W/cm2 laser irradiation was observed by VISAR measurement. The acceleration velocity reached 560 m/s. The acceleration velocity changing target thicknesses is stored as a database with repetitive laser irradiation. Such database will be useful for the target design and benchmark of hydrodynamics codes.

Speaker: Dr Takeshi Watari (Central Research Laboratory, Hamamatsu Photonics K.K.)

IAEA2018_watari_summaryslide.pptx

374 Radiation power loss study during gas puff induced disruptions in Aditya-U Tokamak

Understanding the density limit in a tokamak is very crucial for projecting the fusion grade tokamak machine. An important role in the disruptions for density limit is played by magneto-hydrodynamic (MHD) instabilities associated with the steepening of the current density profile due to the current channel contraction. This shrinkage in the current channel due to increasing densities is related to the plasma edge cooling induced by influx of particles. Thus the disruption associated with density limit not only depends on the magneto-hydrodynamic (MHD) physics, but also seems to involve transport and atomic processes as well. The gas puff experiments are carried out in a tokamak to understand the physics of plasma disruptions. We report here the study of radiation power loss in disruptive discharges. In Aditya tokamak, multiple pulses of hydrogen gas were injected during the current flattop in the plasma discharge. The gas puff lead to an increase of 20-80 % in central plasma density and many fold increase in the radiation power loss from the plasma edge [1]. The nature and distribution of radiation power loss was distinguishable in disruptive discharges and those discharges that had improved confinement [2], some of which were due to the edge cooling induced fluctuation suppression [3]. Similar experiments are carried out in Aditya-U tokamak with various gases, in which along with further establishment of the results obtained in Aditya with thorough data analysis, many interesting outcomes observed during the experiments in Aditya-U will be reported in this presentation.

Speaker: Mrs Kumudni Tahiliani (Institute for Plasma Research, India)

summary_slide_FEC.pdf

375 Runaway Electron (RE) Mitigation Using Supersonic Molecular Beam Injection in the Aditya-U Tokamak

In fusion devices, runaway electrons (REs) with energies >=10 MeV, generated predominantly during plasma disruptions, can penetrate through the low-Z first wall and melt the interface of actively cooled parts. Majority of disruptions display MHD modes, as precursors. Radiation cool-off at the edge is seen to trigger abrupt growth of MHD modes, mode locking and thereby disruptions. The REs are generated due to increase in plasma resistivity following the thermal quench (TQ). REs pose severe threat to the lifetime of the first wall components and increase the machine down time substantially. Hence, mitigation of REs are a must for successful operation. Several RE mitigation techniques have been tried out in different machines, such as massive gas injection, and resonant magnetic perturbations. However, the effect of both these mechanisms are restricted to the very edge of the tokamak and REs primarily generated inside the plasma following the TQ, are not completely affected by these techniques. Enhancing magnetic fluctuations during disruptions is an alternate method and a more penetrative fueling technique is required to achieve that. Significant RE flux has been found to suppress the magnetic fluctuations and considerable RE current is generated during the disruptions. There is a recent experimental observation of suppression of the RE current during disruptions by the magnetic perturbations, excited by the supersonic molecular beam injection (SMBI). However, a detailed understanding of the underlying dynamics of such a suppression is far from being completely understood. The present campaign on Aditya-U explores such a phenomenon over a wide range of experimental parameters. An SMBI system has been installed on the low field side with a Laval nozzle of throat diameter 0.5 mm and a fast response solenoid valve. The plenum gas pressure can be varied to adjust the speed/penetration of the beam. A particle flux of 2.6E22 particles/s is achievable at a plenum pressure of 1 MPa. Volume hard X-rays are monitored along a central chord and suitable SMBI is launched based on the spatial location of the REs to mitigate them in real time. Interaction of SMBI with REs and magnetic fluctuations will be reported. Finally, a 1D code to study the transport dynamics during SMBI has been developed and simulation results in support of the experiments will also be presented.

Speaker: Dr Santanu Banerjee (Institute for Plasma Research)

Summary_slide_Santanu_Banerjee.pdf

376 Simulations on the particle and heat fluxes for the RF heating H-mode on EAST

In order to understand and control the heat flux issue for the future tokamaks, the particle and heat fluxes of the EAST RF heating H-mode have been simulated by the 6-field 2-fluid model in BOUT++ framework [1]. The simulated particle fluxes induced by the edge coherent turbulence on the outer divertor targets are comparable with the measurements of the width and peak amplitudes by the divertor probes. Based on this simulation, the EAST ELMy H-mode discharges with different plasma current Ip and geometries are applied to study the scaling law of SOL width. The Eich’s Scaling is well reproduced by the simulations [2]. However, the simulated SOL width is only half of the EAST measurements, because there is no RF heating scheme in the simulations, which is effective to change the boundary topology and increases the flux expansion [3]. In order to prove the topology change effects of LHW in SOL region, a modeled helical current filament (HCF) in SOL, which has the same amplitude to the experiments, is added as the force-free form into the 6-field 2-fluid module. The RF sheath boundary condition is also considered in the self-consistent calculation of the radial electric field. The radial magnetic field induced by this HCF could be much smaller than the perturbed field, but it is able to force the perturbations with the same toroidal mode number to grow up at the start of the linear phase. This forced mode is effective to compete with the spontaneous fluctuations and change the linear properties, which leads to the obvious suppression of the divertor heat flux and the broadening of SOL width. The preliminary results shows that the HCF is able to increase the SOL width by ~25%, and the peak parallel heat flux towards divertor target is decreased by 32%. The broadening of the particle flux by HCF clearly shows the secondary striate filaments on divertor target, which is similar to the splitting of the strike point found by the divertor probes. [1] T.Y. Xia & X.Q. Xu, Nucl. Fusion 55 (2015) 113030 [2] T.Y. Xia et al., Nucl. Fusion 57 (2017) 116016 [3] Y.F. Liang et al., PRL 110, (2013) 235002.

Speaker: Mr Tianyang XIa (Institute of Plasma Physics, Chinese Academy of Sciences)

material_xiaty.pdf

377 Study of Iron Impurity Behavior using VUV Spectroscopy in Aditya and Aditya-U Tokamak

Studies of medium and high Z impurities behavior in high temperature tokamak plasmas have become important considering molybdenum, tungsten are being considered as the first wall materials due to its high melting points and capabilities to handle high heat load. These impurity ions are present due to mainly sputtering processes involving plasma facing components in contact with the edge plasma. Presence of such spectrum of impurities leads to enhanced energy loss, fuel dilution and overall degradation of plasma properties. Thus the study of the behavior of impurities is carried out in Aditya and Aditya–U tokamak. VUV spectra from impurities is regularly monitored using a absolutely calibrated VUV survey spectrometer having operation in the spectral range of 10-180 nm, which covers the important lines of partially ionized low and medium-Z impurities and also emissions from higher excited states of highly ionized low-Z impurities. Absolute intensity calibration of this system has been carried out using branching ratio and by simulating the VUV spectra and then comparing those with experimental counts. VUV spectral lines at 28.41 nm (3p6 3s2 1S0 - 3s 3p 1P1) from Fe14+ and, 33.54 nm (2p6 3s2 2S1/2 - 2p6 3p 2P3/2) and 36.08 nm (2p6 3s2 2S1/2 - 2p6 3p 2P1/2) from Fe15+ are measured during the current flat-top region of Aditya and Aditya-U tokamak plasmas. The behavior of iron emission has been studied with respect to plasma parameters and its measured penetration into the plasma has been compared with simulated spectral emissions by taking the impurity transport and relevant atomic data generated using ADAS database.

Speaker: Mr Sharvil Patel (Birla Institute of Technology, Jaipur Campus , India)

Sharvil_FEC_2018_Summary.pptx

378 Target Design Study of Fast Ignition for Ignition and Burning Experiments

In the fast ignition of laser fusion, a reliable target design is required for an ignition scale target. This paper shows the first optimized target design of an implosion phase of the fast ignition, which is scalable to larger targets. The fast ignition scheme can be divided into three processes mainly; the formation of highly compressed fuel core plasma, the generation of high-energy electrons by an intense short pulse laser, and the heating fuel core by the high energy electrons. In the first process, a high areal density fuel core should be formed to stop the high-energy electrons. For the demonstration of a self-ignition the areal density should be more than 1.1 g/cm$^2$. For the self-ignition and high gain target designs it is necessary to carry out many implosion simulations for the large targets which require large amount of computer resources. We conducted 2-D implosion simulation of DT solid spherical target with gold cone target using the optimized laser pulse shape. Finally, we estimated the requirement of the implosion laser energy on the basis of the hydro-dynamic similarity rule. In conclusion, a target can be highly compressed using multi-step laser pulse irradiation to a solid spherical target. In the FIREX-I scale implosion (6.25 kJ/0.35 $\mu$m), the maximum areal density of DT fuel ($\rho R_{max}$) reaches 0.28 g/cm$^2$ with a gold guiding-cone according to two-dimensional simulation. Based on the hydrodynamic similarity, we estimate that the requirement of implosion laser energy for ignition scale target ($\rho R_{max}$ =1.1 g/cm$^2$) is 380 kJ. In order to optimize the whole process of fast ignition, heating simulation is necessary in the next step. This highly compressed fuel core profiles at the maximum $\rho R$ time will be the initial conditions of kinetic simulations for the next processes, where generation of energetic electrons due to the nonlinear relativistic laser plasma interaction, transport and absorption of the energetic electrons processes will be simulated. External magnetic field [5] is effective for improving the heating efficiency because it reduce the divergence angle of the energetic electrons. It will be taken account in next design study.

Speaker: Mr Hideo Nagatomo (Osaka University)

Nagatomo_summary.pdf

379 The impact of the hydrogen species on the HHFW performance with possible new NSTX-U scenarios

The main goal of the NSTX-U is to operate at B=1T. With this magnetic field, the 1st and 2nd harmonics of hydrogen (H) are located at the high-field side and in the core plasma, respectively. As a consequence, part of the high-harmonic fast-wave (HHFW) injected power can be absorbed by the H population. This condition might open up new HHFW scenarios, which in turn can be relevant for the initial ITER ICRH experiments. Therefore, it is important to investigate the impact of the H species on HHFW performance in NSTX-U plasmas. First of all, the injected power absorbed by the H species can affect the electron and/or the fast-ion heating with respect to the “standard” HHFW performance in NSTX. Second, the presence of the H species might have some positive effects: the presence of the 2nd cyclotron harmonic of hydrogen in the core plasma can cause a localized H power absorption, which in turn might modify the ion temperature. On the other side, due to the high-energy (non-Maxwellian) tail of the H distribution function (caused by the acceleration of H species by HHFW), part of the H absorbed power could transfer to electron heating via collisions, providing an additional core electron heating to the “standard” HHFW performance. In this work, we analyze in detail all these possible scenarios by the use of the full wave code AORSA combined with the Fokker-Planck code CQL3D. Initial AORSA simulations have been performed for NSTX-U B=1T plasma with different H concentrations (from 2% to 10%) with and without NBI. For f=30MHz and B=1T, unlike an on-axis power deposition for electrons and fast ions, a localized H absorption around the 2nd cyclotron H harmonic is observed by AORSA. For larger n_phi the electron damping is dominant. However, for n_phi=5 and 10% H concentration, up to 30% and 60% of the total power can be absorbed by H with and without NBI, respectively. A more comprehensive numerical analysis will be presented including also the non-Maxwellian effects in the H and fast ions species by making use of the Fokker-Planck code CQL3D. Furthermore, a magnetic field scan will be performed in order to cover all possible scenarios. H majority plasma will be also considered and compared with D plasma. Finally, the case of 15MHz wave frequency will also be explored because it would open up the possibility to try ICRH minority heating in NSTX-U with B=1T.

Speaker: Dr Nicola Bertelli (Princeton Plasma Physics Laboratory)

Bertelli_summary_slide_IAEA2018.pdf

380 Theoretical and Computational Studies on the Scattering of Radio Frequency Waves by Fluctuations

The practical and economic viability of tokamak fusion reactors depends, in a significant way, on the efficiency of radio frequency (RF) waves to deliver energy and momentum to the plasma in the core of the reactor. Among the various attributes of RF waves is their ability to heat magnetically confined plasmas, induce plasma currents in an effort to achieve steady state, and modify the current profile so as to control plasma instabilities like the neoclassical tearing modes. The RF electromagnetic waves, excited by antenna structures placed near the wall of a tokamak, have to propagate through the turbulent plasma in the scrape-off layer (SOL) along their path to the core plasma. While the propagation and damping of RF waves in the core is reasonably well understood, the same is not true for RF wave propagation through the SOL. In present day fusion devices, the radial width of the SOL is of the order of a few centimeters. In ITER and in future fusion reactors this width will be of the order of tens of centimeters. Any deleterious effects on RF waves due to plasma turbulence in the SOL could impact the efficient delivery of RF energy and momentum into the core. This paper is on a multi-pronged approach towards quantifying the effect of SOL plasma on RF waves. The SOL is composed of coherent filamentary structures and incoherent fluctuations. For coherent structures, a full-wave theoretical model has been developed and is used to benchmark computational codes. These codes are subsequently used to study the effect of a general distribution of filaments. For incoherent fluctuations, the theoretical modeling makes use of the Kirchhoff technique. This technique is based on physical optics and the wave fields at any point on a spatially varying surface are approximated to be the same as the fields on a tangent plane at that point. The results from the theoretical analysis are compared with full-wave numerical simulations for incoherent fluctuations. The final part of these studies is to construct the effective permittivity of a turbulent plasma that is a mix of coherent and incoherent fluctuations. Towards this end, the ``effective medium approximation'' is used to construct the permittivity of the plasma that will be used in full-wave studies of scattering. This cumulative research reveals new and important physical insights into the scattering of RF waves.

Speaker: Dr Abhay Ram (Massachusetts Institute of Technology)

16:10 Coffee Break

EX/4-TH/2 H-Mode & Pedestal

381 A gyrokinetic discovery of fast L-H bifurcation physics in a realistic, diverted, tokamak edge geometry

Despite over 30 years of routine H-mode operation in all the major tokamaks, there has not been a fundamental understanding at the kinetic level on how the H-mode turbulence bifurcation occurs. This is a concern over ITER’s achievability of the H-mode operation with available heating power when the ∇𝑝-driven neoclassical ExB shearing rate is expected to be weak due to smallness of ρ*=ρi/a. The answer to this concern relies on a more fundamental physics question: Will a neoclassically- driven mean ExB shearing (∇𝑝-driven or X-point orbit-loss driven) be essential for the L-H turbulence bifurcation, besides the Reynolds-force driven ExB shearing? Experimental observations appear to diverge on the cause and dynamics of L-H bifurcation. From the edge gyrokinetic code XGC1, we find that a neoclassical-driven ExB-shearing is essential to quench the turbulence irreversibly, and works together with the Reynolds-stress driven ExB-shearing. New XGC1 study also shows that, in ITER, the weak ∇𝑝-driven ExB shearing can be compensated by the X-point orbit-loss driven ExB-shearing and toroidal flow if the edge Ti is high enough. The physics found in the XGC1 simulations reconciles a few different L-H bifurcation dynamics observed in experiments: They are not mutually exclusive but can work together, depending upon plasma conditions. These different mechanisms include not only the source of the sheared ExB flow (turbulent or neoclassical), but also the role of different shearing physics: 1) shearing of the turbulence eddies to smaller structure and higher frequency, leading to dissipation at high wave numbers, or 2) quenching of the turbulence via an eddy tilting-stretching-absorption process via Reynolds work through a conservative absorption process from the turbulence kinetic energy to the plasma ExB flow energy. It is also observed that both ion and electron directional modes are involved in the bifurcation process, with a highly different dynamics from each other. Both modes exist before the bifurcation. The electron modes disappear immediately during the bifurcation process, but the ion modes remain until the end of the bifurcation process undergoing the dissipative ExB shearing action. Experimental observations of two directional modes exist just before the bifurcation process starts.

Speaker: Dr Seung-Hoe Ku (Princeton Plasma Physics Laboratory)

Ku.S-TH2-1_summary.pptx

Ku_TH2_1.pptx

382 Implications of JET-ILW L-H Transition Studies for ITER

Unraveling the conditions that permit access to H-mode continues to be an unresolved physics issue for tokamaks, and accurate extrapolations are important for planning ITER operations and DEMO design constraints. Experiments have been performed in JET, with the ITER-like W/Be wall, to increase the confidence of predictions for the L-H transition power threshold in ITER. These studies have broadly confirmed established dependencies of $P_{LH}$, reduced uncertainties in extrapolations, and highlighted the largest remaining sources of uncertainty. We have also obtained unexpected results with direct relevance for lowering $P_{LH}$ during the non-active phase of ITER operation. A database has been compiled of JET-ILW $P_{LH}$ measurements spanning a range of plasma magnetic geometries, density and toroidal magnetic field values, hydrogen isotopes, ion species mixtures, effects from impurity seeding, and differences in heating and momentum sources. Regression analysis of the database shows in comparison to past scaling studies and to JET-C results, $P_{LH}$ is lower for matched density and magnetic field; however, the exponents for density and magnetic field are larger, resulting in possibly reduced threshold at low magnetic field operation in ITER, but increased values at full field operation. The single largest uncertainty in extrapolating to ITER is the effect of the divertor configuration, a factor of two difference in JET alone. The minimum of the density dependence of $P_{LH}$ also moves to about a 30% higher value in H than D. The dependence of $P_{LH}$ was also studied in mixed species plasmas. It was found that most of the variation in H-D mixtures was at less than 20% or more than 80% H concentration, with little variation in between. Helium-4 fuelling into H plasmas was also performed, resulting in a ~25% reduction of the threshold with up to about 10% He concentration. This reduction in L-H threshold in H-He mixtures may have application for the non-active phase of ITER operations. Detailed hydrogen and helium concentration analysis, transport simulations, and ICRH power deposition calculations have been performed to constrain interpretation of the mixed ion species effects. We will summarize results across all JET-ILW $P_{LH}$ data and the implications of the conclusions for ITER.

Speaker: Dr Jon Hillesheim (Culham Centre for Fusion Energy)

hillesheim_iaea2018_16x9v2.pdf

summary_slide_27sep2018.pdf

383 L-H Transition Trigger Physics in ITER-Similar Plasmas with and without Applied n=3 Magnetic Perturbations

Quantitative proof is presented that the ion polarization current [1] dominates the evolution of the radial electric field E_r across the L-H transition, and needs to be properly taken into account in Ohm’s law. This is an important step towards developing a physics-based reduced L-H transition model, which in addition needs to include at a minimum the poloidal momentum balance, and evolution equations for the turbulence intensity and the pressure gradient [2]. The observed isotope dependence of the threshold power P_LH in ITER-similar H, He and D plasmas [3] can then be qualitatively understood: in D and He, where the Reynolds stress [2-4] dominates the neoclassical bulk viscosity and thermal ion orbit loss, P_LH is relatively low. In hydrogen plasmas, where the Reynolds stress is marginal and comparable to the neoclassical bulk viscosity and thermal orbit loss current, P_LH is much higher. The observed increased transition time to full turbulence suppression in hydrogen plasmas can also be quantitatively understood using this model. Resonant magnetic perturbations (RMP) may have to be applied before the L-H transition in ITER to safely suppress the first ELM. In ITER-similar plasmas in DIII-D the increase of P_LH with n=3 RMP is most pronounced with ECH, with P_LH increasing with decreasing plasma collisionality [P_LH~(nu_star)^-0.3]. Two-fluid modeling with the M3D-C1 code [5] shows that the normalized L-mode radial density gradient a/L_n is toroidally modulated and periodically increased on the outboard midplane with applied RMP. Non-axisymmetric modifications with RMP include increased local long-wavelength turbulence (measured via BES) and reduction of the E_r well and ExB shear. We conjecture that the increase in threshold power with RMP results from locally enhanced instability drive (however without simultaneously increased Reynolds stress) and reduced ExB shear. This work was supported by the US Department of Energy under DE-FG02-08ER54984, DE-FG02-08ER 54999, DE-AC05-00OR22725, and DE-FC02-04ER54698. [1] K. Itoh, Plasma Phys. Control. Fusion 36 A307-A318 (1994). [2] K. Miki, P.H. Diamond et al., Phys. Plasmas 19, 092306 (2012). [3] Z.Yan et al. Nucl. Fusion, 57, 126015 (2017). [4] L. Schmitz, Proc. 26th IAEA Fusion Energy Conf., Oct.17-22, 2016, Kyoto, Japan, paper EX-C P571. [5] R.S. Wilcox et al. Nucl. Fusion 57 116003 (2017).

Speaker: Dr Lothar Schmitz (University of California-Los Angeles)

Schmitz_EX4-2_Summary.pptx

Schmitz_IAEA_12.pptx

384 Gyrokinetic Analysis and Simulations of Pedestals

Major progress has been made in understanding the pedestal transport in several areas. 1) For the first time, the instabilities that dominate energy transport in present experimental pedestals are determined, using identifying ratios of the transport they produce in different channels - their “transport fingerprint”. These are derived from the drift kinetic equation for pedestal parameters, and corroborated by gyrokinetic simulations using GENE[1]. For the typical case where the electron density sources are relatively small compared to the energy sources, MHD-like modes (such as KBM) cannot dominate pedestal energy transport. The analysis is applied to experimental observations from multiple devices, and also, in detail to two DIII-D pedestals, considering transport in multiple channels, measured fluctuations and pedestal equilibrium reconstructions. Micro-tearing modes (MTM) and Electron Temperature Gradient (ETG) modes dominate energy transport, rather than KBM. Multiple disparate experimental observations can be explained and unified using this analysis, including, surprisingly, density transport from applied Resonant Magnetic Perturbations (RMP). 2) Gyrokinetic simulations of velocity shear suppression of ITG for pedestal equilibria, using GENE[1], find excellent agreement, in detail, with the decorrelation theory of Zhang and Mahajan[2]. This physics-based theory can thus be exploited to estimate/predict turbulent transport in new regimes. In a controlled $\rho^*$ scan (velocity shear ~ $\rho^*$), the suppressed heat flux from ITG modes scales much more poorly than gyro-Bohm, so that it may become relatively large at the low $\rho^*$ of burning plasmas, unlike present experiments. 3) Hence, a detailed examination of the properties of ITG/TEM modes in pedestals and ITBs with high $\beta_{pol}$ has been undertaken. Unlike core modes, pedestal electrostatic modes are slab-like: destabilization results from parallel resonances, not curvature. Consequently, the density gradients are stabilizing in pedestals, and so is high $\beta_{pol}$, impurities and impurity gradients. Routes to optimize confinement in fusion relevant tokamaks, for both for inductive and steady state operations, are discussed. [1]Jenko F., Dorland W., Kotschenreuther M., et. al., Phys. Plasmas 7 (2000) 1904 [2]Y. Z. Zhang and S. M. Mahajan, Physics of Fluids B, 5, (1993) 2000

Speaker: Dr Mike Kotschenreuther (Institute for Fusion Studies)

IAEA 2018 916B11.pdf

Summary slide mtk.pptx

385 Transport Barriers in DIII-D High βp plasmas and Development of Candidate Steady State Scenarios for ITER

Shafranov shift stabilizes turbulence and creates a bifurcation in kinetic ballooning mode(KBM) transport that enables high performance ITB plasmas to be sustained at reactor relevant $q_{95}$. On DIII-D, the internal transport barrier (ITB), high $\beta_N$ ~3, and very high normalized confinement $H_{98,y2}$~1.6 of the high $\beta_p$ scenario has been achieved at $q_{95}$~6.5. This is projected to meet the ITER steady-state goal of Q=5. The ITB is maintained at lower $\beta_p$ with a strong reverse shear, confirming predictions that negative central shear can lower the $\beta_p$ threshold for the ITB. There are two observed confinement states in the high $\beta_p$ scenario: H-mode confinement state with a high edge pedestal, and an enhanced confinement state with a low pedestal and an ITB. At large radius (ρ=0.8), the enhanced ITB confinement state has a much lower predicted turbulent ion energy transport than the H-mode confinement state. Simulating intermediate states, a large electromagnetic “mountain” of increased transport is found due to a KBM. Transient perturbations such as edge localized modes (ELMs) may trigger the transition between states by temporarily reducing the KBM drive. It has been observed that when there are no large type I ELMs, and there is no transition to enhanced confinement otherwise observed with lower n=3 perturbation. Quasilinear gyro-Landau fluid predictive modeling of ITER suggests that only a modest reverse shear is required to achieve the ITB formation necessary for Q=5 when electromagnetic physics including the KBM is incorporated.

Speaker: Dr Joseph McClenaghan (Oak Ridge Associated Universities)

mcclenaghan_IAEA_FEC_presentation.pdf

McClenaghan_summaryslide.pptx

386 Core Density Peaking Experiments in JET, DIII-D and C-Mod in Various Operational Scenarios - Driven by Fuelling or Transport

Core density profile peaking has been extensively studied by performing several dimensionally matched collisionality scans in various plasma operation scenarios on JET as well as by executing a 3-point collisionality scan on DIII-D and a 2-point collisionality scan in I-mode on C-Mod. In L-mode, D and V are large in all cases even if the NBI power is much smaller than in the H-mode cases. However in H-mode, D and V are both small, and therefore, NBI fueling plays an important role in contributing to density peaking. These small D and V here represent electron particle transport, but there is evidence now from JET that the ion particle Di and Vi can be an order of magnitude larger. Gyro-kinetic GENE simulations were performed to infer the peaking factor of background ions. Peaked density profiles are obtained only for L-mode while H-modes discharges show flat or hollow density profiles at ρ=0.6. TGLF and QuaLiKiz transport simulations confirm the dominant role of NBI fueling in producing peaked ne profiles in JET H-mode plasmas. A similar 3-point collisionality scan to JET was performed on DIII-D. Density peaking increased with collisionality very similarly to JET. The perturbative analysis from the gas puff modulation data confirms the significant role of NBI fueling in each case. The dependence of density peaking on collisionality was studied in I-mode and L-mode on C-Mod by applying gas puff modulation. The steady-state ne data indicates no dependence on collisionality in neither I- nor L-mode, consistent with JET but in contrast to H-mode data in C-Mod. The results from the scans on various tokamaks and modelling all indicate that in H-mode the NBI fueling is a significant contributor to density peaking. The consequences of this on ITER fueling will be discussed. Acknowledgement: This work has been carried out within the framework of the EUROfusion Consortium and has received funding from the Euratom research and training programme 2014-2018 under grant agreement No 633053. The views and opinions expressed herein do not necessarily reflect those of the European Commission. This material is based upon work supported by the Department of Energy under Award Number DE-FC02-04ER54698. Supported by U.S. Department of Energy awards DE-FC02-99ER54512, DE-SC0007880 using Alcator C-Mod, a DOE Office of Science User Facility.

Speaker: Dr Tuomas Tala (VTT)

Tala_IAEA_2018_talk.pptx

Tala_IAEA_2018_talk.pptx

Banquet

Thursday, 25 October

EX/3, EX/4, TH/2 P5 Posters

387 A gyrokinetic discovery of fast L-H bifurcation physics in a realistic, diverted, tokamak edge geometry

Speaker: Dr Seung-Hoe Ku (Princeton Plasma Physics Laboratory)

Ku.S-TH2-1_summary.pptx

388 Core Density Peaking Experiments in JET, DIII-D and C-Mod in Various Operational Scenarios - Driven by Fuelling or Transport

Speaker: Dr Tuomas Tala (VTT, Association Euratom-Tekes)

IAEA_paper_Tala.pdf

Tala_IAEA2018_one_slide_summary.pptx

389 Developing steady state ELM-absent H-mode scenarios with advanced divertor configuration in EAST tokamak

Speaker: Prof. Giuseppe Calabro (University of Tuscia)

390 Gyrokinetic Analysis and Simulations of Pedestals

Speaker: Dr Mike Kotschenreuther (Institute for Fusion Studies)

Summary slide mtk.pdf

391 Implications of JET-ILW L-H Transition Studies for ITER

Speaker: Dr Jon Hillesheim (Culham Centre for Fusion Energy)

392 Increasing the Density in W7-X: Benefits and Limitations

Speaker: Dr Golo Fuchert (Max-Planck-Institut für Plasmaphysik, Greifswald, Germany)

IAEA_poster_fuchert.pptx

summary_slide_fuchert.pdf

393 Integrated operation of steady-state long pulse H-mode in EAST

Speaker: Prof. Xianzu Gong (Insititute of Plasma Physics, Chinese Academy Sciences)

EX/3-1 Summary Slides_2018_Gong_v3

394 Integration of the high- N hybrid scenario to a high performance pedestal, stable zero torque operation and a divertor solution

Speaker: Dr Francesca Turco (Columbia University)

turco_summary.pdf

395 L-H Transition Trigger Physics in ITER-Similar Plasmas with and without Applied n=3 Magnetic Perturbations

Speaker: Mr L. Schmitz (University of California-Los Angeles)

396 Optimisation of JET-DT and ITER operation by developing an understanding of the role of low-Z impurity on the H-mode pedestal

Speaker: Dr Carine Giroud (CCFE)

cgiroud_preprint_iaea2018_v05.pdf

cgiroud_summary_slides_ex_3_4_iaea2018.pdf

397 Scenario development for DT operation at JET

Speaker: Dr Luca Garzotti (United Kingdom Atomic Energy Agency - Culham Centre for Fusion Energy)

65535_oral_iaea_2018_v4.pptx

Summary slide V2.pdf

398 Transport Barriers in DIII-D High bp plasmas and Development of Candidate Steady State Scenarios for ITER

Speaker: Dr Joseph McClenaghan (Oak Ridge Associated Universities)

McClenaghan_summaryslide.pptx

EX/5, PPC/1 - TH/3 Integrated Modelling & Transport

399 First principles and integrated modelling achievements towards trustful Fusion power predictions for JET and ITER

Predictability of burning plasmas is a key issue for designing and building credible future fusion devices. The integration of several physics aspects is mandatory for an accurate extrapolation from present day plasmas, mainly with deuterium (D) as the main ion species, to conditions in which the ion mixture will be dominated by Deuterium-Tritium (DT). In this framework, an important effort of physics understanding and guidance is being carried out in parallel to the JET experimental campaigns in H, D and T by performing analyses and modelling towards an optimization of the JET-DT neutron yield and fusion born alpha particle physics. Analyses performed for both baseline and hybrid regimes have shown that reproducibility of heat and particle transport in D plasmas with quasi-linear models as TGLF and Qualikiz is acceptable, showing that in general low density is preferable in the hybrid regime in order to boost the neutron rate generation. This is due to the higher penetration of the NBI beams at low density but as well because in the Ion Cyclotron Resonance Heating (ICRH) schemes usually used, H minority, the 2nd harmonic accelerates the central D beams boosting the fusion reactivity and as well reducing turbulence driven by the so called Ion Temperature Gradient (ITG) modes. For heat and particle transport, quasi-linear models tend to deviate more in H than in D which makes the prediction for T and DT campaigns less satisfactory. Therefore, the comparison of those models against gyrokinetic simulations has been started which has led to a significant improved understanding of the so called isotope effect which can be reproduced in particular circumstances. Gyrokinetic simulations performed with the GENE code show that the fast ion fraction, the ExB shearing rate or the electromagnetic effects, can lead to deviations from the expected GyroBohm (GB) scaling. Extrapolations to JET-DT from recent experiments using the maximum power available have been performed including some of the most sophisticated codes and a broad selection of models. There is a general agreement that 11-15MW of fusion power can be expected in DT for the hybrid and baseline scenarios. On the other hand, in high beta, torque and fast ion fraction conditions, isotope effects could be favorable leading to higher fusion yield. This is in line with the fusion power aimed for such campaign.

Speaker: Dr Jeronimo Garcia (CEA IRFM)

FEC_india_v4_jeronimo_garcia.pptx

IAEA2018_slide.pptx

400 Transport characteristics of deuterium and hydrogen plasmas with ion internal transport barrier in LHD

A remarkable achievement of $T_{\rm i0} = 10$ keV with $Z_{\rm eff} = 2$ was obtained in Large Helical Device (LHD). In order to clarify transport characteristics in ion internal transport barrier (ion ITB) formation with isotope effect, a dataset of pure deuterium (D) ($n_{\rm D}/n_{\rm e} > 0.85$) and pure hydrogen (H) ($n_{\rm H}/n_{\rm e} > 0.85$) plasmas for high-ion-temperature (high-$T_{\rm i}$) regime were analyzed, and two mechanisms of transport improvement were characterized. A significant reduction of ion heat transport in D plasmas was observed in comparison between D and H plasmas, indicating non-gyroBohm mass dependence. The dependence of the heat transport on temperature ratio ($T_{\rm e}/T_{\rm i}$) and normalized $T_{\rm i}$-gradient ($R/L_{\rm Ti} = -(R/T_{\rm i})(dT_{\rm i}/dr)$) was investigated in the core region, in which gyrokinetic simulations with GKV code predicts the destabilization of ITG modes [1]. The $T_{\rm e}/T_{\rm i}$ dependence shows ITG-like property, while a significant deviation from the ITG-like property is found in the $R/L_{\rm Ti}$ dependence. Moreover, the density fluctuation is well correlated with the heat transport dependence on $T_{\rm e}/T_{\rm i}$ and $R/L_{\rm Ti}$, indicating suppression of ITG mode in large $R/L_{\rm Ti}$ regime and resultant ion ITB formation. The similarity of instabilities found by GKV indicates that both ITG suppression and isotope effect contribute to production of high-$T_{\rm i}$ plasmas ($T_{\rm i0}\sim10$ keV) with multiple-ion conditions.

Speaker: Prof. Kenichi Nagaoka (National Institute for Fusion Science)

Nagaoka_EX5-1_16_9_v3.pdf

Nagaoka_EX5-1_16_9_v3.pptx

Summary_EX5-1_Nagaoka.pptx

401 Predictive multi-channel flux-driven modelling to optimise ICRH tungsten control in JET

The evolution of the JET high performance hybrid scenario, including central accumulation of the tungsten (W) impurity, is reproduced with predictive multi-channel integrated modelling over multiple confinement times using first-principle based models. 8 transport channels ($T_i,T_e,n_D,n_{Be},n_{Ni},v_{tor},j$) are modelled predictively with self-consistent predictions for sources, radiation, and magnetic equilibrium, yielding a predictive system with multiple nonlinearities which can reproduce observed radiative temperature collapse after several confinement times. The mechanism responsible for W accumulation is inward neoclassical convection driven by the main ion density gradients and enhanced by poloidal asymmetries due to centrifugal acceleration. The slow timescale of bulk density evolution sets the timescale for central W accumulation. Prediction of this phenomenon requires a turbulent transport model capable of accurately predicting particle and momentum transport (QuaLiKiz) and a neoclassical transport model including the effects of poloidal asymmetries (NEO) coupled to an integrated plasma simulator (JINTRAC). The modelling capability is applied to optimise the available actuators to prevent W accumulation, and to extrapolate in power and pulse length. Central NBI heating is preferred for high performance, but comes at the price of central deposition of particles and torque which pose the risk of W accumulation. Several benefits of ICRH to mitigate W accumulation are examined: The primary mechanism for ICRH to control W in JET are via its impact on the bulk profiles and turbulent diffusion, which are insensitive to details of the ICRH scheme. High power density near the axis is found to be best to maximise the beneficial effects of ICRH against W, but changing the minority species or its concentration does not significantly change the W behavior. With attention to the location of the ICRH resonance and MHD stability, high performance hybrid scenario discharges of 5s at maximum power should be possible in the coming campaign, and a controlled and steady fusion performance in the subsequent JET DT campaign. This work demonstrates the integration of multiple first-principle models into a powerful multi-channel predictive tool for the core plasma, able to guide JET scenario development to its objectives of higher performance and longer pulses.

Speaker: Dr Francis Casson (CCFE, Culham Science Centre, Abingdon, UK)

Casson_IAEA_2018_slides3.pdf

Casson_IAEA_2018_slides3_wide5.pdf

Casson_IAEA_poster2a.pdf

Casson_summary_slide.pdf

402 Predictive integrated modelling of plasmas and their operation scenarios towards exploitation of JT-60SA experiment

Plasmas and their operation scenarios have been predicted by using integrated modelling codes towards the exploitation of JT-60SA experiment. Through the close collaboration between Japan and EU including the model validation and verification using JT-60U and JET experimental data, the following key results were obtained in various modelling activities. Improved modelling predicted a steady-state high-beta ($\beta_N > 4$) plasma with an internal transport barrier (ITB), its controllability to sustain the ITB location and target performance, and its tolerance to the core accumulation of impurity seeded to reduce the divertor heat load below 10 MW/m$^2$, with actuator powers within the machine capability. Integrated rotation and pedestal modelling for inductive scenarios revealed that the rotation with the neoclassical toroidal viscosity (NTV) due to the toroidal magnetic field ripple degrades the pedestal height, but it is high enough to achieve target parameters, and error field correction coils in JT-60SA have the potential to control the rotation by changing NTV. The obtained predictions clarified the JT-60SA capability to explore the plasma scenarios indispensable to ITER and DEMO.

Speaker: Dr Nobuhiko Hayashi (National Institutes for Quantum and Radiological Science and Technology)

IAEA18_Hayashi_v11_limit_c.pptx

Summary_slide_PPC:1-1.pptx

403 Predicting the Toroidal Rotation Profile for ITER

Toroidal rotation in ITER is predicted with a combination of intrinsic and NBI sources and gyrofluid modeling of momentum transport, and it is found to play a significant role in enhancing D-T fusion performance. In a large tokamak such as ITER, intrinsic sources of rotation as well as rotation drive from applied 3D fields will become more significant due to a relatively low amount of neutral beam torque. The predicted intrinsic rotation at the top of the pedestal in ITER is 10 krad/s, and the core rotation driven by NBI is predicted to be ~20 krad/s. The predicted rotation for ITER is large enough that the TGLF transport model predicts significant turbulence stabilization, leading to improved confinement and an increase in the predicted fusion gain (Q) from 5 to 8 when rotation effects are included and the core density is assumed to be flat. Q is further increased to 11 when TGLF is also used to self consistently determine the core density. The predicted intrinsic rotation is derived from dimensionless parameter scan experiments that measured the dependence of intrinsic torque on ρ\*. Confidence in this prediction has been increased with experiments that investigated important uncertainties in the intrinsic torque measurements: the role of fast-ions on the measurement of intrinsic torque, and the effect of neutrals on momentum transport in the pedestal. Intrinsic rotation measured in a ρ\* scan yielded a consistent dependence on ρ\*, and intrinsic rotation was not found to be affected by significant changes in divertor closure when other important parameters were held constant. In addition, it was found that intrinsic rotation undergoes no significant change at the onset of detachment. These results increase confidence in the prediction of the intrinsic rotation in ITER. The dependence of intrinsic rotation on ρ\* found in this work appear to be inconsistent with completely independent database studies of intrinsic rotation. However, careful analysis shows a common dependency on ion temperature that underlies the similar predictions from these different methods. This work was supported in part by the US Department of Energy under DE-FC02-04ER54698 and DE-AC02-09CH11466, and carried out within the framework of the EUROfusion Consortium and has received funding from the Euratom research and training programme 2014-2018 under Grant Agreement No. 633053.

Speaker: Dr Colin Chrystal (General Atomics)

chrystal_2018IAEA.pdf

chrystal_IAEA2018_summary.pptx

P5 Posters

404 A power-balance model of density limit in fusion plasmas

A density limit (DL), causing either a disruption or a soft termination of the discharge, is generally found in magnetic confinement fusion devices. Some empirical scaling laws have been proposed to order the maximum achievable densities. The Sudo density, n_Sudo∝(P〖 B〗_ϕ )^0.5 [1], with P the heating power, is generally applied to the stellarator. The Greenwald density, n_G=I_p⁄((π a^2 ) ) [2], represents a reference for the ohmic tokamak and the Reversed Field Pinch (RFP): a remarkable feature given the differences of these two configurations both in terms of magnetic profiles and transport properties. Additionally heated tokamak experiments in L-mode suggest scaling laws of the form P^(0.3÷0.5) I_p^(0.5÷1) [3, 4]. The H-mode tokamak DL, identified by a back transition to L-mode and therefore non disruptive in general, seems to be more device dependent [5, 6]. We present a basic power-balance model [7], providing a unified interpretation of DL in the stellarator, in the L-mode tokamak and in the RFP. In fact, scaling laws resembling the above empirical trends, but richer in their parametric dependence, are derived as special cases of a more fundamental relation, which delimits the thermal equilibrium states having realistic temperature profile (i.e. with low temperature only at the edge) in the presence of radiation losses due to light impurities and edge neutrals. This equation is just the detachment condition discussed in [8] within the stellarator framework. Our analysis shows that it can be applied to any magnetic configuration. In particular, by combining this equation with on-axis Ohm’s law and Spitzer’s resistivity, a Greenwald-like scaling law is obtained, having a tenuous dependence on thermal transport: this explains why the DL does not change appreciably passing from the ohmic tokamak to the RFP. Nonetheless, this scaling departs from the pure Greenwald limit, due to further dependences on the impurity content as well as on the heating power. We show that it describes better than the pure Greenwald limit high density disrupted L-mode experiments performed at TCV and JET.

Speaker: Dr paolo zanca (consorzio rfx)

summary slide_zanca_TH_P5_22.pdf

405 Aditya up-gradation equilibrium study

The ADITYA tokamak device is used to produce circular plasma for few hundreds of milli-seconds. The edge physics study in this device is led to significant contributions. The upgradation of this device is focused to address issues relevant to heat removal capability at the plasma edge. This requires to construct plasma equilibrium with divertor configuration. In this regard, additional pair of coils at the inboard and outboard are used to construct plasma equilibrium. The inboard pair mainly creates the divertor configuration while the outboard pair provides flexibility in increasing the size of the plasma. This study has shown that plasma equilibrium with double null configurations can be produced for plasma current up to 100 kA and with plasma poloidal beta of 0.3. The limit on the plasma parameter is due to restriction on the allowable divertor coil current which is limited to 150 kAt. The radial distance of divertor null point is kept at least 3 cm away from the circular shaped vacuum vessel so that the divertor configuration can be ensured.

Speaker: Mrs Deepti sharma (Institute for Plasma Research, Gandhingar, India)

FEC-Summary.pdf

406 Centrifugal force driven low frequency modes in spherical tokamak

There is a longstanding issue on the physical nature of a low frequency (<50 kHz) MHD instability observed at the early phase of the discharges of a spherical tokamak (ST) - the National Spherical Torus Experiment (NSTX) (Ono et al 2000 Nucl. Fusion 40 557). This work provides evidence that low frequency modes in spherical tokamaks are often driven by the rapid plasma flow. The centrifugal force associated with toroidal plasma flow is identified as the key physics mechanism for generating this instability located in the plasma core region. Positive mode identification between toroidal modeling and experiments is achieved for the mode frequency, the mode internal structure, as well as the threshold flow value for the mode onset. The threshold flow value weakly depends on the precise value of safety factor and the mode is located around the location of sharp density gradient. More important, since the achievable rotation value on NSTX is comparable with that for future Component Test Facilities (CTF) based on ST (Peng et al Plasma Phys.Control. Fusion,47,B263), the presented results in this work are helpful for the conceptual design of ST-CTF to avoid the instability driven by fast plasma flow.

Speaker: Dr G.Z. Hao (Southwestern Institute of Physics, Chengdu 610041, China)

407 Characteristics of electromagnetic turbulence on KTX experiment device

Electrostatic turbulence is the main constrain of confinement improvement on low $\beta$ toroidal magnetic confinement devices. With the development of high $\beta$ operation scenario, electromagnetic turbulence is expected to become important for development of resistive tearing mode and resistive wall mode. The characteristics of electromagnetic turbulence on KTX are studied in low current tokamak and in reversed field pinch plasma operations. Electron density fluctuations in the core are measured based on forward scattering signal collection with multi-channel interferometer system. The edge electric and magnetic field fluctuations are measured using movable multi-functional probe arrays. The 3D spectral characteristics of the electromagnetic turbulence are present in our research. Biased electrode is applied at the edge of plasma for changing the edge electric field profile, and significant suppression of turbulence and reduction of radial particle flux are observed after applying high biasing voltage.

Speaker: Dr Wenzhe Mao (University of Science and Technology of China)

summary slide.pdf

408 Comparative simulations of the plasma response to RMPs during ELM-crash mitigated and suppressed phases in KSTAR

Control of the edge localized modes (ELMs) is one of the most critical issues for a ITER and the future tokamak fusion reactors. In order to develop a *predictive* model of the access to ELM-crash suppressed states, it is essential to understand first the underlying physics mechanism of ELM-crash-suppression. This paper reports comparative simulation results for particular KSTAR experimental shot, where both of the ELM mitigated and suppressed phases were observed sequentially and separated distinctly in time with low-n resonant magnetic perturbations (RMPs) in KSTAR. We have observed that toroidal ($\omega_t$) and ExB ($\omega_{ExB}$) rotation frequencies are increased, while electron pressure gradient and the associated electron diamagnetic rotation frequency ($\omega_{*e}$) reduced near the pedestal top through the transition from mitigation to suppression of ELMs. This results in a small outward shift in the zero-crossing of the electron perpendicular rotation ($\omega_{\perp e} \sim 0$) and $\omega_{\perp e}$ becomes even smaller inside the pedestal. Correspondingly, two-fluid linear plasma response modeling with the resistive MHD code M3D-C1 [1] indicates that resonant tearing response is increased significantly near the pedestal top, which is well correlated to the observed onset of ELM-crash suppression. This result is similar to the recent ECEI observation of perpendicular flow changes at the onset of ELM-crash suppression in KSTAR [2]. It remains unclear how the RMP-driven transport (with associated kinetic effects) bring out such changes to the rotation profiles and we plan to study that with XGC0 [3] and XGC1 [4] codes. Detailed results will be presented. References: [1] N. M. Ferraro, Phys. Plasmas **19**, 056105 (2012); [2] J. H. Lee *et al*., APS-DPP (2017); [3] G. Y. Park *et al*., Phys. Plasmas **17**, 102503 (2010); [4] C. S. Chang *et al*., Phys. Plasmas **16**, 056108 (2009)

Speaker: Dr Gunyoung Park (National Fusion Research Institute)

409 Development of the q=1 Advanced tokamak Scenarios in HL-2A

Advanced tokamak scenario with central q close to 1 has been achieved on HL-2A tokamak. An ITB has been observed during the nonlinear evolution of a saturated long-lived internal mode (LLM) or fishbone activities in HL-2A discharges as the q-profile formed a very broad low-shear region with qmin ~ 1. Such steep ion temperature-gradient zone locates around r/a=0.5-0.6 with Ti>Te. The observed normalized ion temperature gradient (R/LTi) is of 10.6, which exceeded the value for a level without ITB of∼6.5. Here, R is the major radius and LTi is the scale length of the Ti gradient defined by LTi= aTi/(dTi/dρ). When the barrier forms, the turbulence is significantly reduced around ITB foot(r/a=0.6), as measured by reflectometry in figure 2. The simultaneous excitation of the ITB and the bursting internal mode can only occur if the q-profile in the core remains flat in the plasma central region. This confirms the role played by the central internal kink instabilities in the production of ITBs in reversed or weak shear plasmas.
It was found that the q min reaching an integer value (q =1) throughout the ITB period, and there is a correlation between the emergence of the ITB formation and the evolution of central magnetic shear due to the perturbation of m=1/n=1 LLM or fishbone activity. A possible explanation for the LLM or fishbone being able to trigger or sustain ITBs is that the interaction between MHD instabilities and fast ion leads to a redistribution of the resonant fast ion. Based on this assumption, dedicated experiment have attempted to reproduce the stationary advanced scenario with q0 close to 1 by applying extra ECRH for enhancement of the fishbone activities. With strong fishbone activities enhanced by application of ECRH, this scenario does exhibit a clear prolonged ITB during the stationary phase of the discharge, extending the domain of existence of ITB form 10 confinement times to 20 confinement times, and the confinement enhancement factors over ITER89P L-mode scaling, form HITER89-P=1.7 to a new level of HITER89-P=2.1.

Speaker: Prof. YI LIU (Southwestern Institute of Physics)

My contribution.ppt

410 Ecton Mechanism of Energy Load on ITER-grade Tungsten Limiter T-10 Tokamak and Forecast for ITER.

Extreme high heat loads, both during steady state and transient events, expected on the tungsten divertor plates of the ITER facility, undertaken at Cadarache, France. In this paper nonambipolar plasma flow toward the surface, due to arcs and sparks, was investigated as mechanism of power exhaust, leading to enhanced heating of plasma facing materials (PFMs) at a very high heat load. This ecton mechanism results in the pulsed-periodic ignition of the explosive electron emission events providing high enough electron current from the wall. Unlike standard thermionic emission, such mechanism can dramatically increase electron emission and, as a result, sparks and arcs activity, leads to a surface overheating and melting. Such phenomenon have been observed in experiments on the T-10 tokamak with ITER-grade tungsten (W) poloidal limiter under a powerful plasma electron cyclotron resonance heating (ECRH) and plasma ring shifted inside. In such conditions, the interior tungsten plates of limiter were heated up to temperature exceeded 20000C, estimated local thermal load were of more than 40 MW/m2 on the plates edges, leading to surface melting. Intensive sparking and arcing, deep cracks and edge melting were observed on W tiles. Also, tiles surfaces were flood by recrystallized tungsten. All W tiles surface are covered by two crater types: deep, (with dimensions from 10 to 100 µm) and acetabuliform type (with dimensions from 0.5 - 20 µm) arranged in a ‘long chains’ - vacuum arcs, and a ‘short chains’ - vacuum sparks. The reason of such sub-μs discharges ignition can be plasma-turbulence-driven fluctuations of particle and energy flux to the plasma-modified surface. The report analyzes consequences for ITER the EEE appearance on the divertor W surface - the sharpening of SOL power width distribution, parallel to the magnetic field – q; the melting of the W leading edges of divertor targets and the recrystallization of the W surface as a result of the superheated liquid metal droplets appearance. Melt tungsten can be subject to J × B force. EEE can lead to the erosion enhancement of the divertor plates. Micro-explosions lead to droplets, which, like dust particles, can effectively deliver impurities to the central region of the plasma.

Speaker: Mr Leonid Khimchenko (ITERRu)

411 Effect of LBO-seeded Impurity on ELMs in the HL-2A tokamak

Effect of the pedestal deposited impurity on the edge-localized mode (ELM) behaviour has been observed and intensively investigated in the HL-2A tokamak. Impurities have been externally seeded by a newly developed laser blow-off (LBO) system. Both mitigation and suppression of ELMs have been realized by LBO-seeded impurity. Measurements have shown that the LBO-seeded impurity particles are mainly deposited in the pedestal region. During the ELM mitigation phase, the pedestal density fluctuation is significantly increased, indicating that the ELM mitigation may be achieved by the enhancement of the pedestal transport. The transition from ELM mitigation to ELM suppression was triggered when the number of the LBO-seeded impurity exceeds a threshold value. During the ELM suppression phase, a harmonic coherent mode (HCM) is excited by the LBO-seeded impurity, and the pedestal density fluctuation is significantly decreased, the electron density is continuously increased, implying that HCM may reduce the pedestal turbulence, suppress ELMs, increase the pedestal pressure, thus extending the Peeling-Ballooning instability limit. It has been found that the occurance of the ELM mitigation and ELM suppression closely depends on the LBO laser spot diameter.

Speaker: Dr Yipo Zhang (Southwestern Institute of Physics)

2018 IAEA Paper_Zhang Yipo_final.pdf

412 Effects of magnetic perturbations on magnetic field stochastication during edge pedestal collapse

Edge localized modes (ELMs) are quasi-periodic relaxation of tokamak pedestal, releasing large heat flux on divertor places. Although ELMs are thought to be triggered by MHD peeling-ballooning instability, the nonlinear relaxation process is not fully understood. MHD filaments can carry out heat to scrape of layers (SOL) without reconnection [1]. On the contrary, a magnetic topology change due to magnetic reconnection may drive heat and particle out of plasmas. But a reconnection mechanism is not clear in the peeling-ballooning dominated plasmas. Nonlinear generation of tearing-parity fluctuations out of ballooning modes was proposed by Rhee et al. [2] as a candidate for the reconnection mechanism, further leading to stochastic magnetic field regions. In this work, we investigate how the pedestal collapse scenario is modified in the presence of resonant magnetic perturbations (RMPs), using resistive reduced MHD simulations. It is found that RMPs tends to inhibit the growth of the primary/secondary tearing fluctuations, indicating possible modification of a pedestal relaxation process. The growth reduction for the secondary mode correlates with larger pressure and larger magnetic perturbation strength. The detailed nonlinear analysis will be presented with the evaluation of degree of pedestal energy loss in the presence of magnetic perturbations. [1] H. Wilson and S. Cowley, Phys. Rev. Lett. 92, 175006 (2004) [2] Rhee \etal, Nucl. Fusion, 55, 032004 (2015)

Speaker: Dr Juhyung Kim (National Fusion Research Institute)

413 Effects of Microtearing Modes on the Evolution of Electron Temperature Profiles in High Collisionality NSTX discharges

A goal of this research project is to describe the evolution of the electron temperature profiles in high collisionality NSTX H-mode discharges. In these discharges the ion thermal transport is generally near neoclassical levels. However, it is found that the electron thermal transport is anomalous and can limit the overall global energy confinement scaling. Gyrokinetic simulations indicate that microtearing modes (MTMs) are a source of significant electron thermal transport in these discharges. In order to understand the effect MTMs have on transport and, consequently, on the evolution of electron temperature in NSTX discharges, a reduced transport model for MTMs has been developed. The dependence of the MTM real frequency and growth rate on plasma parameters, appropriate for high collisionality NSTX discharges, is obtained employing the new MTM transport model. The dependencies on plasma parameters are compared and found to be consistent with MTM results previously obtained using the gyrokinetic GYRO code. The MTM real frequency, growth rate, magnetic fluctuations and resulting electron thermal transport are examined for high collisionality NSTX discharges in systematic scans over plasma parameters. The electron temperature gradient along with the collision frequency and plasma beta are found to be sufficient for the microtearing modes to become unstable. In earlier studies it was found that the version of the Multi-Mode (MM) transport model, that did not include the effect of MTMs, provided a suitable description of the electron temperature profiles in high collisionality standard tokamak discharges. That version of the MM model included contributions to electron thermal transport from the ion temperature gradient, trapped electrons, kinetic ballooning, peeling ballooning, collisionless and collision dominated MHD modes, and electron temperature gradient modes. When the MM model, that includes transport associated with MTMs, is installed in the TRANSP code and is utilized in studying electron thermal transport in high collisionality NSTX discharges, it is found that agreement with the experimental electron temperature profile is significantly improved. Future research will involve improving the electron thermal transport model for low collisionality NSTX discharges. *Supported by the U.S. DoE, DE-SC0013977, DE-FG02-92ER54141, and DE-AC02-09CH11466.

Speaker: Dr Francesca Poli

414 Electric potential and turbulence in OH and ECRH low-density plasmas

New experimental observations and theoretical description of the plasma potential and radial electric field Er formation in the T-10 tokamak are presented. The potential was measured by heavy ion beam probe (HIBP) diagnostic from the plasma core to edge with high spatial (<1 cm) and temporal (1 mus) resolution, and by Langmuir probe (LP) at the edge. Low-density OH deuterium plasma (nе=1.01019 m–3, Te<1.3 keV, Ti <0.6 keV) is characterized by a negative potential up to phi(0.25)=-800 V. The potential profile is monotonically increasing towards the edge. The off-axis (rhoEC=0.5) ECRH with power PEC-off <1.7 MW (fEC=144 GHz) leads to the formation of a flat Te profile at 2 keV inside rho EC. It causes a dramatic raise of the core potential to positive values over the whole observation area, forming nearly zero Er. Extra nearly on-axis (rho=0.2) ECRH with PEC-on<0.5 MW (fEC=129 GHz) leads to a further increase of Te up to 3.3 keV, and to potential raise to phi(0.25)=+900 V forming an extended area of positive Er, from the core to the edge. Also HIBP and LP measure Geodesic Acoustic Modes (GAMs) and broadband (f <400 kHz) turbulence of the potential and density. GAMs with higher frequency satellite are dominating in potential power spectra in OH plasma, GAM amplitude increases during ECRH. Both GAM and satellite have uniform structure with constant frequencies over a wide radial extension, exhibiting the features of global eigenmodes of plasma oscillations. At the edge, a quasicoherent (QC) electrostatic mode (f~50-120 kHz) coexists with the GAM A Stochastic Low Frequency (SLF) mode with frequency <50 kHz is seen in the plasma density and potential power spectra, density poloidal coherence and cross-phase, exhibiting the poloidal rotation opposite to QC mode. Neoclassical (NC) modeling use various codes, from the simple analytical approach to the orbit code VENUS+delta f. The radial profiles and the main tendencies like potential decrease with density raise and potential raise with Te increase due to ECRH were reproduced by NC models. The turbulent dynamics in the edge plasma was described by the 4-field nonlinear two-fluid Braginskii model. The link between the potential and confinement is discussed.

Speaker: Dr Alexander Melnikov (NRC 'Kurchatov Institute')

paper_FINAL.pdf

415 Electromagnetic Analysis of APPEL Linear Device Magnets

The APPEL (Applied Plasma Physics Experiments in Linear Device) is an experimental system designed to carry out basic plasma physics experiments as well as serve as a test-bed for experimenting various plasma facings components interaction with strongly magnetized plasma. This versatile device consists of 16 large electromagnet coils weighing up to 700 kg each, which are made from CTC (Continuously Transposed Conductors), winded in double pancake configuration. Each electromagnet coil is made by sandwiching two double pancakes between 10 mm thick stainless steel plates to obtain 100 turns/ magnet. The individual coil has 52 cm internal diameter and outer diameter is around 110 cm. The stainless steel plates provide the necessary strengths to the magnets while its surface acts as radiator to dissipate the heat. The individual electromagnet can be operated continuously to produce peak axial magnetic field in excess of 0.1 Tesla by passing 750 A for 600s. All the 16 magnets in linear configuration produce peak magnetic field in excess of 0.5 Tesla by passing 750 A for 600s. In this set-up different magnetic field profile can be generated by optimizing the current using two high current D.C power supplies as well as configuration of the coils. The paper presents the electromagnets field simulation performed by Finite Element Analysis (FEA) using Comsol Multiphysics and ANSYS to obtain tailored magnetic field profile in linear, magnetic cusp & mirror configurations achieved in APPEL device. In-house magnetic field measurements carried out for the APPEL magnet and experimental validation of the FEA results. The heat loads and stresses on the coils have been calculated for steady state operation of the APPEL device.

Speaker: Ms Y Patil (Institute For Plasma Research)

summary slide_ypatil.pdf

416 Endogenous Magnetic Reconnection and Associated Processes of Relevance to Fusion Burning Plasmas

The main characteristic of an endogenous magnetic reconnection process is that its driving factor lays within the layer where a drastic change of magnetic field topology occurs. This kind of process is shown to take place when a significant electron temperature gradient is present in a magnetically confined plasma and when the evolving electron temperature fluctuations are anisotropic [1]. Then [2] two classes of reconnecting modes are identified. The localized class of mode involve a reconnected field ${{\tilde{B}}_{x}}$ of odd parity (as a function of the radial variable), characteristic phase velocities and growth rates differently from the commonly considered reconnecting modes associated with a finite effective resistivity. The width of the reconnection layer remains significant even when large macroscopic distances are considered. In view of the fact that there are plasmas in the Universe with considerable electron thermal energy contents, the features of the considered modes can be relied upon in order to produce generation or conversion of magnetic energy and high energy particle populations through a sequence of mode-particle resonances [3]. With their excitation, these modes acquire momentum in the direction of the main magnetic field component and the main body of the plasma column should recoil in the opposite direction [4].
Endogenous modes associated with a finite electron temperature gradient are shown to be sustained by the electron temperature heating rate due to the charged reaction products in a fusion burning plasma [5]. In this case, the longitudinal thermal conductivity on selected rational magnetic surfaces [5] is decreased, relative to its collisional value, by the effects of reconnection.
The best agreement between theory and experiments concerning the onset of magnetic reconnection is (probably) represented by the theory of the resistive internal kink mode [6]. This is reconsidered for regimes where the effects of local temperature gradients are important. *Supported by the U.S. DOE.
[1] B. Coppi and B. Basu, Phys. Lett. A, 382, 400 (2018).
[2] B. Coppi, Phys. Fluids, 8, 2273 (1965).
[3] B. Coppi, B. Basu, and A. Fletcher, Nucl. Fus., 57, 7 (2017).
[4] B. Coppi, Nucl. Fus., 42, 1 (2002).
[5] B. Coppi, et al., Nucl. Fus., 55, 053011 (2015).
[6] B. Coppi, R. Galvao, R. Pellat, et al., Fiz. Plazmy, 2, 961 (1976).

Speaker: Linda Sugiyama

417 Energetic-ion Driven Toroidal and Global Alfvén Eigenmodes on HL-2A

The stationary and nonstationary toroidal Alfvén eigenmodes (TAE) driven by energetic-ion have been observed on HL-2A. The mode frequencies are about 90-200 kHz and toroidal mode numbers for the most unstable mode are n=1–3. The radial structure of the mode with n=2 confirmed by the Alfvén Mode Code (AMC) make up of poloidal harmonic m=2 and m=3, which is a typical feature of TAE. The amplitudes measured by the Mirnov coils suggest that they are much stronger in the LFS than the HFS, which reveals a typical ballooning mode structure. In the down-chirping case, the mode frequency quickly sweeps down from the TAE gap center to the lower frequency gap accumulation point. The internal amplitude can be determined from the frequency sweep speed of TAEs and it will provide input for simulations of potential ion and alpha particle losses due to energetic particle driven modes. The TAEs were found to nonlinearly couple with tearing mode (TM) and result in the appearances of series of Alfvénic modes (AMs). An axisymmetric mode within the ellipticity-induced frequency gap driven by TAEs coupling with TM was found for the first time. The squared bicoherence suggests that two AMs with the same mode number but propagated in different diamagnetic drift directions couple together and lead to the generation of a high frequency mode with n=0. The symmetrical mode with an ’antiballooning’ feature prove to be global Alfvén eigenmodes (GAE). It is the even GAE with frequency around 240kHz, which agrees well with experimental observation of 235-240 kHz. The m=1 poloidal harmonic is dominated for the GAE. The experimental results also indicated that nonlinear mode-mode coupling degenerates the confinement of fast ions and it may be one of mechanisms of the energy cascade in energetic-particle turbulence or Alfvén turbulence.

Speaker: Mr Peiwan Shi (Southwestern Institute of Physics)

summary slide.pdf

summary slide.pptx

418 Equilibrium Pressure-Driven Current in the Presence of a Small Magnetic Island: Singular Behavior and Symmetry Effects

A small magnetic island has only a small effect on the ambient pressure gradient, so that the pressure is not constant on the flux surfaces in and near the island. The length scale determining which islands may be regarded as “small” in this context is determined by the ratio of perpendicular to parallel transport. We numerically explore the effect of such a small island on the MHD equilibrium current, assuming that the island is sufficiently large that the MHD perpendicular force balance equation retains its validity. This current plays an important role in determining the stability of the island. We show that the effect of a small island on the equilibrium current density can be significant. The pressure-driven current has, in general, a logarithmic (integrable) singularity at the X-line. In an MHD equilibrium that is invariant under combined reflection in the poloidal and toroidal angles (sometimes called “stellarator symmetry”), there is a cancellation, and the singular component of the pressure-driven current vanishes. Conventional models of magnetic islands used in analytical calculations have this symmetry property. Tokamaks with a single null divertor do not. In 3D MHD equilibrium solutions that are constrained to have simply nested flux surfaces, the pressure-driven current has a (nonintegrable) $1/x$ singularity near rational surfaces, where $x$ is the distance from the rational surface. We have numerically investigated the pressure driven current near a small magnetic island in a cylindrical magnetic field with perturbed circular flux surfaces. The perturbation consists of two components, one that modulates the toroidal magnetic field strength without breaking the flux surfaces, and a second that introduces a resonant radial component of the magnetic field at the rational surface but has little effect on the toroidal field. The relative phase between the two perturbations is varied. The Pfirsch-Schlüter current near the X-line is found to be much larger when both perturbations are present and the relative phase between the two breaks the stellarator symmetry than it is when these conditions are not satisfied. The solution near the X-line agrees with the asymptotic limit calculated in a previously published paper. This work was supported by DOE contract DE-AC02-09CH11466 and by the DOE SULI program.

Speaker: Allan Reiman (Princeton Plasma Physics Lab)

Summary_Slide_Reiman.pdf

419 First Plasma Scenario Development for HL-2M

HL-2M tokamak is now under construction in China as a modification to the HL-2A facility, with nominal parameters as follows: Ip=1.5-3.0MA, B=2.2T, major radius= 1.78m, minor radius=0.65m, elongation =1.6-1.8, triangularity >0.5. It is a real challenge to build a new machine in fusion community, HL-2M suffers from a long delay for the first plasma. In order to fulfil the requirement of engineering and government qualification of the machine in a short time, two first plasma scenarios for HL-2M are designed with a powerful plasma scenario design tool based on Matlab. The two scenarios, one for circular limited configuration and one for larger aspect ratio and lower elongation divertor configuration, are compatible with the magnetic diagnostic system and power supply system, which are not fully equipped and well tested. The PF current and voltage waveform for these two scenarios have been calculated with the plasma scenario design tool through a plasma resistive model which can estimate the resistive flux consumption. The key parameters for these two scenarios are as follows: toroidal field 1.4T, plasma current 200 kA with 1000 microsecond flattop. For the sake of simplicity and safety in first plasma campaign, only small parts of PF coils are used in the plasma discharge, no initial magnetization is exploited, no PF current zero-crossing is allowed, no vertical displacement event is allowed. To facilitate obtaining the plasma, two gyrotrons of 68GHz with 500kW each are exploited for preionization and assisted startup. The vacuum vessel baking temperature will reach to 300 Celsius degree during machine conditioning. In this paper, the geometric parameters of PF and CS, together with that of TF coils and Vacuum Vessel (VV). Also presented are an original matlab-based tool for tokamak modeling and plasma scenario development. With this tool, the current waveforms and voltage waveforms of CS and PF coils are calculated by a given plasma resistance model. The parameters of CS and PF coils presented here can provide reference for later plasma scenario design for HL-2M; the ideas for simple and safe first plasma scenarios can apply to other new machine in its first plasma campaign. This work is supported by the Chinese National Fusion Project for ITER under grant No. 2015 GB105004.

Speaker: Prof. Xianming SONG (Southwestern Institute of Physics)

420 Gyrokinetic Modeling with an Extended Magnetic Equilibrium including the Edge Region of Large Helical Device

We investigate radial electric field structure in Large Helical Device and its impact on high-energy particle loss at the material wall. We employ global gyrokinetic particle-in-cell code for whole-device simulation, X-point Gyrokinetic Code (XGC), which is currently being extended to non-axisymmetric geometries. The whole-device modeling of fusion plasma is needed to understand edge plasma phenomena strongly coupled to neoclassical and turbulent physics in the core region such as H-mode transition, divertor heat load, X-point particle loss and so on. As the first step, we have demonstrated two typical processes in LHD within the same framework of XGC : (i) GAM oscillation and its damping in a density profile or an electric field perturbation and (ii) long-time motion of high-energy particles and particle loss at the material wall. Our results are in agreement with previous simulation studies using separate codes. One is transport simulation limited in the core region and the other is particle tracing simulation without electric field perturbation. We have also investigated particle loss under the effects of ambipolar radial electric field, which is observed after GAM oscillation. The electric field affects the particle loss in two different ways in accordance with the particle energy: (i) confinement due to the inward electric field for high energy range and (ii) additional particle loss due to the disturbance of particle orbit for intermediate energy range. The electric field also affects the strike point of high-energy particle in divertors. The present scheme including (i) combined use of cylindrical and field-aligned triangle meshes and (ii) extension of VMEC equilibrium using a virtual casing method, would be promising for whole device gyrokinetic modeling of Stellarators without artificial boundary at the last closed flux surface.

Speaker: Dr Toseo Moritaka (Institue for Fusion Science)

T. Moritaka_IAEA2.pdf

421 Gyrokinetic-MHD coupled simulation of RMP plasma interaction reproduces density pump-out seen in the tokamak edge

The gyrokinetic neoclassical particle-in-cell code XGCa coupled to the MHD code M3D-C1 is applied to study the particle and heat flux caused by external 3D magnetic perturbations in a DIII-D H-mode plasma. Despite the existence of KAM surfaces in the pedestal, our simulations, which so far are limited to the 0.5 to 1 ms directly after the RMP field is switched on, show the beginning of density pump-out at the pedestal top as well as a steepening and narrowing electron temperature pedestal around the separatrix similar to observations in the DIII-D tokamak [L. Cui et al., Nucl. Fusion 17, 116030 (2017)]. The RMP field is known to enhance particle transport leading to density pump-out and to be able to suppress edge localized modes (ELMs) in tokamak plasma. Pump-out occurs with or without ELM suppression [R. Nazikian et al., Phys. Rev. Lett., 105002 (2015)], and understanding its physics basis is important for developing predictive understanding. Due to the short time scales studied so far with XGCa, core heat and torque sources, and turbulent transport can be neglected. Only an electron heat sink on the separatrix and in the scrape-off layer is added to model radiative cooling. The increased, RMP induced particle and energy fluxes observed in our study - despite the presence of KAM surfaces in the M3D-C1 computed screened RMP field - are mostly of convective nature as can be seen from the weak change in the electron temperature compared to the particle density at the pedestal top. While these XGCa simulations already reproduce essential experimental findings such as the beginning density pump-out and the convective nature of the RMP induced energy flux, several enhancements are being investigated. Those enhancements include initializing the simulation with experimental toroidal rotation profiles, adding NBI torque source, replacing the simple SOL heat sink by an actual model for impurity radiation, and adding a turbulent transport model, and core heat and torque sources. Self-consistent, kinetic calculation of the screened RMP field with an XGCa-internal solver for Ampére's law and comparison to the M3D-C1 screened RMP field is investigated as well. Supported by the US Department of Energy (contracts DE-AC02-09CH11466, DE-FC02-04ER54698). Computing time provided by ALCF (DE-AC02-06CH11357) and NERSC (DE-AC02-05CH11231) through ALCC, INCITE, and ERCAP.

Speaker: Dr Robert Hager (Princeton Plasma Physics Laboratory)

R-Hager_TH-P5-9_Summary_csc3.pptx

422 Influence of electron cyclotron resonance heating on ion heat conductivity in T-10 plasma

Investigation of ion heat conductivity in plasma with ECR-heating and suppressed saw-teeth and modes $(m,n)=(1,1)$ and $(2,1)$ is carried out. Off-axis heating (localization radius is $\rho=r/a \approx0.5$) and combined heating (on-axis ECRH together with off-axis) are considered. It is shown for the ohmic stage that ion heat conductivity is on a neoclassical level in the central zone $\rho \leq 0.5-0.6$ but it is clearly anomalous outside these radii. Off-axis heating does not lead to any notable changes of the heat conductivity profile. In the regime with combined heating additional $\approx0.5$ MW on-axis ECR-power results in ion heat conductivity magnification up to $\approx1.5$ times and $\approx1$ MW on-axis ECR-power causes the increase up to $\approx2$ times.

Speaker: Mr Maxim Nurgaliev (National Research Centre "Kurchatov Institute")

Poster_Nurgaliev_EX_P5-21 .pdf

423 Ion kinetic effects on MHD instabilities in high beta LHD plasmas

For the high beta plasmas in the inward shifted Large Helical Device (LHD) configurations, the plasma peripheral region is theoretically MHD unstable region since there is always a magnetic hill in the plasma peripheral region. However, high beta plasmas with about 5% of the volume averaged beta value are stably obtained in the LHD experiments. This implies that the nonlinear saturation level of the MHD instabilities does not significantly affect the plasma confinement. On the other hand, the previous MHD simulation study showed that resistive ballooning modes are unstable in the plasma peripheral region and the central pressure is significantly decreases since the influence of the instabilities expands to the core region. In order to resolve the discrepancy between the experimental results and the simulation results, numerical analyses based on the kinetic MHD model have been carried out in this study. In the kinetic MHD model used here, the drift kinetic description is used for ions and the fluid model is used for the electron. The plasma density, the velocity parallel to the magnetic field and the ion’s pressure are evaluated from the velocity moment of the ion’s distribution function. The MHD equilibrium is constructed by the HINT code without assumption of the existence of nested magnetic surfaces. The central beta value is assumed to be 7.5%. It is found that the linear growth rates of the resistive ballooning modes obtained from the kinetic MHD model are smaller than the linear growth rates obtained form the MHD model. In the radial mode structure of the pressure obtained from the kinetic MHD model, the amplitude of the ion pressure is about half of the amplitude of the electron pressure due to the ion’s finite orbit width (FOW) effects. For the saturated state of the MHD instabilities, although the central pressure decreases for both the MHD model and the kinetic MHD model, the decrease of the central pressure for the kinetic MHD model is smaller than that of the central pressure for the MHD model. Since the MHD instabilities are the resistive modes, the stabilizing effects of the ion kinetic effects is expected to be stronger for the experimental high magnetic Reynolds number so that the core crush may be suppressed.

Speaker: Dr Masahiko Sato (National Institute for Fusion Science)

Summary Slides Summary_slide_TH_P5-25.pdf (Protected)

424 Localized modulation of turbulence by magnetic islands on HL-2A tokamak

Magnetic islands formed in magnetically confined plasmas have significant influence on plasma profiles and cross-field transport, and can even cause plasma disruption [1,2]. However, observations of internal transport barriers near the rational magnetic surface suggest the importance of magnetic islands in plasma confinement via increase of flow shear at the island boundary [3,4]. In recent years the multi-scale interaction between large-scale modes and micro-scale turbulence has been found to play an important role in regulating turbulent transport and eventually form the low to high mode transition [5,6]. In this paper, modulation on turbulent electron temperature fluctuations and density fluctuations by an m/n =1/1 tearing mode island was observed in the core plasma region of the HL-2A tokamak. High tempo-spatial resolution two-dimensional images of temperature fluctuations show the first evidence that the turbulence modulation occurs only when the island width exceeds a certain threshold value (6.4 cm) and the modulation is localized merely in the inner half area of the island due to significant alteration of local profiles and turbulence drives. Evidence also reveals that for large islands turbulence spreading takes place across the flat temperature of the O-point at the inner half island region, whereas in the outer half area the small temperature gradient drives a low level of temperature fluctuations. [1] G. Fiksel et al 1995 Phys. Rev. Lett. 75 3866. [2] W. Suttrop et al 1997 Nucl. Fusion 37 119. [3] K. Ida et al 2002 Phys. Rev. Lett. 88 015002. [4] E. Joffrin et al 2003 Nucl. Fusion 43 1167. [5] A. Fujisawa et al 2004 Phys. Rev. Lett. 93 165002. [6] I. Shesterikov et al 2013 Phys. Rev. Lett. 111 055006.

Speaker: Min Jiang (Southwestern Institute of Physics)

M Jiang ppt P5-4.pdf

425 Negative Triangularity Effects on Tokamak MHD Stability

Recently, discharges with negative triangularity were created in the DIII-D tokamak. These discharges exhibited the H-mode-level confinement features with L-mode-like edge behavior without ELMs (M.E. Austin et al., Bull. Am. Phys. Soc. vol. 62 (2017)). This led us to extensively examine the MHD stability of negative triangularity tokamaks. Using the numerically reconstructed experimental equilibrium, our computation confirmed the stability of the beta normal of 2.6 achieved in DIII-D experiments against low-n MHD kink modes. In parameter variations outside the experimental values, we surprisingly found that the negative triangularity configuration can actually achieve even higher beta normal than the positive triangularity case in certain cases. We used the VMEC equilibrium code to construct the equilibria, with the bootstrap current included from the Sauter formula. The stability was investigated using the AEGIS code, supplemented by the DCON code. Indeed, our calculations show that the negative triangularity configuration with low bootstrap current fraction and usual equilibrium profiles is usually not good for MHD stability. However, we found that the negative triangularity configuration leads to a lower safety factor value especially near the edge. That motivates us to reduce the Ohmic current and increase bootstrap current fraction. Surprisingly, it is found that some higher bootstrap fraction, high poloidal beta, negative triangularity cases can have much higher beta normal limit than 4 Li, while the positive triangularity case is limited by 4 Li as usual. We found that the negative triangularity favors the peak pressure profiles; while the positive triangularity the broad pressure profiles. This leads us to conclude that the negative triangularity tokamak can be more attractive than the positive triangularity case for steady-state confinement in the advanced tokamak scenario from the point of view of low n MHD stability.

Speaker: Linjin Zheng (University of Texas at Austin)

Zheng.L-TH-S.-summary.pdf

426 Nonlinear Dynamics of Tearing Mode Driven by Static and Rotating External 3D Fields

The interaction of a locked tearing mode with a non-axisymmetric control field is found to be in good qualitative agreement with predictions of a nonlinear resistive MHD model [1]. Locked tearing mode islands often lead to disruptions in tokamaks. However, experiments have shown that unlocking and rotation of the island by a rotating control field (CF) can postpone or prevent a disruption [2]. The dynamics of this control has been modeled with the "AEOLUS-IT" code [1] in both tearing stable and unstable plasmas. In the tearing stable plasma, a static error field (EF) drives the island growth, which is successfully stabilized by the CF. Even in tearing unstable plasmas, the CF is predicted to reduce the nonlinearly saturated island size. Model predictions of two distinct regimes of plasma response, characterized as standing-wave and traveling-wave, are in good qualitative agreement with DIII-D observations. These results are an important step toward predictive understanding of this new approach to tearing mode control and disruption avoidance.

[1] S. Inoue et al., Nucl. Fusion 57, 116020 (2017); Plasma Phys. Control. Fusion 60, 025003 (2018).

[2] M. Okabayashi et al., Nucl. Fusion 57, 016035 (2017).

Speaker: Dr Shizuo Inoue (QST)

IAEA_2018_summary_rev_7_reduced_size_si.pptx

427 Nonlinear evolution of multi-helicity neoclassical tearing modes in HL-2A low rotation plasmas

In HL-2A low rotation and relatively low density plasmas, the critical threshold of the intrinsic error field penetration will be decreasing. And the multi-helicity islands can be seeded by the non-axisymmetric error field penetration, and lead to the change of rotation profile, enhanced transport or even disruption. Sheared flow arising from momentum injection can suppressed the coupled islands. For understanding the experimental results, numerical modelling will be carried out by means of reduced magnetohydrodynamic simulations. The results provide important evidence for NTMs stability predictions and their nonlinear dynamic in the low flow plasmas, such as ITER.

Speaker: Dr Xiaoquan JI (Southwestern Institute of Physics, Chengdu 610041 China)

428 Nonlinear MHD simulations of Quiescent H-mode in ASDEX-Upgrade and ITER

Both nonlinear simulations and experiments of DIII-D QH-mode plasmas show that E×B rotation plays an essential role for obtaining the QH-mode. However, the mechanism for the QH-mode onset and its saturation, the influence of other rotation flows such as neoclassical flow, diamagnetic flow as well as the influence of resistive wall still remains unclear due to the complexity of the physics of edge plasma non-linear MHD stability. Hence, understanding the physics mechanisms leading to the saturation of the EHO in QH-mode plasmas and the role of plasma rotation in EHO behaviour is an important issue to support experiments in ASDEX-Upgrade to access the QH-mode regime and to assess whether the QH-mode could be a viable alternative regime for an ITER high Q scenario. In this work nonlinear MHD simulations of ASDEX-Upgrade QH-mode plasma #17686 have been performed with the non-linear MHD code JOREK for the first time. The low-n kink-peeling modes (KPMs) have been found unstable and grow to a saturated level in the edge of the ASDEX-Upgrade QH-mode plasma. This leads to a helical structure on the plasma density, which is associated with the 3-D localisation of the KPM at the separatrix in the toroidal and poloidal direction. The influence of neoclassic rotation, E×B rotation and diamagnetic rotation on QH-modes have been investigated to understand the physics mechanisms leading to the QH-mode behaviour and to support the achievement of QH-mode plasmas in the ASDEX-Upgrade device. The simulations for ITER Q=10 scenario have been extended to include n=0-5 modes and n=0-10 modes and including a resistive wall. The results show that the inclusion of a resistive wall has a significant influence on the non-linear evolution of KPMs in ITER plasma while this effect is found to be small in QH-mode simulations of DIII-D plasmas. The simulations show E×B rotation/shear plays an important role for ITER high Q plasmas to enter and remain in the QH-mode regime. The results of these simulations will be evaluated in the paper to determine whether this regime is an option for high fusion performance operation at the specific characteristics of ITER plasmas.

Speaker: Dr FENG LIU (Université Côte d’Azur)

summary.pdf

429 Nonlinearly Saturated Ideal Magnetohydrodynamic Equilibrium States with Periodicity-Breaking in Stellarators

The relaxation of the constraint of periodicity imposed by the external confining magnetic field coils in a nominally 4-field period Helias Advanced Stellarator configuration produces weak periodicity-breaking deformations of the plasma. The corrugations are driven by the interaction of the pressure gradient with the magnetic field line curvature and correspond to saturated ideal magnetohydrodynamic interchanges with a mode structure dominated by nonresonant $m=1$, $n=\pm 1$ Fourier components. Very similar low order mode number oscillations are observed in the 4-field period TJ-II Heliac stellarator. The conditions of quasi-isodynamicity of the Helias reactor system investigated are not significantly altered by the periodicity-breaking distortions.

Speaker: Dr Daniel López-Bruna (EsLNF)

COOPER_IAEA18_poster.pdf

Cooper_IAEA2018.pdf

SummarySlide_P5-28.pdf

430 NTM Excitation by Sawtooth Crashes and the Suppression of their Onset by Resonant Magnetic Perturbation

Neoclassical tearing modes (NTMs) can degrade plasma confinement or even lead to disruptions in existing tokamak discharges. To understand their triggering mechanism by sawtooth crashes and the effect of error fields or externally applied resonant magnetic perturbations (RMPs) on their onset remain to be important for ITER or a fusion power plant. In this paper these two issues are studied numerically based on the two-fluid equations, using ASDEX Upgrade experimental parameters as input. (a) **Triggering of NTMs by sawtooth crash**: Numerical calculations have been carried out to study the triggering of NTMs by sawtooth crashes. In toroidal geometry, the nonlinear harmonics of the m/n=1/1 mode, the 2/2 component, can have a large amplitude during the sawtooth crash and possibly drive a 3/2 seed island via toroidal mode coupling, where m (n) is the poloidal (toroidal) mode number. As expected, it is found that the onset of the 3/2 NTM is most effective for large sawtooth amplitudes, high plasma beta value and low relative frequency between these two modes. The 3/2 magnetic perturbations first have the feature of an ideal mode across the q=3/2 surface and show a tearing character only later in time. The latter is in very good agreement with experiments. The observed immediate increase of the 3/2 magnetic signal after a sawtooth thus represents an ideal magnetic perturbation rather than a magnetic island. (b) **Effect of RMPs on NTMs**: In several tokamak experiments a stabilization of rotating magnetic islands by static RMPs of moderate amplitude have been observed. This is consistent with our numerical results showing that a magnetic island can be suppressed by a static RMP of the same helicity in a certain range of RMP amplitude, if the local perpendicular electron fluid velocity at the resonant surface is sufficiently large. Due to the electron diamagnetic drift, the mode stabilization effect by RMPs is much stronger in the two-fluid case than in the single fluid case. The mechanism only works for moderate RMP amplitudes. In case of a too large RMP amplitude, the island growth is supported by the RMPs, resulting in a large locked magnetic island.

Speaker: Prof. Sibylle Günter (Max-Planck-Institut für Plasmaphysik)

iaea2018.summary.b.pdf

431 Numerical Relaxation of a 3D MHD Taylor-Woltjer State Subject to Abrupt Expansion

Rupak Mukherjee, Rajaraman Ganesh Institute for Plasma Research, HBNI, Gandhinagar, Gujarat, India, 382428. ganesh@ipr.res.in Since the advent of Taylor-Woltjer theory [1,2], it has been widely believed that situations with perfectly conducting boundaries and near ideal conditions, the final state of MHD system would be force-free Taylor-Woltjer states defined as curl B = alpha B with alpha as a constant and B is the magnetic field defined over a volume V. These states are of fundamental importance in fusion plasmas [3]. More recently, several new MHD models have been proposed – for example Reduced Multi-region relaxed MHD [4] and arbitrary scale relaxation model to Taylor-Woltjer state [5] to mention a few. In the present work, we use a 3D compressible MHD solver in cartesian geometry which can handle conducting or periodic as well has mixed boundary conditions to investigate numerically the arbitrary scale relaxation model proposed by Qin et al [5]. For this purpose, we consider two volumes V_init and V_final. We load the 3D MHD solver in the limit of zero compressibility with a Taylor-Woltjer state B_init(x,y,z,t=0) and let it again a numerical evolve with conducting boundaries at V_init to make sure that we have obtained a numerically steady Taylor-Woltjer state for volume V_init. Followed by this procedure, we ``suddenly'' relax the boundaries to a new volume V_final, such that V_init < V_final and evaluate whether or not the system attains quasi-steady state. Details of the numerical method used, the protocol followed, the expansion technique and the novelty of this numerical experiment and details of our results will be presented. References [1] J. B. Taylor, Phys. Rev. Lett, 33, 1139 (1974) [2] L. Woltjer, Proc. Nat. Acad. Sci U.S.A , 44, 489 (1958) [3] J. B. Taylor, Rev. Mod. Phys. 58, 741 (1986) [4] S R Hudson et al, Phys. Plasmas, 19, 112502 (2012) [5] H. Qin et al, Phys. Rev. Lett. 109, 235001 (2012)

Speaker: Mr Rupak Mukherjee (Institute for Plasma Research)

summary_slide_Rupak.pdf

432 Peculiar Properties of Disruptions on T-10 Tokamak at Different Edge Safety Factor Values

One of the main goals of researching global plasma disruptions is to find a way to prevent the formation of runaway electron beams, after the plasma current disruption. A possible way to solve this problem is to generation of strong MHD perturbation during current decay. The experimental study of density limit disruption on tokamak T-10, for study dependency a duration of plasma current decay t95 (from 100% to 5% of plasma current on quasi state stage of discharge) from edge safety factor q_a was curry out. As result, it was found that, if value qa integer or half-integer than duration of plasma current decay is high increase, up to 100-115 ms. The increased duration of current decay is uniquely relate with qa, what showed in experiments where changing of the value of toroidal field and plasma current with constant qa do not lead to changing character and duration of current decay. From the available experimental data it follows that during slow current decay while plasma column move to high field side, one at a time multiple extensions and contractions by minor radius are occur. The moment of time when the plasma column expands is correlated with peaks on the loop voltage and with peaks on the MHD perturbation of poloidal magnetic field. The main character feature of disruption with a slow current decay is absence of hard X-rays. Thus, from available experimental data, we can conclude, that during a slow current decay, high MHD activity lead to prevent the formation of runaway electron beams.

Speaker: Dmitriy Ryzhakov (RuKurchatov)

Ryzhakov-summary-slide.pdf

433 Pedestal dynamics in inter-ELM phase on HL-2A tokamak

Streamer, as well as zonal flow is a very challenging subject since it is expected to have significant effects on confinement in high temperature plasmas. Theoretical simulation predicts that streamers originate from the nonlinear development of turbulence driven by electron and ion temperature gradient. In experiments, few works have reported the streamer observation only up to now, and detailed analysis of the streamer dynamics is still a lack, in spite of its importance in the understanding of plasma confinement in toroidal fusion devices. Here we report the first observation of streamer formation in the HL-2A edge plasmas in inter-ELM phases. The streamer is developed from turbulence via a quasi-coherent mode which interacts with and modulates ambient turbulence, induces an inward particle flux, and plays an essential role in the pedestal dynamics in the inter-ELM phases. Detailed results on the streamer characteristics and its role in triggering the ELM will also be presented.

Speaker: Dr Jun Cheng (Southwestern Institute of Physics)

Manuscript_IAEA_v2.pdf

434 Physics and Engineering Design for Chinese First Quasi-axisymmetric Stellarator(CFQS)

The Chinese First Quasi-axisymmetric Stellarator (CFQS) is a joint project of international collaboration. It is designed and fabricated by Southwest Jiaotong University (SWJTU) in China and National Institute for Fusion Science (NIFS) in Japan. The target parameters of CFQS are as follows: toroidal periodic number N = 2, major radius R = 1.0 m, aspect ratio R/a = 4.0 and magnetic field strength B=1.0 T. Via the scan of major radius (1.0m-1.5m) and aspect ratio (3-5), the target parameters of CFQS configuration are determined by comprehensively considering physics and engineering constrains. The toroidal periodic number N = 2 is selected, which guarantees to form the tokamak-like configuration. A low aspect ratio is one of the important features of the CFQS design because of the advantage of compactness and economy, which could be used in future commercial reactors. From the core region to the edge, the vacuum rotational transform is designed between 2/6 and 2/5 which is advantageous to avoid low-order rational surfaces. In addition, the presence of a magnetic well is capable to stabilize the MHD and reduce the island widths. In order to achieve the target magnetic configuration, a modular coil system is necessary to be designed to reproduce the plasma boundary. According to the Neumann boundary condition, the accuracy of the magnetic configuration induced by the coil system depends on the normal component of the magnetic field on the plasma boundary. Via the minimization of the normal component of the magnetic field on the plasma boundary, the modular coil geometry is optimized. Meanwhile, the engineering constraints are also taken into account, which are the minimum interval between adjacent coils and the maximum curvature. This optimization process is accomplished by the NESCOIL code. The Mercier stability, ballooning stability and neoclassical transport were also calculated to evaluate the property of the CFQS configuration. The MHD equilibrium of the configuration is almost stable up to beta = 1%. The neoclassical transport in the CFQS is expected to be less than that in 1/v regime in the W7-X.

Speaker: Prof. Yuhong Xu (Southwest Jiaotong University)

IAEA2018_1 slide PPT_Yuhong_XU.pdf

435 Plasma confinement and pedestal dynamics responses to impurity seeding in HL-2A H-mode plasmas

In HL-2A H-mode plasmas, the confinement and pedestal response to impurity seeding have been recently investigated [1]. It has been observed that a broadband electromagnetic (EM) turbulence can be driven by peaked impurity density profile at the edge plasma region, and governed by double critical gradients of the impurity density [2]. In addition to the spontaneously accumulated impurity, the electromagnetic turbulence and quasi-coherent EM modes can also be excited by externally seeded impurity in HL-2A [3]. The excited pedestal instabilities can play an important role in the regulation of the pedestal turbulent transport. More recently, the SMBI system has been used for gas impurity seeding (Ar, Ne, etc), which is beneficial for forming an edge radiation layer and avoiding impurity core accumulation. With pure impurity injection, it has been observed that the ELM frequency is increased and the H-mode plasma confinement is improved with a broadened and steepened density pedestal. For the D2 SMBI, it can mitigate ELMs as observed in several devices. Thus, a newly developed SMBI system with mixture impurity gas (D2+Ne or D2+Ar) is used in HL-2A. The impurity gas is mixed with plasma work gas D2 by different ratios. The dedicated experiments show that the ELM behavior, plasma confinement and pedestal structure are varied with the ratio of the impurity mixture. It has been found that large ELMs are replaced by very small bursts with 30% Ne-SMBI seeding. The SMBI pulse length is 2ms. The large ELM is suppressed for a period of about 50ms. Meanwhile, the divertor heat load is significantly reduced. When the ratio changed to 10%, the confinement response is similar to that of the D2 SMBI. However, when the gas was changed to pure Ne, the ELM frequency was increased and the confinement was enhanced. The results suggest that both the pedestal structure and pedestal stability are modified with the amount of impurity and impurity species. Experimental observations indicate that there is an optimal impurity ratio for heat load control. The results suggest that pedestal dynamics and heat loads can be actively controlled by exciting pedestal instabilities and forming a steady edge radiation layer. [1] W.L. Zhong et al 2017 Plasma Phys. Control. Fusion 59 014030 [2] W.L. Zhong et al 2016 Phys. Rev. Lett. 117 045001 [3] Y.P. Zhang et al 2018 Nucl. Fusion 58 04601

Speaker: Dr Wulyu Zhong (CnSWIP)

436 Plasma equilibrium reconstruction of JET discharges using the IMAS modelling infrastructure

The reconstruction of Tokamak plasma equilibrium is a fundamental step in the understanding of fusion plasma physics since it sets the starting point for all subsequent plasma modelling applications and experimental data interpretation. The verification and validation of the numerical codes used to reconstruct plasma equilibrium, using as many available input experimental data e.g. magnetic field or flux measurements, density and temperature diagnostics and polarimetry diagnostics, is essential both for physics model interpretation and when qualifying and extrapolating for ITER. In the framework of the EUROfusion Work Package on Code Development for Integrated Modelling, a scientific Kepler [1] workflow for the reconstruction of Tokamak plasma equilibrium was prototyped, using the ITER Integrated Modelling and Analysis Suite (IMAS) [2,3]. The workflow can seamlessly use any sort of data from Tokamak experiments and call reconstruction codes such as EQUAL [4], CLISTE [5], EQUINOX [6] and SDSS [7], all using the same physics and engineering data ontology and methods for accessing the data. In this work, we address plasma equilibrium reconstructions on dedicated JET plasma discharges, performing a code benchmark using, at first, magnetic data only and subsequently considering also other constrains such as polarimetry (Stokes vector based or Motional Stark Effect). First results with magnetic only give good qualitative and quantitative agreement between the codes. References [1] https://kepler-project.org/ [2] S.D. Pinches et al., Proc. 26th IAEA FEC, Kyoto, Japan, 2016, paper TH/P2-14. [3] F. Imbeaux, et al, Nuclear Fusion 55 (12), 123006, (2015) [4] W. Zwingmann, Nucl. Fusion 43 (2003) 842 [5] P. J. McCarthy, Phys. Plasmas 6, 3554 (1999) [6] B. Faugeras et al., Plasma Phys. Control Fusion 56 (2014) [7] R. Coelho et al, Fusion Sci. Technol. 69, 611 (2016)

Speaker: Dr Rui Coelho (Instituto de Plasma e Fusão Nuclear / Instituto Superior Técnico)

Coelho_IAEA_summary_slide_v2.pdf

437 Plasma transport in linear and helical multiple-mirror systems

The challenge of creation of an open trap with the reactor-grade plasma is achievable if such trap will use specialized sections of the magnetic system for suppression of particle and energy losses along the magnetic field. Currently, two new experimental devices are under construction in the Budker Institute for studies of physics of plasma confinement in magnetic systems with multiple-mirror configurations. Linear topology of the traps enables early start of experiments with plasma before the completion of the magnetic and vacuum systems. In the paper, we will report experimental results on the transport of a low-temperature start plasma flow through a section with a multiple-mirror magnetic field as well as the direct comparison with the case of solenoidal magnetic field. In the final configuration of GOL-NB, that plasma stream will be used as the target for the capture of heating neutral beams. In 2017, new SMOLA helical multiple-mirror trap achieved the first plasma. In this trap, plasma rotation is used for creation of moving magnetic mirrors in the rotating frame of reference. An active plasma pumping by the moving magnetic mirrors can deliver an exponential dependence of the confinement efficiency on the system length. Modification of the plasma flow profile at helical mirror confinement was demonstrated in the experiment. Main results from the first experimental campaign will be discussed.

Speaker: Prof. A.V. Burdakov (Budker Institute of Nuclear Physics SB RAS, Novosibirsk, Russia)

Summary slide Burdakov.pptx

438 Real-time control system of neoclassical tearing modes in the HL-2A tokamak

The stability and performance of tokamak plasmas are routinely limited by various magneto-hydrodynamic (MHD) instabilities, such as neoclassical tearing modes (NTMs). This paper presents a rather simple method to control the NTMs in real time (RT) on a tokamak, including the control principle of feedback approach for RT suppression and stabilization for the NTMs. The control system combines Mirnov, electron cyclotron emission (ECE) and soft X-ray (SXR) diagnostics used for determining the NTM positions. A methodology for fast detection of 2/1 or 3/2 NTM positions with 129x129 grid reconstruction within 0.6 ms is elucidated. The forty poloidal angles for steering ECRH/ECCD launcher are used to establish the alignment of antenna mirrors with the center of the NTM and to ensure launcher emission intersecting with the rational surface of a magnetic island. Pilot experiments demonstrate the RT control capability to track the conventional tearing modes (CTMs) on HL-2A tokamak. The 2/1 CTMs have been suppressed or stabilized by the ECRH power deposited on site or with steerable launcher. The total time to scan fully poloidal cross section is ~200 ms with spatial resolution of ~0.5 cm. The magetic island is determined by an ECE diagnostic system of 60 channels with spatial resolution about 1 cm. So far, we are improving the NTM control system. The total time will be decreased to ~50 ms from ~200 ms, which is enough to control any NTMs. Further dedicated studies on reliability of the actual NTM control scheme and minimum power requirements will be demonstrated in the Spring's experimental campaign in 2018.

Speaker: Dr Longwen Yan (Southwestern Institute of Physics)

439 Resistive Wall Mode physics and control challenges in JT-60SA high βN scenarios

The superconducting tokamak JT-60SA is being built in Naka (Japan) under the Broader Approach Satellite Tokamak Programme jointly by Europe and Japan, and under the Japanese national programmme. JT-60SA has an important supporting mission for the development of fusion energy: designed to achieve long pulses (100 s) and break-even equivalent plasmas, challenging high $\beta$ operation beyond the no-wall limit. It will help in both the exploitation of ITER and in the definition of an optimized DEMO design. The device will be equipped with off-axis Negative-NBI at 0.5 MeV beam energy, allowing current profile tailoring for Advanced Tokamak scenarios with fully non-inductive current drive. The focus of the work is set on high β N scenarios, in which kink-like instabilities (e.g. one or more RWMs) are potentially unstable and possibly lead to disruptions. In the framework of a joint European-Japanese collaboration, coordinated effort on MHD stability and control modeling is ongoing for the safe realization and exploitation of high $\beta_N$ plasmas. These scenarios offer a great opportunity to test and verify present models of RWM physics. The drift-kinetic damping model in particular will be considered in the present work, with a stability study in Scenario 5.1 – like plasmas carried out with MARS-F/K. The challenge of active control is also addressed, taking advantage of the set of RWM Control Coils that JT-60SA will have. A dynamic simulator, based on the CarMa code, has been developed for feedback control modeling. A demonstration of this tool is given in one of the aforementioned plasmas, showing potential applications, results and latest developments.

Speaker: Dr Leonardo Pigatto (ItRFX)

Pigatto_IAEA2018_summarySlide.pdf

440 Role of NTV particle flux in density pumpout during ELM control by RMP

Edge localized modes (ELMs) release large bursts of heat and particle flux to the plasma facing components in tokamaks, potentially causing significant material erosion in future devices such as ITER. Externally applied three-dimensional (3D) resonant magnetic perturbations (RMP) have been experimentally demonstrated to be effective in tailoring these ELM bursts. A significant yet not well understood phenomenon is the density pumpout effect caused by the RMP field. Understanding physics mechanisms associated with density pumpout is critical to: (i) understand the ELM control itself; (ii) understand RMP induced plasma performance degradation; (iii) provide guidance to ELM control design in ITER. This contribution reports toroidal modelling results of RMP induced density pumpout, based on a self-consistent quasi-linear model implemented into the MARS-Q code. The model combines the resistive plasma response to 3D fields, with the axi-symmetric toroidal momentum and radial particle transport equations. In particular, the radial particle flux includes contributions from that associated with neoclassical toroidal viscosity (NTV). We found that the resonant NTV particle flux, which is significantly enhanced due to Landau resonance between the applied perturbation and the precessional drifts of trapped thermal particles, provides a significant outward particle flux near the pedestal top, where the ExB rotation velocity is small or even crossing zero. Initial value simulations, lasting longer than the momentum and particle confinement times, demonstrate the important role of the NTV particle flux in causing a large fraction of density pumpout. The work was supported by US DoE Office of Science under Contract DE-FG02-95ER54309 and DEFC02-04ER54698.

Speaker: Dr Yueqiang Liu (General Atomics, PO Box 85608, San Diego, CA 92186-5608, USA)

Summary_slide_Liu_v2.pptx

441 Roles of RMP-induced Changes of Radial Electric Fields in ELM Suppression

Resonant magnetic perturbations (RMPs) can be used to mitigate or fully suppress the harmful Edge Localized Modes (ELMs). In DIII-D, the ELM suppression is observed to be correlated with the enhanced particle and heat transport near the pedestal top. Initial simulations using Gyrokinetic Toroidal Code (GTC) show that the kink responses to the 3D RMP have little effect on the growth rate of electromagnetic kinetic-ballooning mode and on the turbulent transport and zonal flow damping in electrostatic turbulence [Holod, et. al., Nuclear Fusion 57, 016005 (2017)]. On the other hand, fast RMP modulation experiments in DIII-D tokamak show that the turbulent poloidal velocity changes in phase with the modulated RMP current, suggesting that the RMP may modify the local radial electric field $E_r$.

Here we report from GTC simulations that reduced $E_r \times B$ shearing rate due to the RMP leads to the much stronger driftwave instability in the outer edge and outward turbulence spreading, resulting in a larger turbulent transport on the pedestal top in the DIII-D experiments. Simulation results are consistent with experimental observations of increased turbulence and transport near the pedestal top during RMP-induced ELM suppression. Furthermore, GTC simulations of neoclassical transport show that the electron flutter motion due to the RMP islands introduces a radial particle flux that is not strong enough to directly provide the measured enhancement in the transport, but may contribute to the observed change in the radial electric field. Finally, electrostatic turbulence simulations with adiabatic electrons show no significant increase of the saturated ion heat conductivity in the presence of RMP-induced islands. However, electron response to zonal flow in the presence of magnetic islands and stochastic fields can drastically increase zonal flow dielectric constant for long wavelength fluctuations. Zonal flow generation can then be reduced and the microturbulence can be enhanced greatly.

Speaker: Zhihong Lin (UC Irvine)

Summary IAEA_TH-P5-7-LShi_Summary.pdf

442 Sandpile modelling of pellet pacing in fusion plasmas

Sandpile models have been used to provide simple phenomenological models without incorporating the detailed features of a fully featured model. The Chapman sandpile model (Chapman et al *Physical Review Letters* 86, 2814 (2001)) has been used as an analogue for the behaviour of a plasma edge, with mass loss events (MLEs) being used as analogues for (and anagrams of) ELMs. Here we modify the Chapman sandpile model to form comparisons with pellet pacing, which is used to reduce or eliminate ELMs. We use two different versions of the Chapman model, one in which the system is allowed to relax following an avalanche before further sand ($dx$) is added (classic model), and one in which further sand is added while an avalanche is propagating (running model). For this purpose, we modify the models in two different ways. First, we increase the amount of sand added at each time step, so that we move from the low driving model typically used in sandpile modelling to a high driving model. Second, we add 'bursts' of sand at intervals which are synchronised to MLEs in the sandpile, by way of comparison with pellet injection in a fusion plasma. We then analyse the behaviour of the sandpile in these new models, focusing on changes in the total system size, and on the maximum MLE size (by way of analogy with maximum ELM size). We observe that at low $dx$, potential energy ($E_p$) varies with $dx$ in the running model, while $E_p$ remains constant in the classic model. Probability distribution functions of waiting times between MLEs are identical for common values of $dx/Z_c$, as $dx$ and the critical gradient, $Z_c$, are varied. Waiting times are observed to scale inversely with fuelling in the classic model, consistent with the observation that $E_p$ is unchanged, such that MLEs depend on the amount of sand in the system, and not on the rate at which the sand builds up. Analysis of $E_p/E_{p Max}$ against $dx/Z_c$ for increasing $dx$ shows that step changes occur, often at integer ratios. An heuristic explanation is suggested for this behaviour. At very high driving, the final state of the running model can be determined analytically given the value at cell $n=1$. At extremely high driving, $E_p$ increases with $dx$ in the classic model, as the cells at the edge do not exceed the critical gradient, while those at the core do exceed the critical gradient.

Speaker: Mr Craig Bowie (Australian National University)

FEC2018_Bowie_Hole_summary_slide.pdf

443 Simulation of the internal kink mode in visco-resistive regimes

The (m=1, n=1) internal kink instability plays an important role in the dynamics of a tokamak discharge and is responsible for the occurrence of sawtooth oscillations. Many experimental observations show that plasma rotation can strongly influence the stability properties of sawtooth oscillations. Past theoretical flow studies to understand such stabilization have been done in the low viscosity regimes. Viscosity can be high in tokamaks due to enhancements from turbulent effects. We investigate the stability of the (1,1) mode in the presence of sheared flows over a range of viscosity regimes using the CUTIE code for both RMHD and two-fluid models. Initially, we use the RMHD version of CUTIE and systematically examine the effects of several kinds of sheared flows on the (1,1) mode, namely axial, poloidal and combinations of both types of flows in the linear and the nonlinear regimes. In the absence of flow and for low Prandtl numbers we observe that the growth rate scalings with resistivity and viscosity agree with past theoretical results. However, as we increase the viscosity further, the growth rate scaling changes significantly. It shows that high viscosity can strongly influence the linear growth rate of the modes. We find that in the presence of an axial flow, the stabilizing influence of viscosity is enhanced and can lead to a complete stabilization of the m = 1 visco-resistive mode at high Prandtl numbers. In the nonlinear regime, for axial flows, the saturation level of the mode decreases at a higher viscosity compared to the case of no flow but slightly increases at lower viscosity. Similar results are found for the poloidal flow case. In the case of helical flows at high viscosity, there is a significant change in the nonlinear saturation level depending on the flow helicity. We have continued the above studies into the two-fluid regime and found diamagnetic drift stabilization of the (1,1) mode i.e. the growth rate of the (1,1) mode reduces with an increase in the density gradient. The nonlinear evolution of the mode in the presence of imposed shear flows also shows distinct differences from the RMHD results due to the presence of two-fluid effects.

Speaker: Mr Jervis Mendonca (Institute for Plasma Research Gandhinagar INDIA)

sumslide_jmendonca_thP5-21_FEC18.pdf

444 Stability and Confinement Studies in the Gas Dynamic Trap

Interest to magnetic mirrors went missing in the 1980's because of three key problems: magnets' complexity, micro-instabilities, and low temperature of plasma. However, researches on the Gas Dynamic Trap (GDT) device at the Budker Institute of Nuclear Physics demonstrates the possibility to overcome these difficulties. Confinement of plasma with high energy density have been performed on GDT device with simple circular coils. “Vortex confinement” have been implemented to suppress the radial losses induced by flute-like MHD instability inherent to axially symmetric devices. This technique allowed reaching local plasma beta close to 0.6. The auxiliary microwave heating on electron cyclotron resonance (ECR) frequencies raised the electron temperature up to 0.9 keV near the device axis. Alfven ion-cyclotron (AIC) instability have been observed, but not affected to the plasma power balance. The proposed report is dedicated to next three topics. The first is optimization of the “vortex confinement” in presence of ECR heating. Introducing the additional “vortex” layer inside the existing one allows extending high-temperature phase behind the atomic beams turn off time. The second is definition of critical parameters for the diverter. It was shown, that the critical wall position corresponds to expansion ratio of magnetic field $K_{crit} \sim 40$. This value is in a reasonable agreement with a simple theoretical model and remains constant in the range of electron temperature 25 - 700 eV. The neutral gas in the diverter does not affected the discharge until its density exceeded an order of magnitude the plasma density. The third is study of unstable modes. In addition to AIC, the new type of oscillations are observed at the range of tens of ion-cyclotron frequencies. It was preliminary identified as Drift-Cyclotron Loss-Cone instability.

Speaker: Dr Vadim Prikhodko (Budker Institute of Nuclear Physics SB RAS)

Poster.pdf

Summary slide.pdf

445 Suppression and destabilization of ion fishbone activities on HL-2A

Magneto-hydrodynamic (MHD) instabilities in hot plasmas can strongly limit the operational parameter space of a fusion reactor. Their stabilization, suppression and active control have therefore attracted much attention, in particular with regard to expansion of the operational space, enhancing the fusion performance and decreasing the energetic particle losses in both present-day fusion devices and future devices with burning plasmas. Control of multiple instabilities including sawtooth, neoclassical tearing mode (NTM), resistive wall mode (RWM), edge localized mode (ELM), Alfven eigenmode as well as energetic-particle mode (EPM), has been successfully achieved, to various degrees, by different means such as the radio frequency wave heating/drive, the three-dimensional magnetic perturbations, and so on, in many fusion devices. On the other hand, understanding of both the control and physics of these instabilities, in many cases, is still far from complete, and remains area of active research. The fishbone mode is one of these key instabilities, which is destabilized by a population of energetic particles. In burning plasmas, energetic alpha particles, though being a minority species, carry a large fraction of the plasma kinetic energy, and can potentially drive the fishbone instability. The fishbone has also been proposed as a possible scheme for ash removal and burn control, as well as tungsten-impurities removing from the plasma core on ITER. In this paper the recent progress of ion fishbone activities will be present on HL-2A. Firstly, it will be reported the stabilization of m/n=1/1 fishbone by ECRH. The stabilization of m/n=1/1 fishbone depends not only on the injected power but also on the radial deposition location of ECRH, and the instability can be completely suppressed when the injected ECRH power exceeds certain threshold. Analysis by the fishbone dispersion relation, including the resistive effect, suggests that the magnetic Reynolds number plays a key role in the mode stabilization. Secondly, it will be introduced the destabilization of m/n=2/1 fishbone. The evolution of m/n=2/1 fishbone is related to mode rotation reverse. The excitation mechanism of m/n=2/1 fishbone will also be discussed, namely what’s the result of the kink or tearing mode interacting with circulating or trapped EPs.

Speaker: Dr Wei Chen (Southwestern Institute of Physics, P.O. Box 432 Chengdu 610041, China)

IAEA_EP.pptx

446 The Effect of Pressure Anisotropy on Ballooning Modes in Tokamak Plasmas

Edge Localised Modes (ELMs) are thought to be caused by a spectrum of magnetohydrodynamic instabilities, including the ballooning mode. While ballooning modes have been studied extensively both theoretically and experimentally, the focus of the vast majority of this research has been on isotropic plasmas. The prevalence of pressure anisotropy in modern tokamaks thus motivates further study of these modes. This paper presents a numerical analysis of ballooning modes in anisotropic equilibria. The investigation was conducted using the newly-developed codes HELENA+ATF and MISHKA-A, which adds anisotropic physics to equilibria and stability analysis. We have examined the impact of anisotropy on the stability of an n=30 ballooning mode, confirming results conform to previous calculations in the isotropic limit. Growth rates of ballooning modes in equilibria with different levels of anisotropy were then calculated using the stability code MISHKA-A. The key finding is that the level of anisotropy had a significant impact on ballooning mode growth rates. For T⊥ > T||, typical of ICRH heating, the growth rate increases, while for T⊥ < T||, typical of neutral beam heating, the growth rate decreases. For levels of anisotropy observed in JET and MAST plasmas, we expect the impact on growth rates for realistic configurations to be significant. An important conclusion is the possibility that higher ELM-free performance might be achieved by increasing p||/p⊥ in the pedestal region.

Speaker: Dr Matthew John Hole (Australian National University)

FEC2018_Hole_summary_01.pdf

447 Thermal energy confinement at the Globus-M spherical tokamak.

The presentation is devoted to the overview of thermal energy confinement time study at the compact spherical tokamak Globus-M. Globus-M has major radius R = 0.35 m and minor radius a = 0.21 m (R/a ~ 1.6). The lower-null magnetic configuration is characterized by moderate elongation k~1.9 and triangularity δ~0.35. The present study was performed in both OH and NBI heated H-mode plasma. The regression fit of the database indicates strong τE dependence on both plasma current Ip and toroidal magnetic field BT, while the dependence on density ne and absorbed power P was similar to the conventional scaling IPB98(y,2). The electron heat diffusivity is strongly affected by the plasma current and the toroidal magnetic field. The BTτE dependence on ν* is found be similar to NSTX and MAST results, while q dependence is stronger than on MAST, but weaker than in ITER scaling. The second part of the presentation is devoted to study of the particle and heat transport in regimes with qmin>1. Such transient operational modes were investigated using NBI at the current ramp-up phase, that usually causes ITB formation for particle and/or for electron heat flux (e-ITB). In the case of internal diffusion barrier it is located in the region r/a ~0.4, the e-ITB is located at r/a ~0.7. These advanced regimes are characterized with enhanced energy confinement relative to conventional H-mode.

Speaker: Dr Gleb Kurskiev (Ioffe Physical-Technical Institute of the Russian Academy of Sciences)

FEC_2018_poster_2.pdf

FEC_2018_poster_2.pptx

Kurskiev_EX_P5-sslide_2.pdf

10:15 Coffee Break

EX/6-TH/4 Runways & Disruption Mitigation

448 Advances in Runaway Electron Control and Model Validation for ITER

Measurements and modeling of runaway electron (RE) dissipation in DIII-D has resolved key experimental discrepancies and validated predictions for ITER, improving confidence that RE mitigation and avoidance can be predictively optimized without risking first-wall integrity. Energy-resolved measurements of hard X-ray (HXR) flux with a unique gamma-ray imaging (GRI) system demonstrate that anomalous dissipation of RE beams is strongest for low energy RE populations. Modeling including the self-consistent interaction of the RE population with RE-driven kinetic instabilities reproduces the enhanced dissipation and finds strong wave-particle interactions with the low energy RE population. Novel spatio-temporally resolved HXR measurements using the GRI system have also validated RE distribution function ($f_{e}$) dependencies and observed the effect of phase-space attractors that pile up REs at a given energy. Increasing synchrotron damping shifts the high-energy $f_{e}$ towards lower energy, though quantitatively observed synchrotron effects are larger than predicted. Increasing collisional damping shifts the full $f_{e}$ to lower energy. $f_{e}$ validation in both phase space and real space is further advanced by new synchrotron and bremsstrahlung emission synthetic diagnostics. These tools reproduce experimental images and can validate different pitch-angle distribution models. Considering RE seed formation and final loss, a new method to experimentally estimate the RE seed current from pellet ablation rates reveals that the hot-tail generation mechanism significantly over-estimates RE seed production, while the Dreicer mechanism is insufficient to explain the observed seed. Model predictions of first wall Joule heating during the RE final loss are consistent with experiment at high ion charge ($Z$). Discrepancies are found at low $Z$, however, indicating some RE dissipation processes remain poorly understood. The above measurements and comparison with theory substantially improves confidence that model-based optimization of RE avoidance and mitigation can be achieved. This is essential to fully exploit ITER while avoiding RE-induced damage to the first-wall. This work was supported by the US Department of Energy under DE-AC05-06OR23100, DE-FC02-04ER54698, DE-AC02-09CH11466, and DE-FG02-04ER54761.

Speaker: Dr Carlos Paz-Soldan (General Atomics)

Paz-soldan.pdf

449 Runaway electron mitigation in ITER disruptions by injection of high-Z impurities

Large amounts of MeV runaway electrons (REs) can be generated during disruptions which pose a serious threat for future large tokamak devices like ITER. Thus, it is an urgent task to develop robust and confident systems for their control and mitigation. The injection of high-Z impurities by MGI or SPI constitute one of the most promising schemes. Here, with the aim of evaluating the suitability of the injection of high-Z impurities for RE control and mitigation in ITER, the effect of injecting high-Z impurities on the RE dynamics during different phases of the disruption (before the thermal quench (TQ), during the current quench (CQ) and during the RE current plateau) is studied. First, mitigation by Ar or Ne injection before the TQ is considered with the aim of controlling the primary generation of REs during the TQ. The impurities are found to have a strong effect, leading to very low RE current generation for the shortest CQ times compatible with acceptable forces on the ITER vessel and in-vessel components in the case of Ne injection, while for the longest CQs high RE currents can be found. Mixed Ar+deuterium (D) or Ne+D injection before the TQ can be effective in controlling the generation of the RE current if a sufficient amount of Ar/Ne and D is assimilated in the plasma. If the formation of a primary RE seed cannot be avoided, impurities can be injected during the CQ with the aim of reducing the avalanche RE multiplication. The efficiency of this scheme vs. the time at which the impurities are injected and the amount of assimilated impurities (and/or D) is analyzed. Finally, if a RE plateau current is formed at the end of the CQ, impurities can be injected with the aim of yielding the dissipation of the RE current before a strong interaction with the PFCs can take place. A simplified approach to the RE beam dissipation including the effect of the collisions with the plasma particles and impurities, and the electron synchrotron and bremsstrahlung radiation, is applied. It is suggested that injection of a few kPa∙m3 of Ar could be enough for RE electron mitigation before the characteristic time for the vertical instability growth in ITER. The effect of the RE scraping-off during the decay of the current and the consequences on the amount of impurities that should be injected for an efficient RE dissipation is also analyzed.

Speaker: Dr Jose Ramon Martin-Solis (Universidad Carlos III de Madrid)

Presentation_runaway_mitigation_ITER_TH4-1_15_october_talk_2018_rev2.ppt

summary_THP4-1_martin-solis_rev _03-08-2018.pdf

450 Self-consistent runaway beam formation in 3D magnetic fields during radiation-driven disruptions

We report new simulations that predict three-dimensional (3D) spatial profiles of runaway electrons (REs) throughout the whole evolution of disruption plasmas using a nonlinear reduced MHD code including a runaway beam model. Both the RE generation mechanisms relevant to mitigated disruption scenario for D-T activation phase in ITER and the convective transport of REs due to disruptive MHD instabilities during thermal quench (TQ), such as reconnection, magnetic islands, and their overlapping, are taking into account. In our approach, REs are expressed as the advection of beam density with the zero-orbit width model, and electron runaway is taken into account as source models that account for the parametric dependence of runaway rates in the velocity space for Dreicer generation, hot-tail generation, and intrinsic high-energy electron sources (due to tritium decay and the Compton scattering of gamma rays). The range of the validity is checked via the comparison to Fokker-Planck and orbit-following simulations. The developed simulation code EXTREM is a powerful tool for studying the physical mechanisms of RE generation in the presence of disruptive MHD instabilities and those of subsequent avalanche growth. We here perform a long-term simulation of radiation-driven disruption over the avalanche timescale for the ITER 15 MA parameter with noble gas and deuterium injection. During TQ MHD instabilities, overlapping of multi-n tearing modes and subsequent m/n=1/1 mode, where the latter causes the disruption of the central electron temperature profile, are shown to play a dominant role in mixing of REs in partially-destroyed magnetic fields. The resultant seed current profile localized in the region with the safety factor around unity is inherited by the avalanche growth, and the final RE profile and the net RE generation becomes significantly different from those predicted by the conventional 1D modeling without MHD effects. The sensitivity of the results for different initial q profiles and the impurity injection condition is investigated. In particular, the effectiveness of Ar/Ne + deuterium mixture injection for RE suppression is addressed over the parameter ranges relevant to disruption mitigation scenarios in ITER.

Speaker: Dr Akinobu Matsuyama (National Institutes for Quantum and Radiological Science and Technology)

Matsu_TH_4-2_talk.pptx

TH4-2_summary.pptx

451 Pitch Angle Dynamics and Synchrotron Emission of Runaway Electrons in Quiescent and Disrupted DIII-D Plasmas

We present the validation of theoretical models for the pitch-angle probability distribution function (PDF) of runaway electrons (RE), through simulations of synchrotron radiation (SR) in DIII-D quiescent [1] and disrupted [2] plasmas for which the energy PDF is known from measurements but the pitch-angle PDF is poorly understood. SR of RE in magnetically confinement fusion plasmas is important because it provides a limiting mechanism of the maximum energy that RE can reach, and because it can be used as a diagnostic to infer parameters of the RE energy and pitch-angle PDFs. Recent studies using the SR synthetic diagnostic [3,4] showed that SR depends on the RE energy, and more strongly on their pitch-angle PDF. Our simulations of RE in quiescent plasmas recover the typical visible SR in DIII-D when the spreading in the initial RE pitch-angle is less than the predicted by simplified theory that only consider the balance of electric field pinching in pitch angle and collisional pitch-angle scattering. We also present results of simulated infrared SR of RE in DIII-D disrupted plasmas after following their dynamics for tens of ms to find a better estimate for their pitch-angle PDF that takes into account the full-orbit dynamics of RE [5], SR energy losses, the acceleration of the electric field, the magnetic field geometry, and collisions with the background plasma and impurities through the use of experimental impurity density profiles. [1] C. Paz-Soldan et al., PRL 118, 255002 (2017); [2] E. M. Hollmann et al., PoP 22, 56108 (2015); [3] L. Carbajal et al., PPCF 59, 124001 (2017); [4] D. del-Castillo-Negrete et al., PoP accepted (2018); [5] L. Carbajal et al., PoP 24, 042512 (2017) *Research sponsored by the Office of Fusion Energy Sciences of the U.S. DOE at Oak Ridge National Laboratory, managed by UT-Battelle, LLC, for the U.S. DOE under contract DE-AC05-00OR22725, and by the Laboratory Directed Research and Development Program of Oak Ridge National Laboratory. Research sponsored by the Office of Fusion Energy Sciences of the U.S. DOE under contracts DE-FC02-04ER54698, DE-FG02-07ER54917. This research used resources of the National Energy Research Scientific Computing Center, a DOE Office of Science User Facility supported by the Office of Science of the U.S. Department of Energy under Contract No. DE-AC02-05CH11231.

Speaker: Dr Leopoldo Carbajal (Oak Ridge National Laboratory)

IAEA_Oral_FINAL.pptx

452 Asymmetric wall force reduction in ITER and JET disruptions

It has been thought that asymmetric vertical displacement event (AVDE) disruptions in
ITER might produce large electromechanical forces on the walls and other conducting structures
surrounding the plasma.
It is shown that ITER
AVDE disruptions
should produce a small
asymmetric wall force, comparable to JET. This is demonstrated in simulations [1,2] with the M3D 3D MHD code [3] and confirmed in JET
experiments [4]
in which the current was quenched with massive gas injection (MGI).
In ITER the current quench (CQ) time, tau_{CQ}, is less than or equal to the resistive wall
penetration time, tau_{wall}.
JET is in a different parameter regime, with tau_{CQ} > tau_{wall}.
JET simulations were validated by comparison [1] to JET shot 71985 data and were in good
agreement. The wall time was then artificially increased, keeping tau_{CQ} fixed,
and it was found
that the wall force decreased.
The reduction of the asymmetric wall force was also found in experimental data [4] of
JET MGI mitigated disruption shots.
Further simulations [2] were carried out of ITER AVDEs. The asymmetric wall force was calculated for a wide range of CQ times.
For tau_{CQ} < tau_{wall}, the force was
not much larger than in JET.
A fast CQ may cause production of runaway electrons (REs).
The effect of replacing part of
of the current with REs on MHD behavior will be discussed.
Simulations using a modified
version of M3D with a fluid RE model [5] will be presented.

Acknowledgment: Work supported by USDOE and
Euratom research and training programme
2014-2018 under grant agreement No 633053,
within the EUROfusion Consortium.
Views and opinions herein do not necessarily reflect
those of the European Commission.

[1] H. Strauss, E. Joffrin, V. Riccardo, J. Breslau, R. Paccagnella, Phys. Plasmas 24, 102512 (2017).

[2] H. Strauss, Physics of Plasmas 25, 020702 (2018).

[3] W. Park, E. Belova, G. Y. Fu, et al., Phys. Plasmas 6, 1796 (1999).

[4] S. Jachmich, P. Drewelow, et al., 43rd EPS Conf. Plasma Physics (2016)

[5] Huishan Cai and Guoyong Fu, Nucl. Fusion 55, 022001 (2015).

Speaker: Dr Henry Strauss (HRS Fusion)

Strauss_H_jet3iter5.pdf

12:30 Lunch

EX/5, PPC/1-TH/3-EX/6-TH/4 P6 Posters

453 Advances in Runaway Electron Control and Model Validation for ITER

Speaker: Dr Carlos Paz-Soldan (General Atomics)

Paz-soldan.pdf

Paz-Soldan_RE_summary.pptx

454 Asymmetric wall force reduction in ITER and JET disruptions

Speaker: Dr Henry Strauss (HRS Fusion)

Strauss_H_jet3iterslide2.pdf

455 First principles and integrated modelling achievements towards trustful Fusion power predictions for JET and ITER

Speaker: Dr Jeronimo Garcia (CEA IRFM)

IAEA2018_slide.pptx

456 Pitch Angle Dynamics and Synchrotron Emission of Runaway Electrons in Quiescent and Disrupted DIII-D Plasmas

Speaker: Dr Leopoldo Carbajal (Oak Ridge National Laboratory)

457 Predicting the Toroidal Rotation Profile for ITER

Speaker: Dr Colin Chrystal (General Atomics)

458 Predictive integrated modelling of plasmas and their operation scenarios towards exploitation of JT-60SA experiment

Speaker: Dr Nobuhiko Hayashi (National Institutes for Quantum and Radiological Science and Technology)

IAEA18_Hayashi_v11_limit_c_wo_anime.pptx

Summary_slide_PPC:1-1.pptx

459 Predictive multi-channel flux-driven modelling to optimise ICRH tungsten control in JET

Speaker: Dr Francis Casson (UKAEA)

Casson_IAEA_2018_slides3.pdf

Casson_IAEA_2018_slides3_wide5.pdf

Casson_IAEA_poster2a.pdf

Casson_summary_slide.pdf

460 Runaway electron mitigation in ITER disruptions by injection of high-Z impurities

Speaker: Dr Jose Ramon Martin-Solis (Universidad Carlos III de Madrid)

summary_THP4-1_martin-solis_rev _03-08-2018.pdf

461 Self-consistent runaway beam formation in 3D magnetic fields during radiation-driven disruptions

Speaker: Dr Akinobu Matsuyama (National Institutes for Quantum and Radiological Science and Technology)

462 Transport characteristics of deuterium and hydrogen plasmas with ion internal transport barrier in LHD

Speaker: Prof. Kenichi Nagaoka (National Institute for Fusion Science)

Nagaoka_EX5-1_16_9_v102.pptx

Nagaoka_EX5-1_16_9_v52.pptx

Summary_EX5-1_Nagaoka.pptx

OralPresentation Backup_Nagaoka_EX5-1_16_9_v3.pptx Nagaoka_EX5-1_16_9_v3.pdf

FIP/2, MPT/1, SEE/1 In Vessel Components & Plasma Interface

463 Tritiated Dust: their impact on tokamak operation

During the ITER operation, plasma interacts with the machine plasma facing components (PFCs) through various physical processes and gives birth to particles from nanometer to tens of micron sizes that are called dusts in the fusion community. Depending on the plasma wall interaction, different types of dust will be created from almost spherical particles induced by high heat flux interaction with metal (unipolar arcs, ELMs, disruption) to fractal ones created by accretion in the edge of this high density/long pulse plasma machine. The dust properties especially their ability to be covered by an oxide insulating layer and their surface topology deeply affect their tritium inventory. As instance, it has been already shown [El Kharbachi- 2014] that dust tritium inventory is two to three orders of magnitude higher than massive material. It can be then asserted that tritium inventory can be ranged from some GBq/g for tungsten particles to much higher values for beryllium ones. Due to tritium beta decay, these particles are rapidly positively charged. As an example, a 5 μm diameter single tungsten particle with a tritium inventory of 10 GBq/g will have a charge of 6.10 17 Coulomb in 1 hour. Dust physico-chemical properties and radioactive electrical self-charging process have numerous consequences in term of operation and safety and the major goal of this \ presentation is to highlight them. The first step of this paper consists to list how the dusts are created in the ITER machine using laboratory and tokamak current results. The properties of the created particles (composition, size and morphology) considering all the physical processes initiated in this framework will be presented. Moreover, we will insist here on the fact that all the particles are covered by an insulating oxide layer that triggers dust adhesion properties as it has been clearly exemplified in [Peillon-2017]. In this paper, experimental investigations on the electric field strength required to overcome the adhesion forces of micron size tungsten metallic dust as well as silver and aluminum oxide in powdery form deposited on a conductive surface are presented.

Speaker: Mr Christian Grisolia (CEA)

Grisolia Gendarmes AIEA final 16_9 .pptx

summary Grisolia Gendarmes AIEA.pdf

464 Progress in Developing ITER and DEMO First Wall Technologies at SWIP

The ITER enhanced heat flux (EHF) FW panel utilizes a Be/CuCrZr/316L(N) joint structure with hypervapotron (HVT) cooling channel in the CuCrZr heat sink to withstand cyclic surface heat flux up to 4.7 MW/m2. For Chinese CFETR and DEMO, the heat load will be much lower and a simple W/RAFM steel joint with cooling channels in the steel will be used. For all of them, reliable material bonding joint is one of the essential requirements. It is found that the thermal fatigue life of the ITER EHF FW structure could be increased by more than one order if a bottom groove is added to the HVT channel. A hot iso-static pressing (HIP) joining technology has been successfully developed for bonding Be tiles onto the CuCrZr alloy heat sink with a Ti/Cu interlayer. Full-size EHF FW fingers were manufactured with a success rate of ~90%. Analyses show 6 inter-layers with Cu-Ti intermetallic phases formed at the interface during the HIP process. Thinning the Cu4Ti layer could lead to a defect-free Be/Cu interface. An ITER EHF FW semi-prototype with 6 Be/CuCrZr/316L(N) fingers was successfully manufactured in 2015. Two finger pairs were subjected to thermal fatigue test at 4.7 MW/m2 for 7500 cycles and 5.9 MW/m2 for 1500 cycles under active water cooling in 2016. The finger pairs remain perfect without any damage. A post-test dimensional examination showed merely 20μm deformation in maximum. The vacuum tightness of their HVT cooling channels were kept as good as before the test. Several manufacture routes are under investigation for W/RAFM steel joints. The key is to use a low activation interlayer to accommodate the thermal stress between them. A defect-free joint was made by brazing at 1270℃ with Fe-Cr-B-Si amorphous filler material and pure V as accommodation layer. The property of the CLF-1 RAFM steel was fully recovered by a PWHT. In developing the fast CVD W coating on CLF-1 steel, a CVD TiN coating was firstly applied on the steel acting as a tritium permeation barrier. Good bonding performance is presented and neither obvious defect nor detachment is found at the working temperature of 550℃. For the HIP joining, a couple of joints have been made by HIP at 740℃ using pure Cr, V and Fe interlayer. Further tests will be done at higher HIP temperature with fast cooling of >20℃/min to enable the recovery of the microstructure and properties of the CLF-1 steel.

Speaker: Prof. Jiming Chen (Southwestern Institute of Physics)

2018_IAEA_27thFEC_ChenJiming_v1.6.pdf

PPT_2018_IAEA_27thFEC_ChenJiming_v1.6.ppt

Summary slide for FIP2-1 of IAEA-CN-258 manuscript.pdf

465 Technologies for Plasma-Facing Wall Protection in EU DEMO

The plasma-facing wall of the main chamber in DEMO will be unlike any current tokamak. The blanket first wall (FW) is to be actively-cooled reduced-activation steel (Eurofer) under a thin plasma-facing tungsten armour. To help control cost, modest misalignment of this wall must be tolerable at least with respect to a relatively quiescent divertor plasma flat-top equilibrium. However, with present knowledge it is not possible to exclude normal or off-normal plasma transient phases, and during some of these transients the blanket FW will not be sufficient in terms of the engineering heat flux limit of the plasma-facing technology. Particularly challenging are transients during which the plasma is limited, for example during plasma start-up or vertical displacement events (VDEs). In EU-DEMO we propose discrete limiters, with large gaps between them, which serve to protect the blanket FW from these plasma transients. In this work, two proposed protection components are presented: an equatorial port limiter which receives power during the start-up phase, and an upper wall “dump” panel which is intended to sacrificially protect the blanket system in the event of an upward-VDE. The plasma-facing component (PFC) engineering designs, although an evolution of the ITER W/CuCrZr divertor monoblock technology, are tailored according to their respective transient loading requirements. For the start-up limiter designed for 30-60 second ramp-up phase, we show by thermal-structural finite element analyses that the heat sink properties of tungsten can be exploited to improve the component heat flux limit. This equatorial limiter features a water-cooled Eurofer plug behind the PFCs for neutron shielding and connection to the stainless steel port plug. The manufacturing and assembly proposal for the limiter is described and the effect of the limiter on reactor tritium breeding ratio is shown. In the case of the upper dump PFC, the huge amount of energy deposited during the VDE could lead to extensive melt damage of the tungsten armour. However, the PFC described here has features to deliberately channel the heat flux to the sides and rear of the coolant pipe, and we show by transient engineering analyses that this technique can markedly increase the heat load at which structural failure of the coolant pipe occurs, reducing the likelihood of a loss of coolant accident.

Speaker: Dr Thomas R. Barrett (UkCCFE)

Oral IAEA FEC_DEMO PF technologies_Barrett_v3.pptx

Summary Slide SummSlide_IAEA FEC_DEMO PF technologies_Barrett.pdf

466 Active conditioning of ASDEX-Upgrade tunsgten PFCs through boron particulate injection

The injection of boron (B) and boron nitride (BN) powders into ASDEX-Upgrade (AUG) H-mode discharges have shown the ability to effectively control tungsten influx in low density/collisionality operational regimes, similar to conventional boronization methods. A newly designed impurity powder dropper was installed onto AUG with 5m diameter BN powder, and 50 m B powder (99%+ purity) loaded into separate dropper assemblies. The sub-mm powder particles are gravitationally accelerated into the upper edge of a lower single null H-mode plasma. Discharges with IP = 800 kA, ne = 6x1019 m-3, PNBI = 10 MW , and a conformal boundary shape were used for the conditioning sequences. These were followed by different discharges to evaluate the effects of the conditioning.
The first experiment was performed with five BN conditioning discharges, in which injected B was varied from ~4x1018 atoms/discharge to ~4x1020 atoms/discharge. Visible spectroscopy measurements at the outer limiter showed increases in both boron and nitrogen signal levels, well as elevated boron levels in the divertor and an increase in PRAD by greater than a factor of 2. Globally the BN injection also improved energy confinement by 10-20%, similar to gaseous N2 injection. Discharges with increasing B injection rates were also performed. Injecting, 9.2x1021 atoms of pure B resulted in minimal impact on plasma performance and up to 50% increase in radiated power. To test the conditioning effect of B powder, a sequence of discharges with magnetic perturbations for ELM suppression were conducted afterwards. Historically these discharges are very sensitive to wall conditions. However, following the B conditioning discharges, all three attempts to run low density discharges with ELMs suppressed by magnetic perturbations were successful. These preliminary results suggest that the application of B containing powders can be used to both improve plasma performance in real-time, and improve wall conditions. Furthermore the injection system is capable of injecting a wide number of impurities (B, BN, B4C, Li, C, Sn, Mo, W, …) for a range of studies. Similar systems are being installed on the EAST and DIII-D devices. Results from these and forthcoming studies on AUG, and possibly other devices, will be reported. The U.S. authors supported by U.S. Dept. of Energy contract DE-AC02-09CH11466.

Speaker: Dr Robert Lunsford (Princeton Plasma Physics Laboratory)

IAEA2018_FEC2-3_Lunsford.pdf

Lunsford_IAEAFEC2018_FIP_2-3_final.pdf

467 Advances in predictive thermo-mechanical modelling for the JET divertor experimental interpretation, improved protection, and reliable operation

The JET targets are the in-vessel components which receive the largest sustained thermal load. Operating instructions limit the energy and maximum surface temperature allowed for each shot, while IR cameras are used for protection during each discharge. Surface delamination and radial cracks have been observed in the outboard tungsten-coated CFC tiles, while bulk tungsten special lamellas were intentionally melted in dedicated experiments. These different types of damage were not reproducible using existing models and tools. Several analysis and development activities have been performed during the last campaigns for their improvement, covering from the prediction of the plasma parallel heat flux density to the transient thermo-mechanical behaviour of the tiles. The parallel heat flux density is reconstructed from the surface temperature measurements—acquired by the experimental IR cameras—using inverse analysis techniques. New inverse algorithms have been developed for a realistic representation of the tile geometry and coating thickness. A set of geometrical and loading projection corrections have been introduced which explain a reduction of the measured parallel heat flux density of up to 1/3 when compared to previous estimations. Once the corrected parallel heat flux has been characterized, predictive analysis can be run for ensuring that the maximum temperature and stress remain within the allowable limits. The integrity assessment of the tiles uses a profile of the heat load defined by an engineering footprint, which has been correlated to several plasma parameters. The engineering footprint averages the inter-ELM, ELM transients, and associated strike point movements, leading to a wider footprint compared to that obtained using typical inter-ELM scaling laws. This has turned out to be critical for replicating the deformation effects of the tiles. The observed failure modes can now be reproduced—and therefore avoided—by means of coupled-field 3D thermo-mechanical models. All these improvements have been implemented in integrated analysis tools which can predict the behaviour of the divertor tiles in a power consistent manner. This development carried out at JET supports the experimental understanding, enhances the real-time protection systems, improves the evaluation of the operating instructions, and is also transferable to ITER.

Speaker: Dr Daniel Iglesias (UK Atomic Energy Authority)

Iglesias-FEC-FIP2_v2.pdf

Iglesias-IAEA-FEC_v4 - talk.pptx

468 Influence of Plasma Impurities on the Fuel Retention in Tungsten

The first wall in ITER will be subjected to mixed species fluxes containing hydrogenic isotopes, helium produced in D-T reactions and radiator gases such as argon, neon or nitrogen. It is necessary to test how plasma-facing materials perform with respect to hydrogen retention under the mixed species plasma conditions. In this study, the influence of helium, argon, neon and nitrogen as plasma impurities on the deuterium retention in tungsten was investigated in the linear plasma devices PSI-2 and PISCES-A. Tungsten samples were mechanically polished then recrystallized at 2070 K for 1 h before the exposure. Following mixed plasmas were produced: pure D, D+0.03He, D+0.07Ar, D+0.1Ne, D+0.05N and D+0.03He+0.07Ar. The exposure conditions were as follows: incident ion flux of ~10^21 to 10^22 m^-2s^-1, incident ion fluence of 1x10^25 to 1x10^26 m^-2, sample temperatures of 500 and 770 K. The incident ion energy was 70 eV, above the W sputtering threshold for Ar and N, but below it for D and He. For Ne, in addition, it was varied between 20 and 70 eV, below and above the W sputtering threshold, respectively. After exposures, samples were analysed by SEM, TEM, NRA and TDS. The admixture of He reduced the D retention by one order of magnitude, while Ar increased it by about 50%. In the D+He+Ar case the effect was similar as for D+Ar. Ar probably sputtered the near-surface layer and thus overrode the effect of He. The effect of Ne appeared to be sensitive on the incident ion energy. Ne had an effect similar to Ar increasing the D retention for the ion energies above the sputtering threshold, while for lower energies its effect was less pronounced. Addition of nitrogen increased the D retention by a factor of ~10 and ~100 for 500 K and 770 K, respectively. In general, the effect of impurities on the D retention appears to be sensitive to the properties of the damaged near-surface layer of tungsten. Admixed species, i.e. He, can form a near-surface damaged layer with open porosity, which serves as an escaping channel for D thus decreasing the D retention. However, if the process is dominated by sputtering, as for Ar, such a layer cannot be formed. The N enriched layer, in contrast, serves as a desorption barrier for D increasing its retention.

Speaker: Dr Arkadi Kreter (Forschungszentrum Juelich)

kreter_fec2018_MPT1-1.pptx

MPT1-1_kreter_summary_slide.pptx

P6 Posters

469 Access Requirements for Stationary ELM-suppressed Pedestals in DIII-D and C-Mod Plasmas

Analysis of pedestal characteristics for Quiescent H-mode (QH) and I-mode plasmas from recent experiments on DIII-D and C-Mod exhibit a growing understanding of the access requirements necessary to obtain edge fluctuations or MHD that drive edge particle transport needed to remain ELM-free. In DIII-D QH-mode plasmas, critical values of ExB shear are required in experiment in order to suppress the transition from QH-mode to ELMy H-mode. The experimental shear values for QH-modes ranging between $q_{95}$~3-5 and $\delta$~0.36-0.68 are compared with theory [1] to show good agreement with the predicted scaling parameters of $c_s/\sqrt{L_p \Delta x}$, where $c_s$ is the ion acoustic velocity, $L_p$ the pressure gradient scale length, and $\Delta x$ is the radial width of the mode. The scaling of the critical shearing rate agrees with experiment, but the absolute magnitude of the limit is over-predicted by theory by two orders of magnitude. Through a normalized predictive scaling, the model demonstrates dynamic transitions into and out of QH-mode qualitatively within a single plasma discharge. C-Mod I-mode plasmas, which lack an edge particle barrier and exhibit characteristic edge fluctuations over a broad range of $B_\phi$ [2], meet upper limits in performance determined by H-mode access. The maximum radial electric field well in I-mode increases with magnetic field strength, suggesting the expanded window for I-mode at high field is linked to a critical value of $E_r$/B required to induce an H-mode transition. C-Mod I-mode pedestals are analyzed over varied magnetic fields (2.8-5.8T) and auxiliary power (1.5-4.6 MW) to show consistent edge fluctuation behavior. Density fluctuations associated with the Weakly Coherent Mode are observed to span the pedestal region, extending out to the separatrix, while the fluctuation associated with the Geodesic Acoustic Mode is observed on the profile reflectometer near the foot of the T_e pedestal. Trends in the edge $E_r$, ExB shear, and rotation in I-mode show little correlation with the behavior of the edge fluctuations, suggesting an alternate driver for destabilization of the WCM and GAM, as compared to the QH-modes analyzed for DIII-D with an EHO.

Speaker: Dr Theresa Wilks (UsMIT)

Wilks_IAEA_Proceedings.pdf

Wilks_summary.pptx

470 Advancing Local Helicity Injection for Non-Solenoidal Tokamak Startup

Robust non-solenoidal startup methods may simplify the cost and complexity of next-step burning plasma devices, and especially STs, by removing the need for a solenoid. Experiments on the $A\sim1$ Pegasus ST are advancing the physics and technology basis of Local Helicity Injection (LHI). LHI creates high-$I_p$ tokamak plasmas without a solenoid by injecting helicity with small current sources in the plasma edge. Its hardware can be withdrawn before a fusion plasma enters a nuclear burn phase. Flexible injector placement offers tradeoffs between physics and engineering goals. They are tested with LHI systems on the low-field-side (LFS) and the high-field-side (HFS) of Pegasus, producing plasmas predominantly driven by non-solenoidal induction and DC helicity drive ($V_{LHI}\sim B_{inj}A_{inj}V_{inj}$), respectively. Record LHI plasmas with $I_p = 0.2$ MA, $T_e > 100$ eV, $n_e\sim10^{19}$ m^-3, and $Z_{eff} < 2.5$ are attained. A predictive 0D power-balance model describes experimental $I_p(t)$ and partitions the active current drive sources. It uses improved inductance models that have been extended to $A\sim1$. The analysis confirms the dominance of induction in LFS LHI and DC helicity drive in HFS LHI. Model projections for NSTX-U suggest MA-class LHI startup may be feasible with a modest LFS system. An advanced port-mounted LHI system is being deployed on Pegasus to test this path. Studies of HFS scenarios find favourable, positive scalings of $I_p$ with $V_{LHI}$ and $T_e$ with $B_T$. If they hold at higher $B_T$, LHI may directly offer useful targets for RF and NBI current drive. High-frequency MHD activity plays a strong role in LHI current drive, in addition to $n=1$ modes previously found in NIMROD simulation and experiment. A new regime of reduced MHD activity was discovered where the $n=1$ activity is suppressed. In this regime, high-frequency activity increases, LHI CD efficiency improves, and long-pulse plasmas are sustained with $V_{IND}\sim0$. LHI facilitates access to the favourable low-$A$ ST regime with non-solenoidal sustainment, high $\kappa$, low $\ell_i$, and high $\beta_t$. Low $B_T$ LHI operation has led to record $\beta_t=100$%, high $\beta_N$, and a minimum-$|B|$ well that may positively affect turbulence, transport, and fast particle confinement. Discharges at highest $\beta_t$ disrupt at the ideal no-wall MHD limit.

Speaker: Dr Michael Bongard (University of Wisconsin-Madison)

Bongard_EX_P6-34.pdf

Bongard_EX_P6-34_Summary_Slide.pdf

471 Analysis and modelling of NTMs dynamics in JET discharges using the European Transport Simulator (ETS) and integrated modelling tools

Stability of JET baseline and hybrid scenarios from previous and present experimental campaign is investigated in the framework of the JET1 task on MHD analysis and modeling in support of scenario development. Modeling of Neoclassical Tearing Modes (NTMs) onset and their effect on heavy impurity transport is performed via the European Transport Simulator (ETS), encompassing an NTM module and MHD stability calculation. The present study is aimed to predict plasma stability conditions avoiding the appearance of NTMs which limit the plasma performance and duration in DT scenarios. In addition, the high energy confinement in hybrid discharges can be deteriorated if impurities accumulate towards the plasma centre. The NTM module implemented in the ETS describes the NTM dynamics by a set of equations for the mode width, through a generalized Rutherford equation and frequency. Investigation and validation of the mode trigger models can be performed with this module as well as the analysis of the effects of NTM on electron, ion and impurity transport. Enhanced perpendicular diffusion coefficients around the mode location is modeled by adding a Gaussian perturbation. In JET discharges, this modification has been considered for electron transport coefficient and similarly used to model the enhancement of tungsten diffusion coefficient initially observed around the mode location. ETS simulator is appropriate since it can compute the evolution of impurities in all their ionization states. A first validation of MHD stability models was performed comparing the mode stability parameter using 4 different codes: NTM module in ETS, Delta Prime Calculation Code, 3D quasi-analytic code and TRANSP. Full MHD code MARS is also used for comparison of linear growth rate evaluation of the mode with the stability parameter index calculated by the other codes. MARS is part of the Equilibrium & MHD Stability Workflow and the analysis will make use of the outputs produced by the ETS at some time snapshots. All the results obtained from the MHD analysis via these (transport) codes provide a new modelling investigation of the plasma stability for JET baseline and hybrid discharges. A detailed discussion of the calculations will be reported.

Speaker: Dr Silvana Nowak (IFP - CNR , Milano, Italy)

65060_iaea_summary_slide_nowak_rev2.pdf

472 Application of the Semi–Implicit Numerical Method on the Radial Impurity Transport Equation and Determination of O4+ Emissivity with Two Separate PEC Databases

The radial impurity transport equation describes the distribution of impurity ion species with different charge states perpendicular to magnetic surfaces of tokamak plasma. The impurity transport equation for each ion with ionization state Z is a second order, coupled, parabolic partial differential equation described in terms of number densities of charge states Z, Z-1 and Z+1. A semi–implicit numerical method has been applied over radial impurity transport equation to obtain the number densities of oxygen ions in present case. The numerical method applied suggests segregating the terms of the transport equation into implicit and explicit forms thereby adhering to a single time treatment (either implicit or explicit) for each of its constituent term. A forward in time and central in space (FTCS) scheme of discretization have been applied first. The terms associated with diffusivity and ionization and recombination terms of charge state Z are next rendered implicit; terms associated with convective velocity, ionization of charge state Z-1 and recombination of charge state Z+1 remain explicit. The system studied is the Aditya tokamak (ro=0.25 m, R=0.75 m, Bt =0.75 T) installed at the Institute for Plasma Research, Gandhinagar, India. Plasma in Aditya is circular in cross–section being confined within limiter. The number density of O4+ ions determined using semi–implicit numerical method is used further to obtain radial emissivity profile of (650.024 nm) transition of O4+ ion and compare it with experiment data. The emissivity values of 650.024 nm characteristic line of Be–like O4+ ion, in visible–spectral region, have been obtained by measuring the brightness in high magnetic field (inboard) and low magnetic field (outboard) regions of Aditya tokamak and applying an Abel–like matrix inversion on it. Present study compares the emissivity calculated with number density of O4+ ion obtained using semi–implicit method with O4+ emissivity obtained experimentally using two databases of Photon Emissivity coefficients (PECs) namely the ADAS (Atomic Data and Analysis Structure) and NIFS (National Institute of Fusion Science) database. The PECs in two databases differ due to a difference in the atomic processes considered while calculating them. This difference thereby influences the radial emissivity profiles of O4+ ion studied in present case.

Speaker: Ms AMRITA BHATTACHARYA (INDIAN INSTITUTE OF TECHNOLOGY KANPUR)

FEC2018_ABhattacharya_Summary_Slide.pptx

473 Confinement in stellarators with the global gyrokinetic code XGC

Whole-volume gyrokinetic simulations of stellarators are necessary to address a number of important physics and engineering issues, including energetic particle confinement op- timisation and turbulent transport prediction. In recent work, a whole-volume stellarator version of the global gyrokinetic Particle-In-Cell (PIC) code XGC[1] is under development. A 3D interpolation of equilibrium magnetic field to the last closed flux surface, calculated using the VMEC MHD equilibrum code, has been implemented, along with a 3D mesh for calculating the evolution of the electrostatic potential. The 3D version of XGC has been successfully benchmarked with the NBI code BEAMS3D[2] and the core 3D gyrokinetic code EUTERPE[3] for energetic particle orbit tracing in Wen- delstein 7-X (W7-X) geometry. It has been used to investigate collisionless alpha particle confinement in potential stellarator reactor designs. The new tool permits direct comparison for alpha particle loss between quasi-axisymmetric and quasi-isodynamic designs. Furthermore, microturbulence has been observed in the outer portion of the core, and in the edge, of the W7-AS stellarator[4], and is likely to dominate in this region of Wendelstein 7- X or any stellarator reactor. Developments to the XGC code will permit 3D global simulation of ion-scale turbulence in stellarators, which has so far not been achieved. By simulating first the linear stage of the Ion Temperature Gradient-driven (ITG) instability, and then nonlinear turbulence, XGC will be applied to better understand the global behaviour of turbulence in the Wendelstein 7-X stellarator. 1. S.-H. Ku, C.-S. Chang, and P. Diamond, Nucl. Fusion 49, 115021 (2009). 2. M. McMillan and S. A. Lazerson, Plasma Phys. Control. Fusion 56, 095019 (2014). 3. V. Kornilov and R. Kleiber, Phys. Plasma 11, 3196 (2004). 4. M. Hirsch et al., Plasma Phys. Control. Fusion 50, 053001 (2008).

Speaker: Dr Michael Cole (Princeton Plasma Physics Laboratory)

cole_iaea_fec18_summaryslide.pdf

474 Critical Processes of Tearing Mode Entrainment in the Presence of a Static Error Field

M. Okabayashi
Princeton Plasma Physics Laboratory, PO Box 451, Princeton, NJ 08543-0451, USA
mokabaya@pppl.gov
DIII-D experiments on control of locked tearing modes are in good qualitative
agreement with predictions of a non-linear reduced MHD code (AEOLUS-IT) [1].
Robust avoidance of locked tearing modes that may cause disruptions is a prerequisite
for successful ITER operation. We have tested model predictions that entrainment of
a locked mode by a rotating 3D field screens out the error field that caused the initial
locking. The plasma condition was the ITER base line scenario target with low safety
factor discharges. The simulation is nonlinear, but highlights the fundamental process
by simplifying the physics to a zero beta, single helicity case with m/n=2/1, using
only the vorticity equation and Ohm’s law without any additional transport properties.
Experiment and simulation both show coupling between the locked mode and a stable
kink around the rational surface, and the screening that follows a bifurcation event in
which the mode becomes locked to the rotating applied field. Experiments in DIII-D
have illuminated some of the critical physical processes in the interaction of a locked
tearing mode with a rotating 3D field, including torque balance bifurcation and
entrainment in the presence of a static error field. Time evolution of local mode
structure near q=2 rational surface including the perturbed rotation profile using
Charge Exchange Recombination (CER) has been very useful for the comparisons.
Predictive understanding of mode evolution is crucial to the design of locked mode
control schemes that will help to avoid disruptions in present and future devices, and
the non-linear reduced MHD model AEOLUS-IT is in good qualitative agreement
with experimental observations. Such models will enable design of experiments on
locked mode control and other nonlinear MHD processes in present devices, and
extrapolation of these studies to large-scale experiments such as in ITER.
This work was supported in part by the US Department of Energy under DE-AC02-
09CH11466, DE-FC02-04ER54698, DE-FG02-04ER54761
(1) S. Inoue et al., NF 2017 57, 116020-10, S. Inoue et al., PPCF 2018 online

Speaker: Dr Michio Okabayashi (Princeton Plasma Physics Laboratory)

Okabayashi.M-EX-P6-25_SummSlide.pptx

475 Development and First Experimental Tests of a Small Angle Slot Divertor on DIII-D

A Small Angle Slot (SAS) divertor has been installed on the DIII-D tokamak to further evaluate the role of divertor closure in achieving efficient heat dispersal for steady-state tokamaks. Initial experiments have shown a significant reduction of the electron temperature (T_e) across the divertor target and access to dissipative divertor operation at lower H-mode operational densities while maintaining high core plasma confinement. The SAS configuration features a small (glancing) angle target and a narrow slot progressively flaring out from the strike point to amplify both neutral and impurity dissipation of power in the divertor. Experiments with closely matched H-mode discharges in DIII-D have demonstrated that SAS achieves dissipative divertor conditions with T_e < 10 eV at a lower main plasma density than in an open (horizontal) divertor configuration, based on target Langmuir probe measurements. In addition, SAS can extend plasma cooling into the far Scrape-Off Layer (SOL), in contrast to the vertical target configuration which usually achieves partial detachment with low T_e in the near SOL only. SAS also achieves improved confinement with a confinement enhancement factor H_98Y2 ~ 25% higher than the open divertor at the onset of detachment. SAS also widens the high performance H-mode operating window through detachment onset at lower density and X-point MARFE formation at higher density. Detailed transport and pedestal stability analyses find that the confinement improvement with SAS are associated with higher pedestal temperature and pressure, which are primarily due to an increased pedestal width, consistent with previous divertor closure experiments on DIII-D. These results were obtained with the ion grad-B drift away from the SAS divertor. Further research will be conducted to establish the role of drifts in a closed slot divertor and results will also be presented. Work supported by the US DOE under DE-FC02-04ER54698, DE-AC04-94AL85000 and DE-AC05-00OR22725, and GA corporate funding.

Speaker: Mr Houyang Guo (General Atomics)

Guo-Sumary Slide EX_P6-10.pptx

476 Development of a High-Flux Fusion Neutron Source Using Recent Advances in Technology

Abstract: We report an overview of theoretical and experimental work at the University of Wisconsin leading to a fusion neutron source based on the Gas Dynamic Trap concept. The design considers the implications of several recent physics and technological advances and uses (1) off-the-shelf MRI magnets for an inexpensive central cell, (2) state-of-the-art small and planar high field REBCO magnet for plugs, (3) state-of-the-art gyrotrons to allow high density operation, (4) sloshing ions to localize neutron yield away from sensitive high field magnets at edge, (5) radio-frequency heating at the fast-ion turning points to enhance neutron yield, (6) a liquid lithium expanding diverter for heat removal, electron thermal barrier and MHD stability---lithium seems essential for pumping neutrals, minimize sputtering by ion bombardment, and minimize secondary electron emission to allow the electron thermal barrier to form. Equilibrium, stability, plasma heating have been modeled using a Grad-Shafranov solver for the mirror including fast ion pressure coupled to the CQL3D/Genray suite of codes. Initial results were extremely promising. 5 MW of neutral beam injection power and 5 MW of rf heating at 15 MHz generated 1015 neutrons/sec in DD. In addition, progress on the construction of a prototype GDT using REBCO mirror coils a lithium divertor solution will be reported.

Speaker: Prof. Cary Forest (University of Wisconsin-Madison)

477 DIII-D Shaping Demonstrates Correlation of Intrinsic Momentum with Energy

Scaling of intrinsic rotation in DIII-D H-mode plasmas demonstrates a strong correlation with the ion temperature (Ti) and stored plasma thermal energy, indicating a coupling between the turbulent intrinsic momentum flux and the turbulent energy flux [1]. The empirical scaling [1] of intrinsic rotation with plasma stored energy has been recently explored by novel experiments on DIII-D that utilize relatively small variations in the plasma shape, namely the triangularity, to modify the intrinsic rotation. Shape variation modifies the turbulent transport, rather than via changes in the auxiliary heating power. These H-modes are heated by ECH with no external torque input. Balanced torque blips from neutral beams [1] measure the ion flow velocity and Ti. Higher energy and intrinsic angular momentum are correlated with higher triangularity. The measured results follow the recently established DIII-D empirical scaling [1]. Turbulent density fluctuations in the pedestal region show a significantly higher level in the lower triangularity, lower confinement phases, possibly the source of greater transport. Changing triangularity is more subtle than the up/down symmetry change experiments in TCV [2], In DIII-D, we postulate that ExB shear likely provides the dominant symmetry breaking necessary for a net turbulent momentum stress, rather than the shaping, per se. *This material is based upon work supported by the Department of Energy under Award Numbers DE-FC02-04ER54698, DE-FG02-08ER54984, DE-FG02-07ER54917, and DE-AC02-09CH11466. [1] J.S. deGrassie et al, Phys. Plasmas 23, 082501 (2016). [2] Y. Camenen et al, Phys. Plasmas 16, 062501 (2009).

Speaker: Dr John deGrassie (General Atomics)

deGrassie_EX:P6-1_SummarySlide.pdf

478 Disruption Event Characterization and Forecasting in Tokamaks

Disruption prediction and avoidance is a critical need for next-step tokamaks such as ITER, as disruptions can place significant thermal heat loads and electromagnetic forces on the device and can potentially lead to damage from runaway electrons. Meeting these challenging goals with the high reliability required for ITER and future tokamaks requires multiple approaches, including an understanding of the connection between events leading to disruptions, and the ability to forecast such events. The Disruption Event Characterization and Forecasting Code (DECAF) is used to fully automate analysis of tokamak data to determine chains of events that lead to disruptions and to forecast their evolution. Disruption event chains related to global MHD instabilities, tearing modes, and many other off-normal events are identified. In an NSTX database exhibiting global MHD modes, resistive wall mode (RWM) and loss of boundary control events are found in all cases and vertical displacement events are found in over 90% of cases. Analysis shows 61% of RWM events occur within 20 conducting wall current diffusion times of the disruption. The remainders occurring earlier in time indicate minor disruptions. Insights are gained on the connection of mode activity to other events, including high Greenwald density fraction. Maximum amplitude of toroidal mode number n = 1 magnetic perturbations reached during disruptions and scaling with key parameters, important for ITER, are evaluated. Automated analysis of rotating tearing modes produce physical event chains leading to disruptions through mode slowing and subsequent locking. Analysis of NSTX and NSTX-U plasmas shows that the duration between mode bifurcation and locking varies with plasma conditions and can be shorter than the duration between mode locking and disruption onset. Global MHD instabilities such as external kink/ballooning modes or RWMs give the least amount of warning time before disruption. Kinetic RWM theory has shown high success in determining experimental mode marginal stability. A time-dependent reduced physics model of kinetic stabilization was created to forecast instability-induced disruptions. The initial model predicts instability 84% of the time for experimentally unstable cases with a relatively low false positive rate. *Supported by U.S. DOE grants DE-FG02-99ER54524, DE-SC0016614, and DE-AC02-09CH11466

Speaker: Dr Steven Sabbagh (Columbia University)

Sabbagh.S-EX-P6-26-Paper-rev2.pdf

Sabbagh.S-EX-P6-26-SummarySlide.pdf

479 Dynamic Neutral Beam Injection as a Mechanism for Plasma Control and an Actuator for Instability Drive

A novel capability has been added to the DIII-D neutral beam injection system, enabling in-shot variation of beam energy and current for the first time [1]. This new capability is now being explored as a tool for integrated control and optimization of equilibrium profiles and Alfvén eigenmode (AE) activity. The capability provides an alternative to the typically used pulse-width-modulation approach to controlling beam injection, and enables continuous variation of torque in the zero-torque regime. The capability also enables optimizing current drive and heating by injecting at lower energy during current ramp and at higher energy later in discharges. The first feedback algorithm making use of the new actuation approach has been experimentally tested, demonstrating stored energy and rotation control while addressing many of the challenges specific to using beam energy and current variation as an actuator. These challenges include constraints on the magnitude of beam voltage and current, slew rate limits on voltage changes, and lag between requested and achieve beam parameters. A real-time optimization-based control algorithm was developed that determines the voltage, current, and duty cycle required at steady state to maintain the optimal stored energy and rotation values, while accounting for the limits on voltage and current. The algorithm compensates the slow response of the voltage through fast adjustments of the current to more quickly track the required power and torque. The power and torque requests are augmented with a feedback term to improve energy and rotation target tracking. In a related experiment, a real-time ECE signal was used to detect AE mode activity and vary the NBI power through beam modulation based on feedback on the mode amplitude. This demonstration of AE mode control also showed that the ratio of the measured neutron rate to the classical predicted value, an indication of the effect of the AE mode on fast ion confinement, was changed through the variation of AE mode amplitude. The results of these two experiments motivate further development to integrate the new actuation and feedback approaches to control equilibrium parameters, including rotation and q, along with AE mode activity.

Supported by U.S.D.O.E. Contract No. DE-AC02-09CH11466 and DE-FC02-04ER54698.

[1] J. Rauch et al., Fusion Science and Technology 72, 3, (2017)

Speaker: Mr B.A. Grierson (Princeton Plasma Physics Laboratory)

Summary slide Boyer_IAEA2018_Summary_slide.ppt

480 Dynamics of Neon Ions after Neon Gas Seeding and Puffing into Tokamak Plasma

High Z Impurity seeding/puffing is an important topic as it is capable to provide radiative improvement of confinement and disruption mitigation in future tokamaks. Here, in this work, numerically and experimentally, we investigate the effect of low density 1% Ne gas (Z = 10, A = 20) seeding and also massive gas puffing. Two dimensional electrostatic interchange turbulence simulation has been done in the edge and SOL regions. The Ne ion density is found maximum in the edge region, which indicates inward motion of the ions. The polarization drift and turbulent eddies play a significant role for the inward motion. The numerical results have been compared with the results obtained from the Ne seeding experiments on the ADITYA. This experiment indicates several Ne lines of higher charged states. As Ne VII has an ionization potential of 157.9 eV, hence, a Ne penetration up to at least ~0.84 is achieved. Reduction of radially outward flux by the neon gas has been observed from the numerical simulations and also from the ADITYA experiments. In this work, these results will be compared. Simulation of massive neon gas puff has been done. Substantial cooling and modification of the plasma pressure gradient have been found.

Speaker: Dr Nirmal Kumar Bisai (Institute for Plasma Research, Bhat, Gandhinagar-382428, India)

onepage.pdf

481 ELMs onset triggered by mode coupling near rational surfaces in the pedestal

Investigations of pedestal evolution between edge-localized-modes (ELMs) in DIII-D provide strong evidence that coupling of modes located near rational surfaces close to the separatrix leads to the onset of an ELM. While the peeling ballooning model is the leading candidate for the ELM phenomenology, the triggering mechanism is not yet understood and remains one of the most outstanding challenges of both theoretical and experimental fusion science. In this work, the physical mechanism of the triggering of ELMs is studied on the DIII-D tokamak. We extract the dynamics of the most dominant modes localized in the pedestal during multiple inter-ELM periods. We observe a transition from a regime dominated at the beginning of the inter-ELM period by a single mode located near q=5 towards a more balanced organization between this mode and two secondary modes located near the q=6 surface just before the ELM onset. This redistribution suggests a transfer of energy which provides strong evidence that these secondary modes are triggering the ELM onset, because they are strongly coupled to the region extending to the separatrix. The radial expansion to the separatrix provides a channel for the expulsion of energy and particle, which is the ELM. The locality of these modes is determined through the spatial coupling between j_(||) and δn_e. While pedestal width growth has long been the leading explanation of the ELM onset, the results presented describe a different mechanism for ELM onset. In our explanation, the pedestal temperature and density gradients are clamped over multiple transport time scales and it is posited that the inter ELM fluctuations play a key role in the ELM onset. As shown above, the onset results from modes coupling between the q=5 & q=6 rational surfaces during the ELM cycle. We propose that such coupling opens up a channel from the pedestal top to the separatrix through which the energy to trigger the ELM is released. This work was performed under US DoE contract DE-AC02-09CH11466, DE-FC02-04ER5469, DE-FG02-08ER54984 and DE-FC02-04ER54698.

Speaker: Dr Ahmed Diallo (PPPL)

SummarySlideIAEA2018.pdf

482 En Route to High-Performance Discharges: Insights and Guidance from High-Realism Gyrokinetics

Although remarkable progress in ab initio nonlinear gyrokinetic plasma core turbulence studies has been seen in the last decade, some important open issues remain – e.g., in view of high performance discharges where magnetic fluctuations tend to reduce the turbulence levels and where the presence of fast ions may provide further significant stabilization enhancements. This effect was shown to lead to a significant reduction of ion temperature profile stiffness in JET [Citrin, PRL 2013] and was required to explain DIII-D quiescent H-modes [Holland, Nucl. Fusion 2012] as well as non-inductive ASDEX Upgrade (AUG) discharges [Doerk, Nucl. Fusion 2018]. Several questions immediately arise in this context: Are these - mainly local flux-tube simulation based – results modified by nonlocal effects in steep-gradient regimes? Can fast ion populations be used to control turbulent transport in burning plasmas? All of these questions culminate into this one: To which degree is core gyrokinetics able to reproduce observations from present-day experiments and predict future devices? In order to address this crucial task, comprehensive state-of-the-art validation studies with AUG fluctuations measurements will be presented as examples. Furthermore, studies for simplified equilibria [T. Görler, Phys. Plasma 2016] and high-beta AUG discharges will be shown confirming that the level of stabilization and threshold values for transitions between electromagnetic micro-instabilities like ion temperature gradient (ITG) driven and kinetic ballooning modes (KBM), may very well be affected by nonlocal effects. In addition, light will be shed on the improvements that can be expected by considering fast ion effects in electrostatic and electromagnetic simulations. Employing the gyrokinetic code GENE [F. Jenko, Phys. Plasmas 2000], a wave-fast ion resonance mechanism was found to be critical in describing corresponding JET discharges [A. Di Siena, Nucl. Fusion 2018]. While irrelevant to fusion-generated alpha particles which just act as diluting particles, it can be shown that cleverly tailored fast ion temperature (gradient) profiles may still offer pathways towards optimized plasma scenarios with substantial turbulence reduction. The predictions are further improved by studying the impact of more realistic fast ion models than the often employed equivalent Maxwellian backgrounds.

Speaker: Dr Tobias Görler (DeMPIPGarc)

Summary slide IAEA_FEC_2018_Goerler_TH-P6-5_slide.pdf

483 Enhancement of helium exhaust during suppression of edge localized modes by resonant magnetic perturbation fields at DIII-D

It is shown for the first time that global exhaust of helium, measured by effective helium particle confinement time (𝛕p,He), is improved during edge localized mode (ELM) suppression by resonant magnetic field perturbations (RMP) in high confinement (H-mode) ITER-shaped tokamak plasmas at DIII-D. An up to 40% reduction of 𝛕p,He during RMP-ELM suppression compared to ELMy H-mode discharges without RMP fields was measured using He test pulses in the upper outboard midplane. The ratio 𝛕p,He/𝛕E is reduced from 13 to 11 during RMP ELM suppression, showing that the improvement in He removal from the system exceeds the impact of RMP fields on energy confinement, bringing this ratio closer to the canonical threshold for a fusion reactor of 𝛕p,He/𝛕E<10.
To understand the cause of this important observation, we assess the changes to He confinement and exhaust in a three-reservoir model consisting of the core, plasma edge/SOL, and neutral reservoirs. Global He exhaust from the system depends on the exhaust from the confined plasma domain into the SOL and the neutral reservoir, where neutralized He is eventually removed by the pump. However, the removal rate (pumping efficiency) for He is low, and it recycles many times before being pumped. Therefore, retaining He in the plasma peripheral regions (SOL and neutral domain) without back-fueling of the plasma is vital for the He exhaust cycle.
Measurements of He and D2 neutral pressures in the pump plenum from Penning gauges show the partial pressure of He increases substantially more than that of D2 during RMP-ELM suppression, in comparison with the ELMing H-mode. This selective increase in He concentration suggests a preferential enhancement of He exhaust into the neutral domain, rather than a simple link to main species ‘pumpout’, and provides substantial evidence of strong He retention in the plasma periphery during RMP ELM suppression, which is a necessary condition to improve removal of He from the system. The He density in the edge confined region measured with charge exchange recombination spectroscopy also shows an enhanced rate of decay during RMP ELM suppression. These first-time findings are important for ITER, where application of RMP fields is planned for ELM control, as they suggest application of RMP ELM suppression could replace the impurity exhaust produced by the ELM events.

Speaker: Dr Edward Hinson (University of Wisconsin-Madison)

Summary SummarySlideHinson.pdf SummarySlideHinson.pptx

484 Error Field Impact on Mode Locking and Divertor Heat Flux in NSTX-U

Results from the 2016 NSTX-U campaign and the subsequent recovery effort have led to significant new insights regarding error fields in the NSTX-U experiment in particular, and in spherical tokamak configurations in general. During the experimental campaign, many L-mode discharges were found to be locked from the q=2 surface outward, indicating the presence of error fields. At the conclusion of the run campaign, extensive metrology was conducted on the primary vertical field (“PF5”) coils, and the center stack assembly, which includes the central solenoid and the center rod of the toroidal field (“TF”) coils. Error field models based on these measurements indicate that misalignment of the TF rod, while small, produces the largest error field among the sources considered. Plasma response modeling with IPEC and M3D-C1 finds that the TF error field remains the dominant source of resonant braking, despite the fact that the TF error field spectrum couples relatively weakly to the plasma, due to the large current in the TF rod and the proximity of the rod to the plasma. The plasma response to the TF error field is expected to depend significantly on the presence of a q=1 surface, since the TF error field is dominantly m/n=1/1. This is qualitatively consistent with results of several “compass” scans performed during the NSTX-U run campaign, which found that the optimal error field correction before and after the formation of the q=1 surface differed significantly. Interestingly, these discharges typically disrupted via locking of the 1/1 surface, since the 2/1 surface was often locked ab initio. It is found that certain characteristics of the TF error field present new challenges for error field correction. Specifically, the error field spectrum differs significantly from that of coils on the low-field side (such as the NSTX-U RMP coils), and does not resonate strongly with the dominant kink mode, thus potentially requiring a multi-mode correction. Finally, to mitigate heat fluxes using poloidal flux expansion, the pitch angle at the divertor plates must be small (~1 degree). It is shown that large error fields may result in unacceptable local perturbation to the pitch angle. Tolerances for coil alignments in the NSTX-U restart are derived based on both heat flux considerations and core resonant fields independently.

Speaker: Nathaniel Ferraro (Princeton Plasma Physics Laboratory)

Summary Slide

485 Extending the boundary heat flux width database to 1.3 Tesla poloidal magnetic field in the Alcator C-Mod tokamak

The boundary heat flux width ($λ_q$) is an important part of the power exhaust challenge in magnetic confinement fusion reactors. Understanding what sets $λ_q$ has largely been an empirical science [1], however physics understanding is progressing [3-6]. A database of $λ_q$ in H-mode indicated that the poloidal magnetic field ($B_p$) was the only significant parameter associated with the heat flux width: $λ_q~B_p^{-1.19}$ [1]. The maximum $B_p$ in the database was ~0.8 T, whereas ITER at 15 MA will be ~1.2 T.

C-Mod has been the only diverted tokamak capable of operating at reactor-relevant $B_p$, now with measurements up to 1.3 T. These new measurements in EDA H-mode clearly follow the inverse scaling of $λ_q$ with $B_p$ to values exceeding ITER-level. The heuristic drift (HD) model [4,5] has done a remarkable job of reproducing the trend and the magnitude of $λ_q$ in the database. The new high-field data from C-Mod are consistent with the HD model. Perhaps more importantly, the new data provide a benchmark for first principles models [6,7], one of which projects [6] to ~10 times larger $λ_q$ than the empirical $B_p$ scaling for ITER. In addition, we have assembled a database of $λ_q$ consisting of over 300 shots that span nearly the entire operating space of Alcator C-Mod (L-, H- and I-modes) under attached divertor conditions. As in earlier studies [8], $λ_q$ at fixed $B_p$ exhibit significant scatter that appears related to the core plasma confinement. We are presently exploring correlations of $λ_q$ with global and pedestal parameters; we will report on the latest results at this meeting. The database now includes a composite of measurements made by surface thermocouples and Langmuir probes. Improved spatial resolution and heat flux dynamic range over IR thermography allows for more accurate fits of $λ_q$ and resolving the role of transport into the private flux region. We find that the assumption of symmetric spreading of heat flux [1] is not appropriate under many conditions.

[1] T. Eich, et al., Nucl. Fusion 53 (2013) 093031. [2] R.J. Goldston, et al., Nucl. Fusion 52 (2012) 013009. [3] R.J. Goldston, J. Nucl. Mat. 463 (2015) 397-400. [4] C.S. Chang, et al., Nucl. Fusion 57 (2017) 116023. [5] B. Chen, et al., “Progress towards modeling…”, submitted to Phys. Plasmas. [6] B. LaBombard, et al., Phys. Plasmas 18 (2011) 056104.

Speaker: Dr Maxim Umansky

Brunner.D-EX-D-1-slide_summary.pptx

High-resolution heat flux width measurements at reactor-level magnetic fields and observation of a unified width scaling across confinement regimes in the Alcator C-Mod tokamak

486 Fast ITER-relevant low-disruptivity rampdowns in DIII-D and EAST

Recent experiments on DIII-D and EAST are developing the techniques and scientific understanding that ITER and future devices will need for safe, low-disruptivity shutdown. ITER needs options for reliable termination both in normal operation as well as in response to an off-normal event, where speed to soft landing is paramount. A large survey of ramp-down techniques in a variety of DIII-D plasma conditions shows disruptivity in fast ($I_p$ ramp-rates of 2-3 MA/s), diverted ramp-downs is similar or improved compared to historical, limited ramp-downs with $I_p$ ramp-rates typically ≤ 1 MA/s. The survey used the ramp-down phase of over 370 DIII-D discharges to develop improved soft-landing techniques scalable to ITER. The disruptivity is shown to be minimized by keeping neutral beam injection (NBI) power on for the duration of ramp-down, and at modest power levels roughly comparable to the average radiated power during shutdown. Experiments on ITER Baseline Scenario (IBS) plasmas have tested the limits of the planned ITER ramp-down as well as faster yet "full-bore" ramp-downs, in which the flat-top ITER shape is maintained through ramp-down. Disruptivity statistics for this scenario have been measured to inform ITER operation, and fast (2 MA/s), full-bore ramp-downs reduced the disruptivity to 25% from the historical rate of 58% using DIII-D's standard 1 MA/s, limited ramp-down method. The planned, shape-evolving (dropping elongation) ramp-down of the 15 MA ITER Q=10 scenario has been experimentally simulated at speeds scaling to the fastest ramp-down ITER is expected to be capable of (~60s [1]), and the scenario is found to be capable of maintaining the required $l_i$ < 1 during the H-mode phase of ramp-down while the elongation is reduced. Experiments on the EAST tokamak have likewise identified robust, fast, diverted ramp-down techniques using sustained lower hybrid (LH) power for the duration of ramp-down. Surveys of plasma current ramp-rate and LH power were conducted in the ramp-down phase of EAST discharges to complement the ramp-down survey performed on DIII-D. By continuing application of 2 MW of LH heating power, the fastest ramp-down yet on EAST of 0.5 MA/s has been demonstrated. This work was supported in part by the US Department of Energy under DE-FC02-04ER54698 and DE-SC0010685. [1] A.C.C Sips, et al 2015 Physics of Plasmas 22, 021804

Speaker: Dr Jayson Barr (General Atomics)

IAEA2018_Barr_SummarySlide.pdf

487 Fast wave experiments in LAPD in support of fusion

Recent work on ICRF physics at the Large Plasma Device (LAPD) at UCLA has focused on deleterious near-field antenna effects, such as RF rectification, sputtering, convective cells and power lost to the plasma edge. Plasma parameters in LAPD are similar to the scrape-off layer of current fusion devices. The machine has a 17 m long, 60 cm diameter magnetized plasma column with typical plasma parameters $n_e \sim 10^{12} – 10^{13}$ cm$^{-3}$ , $T_e \sim 1 – 10$ eV and B$_0 \sim 1000$ G. A new high-power ($\sim$150 kW) RF system and fast wave antenna have been developed for LAPD, enabling the generation of large amplitude fast waves. Evidence of rectified RF sheaths is seen in large increases ($\sim 10 \ T_e$ ) in the plasma potential on field lines connected to the antenna, and in copper deposition on plasma facing components due to sputtering at the antenna. The rectified potential scales linearly with antenna current. The rectified RF sheaths set up convective cells of local **E** x **B** flows, measured indirectly by potential measurements, and measured directly with Mach probes. At high antenna powers substantial modifications of the density profile were observed after the RF antenna is powered up. The density rearrangement is asymmetric with a decrease in plasma density near the top of the antenna and an increase near the bottom. The plasma density profile initially exhibits transient low frequency oscillations ($\sim 10$ kHz) and settles into a quasi-steady state profile for the remainder of the RF pulse. RF antenna current is constant during the pulse. The amplitude of the fast wave fields in the core plasma is modulated at the same low frequency, suggesting fast wave coupling is affected by the density rearrangement. At low antenna powers, the parasitic coupling to slow waves in the low density region in front of the antenna is being studied. Detailed wave field measurements show coupling to both the short wavelength slow wave and the long wavelength fast wave if the density at the antenna is low enough. Coupling to lower hybrid waves was demonstrated for a range of normalized frequencies, from $1 < f / f_{ci} < 30$. Performed at the Basic Plasma Science Facility, supported by the National Science Foundation and the Department of Energy.

Speaker: Dr Bart Van Compernolle (University of California, Los Angeles)

BVanCompernolle_summary_slide.pdf

488 Favorable Impact of RMP ELM Suppression On Divertor Heat Fluxes at ITER-like Conditions

RMP ELM suppression experiments at ITER-like conditions (shape, collisionality, RMP spectrum) in DIII-D show little splitting of the heat flux to the divertor targets, despite robust splitting in the particle flux. This lack of divertor heat flux splitting is a potentially important result for ITER because splitting of the divertor heat flux into multiple lobes displaced from the primary strike point could complicate heat flux handling during RMP ELM suppression in ITER and other tokamaks with tight divertor baffling. In DIII-D, strike point splitting is routinely observed in the divertor particle flux during RMP operation. The observed splitting is consistent with the toroidal mode number n of the perturbation, but the measured separation of the divertor particle flux lobes exceeds predictions of a vacuum model by factors of 3-5. Similar splitting in the heat flux profile would have serious consequences for heat flux handling during RMP ELM suppression in ITER. However, there is little impact of these particle flux lobes on the measured divertor heat flux. The large particle flux lobe separations present a challenge for plasma response modeling, because the predicted response using linear, resistive MHD simulations is dominantly a screening response, which should reduce the divertor lobe splitting below the vacuum model predictions.
Current ramps, which were limited in amplitude for a subset of RMP coils to be consistent with force limits on the RMP coils in ITER, were used to modify the divertor lobes from an n = 3 to an n = 2 pattern. The particle flux lobes changed during the RMP current ramps, but the heat flux profile was not affected, consistent with the lack of heat flux lobe structure. Possible synergistic effects of impurity gas injection and RMP current ramps were also examined using neon and argon gas injection into the ELM suppressed phase. Both gases produced stable radiating mantles between 0.95≤ Ψ_N≤1, a 60% radiated power fraction, and significantly reduced heat flux to both strike points while ELM suppression was maintained. These results show that RMP ELM suppression in ITER-like conditions is compatible with an impurity radiation-enhanced boundary.
This work is supported by the US Department of Energy under DE-FG02-07ER54917, DE-FG02-05ER54809, DE-FC02-04ER54698, DE-SC0012706, DE-AC52-07NA27344, DE-NA0003525, and DE-AC04-94AL85000.

Speaker: Dr Alberto Loarte (ITER Organization)

16x9_IAEA EX_P6_17_DMOrlov_summary_slide.pdf

IAEA EX_P6_17_DMOrlov_summary_slide.pdf

489 First Simulations of Turbulent Transport in the Field-Reversed Configuration

Experimental progress by TAE Technologies has led to successful suppression of MHD instabilities in field-reversed configuration (FRC) plasmas using C-2U and C-2W devices. Resultant particle and energy confinement times are on the order of several milliseconds, governed by micro-turbulence driven transport processes. Understanding these mechanisms is essential towards improved confinement and a viable FRC fusion reactor. Experimental measurements of low frequency density fluctuations in C-2 have shown that fluctuations of the FRC core and SOL exhibit distinct qualities. In the SOL, fluctuations are highest in amplitude at ion-scale lengths and exponentially decrease towards electron-scale lengths. In the core, fluctuations are overall lower in amplitude with a dip in the ion-scale lengths and a slight peak in electron-scale lengths. Using the Gyrokinetic Toroidal Code (GTC), local linear simulations of driftwave instabilities have found qualitatively similar trends. The SOL is linearly unstable for a wide range of length scales and pressure gradients. On the other hand, the core is shown to be robustly stable due to the stabilizing FRC traits of short field-line connection lengths, radially increasing magnetic field strength, and the large finite Larmor radius (FLR) of ions. To address micro-turbulence in a global FRC magnetic geometry that spans the separatrix, A New Code (ANC), a particle-in-cell code closely related to GTC, has been developed. Nonlocal cross-separatrix simulations show fluctuations spreading from the SOL to the core with fluctuations in the core saturating at levels an order of magnitude lower than in the SOL, consistent with experimental measurements. Turbulence simulations, domain limited to the SOL, show saturation without zonal flow is achieved at levels around e_phi/T_e ~ O(10^-2), and an inverse spectral cascade is observed. Recent calculations have been extended to more realistically simulate cross-separatrix turbulence. Initial global turbulence simulations show the evolution of the fluctuation spectrum to be comparable to the experimental measurements. In this paper, global turbulence simulations will be compared with experimental results from C-2 and C-2U. The effects of sheared flows, zonal flow, and kinetic electrons and ions on turbulent transport physics will also be reported.

Speaker: Prof. Zhihong Lin (UsUCALIrv)

Lau,Calvin -- IAEA FEC 2018 Turbulence Preprint.pdf

490 Flux-surface averaged radial transport in toroidal plasmas with magnetic islands

In toroidal magnetic confinement fusion research, one-dimensional (1D) transport models rely on one radial coordinate that labels nested toroidal flux surfaces. The presence of magnetic islands in the magnetic geometry does not impede making 1D transport calculations if the island regions are excluded and then, if necessary, treated separately. In this work we show a simple way to modify the flux-surface coordinate and corresponding metric coefficients when an island region is excluded. Comparison with the metrics obtained from Poincaré plots are shown, as well as applications to two types of plasma: Heliac (TJ-II, CIEMAT, Spain), where the geometrical effects alone cannot explain the experimental results when islands move throughout minor radius; and Heliotron (LHD, NIFS, Japan), where we estimate the effect of possible heat losses in flux-gradient relations.

Speaker: Dr Daniel López-Bruna (EsLNF)

LOPEZBRUNA_IAEA18_poster.pdf

lopezbruna-IAEA2018_procs.pdf

SummarySlide_P6-12.pdf

491 Global Alfvén eigenmode stability dependence on fast-ion distribution function

Global Alfvén eigenmodes (GAE) have been extensively studied on NSTX and with analytic and numerical modeling. Multiple GAE with a range of toroidal mode numbers are commonly observed in NSTX plasmas heated with neutral beams. Recently, analytic and numerical modeling has been used to very successfully model the suppression of GAE experimentally observed with the injection of high pitch (V||/V ≈ 1) resonant fast ions. In this paper we show that the scaling of the GAE frequency and toroidal mode numbers with toroidal field is qualitatively consistent with the analytic theory describing the Doppler-shifted ion cyclotron resonance (DCR) drive for the GAE. The GAE in NSTX and NSTX-U are excited through an ion cyclotron resonance with co-moving beam ions. The GAE propagate in the opposite, or counter, direction at frequencies down-shifted from the ion cyclotron frequency by the motion of the beam ions, that is, in the moving frame of the beam ions, the GAE frequency is up-shifted to the ion-cyclotron frequency. An analytic model of this resonant drive is presented in Ref. 1. An important result from this work is the prediction that resonant fast ions with k⊥ρ < 1.9 would be stabilizing (1.9 < k⊥ρ < 3.9 would provide drive). In this paper we use a simple dispersion relation for GAE combined with the DCR analytic theory to predict both the range of toroidal mode numbers and frequencies of unstable GAE. We find that this prediction is reasonably consistent with the observed experimental scaling.

Speaker: Dr Mario Podesta (Princeton Plasma Physics Laboratory)

492 Gyrokinetic Modeling of Turbulent Particle Fluxes towards Efficient Predictions of Density Profiles

A novel quasilinear particle transport model is constructed by joint analyses with gyrokinetic calculations and JT-60U experimental data. The new model deals with the diagonal (diffusion) and off-diagonal (pinch) transport mechanisms individually. Besides the decomposition, realistic particle sources from neutral-beam fueling are taken into account, which have not been discussed in earlier studies. Taking advantage of the features offered by the model, (i) the contribution from each transport mechanism to particle fluxes is quantitatively clarified, and (ii) a framework is developed, which enables us to predict the particle fluxes accurately and quickly, taking a neural-network-based approach. Moreover, (iii) a scaling formula is derived, considering linear zonal flows to understand mechanisms which determine the particle fluxes.

Speaker: Ms Emi Narita (National Institutes for Quantum and Radiological Science and Technology)

IAEAFECsummary2018_narita.pptx

493 High confinement in negative triangularity discharges in DIII-D

Discharges with negative triangularity (-delta) shape have been created in DIII-D with H-mode-like confinement (H98y2 = 1.2) and high normalized beta (beta_N = 2.6) with L-mode-like edge pressure profiles and no ELMs. These inner-wall-limited plasmas with delta = -0.4 had the same global performance as a positive triangularity (delta = +0.4) ELMing H-mode discharge with the same I_p, elongation, and area. For negative delta shots where up to 11 MW of NB heating and 3 MW of ECH heating were applied, the plasma attained high toroidal beta of 1.9% while staying in L-mode and without disrupting. Preliminary fluctuation data shows negative delta plasmas have lower levels of density and electron temperature fluctuations, typically reduced by 20%, in the outer region of the plasma, 0.7 < r/a < 1.0, compared to equivalent positive delta discharges. This reduction of turbulence is consistent with gyro-kinetic simulations and is attributed to a modification of the toroidal precession drift of trapped electrons exerted by the negative triangularity. Correspondingly, transport analysis indicates reduced ion and electron diffusivities for negative delta compared to the positive delta cases. Also, the positive triangularity discharges had 30-50% lower neutron rates as the identically heated negative triangularity ones, due primarily to impurity retention and deuterium dilution. These results show that negative triangularity is a viable candidate for reactor scenarios with its high confinement, ELM-mitigated characteristics plus a more economical and effective option for divertor placement. *Work supported by the US DOE under DE-FG02-97ER54415, DE-FG02-94ER54235, DE-FG02-08ER54999, DE-FG02-08ER54984 and DE-FC02-04ER54698.

Speaker: Dr Max Austin (UsIFS)

IAEA2018_CN391_EXP:6-6_AustinME_Summary.pdf

494 High Performance Double-null Plasmas Under Radiating Divertor and Mantle Scenarios on DIII-D

Enhanced radiation has been used to reduce divertor heat flux in high power, high performance (AT) double null divertor (DND) and near-DND plasmas in DIII-D, while at the same time maintaining acceptable energy confinement and particle control. Effective radiating mantle operation in high power AT plasma depended strongly on the location of electron cyclotron (EC) heating deposition, on impurity selection and its effect on triggering inimical MHD activity, and on the location where seed impurities are injected. Predictions by ELITE for ways to improve confinement and fueling in these high performance plasmas have been experimentally verified. The plasmas discussed here are characterized by: H98 = 1.4-1.7, betaN = 3-4, q95 ≈ 6, neutral beam plus EC power input P_in up to 15 MW, with EC providing up to 3.5 MW, dRsep = 6-25 mm. When the radial location of the ECH deposition was near the magnetic axis (e.g., rho_ech = 0.20), the radial profiles of both the injected impurity (e.g., neon) and carbon were mostly flat, while ECH deposition farther out (i.e., rho_ech = 0.45) produced profiles that were peaked. Analysis with the STRAHL transport code indicates a stronger inwardly-directed pinch for neon in the rho_ech = 0.45 case, while analysis for rho_ech = 0.20 indicates screening of neon from the central plasma. Using higher-Z seed impurities to form a radiating mantle increases deleterious MHD activity when applied to these AT DND plasmas. For example, when argon seeds were injected into these AT plasmas, the argon seeds triggered more deleterious MHD activity than the neon seed injection. Impurity selection, injection location, the ion grad-B drift direction, and details of scrape-off layer shaping strongly are shown to dictate where injected impurities can be most effectively pumped in DND and near-DND configurations. Finally, we show that conditions leading to improved performance in high power high performance regimes, which were predicted by ELITE code analysis, are largely supported by recent DIII-D experiments. These studies represent a continuing effort to experimentally identify potential issues related to adapting radiating mantle/divertor methods to high-powered AT DND plasmas. This work was supported in part by the US Department of Energy under DE-FC02-04ER54698, DE-AC05-00OR22725, DE-AC04-94AL85000, DE-AC52-07NA27344, and DE-FG02-07ER54917.

Speaker: Dr Thomas W. Petrie (General Atomics)

A28925 Petrie-IAEA summary viewgraph.pdf

495 High-Frequency Energetic Particle Driven Instabilities and their Implications for Burning Plasmas

Three high-frequency modes observed in the DIII-D tokamak have been identified as energetic particle instabilities driven unstable by anisotropic fast ions and runaway electrons. These modes could serve as control tools of the energetic particle distribution in fusion-relevant plasmas. (1) Whistler waves with w>>wci, excited by multi-MeV runaway electrons in a low-density (ne~1019 m-3) plasma, have been observed for the first time in a tokamak [1]. The waves occur in multiple discrete frequency bands in the 100-200 MHz range, with the measured whistler frequencies scaling with magnetic field strength and electron density, as expected from the whistler dispersion relation. Whistler activity correlates with runaway intensity (hard x-ray emission level), and a nonlinear interaction between the whistler instability and the runaway electron distribution function is observed. (2) Ion Cyclotron Emission (ICE) is readily excited across a wide region of operational space by kinetic instabilities at harmonics of the main ion wci. ICE is strongest in neutral-beam-heated plasmas with a clear dependence on beam geometry, with the highest emission levels with counter-current beams. This instability responds promptly to transient MHD events, including ELMs, fishbones and sawteeth. (3) Measurements of Doppler-shifted cyclotron resonant compressional Alfvén Eigenmodes (CAEs) below wci are consistent with many aspects of CAE theory, including an onset frequency strongly correlated with magnetic field and the observation of frequency splitting. CAEs are excited on DIII-D when the beam ions are near-Alfvénic, with onset frequencies of ~0.6fci. Consistent with recent hybrid MHD (HYM) simulations [2], a clear threshold behavior of the CAE instability is observed as the neutral beam density is varied at fixed energy. These high-frequency modes can potentially serve as much-needed control tools of the energetic particle distribution in fusion-relevant plasmas: Whistlers as a runaway relativistic electron control during a plasma disruption and ICE and CAEs as passive, non-invasive measurement of the fast-ion activity that could be used to optimize performance. This work was supported in part by the US Department of Energy under DE-FC02-04ER54698. [1] Spong et al., submitted to Phys. Rev. Lett. (2017). [2] Belova et al., Phys. Plasmas 24, 042505 (2017).

Speaker: Dr Kathreen Thome (Oak Ridge Associated Universities)

IAEA2018_Thome_SummarySlidev1.pptx

496 Implementing a finite-state off-normal and fault response system for robust disruption avoidance in tokamaks

A finite-state off-normal and fault response (ONFR) system is presented that provides the required supervisory logic for robust disruption avoidance and machine protection in tokamaks. Robust event handling is critical for ITER and future large tokamaks, where plasma parameters will necessarily approach stability limits and many systems will operate near their engineering limits. The ONFR system presented provides four critical features of a robust event handling system: sequential responses to cascading events, event recovery, simultaneous handling of multiple events and actuator prioritization. This system has been deployed during live experiments on DIII-D and KSTAR. In the most complex demonstration on DIII-D, the ONFR algorithm asynchronously applies “catch and subdue" electron cyclotron current drive (ECCD) injection scheme to suppress a virulent 2/1 neoclassical tearing mode, subsequently shuts down ECCD for machine protection when the plasma becomes over-dense, and enables rotating 3D field entrainment of the ensuing locked mode with synchronized ECCD deposition on the locked mode O-point to allow a safe ramp-down, all in the same discharge without user intervention. *Supported in part by the U.S. Department of Energy, Office of Science, Office of Fusion Energy Sciences, using the DIII-D National Fusion Facility, under Award DE-FC02-04ER54698. Work on KSTAR was supported by the Korean Ministry of Science and ICT under the KSTAR project and DOE Award DE-SC0010685.

Speaker: Dr Nicholas Eidietis (General Atomics)

Eidietis_IAEA_ONFR_Summary.pdf

497 Injection of Multiple Shattered Pellets for Disruption Mitigation in DIII-D

Experiments on DIII-D have injected multiple shattered pellets at different toroidal locations for the first time, as is planned for the ITER disruption mitigation system. Systematically varying the relative timing of the two pellets suggests that simultaneously injected pellets may impact the assimilation of each other, altering the resulting disruption characteristics compared to that due to a single pellet injecting similar neon quantities. Thermal quench (TQ) radiation fractions measured near the injection are reduced with the dual pellets contrary to TQ radiation fractions measured away from the injection ports which do not have a clear difference between single or dual pellet injections. This asymmetric reduction in radiation fraction indicates an overall reduction in the global radiation fraction and that possible radiation asymmetries may be reduced with dual pellet injection. Global disruption mitigation properties, such as the current quench duration, is found to increase when the pellets enter the plasma simultaneously compared to single shattered pellet injections with similar neon quantities. The similar reduction in mitigation of current quench loads is consistent with the observed reduction in TQ mitigation. The time between initial pellet injection and thermal quench onset (plasma cooling duration) is shorter when both pellets are injected simultaneously compared to a single pellet. The faster shutdown with two pellets could be due to the "head start" in the toroidal and poloidal spreading of impurities due to injecting the pellets at different toroidal locations -- effectively cooling multiple flux tubes simultaneously. The lower cooling duration may also limit the amount of the neon delivered by the shattered pellet into the plasma prior to the end of the TQ since the shattered pellet plume takes on the order of a few milliseconds to be completely in the plasma. These results suggest that changes in the spatial distribution of the initial impurity injection can impact the evolution of the fast shutdown, indicating that 0D treatments of disruption mitigation metrics are not fully sufficient. This asymmetric reduction in radiation fraction indicates an overall reduction in the global radiation fraction and that possible radiation asymmetries may be reduced with dual pellet injection.

Speaker: Dr Jeffrey Herfindal (Oak Ridge National Laboratory)

Summary Slide IAEA_summary_slide_Herfindal_v5.pptx

498 Inter vs. Intra-ELM Tungsten Erosion and Transport from the Divertor in DIII-D High-Performance H-mode Discharges

Measured intra-ELM (during ELMs) tungsten erosion profiles in the DIII-D divertor, acquired via W-I spectroscopy with high temporal and spatial resolution, are consistent with OEDGE+SDTrim.SP modeling including measured ion saturation currents and ion impact energies. If pedestal temperature rather than divertor conditions are used as input, quantitative agreement is observed, for the first time, between the Fundamenski-Moulton 'free-streaming' (FMFS) model predictions of how W source scales with ELM deposited energy density when broadening of the divertor heat flux footprint and enhanced target electron densities (e.g., via increased neutral recycling) are taken into account. Consistency is observed between this new FMFS-SDTrim.SP model and experimental measurements of intra-ELM W sourcing across a range of ELM frequencies/sizes, except for ELMs with very low energy density. An interpretive model for the time evolution of the W physical sputtering rate during ELMs was also developed including impurity and main ion sputtering. This model reveals that both D and C contribute substantially to W sourcing during ELMs in the DIII-D divertor because the average ion impact energy increases from below to substantially above the energy threshold for D$\rightarrow$W sputtering. The measured W sputtering profiles are well matched to this model with a 2% C$^{2+}$ fraction, a factor of 2 higher than in the inter-ELM (between ELMs) phase. This work represents unique progress towards a predictive model to link pedestal conditions to the ELM-induced divertor W impurity source. Such models can be utilized in ITER and beyond to develop and optimize mitigation strategies for minimizing high-Z accumulation in the core. Supported by the US DOE under DE-FC02-04ER54698.

Speaker: Dr Tyler Abrams (General Atomics)

Abrams_IAEA18_summaryslide.pptx

499 Investigation of fast particle redistribution induced by sawtooth instability in NSTX-U

The effects of sawtooth on fast ion transport have been studied in reproducible, 2 seconds long sawtoothing L-mode discharges during the 2016 experimental campaign on National Spherical Torus Experiment Upgrade (NSTX-U). Experimental observations through Solid State Neutral Particle Analyzer (SSNPA) and Fast-Ion D-alpha (FIDA) diagnostics show that passing particles within the measured energy range are strongly redistributed from the plasma core to the edge, whereas trapped particles are weakly affected. The effect of sawteeth is clearly seen as a significant reduction of the signal from passing particles inside the sawtooth inversion radius and a corresponding increase at outer radii. Modeling with the standard sawtooth models available in the TRANSP code reproduces the experimental neutron rate drops with the properly chosen model’s parameters. However, the FIDA simulation using the plasma profiles and fast ion distribution from the TRANSP simulation does not agree with the experimental measurement. A likely cause of the disagreement between experiments and simulations is that the sawtooth model in TRANSP does not take into account the different effect of sawtooth crash on fast ions with different orbit type and energy. Therefore a more comprehensive and improved model for quantitative simulations needs to be developed to interpret sawtoothing discharges more reliably including the characteristics of fast ion such as energy, toroidal angular momentum and pitch angle that affect the redistribution of fast ions in phase and real spaces. As a first step of the development of the improved sawtooth model, simulations using the Hamiltonian guiding center code ORBIT have been carried out. The simulation results confirm the experimental observation that fast ions are redistributed by sawtooth crash both in phase and real space depending on their orbit type and energy. In real space, passing particles in the core region are expelled outside the q=1 surface while trapped particles do not experience significant effects from sawtooth crash. The initial interpretative TRANSP simulation using the so-called kick model based on the ORBIT modeling result shows improvement of fast ion redistribution before and after a sawtooth crash but the neutron rate still has discrepancy compared to the experimental measurement.

Speaker: Dr Doohyun Kim (Princeton Plasma Physics Laboratory)

500 Ion and Electron Temperature Predictions based on Thailand Tokamak Plasmas using CRONOS Code

This work uses CRONOS integrated predictive modelling code to simulate ion and electron temperatures of plasma scenarios based on a future Thailand tokamak. This small tokamak is planned to be installed at Thailand Institute of Nuclear Technology (TINT), under the collaboration of the Center for Plasma and Nuclear Fusion Technology (CPaF). The plasma transport includes both neoclassical, via NCLASS module, and anomalous transports, via Mixed Bohm/gyro-Bohm module. The boundary condition for the thermal transport equation is set at the top of the pedestal where pedestal temperature is calculated based on scaling law. No external heating is given in these simulations so the plasmas remain only in L-mode. A simple electron density profile is given for all simulations with central value around 10-19 m-3. Effects of both plasma current and toroidal magnetic field on ion and electron temperatures are investigated. It is found that central electron temperature ranges from 200 to 410 eV, whereas ion temperature ranges from 120 to 170 eV. Evidently, both temperatures are more sensitive on the change of plasma current than that of toroidal magnetic field.

Speaker: Dr Boonyarit Chatthong (Department of Physics, Faculty of Science, Prince of Songkla University)

501 Kinetic Simulation Studies on Multi-ion-species Plasma Transport in Helical Systems

The first comprehensive analyses of kinetic simulations for anomalous and neoclassical transport of steady state multi-ion-species plasmas including impurity ions in helical systems are performed by gyrokinetic and drift-kinetic approaches. To design the fusion reactors, the transport phenomena of plasma particles and heat need to be quantitatively predicted, and numerical simulation approaches based on the kinetic frameworks are powerful for that purpose. Recently, it becomes able to validate the kinetic simulation results against the experimental observations for the plasma temperature and density profiles with the experimental errors taken into account. Furthermore, studies on the transport of the multi-ion-species plasma are strongly demanded for predicting the performances of the burning plasma in the ITER, future reactors, and also stellarators such as the Large Helical Device (LHD). In high ion temperature plasmas with hollow impurity density profiles heated by neutral beam injection (NBI), we find that the turbulent contribution of the carbon impurity particle flux remains to be directed inward radially within the allowable ranges of the plasma temperature and density profiles, while the neoclassical ion fluxes can change due to the generated radial electric field ($E_{\rm r}$) and the external momentum sources. Even for the case of the negative $E_{\rm r}$, the neoclassical carbon flux can be directed outward when the inward-directed current is imposed sufficiently by the co-injected heating beam. These findings contribute deeper understandings of the hollow profiles in the LHD impurity hole plasmas in terms of fully kinetic framework.

Speaker: Dr Masanori Nunami (National Institute for Fusion Science)

1page_slide_Nunami.pdf

502 Machine learning for disruption warning on Alcator C-Mod, DIII-D, and EAST Tokamaks

We find that disruption prediction using machine learning (ML), trained on large databases containing only plasma parameters that are available in real time on C-Mod, DIII-D, and EAST, differ substantially in performance among the three machines, implying that a universal real time disruption warning algorithm may be problematic. This could have important implications for disruption prediction and avoidance on ITER, for which development of a training database of disruptions may be infeasible. Whether or not disruption prediction can be improved by incorporating additional real time measurements, or with more sophisticated AI methods, is unclear. The database for each tokamak contains parameters sampled at ~$10^6$ times throughout ~$10^4$ discharges, disruptive and non-disruptive, over the last 3-4 years of operation. We find that a number of parameters (e.g. $P_{\rm rad}$/$P_{\rm input}$, $\ell_{\rm i}$, $n$/$n_{\rm G}$, $B_{n=1}$/$B_{\rm T}$) exhibit changes as a disruption is approached on one or more of these tokamaks. However, the details of these precursor behaviors are markedly different on each machine. We use a shallow ML method known as Random Forests, applied to a binary classification scheme. We define the two classes as "*close to a disruption*” and "*far from a disruption or from a non-disruptive shot*”. The threshold time that divides "close” from "far” is determined by optimising the classification prediction accuracy for each machine. We find that the timescales of disruption warning behavior are very different for the different machines, and that the fraction of correctly predicted disruption samples varies considerably, ranging from 74% for DIII-D, to just 35% for C-Mod. For C-Mod in particular, it is difficult to predict upcoming disruptions more than just a few milliseconds in advance. This work supported in part by: US DoE Grants DE-FC02-99ER54512, DE-SC0010720, DE-SC0010492, DE-FC02-04ER54698, DE-SC0014264 National Natural Science Foundation of China Grants 11475002, 11775262, 11475224, 11575247, 11475225, 11775266 and 11505235 National Magnetic Confinement Fusion Science Program of China Grants 2014GB103000 and 2015GB102004

Speaker: Dr Robert Granetz (MIT)

Granetz.R-EX_P6-20_summary_slide.pdf

503 Measurements of high-Z divertor impurity sourcing and divertor leakage using isotopic tungsten tracer sources in DIII-D

DIII-D carried out experiments using novel, isotopic tungsten (W) tracer sources in the outer divertor and has characterized how the W leakage from this region depends on botz the exact source location and ELM behavior. The W sources are toroidally-symmetric and poloidally-localized to two regions: (1) the outer strike point (OSP), a natural-W source; and (2) the far-target, i.e., 3-5 heat flux widths from the OSP, a W-182 source. With the use of a dual-faced collector probe (CP) in the main SOL near the outside midplane (OMP), it is found that the far-target W source has the smallest upstream deposition efficiency on the CP, i.e. divertor leakage, with high input power and small ELMs; conversely the far-target divertor leakage is highest with large ELMs. Additionally, without ELMs, it is also found that large deposition asymmetries on the opposite CP faces are consistent with model predictions of W accumulation in the near-SOL at the tokamak crown region. This unique experimental setup, together with source (W-I) and core spectroscopic measurements, provide information on the transport link between different W source locations within the divertor and the W content of the plasma outside the divertor, i.e., divertor leakage. These studies are elucidating the physics driving high-Z divertor impurity sourcing and leakage, both with and without ELMs, and are shedding light on this the weakest link, to date, in the chain connecting wall impurity sources to core impurity levels in MFE devices, like ITER. Work supported by US DOE under DE-FC02-04ER54698.

Speaker: Dr Ezekial Unterberg (Oak Ridge National Laboratory)

Summary Slide Unterberg-Sumary_Slide_EX_P6-16.pptx

504 Neural-network accelerated coupled core-pedestal simulations with self-consistent transport of impurities

An integrated modeling workflow capable of finding the steady-state solution with self-consistent core transport, pedestal structure, current profile, and plasma equilibrium physics has been developed, validated against several DIII-D discharges, and used to perform predictions for a 15 MA D-T ITER baseline scenario. Key features of the proposed core-pedestal coupled workflow are its ability to self-consistently account for the transport of impurities in the plasma, as well as its use of machine learning accelerated models for the pedestal structure, the neoclassical bootstrap current, and for the turbulent and neoclassical transport physics. Self-consistent coupling of physics-based models (or their machine-learning accelerated counterparts) is of great importance since it reduces the number of free parameters and assumptions that are used in the simulations, thus greatly improving the reliability of our numerical forecasts. The results presented in this paper provide supporting evidence that neural network based reduced models are indeed capable of breaking the speed-accuracy trade-off that is expected of traditional numerical physics models, and can provide the missing link towards whole device modeling simulations that are physically accurate, robust, and extremely efficient to run. Work supported in part by the US Department of Energy under Contract Nos. DE-SC0017992 (AToM), DE-FG02-95ER54309 (GA theory), DE-FC02-06ER54873 (ESL), and DE-FC02-04ER54698 (DIII-D). This research used resources of the National Energy Research Scientific Computing Center (NERSC), a DOE Office of Science User Facility supported by the Office of Science of the U.S. Department of Energy under Contract No. DE-AC02-05CH11231.

Speaker: Dr Orso Meneghini (General Atomics)

505 Nonlinear gyrokinetic analysis of linear Ohmic confinement to saturated Ohmic confinement transition

One of the long lived conundrums in ohmically heated plasmas is that the energy confinement time τ_E shows a transition from a linear regime proportional to the density (LOC) to a saturation regime (SOC) weakly dependent on the density. In the viewpoint of the first principle nonlinear global gyrokinetic simulations, we here present an investigation of LOC to SOC transition for the first time. In this study, by varying a single parameter plasma density, the confinement time estimated by τ∝1⁄χ_eff shows a transition from a linearly increasing regime to a saturation regime as the plasma density increases. The effective transport diffusivity is defined as χ_eff≡(n_e χ_e ∇T_e+n_i χ_i ∇T_i)/(n_e ∇T_e+n_i ∇T_i ), where n_(e(i)),T_(e(i)) and χ_(e(i)) are density, temperature and heat diffusivity for electron (e) and ion (i). The above nonlinear result follows the trend from the mixing length quasilinear estimation for the heat transport. A transition of trapped electron dominant heat transport from TEM to ion dominant heat transport from ITG is observed when the LOC to SOC transition occurs. In the simulations, the Coulomb collision operator for ion-ion collision and the pitch-angle scattering operator for electron-ion collision are included. The physical effects of the collisions in the LOC to SOC transition can be understood by analyzing the phase space dynamics. Physics of intrinsic rotation reversal [1,2] and E×B staircase [3], both of which were found to have close relations with LOC-SOC transition, will be discussed. [1] J. E. Rice, et al., PRL 107, 265001 (2011) [2] Y. J. Shi, et al., Nucl. Fusion 57, 066040 (2017) [3] G. Hornung, et al., Nucl. Fusion 57, 014006 (2017)

Speaker: Dr Lei Qi (National Fusion Research Institute of South Korea)

506 Numerical simulation of high neutron rate JET-ILW DD pulses in view of extension to DT experiments

This paper is focused on the simulation of JET ELMy H-mode pulses pertaining to the baseline scenario with medium-high electron density, n_e, and auxiliary power, P_aux, in excess of 30 MW. The auxiliary heating is provided mostly by NBI, while ICRF heating does not exceed 5 MW. We have considered two pulses (Ip=3 MA, Bt= 2.8 T) at n_e = 6.5-7x10^19 m^-3 which show very high neutron rates and are characterized by Ti/Te >1 with T_e(0) about 7 KeV. The density was provided either by pellet injection or by gas puffing. The thermal stored energy is 8.1-8.7 MJ, the temperature at the plate, T_e,pl, is 25-35 eV and the total power to the target is 15-17 MW. These pulses are slightly Ne seeded (c_Ne about 0.2 %) with radiated power fraction, f_rad= 0.40. Once the simulations of the experimental pulses have been established, extrapolation to DT plasmas has been done, keeping unchanged the code inputs. We have used the COREDIV code, self-consistent with respect to the core-SOL as well as to impurities-main plasma. In spite of some simplifications, the exchange of information between the core (1D) and the SOL (2D) module renders this code quite useful when, as in the case of the JET ILW, the interaction SOL-core is crucial. Extrapolation to DT plasmas depends on the assumptions for tau*_He/tau_E and for the impurity species considered. Although the DT simulations are ongoing, some comments can be made at this stage. Keeping in the DT simulations n_e and P_aux at the same level as in the corresponding experimental pulses the resulting P_alpha is between 0.7 and 1.1 MW, depending on the assumptions made, with practically unchanged T_e,pl and power to the target. Increasing P_aux to 41 MW, P_alpha increases only slightly while the power to the plate is 27 MW with T_e,pl = 70 eV. Recalling that in our simulations only P_alpha arising from thermal reactions is accounted for, these preliminary results indicate that strike point sweeping might not be sufficient to control the heat load to target plates at peak plasma performance for 5 s and additional impurity seeding might be necessary. As next step, Ip will be increased to 4 MA, keeping unchanged either n_e or n_e /n_Gw.

Speaker: Mr Giuseppe Telesca (IPPILM Poland)

Telesca IAEA slide TH P6-24.odp

507 Observation of efficient lower hybrid current drive at high density on Alcator C-Mod

Efficient lower hybrid current drive (LHCD) at high plasma density has been demonstrated on Alcator C-Mod for the first time with the reduction in the Greenwald fraction by raising the plasma current. In order to attain, steady-state advanced tokamak operation, efficient off-axis current drive is required. LHCD is highly desirable because it has the highest efficiency of all technologies presently available. However, the LHCD experiment on C-Mod has shown a loss of anomalous current drive efficiency above $\overline{n}_{crit} ≈ 1\times 10^{20} \rm{m}^{-3}$, which prohibited an access to advanced tokamak operation [1]. Parasitic wave interactions in the edge/SOL region may account for the density limit behavior [2-4] because the scrape-off-layer density profile becomes broadened with an increased level of blobby transport with the increase in the Greenwald fraction [5]. In the most recent C-Mod experiments, the operating plasma current was raised up to 1.4 MA in order to minimize the SOL width at $\overline{n}_{crit} ≈ 1.4\times 10^{20} \rm{m}^{-3}$. The injected LH power (600 kW) produced a loop voltage drop of 0.2 V, consistent with engineering efficiency found at low densities. The non-thermal Bremsstrahlung emission rate was increased by more than two orders of magnitude compared to the lower current case. Parasitic interactions of wave with the SOL plasma are largely suppressed, indicated by the spectrum measurement. The new experimental results indicate that efficient current drive at a reactor density can be attained with proper management of the edge/SOL plasma. They support a proposal to place LH launchers at the high-field-side (HFS) of the tokamak in a double null configuration [6]. In this case, the density shoulders and blobby transport phenomena are absent in the HFS SOL. Efficient current drive may be attained even at high Greenwald fraction by avoiding parasitic edge/SOL wave interactions. [1] G. M. Wallace, et al, PoP 17 (2010) 082508;[2] S. G. Baek, et al, Nucl. Fusion 55 (2015) 043009;[3] I. C. Faust, et al, PoP 23 (2016) 056115;[4] S. Shiraiwa, et al, AIP 1689 (2015) 030016;[5] B. LaBombard, et al, PoP 15 (2008) 056106;[6] B. LaBombard, et al, Nucl. Fusion 55 (2015) 053020; Work supported by the U.S. Department of Energy, Contract No. DE-FC02-99ER54512 on Alcator C-Mod, a Department of Energy Office of Science user facility.

Speaker: Seung Gyou Baek (MIT PSFC)

summary_slide.pdf

508 Observation of Multiple Helicity Mode-Resonant Locking Leading to a Disruption on DIII-D

Experimental evidence of the formation of multiple helicity island chains during the mode locking phase preceding plasma disruption is providing a clear picture for the understanding of locked-mode triggered disruptions. This emerging picture uses measurements from a new dual soft x-ray (SXR) tangential imaging system that measures localized internal perturbations in combination with local temperature profile flattening. In mode locking experiments with low-beta (β_N~0.5), inner-wall limited L-mode discharges, a low-order rational surface (2/1) locks and reduces the plasma rotation across the edge region allowing higher order island chains (3/1, 4/1) to form. These signatures are measured by SXR imaging that show the presence of resonant perturbations that have been reproduced consistently with synthetic modeling and local temperature flattening measured by Thomson scattering. The edge 4/1 island cools rapidly by extending into the boundary region. On a slower time scale over 300ms, both the 2/1 and 3/1 islands widen. This growth leads to eventual island overlap and enhanced stochastic transport that allows a cold boundary region or cold pulse to penetrate into the core resulting in a rapid loss in thermal energy and plasma collapse. The observed growth of multiple island chains and evolution of edge cooling are successfully reproduced by a non-linear simulation (TM1 code) using a single fluid model without radiation effects. In this picture, the formation and slow widening of multiple helicity island chains leads to a locked mode disruption. This work was supported by the US DOE under DE-AC05-00OR22725, DE-FC02-04ER54698, DE-AC02-09CH11466, and JSPS KAKENHI Grant Number JP26249144.

Speaker: Morgan Shafer (Oak Ridge National Laboratory)

summary_slide_EX:P6-24 .pdf

509 Parallel Energy Transport in Detached DIII-D Divertor Plasmas

A comparison of experiment and modeling of detached divertor plasmas in DIII-D is examined in the context of parallel energy transport due to electron conduction and plasma convection in order to validate and improve models used for divertor design. Power balance analysis is carried out to determine parallel heat flux and energy dissipation as a function of distance from the divertor target. The relative fractions of conductive and convective heat flux are determined from Thomson scattering measurements of the divertor parallel Te gradient. Modeling with the fluid code SOLPS is found to underestimate divertor heat flux radiative dissipation due to two effects, 1) lower values of parallel convection than inferred from experiment and 2) lower impurity radiation than measured experimentally at similar values of Te. Resolution of these discrepancies is expected to improve accuracy and confidence for predictive modeling of divertor operation in future devices. Work supported by the US DOE under DE-FC02-04ER54698, DE-AC52-07NA27344, DE-FG02-07ER54917, DE-AC05-00OR22725, DE-AC02-09CH11466, and DE-AC04-94AL85000.

Speaker: Mr Anthony Leonard (General Atomics)

Summary_page.pdf

510 Parametric study of the impurity profile in the Thailand tokamak

A small tokamak is planned to be installed in Thailand at Thailand Institute of Nuclear Technology (TINT), Ongkarak campus in Nakorn Nayok, under the collaboration of the Center for Plasma and Nuclear Fusion Technology (CPaF). One of the great challenges subject in operating this tokamak is to gain better understanding of the impurities behavior because the impurities are responsible for the large power losses. Therefore, the studies of the impurity behaviors are conducted for the commissioning stage of Thailand tokamak. In this work, the spatial density distribution over all ionization states of helium, carbon, and oxygen have been calculated using the assumption of steady-state plasma under the relevant plasma scenarios that will be operated using Thailand tokamak. Additionally, the prescribed transport coefficients of charge number on neoclassical convection velocity and simplified turbulent transport coefficient effect are taken into account of this model. The quantification of Zeff has been carried out to characterize the impurity content of plasma. Finally, the impurity radiated power have been extracted using ADAS database of the global spectral line and continuum radiative coefficient. Due to the low charge number (Z) of interested impurities, the obtained power loss occurs mostly in the region near the plasma edge. It is found that when the plasma current is increased, the radiated power peak shifts toward the plasma edge. The calculation in this work provides significant contribution in commissioning and operating the Thailand tokamak to be available in various applications.

Speaker: Dr Siriyaporn Sangaroon (Mahasarakham University)

511 Particle Transport from the Bottom Up

Exploration of particle transport behavior in multiple devices shows the importance of turbulence in determining particle confinement and the density profile. Behavior on CMOD indicates that as plasma parameters approach ITER, the pedestal and SOL become increasingly opaque. H-mode experiments with density pedestals approaching $4 \times 10^{20}$ $m^{-3}$, heated with the maximum auxiliary power available, find that increasing deuterium puffing by a factor of ~2 doubles the SOL density while having <10% effect on pedestal density and core particle inventory. This suggests that high opacity pushes the neutral fueling profile into the SOL, leaving the pedestal density profile to be determined by plasma transport and an inward pinch. Similarly, studies on JET and DIII-D show that the inward pinch plays a crucial role in explaining the time dependent density changes when additional gas fueling is injected. Interestingly, neutral particle fueling does not play a direct role in pedestal density increases since COCONUT (core/edge integrated) modeling shows that the particle source inside the separatrix reduces when gas fueling increases because of higher SOL opacity. Where fueling and opacity play an important role at the plasma edge, in the core particle confinement is strongly affected by changes in turbulence. For example, during strong electron heating in low density H-mode plasmas on DIII-D a strong decrease in particle confinement is observed. This is linked to an increase in ITG drive from ρ~0.6 to ρ~0.8, which causes an increase in density fluctuations at all scales and results in a density pump-out. We find that where the temperature profiles are fairly insensitive to changes in ExB shear, particle confinement is directly linked to increases and decreases in ExB shear. In the core, we observe that the role of NBI fueling on the density profile cannot be neglected in current machines and that local gradients are directly linked to the turbulence frequency. These results indicate that in burning plasma conditions, opaque SOLs may not result in the collapse of the density pedestal owing to the inward particle pinch at the edge, and that a larger ExB shear will be beneficial to higher particle confinement. This work is supported by the US DOE under DE-SC00078801,2, DE-FG02-08ER549842, DE-AC05-06OR231003, DE-FC02-04ER54698, and DE-SC0012469.

Speaker: Prof. Saskia Mordijck (The College of William and Mary)

512 Physics of fast component of deuterium gas jet injection in magnetized plasmas

Plasma fueling with higher efficiency and deeper injection is crucial to enable fusion power performance requirements at high density for next generation devices such as ITER. Compared to pellet injection fueling method, it penetrates shallower for the fueling methods of supersonic molecular beam injection (SMBI) and gas puffing (GP). SMBI is one method of deuterium gas jet injection. Fast component (FC) of deuterium gas jet injection has been widely observed in the HL-2A experiment for several years but never been simulated and well understood. It is the first time that simulations of FC with trans-neut module of BOUT++ code are well validated with the HL-2A experimental measurements, in this paper. Simulation results are consistent with the experiment. The real HL-2A experimental profiles of plasma density and temperature are applied as the initial profiles in the simulation. Both the spatial and temporal evolution of Dα intensity is calculated self-consistently in the simulation by using Atomic Data and Analysis Structure (ADAS) database. The mechanism of FC is revealed. The plasma blocking effect on the FC penetration is also simulated and validated.

Speaker: Dr Zhanhui Wang (Southwestern Institute of Physics)

summary slide ZHWang TH-P6-22.pptx

513 Physics-model-based Real-time Optimization for the Development of Steady-state Scenarios at DIII-D

Recent and ongoing experiments on DIII-D demonstrate the potential of model-based real-time optimization for the realization of advanced steady-state scenarios by tightly regulating the $q$ profile and $\beta_N$ (or the plasma energy $W$) simultaneously. A primary goal for the DIII-D research program over the next five years is to develop the physics basis for a high $q$ ($q_{\text{min}}>2$), high $\beta_N$, steady-state scenario (fully relaxed plasma state where the current is entirely noninductive) that can serve as the basis for future steady-state burning plasmas. Various approaches are being considered to maximize both the bootstrap current and the noninductive current-drive contributions, so that fully noninductive ($f_{NI} = 1$) discharges can be obtained for several resistive current diffusion times. It is anticipated that the upcoming upgrades to DIII-D, including an additional off-axis neutral beam injection (NBI) system, will provide sufficient auxiliary current drive to maintain fully noninductive plasmas at high $\beta_N$. However, much work is still necessary to investigate MHD stability, adequate confinement, and early achievement and sustainment of the steady-state condition. The capability of combined $q$-profile and $\beta_N$ control to enable access to and repeatability of steady-state scenarios for $q_{\text{min}}>1.4$ discharges has been assessed in DIII-D experiments. To steer the plasma to the desired state, a model predictive control approach to both $q$-profile and $\beta_N$ regulation numerically solves successive optimization problems in real time over a receding time horizon by exploiting efficient quadratic programming techniques. A key advantage of this control approach is that it allows for explicit incorporation of plasma-state/actuator constraints to prevent the controller from driving the plasma outside of stability/performance limits and obtain, as closely as possible, steady state conditions. Experimental results demonstrate the effectiveness of the real-time optimization scheme to consistently achieve the desired scenarios at predefined times and suggest that control-oriented model-based scenario planning in combination with real-time optimization can play a crucial role in exploring stability limits of advanced steady-state scenarios.

Speaker: Prof. Eugenio Schuster (Lehigh University)

IAEA18_LU_Schuster_1SlideSummary_INDICO.pdf

514 Progress in the ITER Integrated Modelling Programme and the ITER Scenario Database

The ITER Integrated Modelling & Analysis Suite (IMAS) is the software infrastructure that is being developed using expertise from across the research facilities within the ITER Members to meet the needs of the ITER Integrated Modelling Programme. It builds around a standardised representation of data described by a Data Dictionary that is both machine independent and extensible. Machine independence is important for allowing tools and workflows developed in IMAS to be tested on existing devices, whilst extensibility allows the Data Dictionary to grow and evolve over time as more and more Use Cases are addressed. In addition to providing all the scientific tools for the scientific exploitation of ITER once operations start, IMAS also has a role to play during the construction phase by providing simulation data to support systems design, in particular for diagnostics, heating, fuelling and control systems. Recently an IMAS database of ITER simulations has started to be developed and populated to help manage the exchange of physics data with ITER collaborators and Domestic Agencies. The database is being populated through a combination of translating existing data and running new simulations. The scenario simulation codes used to initially populate the database are ASTRA, CORSICA, DINA, JINTRAC, and METIS. Additional data structures consistently describing other aspects of these scenarios, for example the fast ion distribution functions, are being added to the database upon request to facilitate the design of specific systems. The scenarios for all stages of the ITER Research Plan are represented in the database and are at least populated with a description of the plasma equilibrium and profiles in the core of the plasma. This database is accessible by all ITER contributors through the IMAS Access Layer, either for visualisation or as input to IMAS-adapted workflows and simulation codes. Subsequently generated data can be stored in the database subject to acceptance criteria and provenance requirements being met. The capabilities of the final implementation of the database, including strict acceptance and validation procedures and full provenance tracking for all entries will be discussed in the paper.

Speaker: Dr Simon Pinches (ITER Organization)

Pinches - IMAS Summary Slide - IAEA FEC 2018.pptx

515 Quantification of Radiating Species in the DIII-D Divertor in the Transition to Detachment Using Extreme Ultraviolet Spectroscopy

Experimental observations of extreme ultraviolet resonance emissions in the divertor of DIII-D are used to quantitatively account for radiated power from molecular, atomic and ionized plasma constituents through the transition to detachment. Deuterium emission is found to be the primary emitter near the target scrape-off layer regions while the main impurity in DIII-D, carbon, is found to dominate the X-point region up the divertor legs. In an attached divertor, C emissions peak inboard of the strike point, while with a detached target, their emission region elongates radially. A relative lack of observed Lyman-Werner bands suggests that radiated power from molecules is minimal even with Te,OSP=1-2eV. Species-resolved measurements are necessary to understand a shortfall in radiated power as modeled with 2D fluid codes on multiple tokamaks. The spectrometer fielded for this purpose is a SPRED (Survey, Poor Resolution, Extended Domain) observing the 100-1700Å region. A broad grating provides views of C II, III, and IV resonance emission lines as well as the D Lyman-α line, together accounting for >80% of the power radiated in the divertor. The divertor SPRED (DivSPRED) is mounted with a vertical line of sight into the machine coincident with boundary diagnostics including divertor Thomson scattering. Work supported by the US DOE under DE-AC52-07NA27344, DE-FG02-07ER54917, DE-FC02-04ER54698, DE-AC05-00OR22725, DE-AC02-09CH11466, and DE-AC04-94AL85000, and LLNL LDRD project 17-ERD-020.

Speaker: Dr Adam McLean (Lawrence Livermore National Laboratory)

mclean_iaea2018_summary.pdf

516 Rotation Profile Hollowing in DIII-D Low-Torque Electron-Heated H-mode Plasmas

Recent experiments in the DIII-D tokamak obtained low torque MHD-free H-mode discharges approaching ITER baseline conditions revealing mid-radius rotation profile hollowing associated with turbulent transport. This indicates that hollowing of toroidal rotation profiles that occurs prior to onset of large-scale MHD observed in low torque ITER Baseline conditions is not due to pre-existing MHD mode drag, but a natural consequence of the turbulent momentum flux. Low torque (T~0.6Nm) plasmas in the ITER similar shape with q95~4.3, βN~1.2-1.6 and electron cyclotron heating (ECH) power between 0-3.4 MW deposited between ρ=0.3-0.7 are studied for ion and electron heating effects on momentum transport. Turbulent density fluctuations are measured with Doppler backscattering (DBS) for intermediate-k (kθρs 1-5) and beam emission spectroscopy (BES) for low-k (kθρs < 1). Contrasting times in a discharge with a core tearing mode with a later phase after the tearing mode has disappeared, the role of the mode on rotation profile hollowing can be determined. In the presence of the mode, the rotation profile is flat or moderately peaked. However, after the tearing mode disappears, the profile takes on a non-monotonic, localized “well” or hollowness, with a positive local rotation gradient. We interpret this phenomenon as the tearing mode reducing the turbulent transport near the island by shunting the thermal flux, flattening the profiles and reducing the turbulent residual stress. When the tearing mode disappears, turbulence increases and the turbulent residual stress is able to drive the non-monotonic rotation profile. Fluctuations in the region of the non-monotonic rotation reveal both low-k ion temperature gradient (ITG) as well as intermediate-k trapped electron mode (TEM) scale fluctuations. The theoretical impact of the linearly unstable modes and turbulent transport mechanisms on the rotation hollowing is still being investigated. This work was supported in part by the US Department of Energy under DE-FC02- 04ER54698, DE-SC0014264 and DE-AC02-09CH11466, and carried out within the framework of the EUROfusion Consortium and has received funding from the Euratom research and training programme 2014-2018 under Grant Agreement No. 633053

Speaker: Dr B.A. Grierson (Princeton Plasma Physics Laboratory)

Grierson IAEA FEC 2018 Nutshell Single.pptx

517 Rotation-induced electrostatic-potentials and density asymmetries in NSTX

The computation of rotation-induced electrostatic potentials is currently being used to study the associated two-dimensional distribution of impurity density asymmetries in NSTX and NSTX-U plasmas. The main effect of toroidal rotation on heavy impurities is their radial displacement to the outer plasma, which result in a non-uniform distribution around a magnetic flux-surface. Due to the different effect of centrifugal forces on electrons, main ions and low- to high-Z impurity density, an electrostatic potential is generated to satisfy quasi-neutrality. This calculation relies on flux-surface quantities like electron and ion temperature $(T_{e,i})$ and rotation frequency $(\omega_{\phi})$ and finds the 2D electron, deuterium and carbon density profiles self-consistently assuming the presence of a poloidal variation due to centrifugal forces. The few assumptions considered include a zero electron mass, a deuterium plasma, a trace impurity with charge “Z” given by coronal equilibrium and equilibrated ion temperatures (e.g. $T_D=T_C=T_Z$). The iterative solution for the electrostatic potential from the measured carbon density and central toroidal rotation using NSTX data are routinely obtained and compared with the values derived using the ideal formalism which assumes that the main low-Z intrinsic impurity (e.g. Carbon) is in the trace limit $\alpha_{C}\equiv36n_{C}/n_{e}\ll1$; realistic values of the low-Z impurity strength factor can exceed one. While the carbon asymmetry is nearly three times stronger than the ideal description, the depth of the potential well in the high field side can reach -110 to -280 V for core rotation between 180 – 360 km/s. This computation is being used to increase our understanding of medium- and high-Z asymmetries and the reduction of Z-peaking, to examine the effect of electrostatic potentials possibly changing the heat and particle transport, the reduction of the underlying turbulence due to $E\times B$, radiation asymmetries before tearing mode onsets, as well as to aid the design of new diagnostics for NSTX-U (e.g. ME-SXR, XICS, Bolometers, etc). The presence of O, Ne, Ar, Fe, Mo and W are considered at the trace limit with very small changes to quasineutrality and $Z_{eff}$. This work is supported by the U.S. Department of Energy, Office of Fusion Energy Sciences under contract number DE-AC02-09CH11466.

Speaker: Dr Luis F. Delgado-Aparicio (Princeton Plasma Physics Laboratory)

518 Scalings of Ion Temperature Gradient Turbulence and Transport

An analytic saturation theory for toroidal ion temperature gradient turbulence is derived from a well-known fluid model, providing the saturated levels of the unstable fluctuation, a nearly conjugate stable mode, and the zonal flow, along with their dependencies on the model parameters. The theory utilizes the eigenmode decomposition of the dynamical equations, applies statistical closure, and introduces an ordering expansion to isolate and analyze zonal-flow-catalyzed energy transfer. This is the dominant energy transfer channel, carrying energy from the instability, through a zonal flow to the dissipated stable mode via nearly resonant wavenumber triads. Solution of closed energy balance equations for the critical sources and sinks yields a turbulence level that is proportional to the ratio of the zonal flow damping rate and the inverse of the triplet correlation time of the zonal-flow catalyzed wavenumber triplet interaction. The zonal flow energy is proportional to the ratio of the growth rate and the inverse correlation time. The analytic solutions for saturation level and scalings are applied to the ion heat flux, showing that it has a factor given by the standard prediction of quasilinear theory, and correction factors that include the inverse of the triplet correlation time a reduction due to the stable mode. This form, which holds for both zero and finite plasma beta, is used to model the beta scan of modified cyclone-base-case gyrokinetic ITG turbulence in simulations with GENE. Standard quasilinear theory does not fall off sufficiently fast with beta to match the nonlinear flux. Inclusion of the correlation time factor, which increases strongly with beta at low perpendicular wavenumber, produces a modified quasilinear prediction that agrees well with the nonlinear flux.

Speaker: Prof. Paul Terry (University of Wisconsin-Madison)

519 Self-driven Current Generation in Turbulent Fusion Plasmas

Plasma self-generated current (e.g., the bootstrap current) contributes to the generation of poloidal magnetic field for plasma confinement in tokamaks, and also strongly affects key MHD instabilities. It is found that plasma turbulence may strongly influence self-driven current generation. This could have a radical impact on various aspects of tokamak physics. Our simulation study employs a global gyrokinetic model coupling self-consistent neoclassical and turbulent dynamics with focus on mean electron current. Distinct phases in electron current generation are illustrated in our initial value simulation. In the early phase before turbulence develops, the electron bootstrap current is established in a time scale of a few electron collision times, which closely agrees with the neoclassical prediction. The second phase follows when turbulence begins to saturate, during which turbulent fluctuations are found to strongly affect electron current. The profile structure, amplitude and phase space structures of electron current density are all significantly modified relative to the neoclassical bootstrap current by the presence of turbulence. Both electron parallel acceleration and parallel residual stress drive due to turbulence are shown to play important roles in turbulence-induced current generation. The former can change the total plasma self-generated current though turbulence-induced momentum exchange between electrons and ions, and the latter merely modifies the current density profile while keeping the total current unchanged. The current density profile is modified in a way that correlates with the fluctuation intensity gradient through its effect on $k_{\parallel}$-symmetry breaking in fluctuation spectrum. Turbulence is shown to reduce (enhance) plasma self-generated current in low (high) collisionality regime, and the reduction of total electron current relative to the neoclassical bootstrap current increases as collisionality decreases. The implication of this result to the fully non-inductive current operation in steady state burning plasma regime could be important and should be investigated. Finally, a significant non-inductive current is observed in flat pressure region, which is a nonlocal effect and results from turbulence-spreading-induced current diffusion. Work supported by U.S. DOE Contract DE-AC02-09-CH11466.

Speaker: Dr Weixing Wang Wang (Princeton University Plasma Physics Laboratory)

520 Simulation study of electrostatic potential generated by NBI and its effect on the neoclassical transport of carbon impurity ions in LHD

Electrostatic potential $\Phi_{\rm NBI}$ generated by the neutral-beam-injection (NBI) to the plasma, and its effect on the neoclassical transport of carbon impurity ions in the Large Helical Device (LHD) are investigated for the first time by means of the global drift-kinetic simulations. The ripple-trapped beam ions of the perpendicular NBI (40keV) have been found to generate $\Phi_{\rm NBI}$ in the order of 0.01-0.02$T_{\rm e}$ when $n_{\rm e}=3\times 10^{19} {\rm m}^{-3}$, $T_{\rm e}=T_{\rm i}=3$keV, and the injection power is 5MW. The global neoclassical transport simulations taking into account $\Phi_{\rm NBI}$ have shown that the diffusion coefficient of C${}^{6+}$ impurity ions decreased by 14% and the radially inward convection velocity decreased by 22% in the presence of $\Phi_{\rm NBI}$ of the 5MW injection. These new findings suggest that $\Phi_{\rm NBI}$ may have a non-negligible impact on the neoclassical impurity transport in LHD, especially in the impurity-hole plasma with high-power NBI heating.

Speaker: Prof. Hiroyuki Yamaguchi (National Institute for Fusion Science, National Institutes of Natural Science)

IAEA2018_1page-slide_Yamaguchi.pdf

521 Study of evolution of trapped particle undamped coherent structures: An important agent in intermittent plasma turbulence and anomalous transport

The physics of particle and energy transport in collision-less plasmas presents substantial challenge because of largely linear threshold based plasma turbulence are replaced by their nonlinear counterparts capable of operating at smaller amplitudes. An outstanding property for collision-less plasmas is the essential nonlinear character of coherent structures supported by them at small amplitude. A supplementary mode spectrum of stable coherent structure plays an important role in intermittent plasma turbulence and anomalous transport. In the present work, these additional undamped structures are considered, in a 1D, collision-less plasma as a paradigm of intermittent plasma turbulence and anomalous transport and are investigated based on the result of a kinetic simulation of the plasma. The computational analysis explores initial phase-space perturbation in a current-driven plasma within the linear threshold limit for accessing the regime uncovered under the linear approximation. These coherent structures are described by a continuum of electron and ion hole modes governed by a multi-parametric nonlinear dispersion relation (NDR)[1]. On the basis of both the simulation results and the three level comprehensive description, namely fluid, linear Vlasov and nonlinear Vlasov descriptions, the importance of trapped particle nonlinearity and the invalidity of the linear threshold limit for v_{phase}<< v_{th} are presented. The formulation describing the evolution merges the discrete and continuum limits by resolving the inevitable resonant region and shows that coherent electrostatic equilibria are generally controlled by kinetic particle trapping and are hence fundamentally nonlinear. The analytical results are characterized with respect to the evolution observed in the kinetic simulations and quantitative analysis of the associated coherent structure parameters. [1] H. Schamel, D. Mandal, D. Sharma, Phys. Plasmas, 24, 032109 (2017)

Speaker: Mr Debraj Mandal (Institute for Plasma Research)

FEC_18_conf_paper.pdf

522 The Effect of RMP ELM Control for ITER on Pedestal Pressure Compared to EPED No-RMP Predictions

The ITER baseline and alternate scenarios use 3D Resonant Magnetic Perturbation (RMP) fields to control ELMs, and therefore ITER operating scenario (IOS) analysis needs to include the effect of the 3D fields on the pedestal pressure and overall device performance. In IOS analysis, the pedestal pressure, for a given pedestal density, will be predicted with the EPED code. Neural net techniques (NN-EPED) have already been applied to databases of EPED computational results to decrease the time needed to make a pedestal pressure prediction by about a factor of 10^9. A new neural network (NN-RMP), trained on measured pedestal data from RMP ELM control discharges in DIII-D, determines the effect of RMP application on the pedestal pressure compared to EPED pressure predictions. Consistent with Random Forest statistical analysis of the parameters most important to the effect of RMP on pedestal pressure, the NN-RMP shows a strong dependence of the reduction in achieved pressure vs. EPED predictions on applied RMP amplitude, but also on pedestal toroidal rotation and either toroidal field (BT) or plasma current (Ip). The dependence on pedestal rotation is indicative of the dependence on RMP penetration and bifurcation physics. The dependence on either BT or Ip, with other geometry parameters fixed, is indicative of the sensitivity to edge safety factor (q95) seen in many DIII-D RMP ELM control discharges. The NN-RMP predicted pedestal height is up to 20-25% lower than EPED predictions for the cases with strongest ELM mitigation or ELM suppression. For ITER operating scenario analysis, this work provides a tool to adjust the EPED-predicted ITER pedestal pressure for the use of RMP fields to mitigate or suppress ELMs. This work was supported in part by the US Department of Energy under DE-FC02-04ER54698, LLNL DE-AC52-07NA27344 and the Science Undergraduate Laboratory Internship (SULI) program and under DE-FC02-04ER549698.

Speaker: Dr Max Fenstermacher (Lawrence Livermore National Lab)

MEF_IAEA18_summaryslide.pdf

523 The universality of inter-ELM pedestal fluctuations in AUG and DIII-D - Impacting the edge profile structure by clamping of the gradients

For wide ranges of operational parameters and in machines with different wall materials, the inter-ELM pedestal profile evolution was robustly linked to characteristic fluctuations, indicating that universal instabilities dominate the pedestal structure and its dynamics in between edge localized modes (ELMs). The presented results substantially advance the comprehension of the underlying instabilities that determine the pedestal structure because ion and electron density as well as temperature gradients were found to become clamped in different phases of the ELM cycle. The general behavior of the inter-ELM fluctuations supports that similar mechanisms determine the pedestal of future fusion devices, and stresses the necessity that predictive models need to incorporate a robust mechanism, which describes the clamping of individual profile gradients across wide ranges of pedestal parameters. The inter-ELM fluctuations exhibit a similar sequence of their onsets in ASDEX Upgrade and DIII-D. This gives strong evidence that their origin is the same, although both machines usually operate in different parameter regimes. Generally, low fluctuation amplitudes are found during the initial recovery of the maximum electron density gradient. After this phase, maximum electron density gradient saturates. The electron temperature pedestal evolves further and the saturation of maximum electron temperature gradient correlates with the onset of high frequency fluctuations. Fast vertical plasma oscillations were utilized as a tool to probe the pedestal fluctuations as well as the pedestal stability. Such oscillations perturb the edge current. To make them an effective ELM pacing method, the pedestal must evolve close to its gradient saturation. This state of saturated gradients is stable, but marginal to the stability limit. If a perturbation, e.g. of the edge current, is applied, it is highly probable that an ELM crash is triggered. This work has been carried out within the framework of the EUROfusion Consortium and has received funding from the Euratom research and training programme 2014-2018 under grant agreement No 633053. The views and opinions expressed herein do not necessarily reflect those of the European Commission. This work was supported by the US Department of Energy under DE-FC02-04ER54698, DE-SC0015878 and DE-SC0015480.

Speaker: Dr Florian M. Laggner (Princeton University)

Laggner_IAEA2018_SummarySlide.pptx

524 Theory of turbulence driven intrinsic rotation and current

We present new results in the theory of turbulence driven intrinsic rotation and current. Both the intrinsic rotation and the intrinsic current driven by micro-turbulence are important for ITER. The former is critical for ITER due to its important role in suppressing MHD instabilities, since neutral beam injection may not provide enough external rotation drive in ITER. The latter is important because the non-inductive current drive is essential for steady state operation of tokamak reactor. This paper presents a novel mechanism for the origin of intrinsic rotation, which is referred as turbulent acceleration [1]. We emphasize that the turbulent acceleration does not contradict momentum conservation law [2]. The possible relevance of the turbulent acceleration to some experimental observations is also discussed [3, 4]. Inspired by the investigation of intrinsic rotation (which is related to ion momentum) driven by turbulence, we also present the intrinsic current (which is related to electron momentum) driven by turbulence [5]. [1] Lu Wang* and P. H. Diamond, Phys. Rev. Lett. 110, 265006 (2013). [2] Shuitao Peng and Lu Wang*, Phys. Plasmas 24, 012304 (2017). [3] Lu Wang*, Shuitao Peng and P.H. Diamond, Phys. Plasmas 23 042309 (2016). [4] Shuitao Peng, Lu Wang* and Yuan Pan, Nucl. Fusion 57 036003 (2017). [5] Wen He, Lu Wang*, Shuitao Peng, Weixin Guo, and Ge Zhuang, “Intrinsic current drive by electromagnetic electron temperature gradient turbulence in tokamak plasmas”, to be submitted to NF.

Speaker: Prof. Lu Wang (International Joint Research Laboratory of Magnetic Confinement Fusion and Plasma Physics, State Key Laboratory of Advanced Electromagnetic Engineering and Technology, School of Electrical and Electronic Engineering, Huazhong University of Science and Technology)

Summary-IAEA FEC-THP6-4.pptx

525 Total-f gyrokinetic turbulent-neoclassical simulation of global impurity transport and its effect on the main-plasma confinement

First-principles-based multiscale neoclassical-and-turbulent understanding of the impurity transport and its effect on the main plasma confinement is one of the most important subjects in magnetic fusion research. Seeding of impurity particles was found to improve the plasma confinement in the so-called “RI-mode” of operation [Weynants et al., Nucl. Fusion 39 (1999)]. More recently tungsten (W) impurities have been found to degrade the pedestal confinement of JET ILW H-mode plasma while a seeding of nitrogen (N) impurities reduces the degradation [Litaudon et al., 2017 Nucl. Fusion 57 (2017)]. In the present study, the total-f gyrokinetic code XGC1 [Chang et al., Phys. Rev. Lett. 118 (2017) ] is used to understand the impurity transport in the whole-volume plasma and its effect on the main plasma confinement.

Recent total-f simulation by XGC1 [Kim et al., Phys. Plasmas 24 (2017)] showed that carbon (C) impurity can improve the main-ion confinement by reducing the ITG turbulence amplitude. In the presence of C+6 impurities, the self-organized deuteron temperature and its gradient were found to increase by up to $20%$ at all radial positions under the same central heating condition. This confinement enhancement was found to be caused by a stabilization effect due to both the impurity-wave interaction and the enhanced mean ExB shearing rate, rather than by the main-ion dilution effect. Another important finding is that the central peaking of impurity density in the saturated state is not as severe as what has been known from neoclassical theories. The neoclassical impurity inward-pinch is heavily opposed by the outward turbulent transport to yield only a mild impurity-density peaking in the saturated state. In these simulations, gyrokinetic deteron and carbon ions with Z_eff≃1.75 have been utilized with adiabatic electrons.

On-going research on the tungsten-nitrogen impurity transport and its impact on the H-mode pedestal in JET plasmas in realistic divertor geometry will also be presented. Starting with the impact of W-impurity on the neoclassical ExB shearing profile in a JET pedestal. Transport of the W and N particles into the central core will be included in the discussion. For whole-volume simulations, we will use new core-edge coupling technique developed in the High-fidelity Whole-Device-Modeling program of the Exascale Computing Project.

Speaker: Dr Choong-Seock Chang (Princeton Plasma Physics Laboratory and KAIST)

Dominski.J-TH-C-slide.pptx

526 Towards a predictive modelling capacity for DT plasmas: European Transport Simulator (ETS) verification and validation

The European Transport Simulator (ETS) [1] has been developed under the EUROfusion Integrated Modelling (EU-IM) effort [2] to meet the requirements for scenario development of burning plasmas. The ETS focuses both on interpretive and predictive modelling and is now being deployed for broader exploitation, e.g. on the JET computing infrastructure for close integration and use in support of JET campaigns. Recently, developments have been undertaken to enhance the ETS modelling capabilities for DT plasmas in view of the upcoming experiments. A coherent inclusion of fast particle physics effects as well as a consistent approach for multispecies plasmas have been implemented. Major features are the capability for separate modelling of the different hydrogen isotope channels as well as light and heavy impurities - in all their charge states - and a set of advanced heating and current drive modules, which, for example, allows for ICRH heating effects on majority ions. ETS is also used in modelling runaway electron scenarios and NTMs. Here we describe the extensions to the ETS workflow undertaken to enhance the modelling capabilities for DT plasmas and discuss a detailed verification and validation activity. The ETS also sports a set of transport models (TGLF, Qualikiz, EDWM) capable of resolving and providing transport for hydrogenic isotopes as well as light and heavy impurities. Results with these models as well as a discussion on approaches attempting to resolve inherent mass scaling issues will be shown. [1] D. Kalupin et al, Nucl. Fusion 53, 123007 (2013) [2] G.L. Falchetto, et al., Nucl. Fusion, 54, 043018 (2014)

Speaker: Dr Par Strand (Space, Earth and Environment, Chalmers University of Technology, SE-41296, Göteborg. Sweden)

IAEA_Summary_slide_Thp6-14_Strand_v2.pdf

527 Transport of collisional impurities with flux-surface density variation in stellarator plasmas

Highly charged impurities both dilute plasmas and lead to radiation losses, and thus cannot be allowed to accumulate in the core of a magnetic confinement fusion reactor. For stellarators, the outlook has been particularly pessimistic, as early theories predicted that impurities would unavoidably be transported inwards in the core. However, recent theoretical work has shown that strong temperature gradients can transport impurities outward, in the reactor-relevant scenario of a weakly collisional bulk ion species and a collisional impurity species. In this work, we extend these results to allow for variations of the impurity density on the flux surface in response to an externally applied electrostatic potential, due to – for example – the presence of anisotropic fast particles. Specifically, we consider the radial transport of a collisional but trace ($Z^2 n_z \ll n_i$) impurity species which varies in response to $\Phi$. We calculate the neoclassical transport of the impurities, and find that localized impurity densities can have a large effect on the radial flux -- even producing sign change -- compared to the homogeneous $n_z$ case. Tentative results show that this effect may be highly relevant for understanding the lack of impurities in "impurity hole" shots in LHD, but less relevant for carbon transport in W7-X due to the smaller $\Phi$-variations in the latter. However, the effect becomes more important at higher impurity-charge, and can thus be expected to be relevant for tungsten transport also in W7-X.

Speaker: Mr Stefan Buller (Chalmers University of Technology)

bstefan_IAEA2018_poster.pdf

528 Transport simulation of EAST long pulse discharge and high betaN discharge with integrated modelling

In the past two years, two major scenarios were developed on the EAST tokamak, the long pulse steady state scenario and the high $\beta_N$ scenario. For the steady state scenario, 100 s long pulse discharge was achieved with only radio frequency heating and current drive (CD) and it has improved confinement with H98~1.1. For the high $\beta_N$ scenario, the $\beta_N$ ~2.0 was sustained for ~2 s, with an internal transport barrier (ITB) in all channels. Under OMFIT framework, a workflow was developed to simulate the two scenarios on EAST. The workflow integrated the equilibrium code EFIT, transport code TGYRO for energy transport, transport code ONETWO for current evolution and radiation, heating and CD code GENARY/TORAY/NUBEAM for driven current and energy sources. For long pulse discharge, the integrated modelling well reproduced the experimental electron and ion temperature profiles and current (or q) profiles. This validated our integrated modelling workflow and validated the TGLF transport model for the scenario possessing dominant electron heating and low toque. The modelling also gives the physical picture of the improved confinement induced by the on-axis ECH: the on-axis ECH increased the central electron temperature, make the LHCD power deposit to inner region and make the current profile more peaked, which suppress the high-k micro-instabilities at the core region and improve the confinement. The integrated modelling workflow also was used for the high $\beta_N$ discharge of EAST. However, it could not reproduce the experimental temperature profiles. The reason is that the fishbone instability appears in the discharge, which could redistribute the fast ion and affect the energy transport. A heuristic model was developed to include the effects of fishbone instability, then the temperature profiles simulated by our integrated modelling qualitatively agreed with the experiments.

Speaker: Dr Guoqiang Li (Institute of Plasma Physica, CAS)

1p summary.pptx

529 Weak turbulence transport with background flows using mapping techniques including finite Larmor radius effects

Electrostatic drift waves produce transport by the E X B motion of a particle guiding center (GC) which can be studied from a Hamiltonian description where the electrostatic potential plays the role of the Hamiltonian. Here, the fluctuating potential is considered to be an infinite spectrum of waves, characteristic of weak turbulence, in two-dimensions. This is studied using a map that presents regular a nd chaotic regions. With an ensemble of particles transport is studied statistically. Finite Larmor radius (FLR) of the particles is include by taking the gyroaverage over one orbit. The main effect is to reduce the wave amplitude that produces a given level of chaos, so fast particles are better confined. The transport is diffusive and the particle distribution functions (PDF) are Gaussian. Then a thermal distribution of Larmor radii was taken which produces the PDFs to become non-Gaussian with long tails while the transport stays diffusive. This behavior is explained theoretically and it is shown that it agrees with the numerical results. When a sheared flow is included the transport is described by a symplectic mapping when the shear is monotonic. The result is that the poloidal flow has the effect of increasing the poloidal transport so that the variance of the distribution has cubic dependence with time. This super-ballistic scaling means that the particles have an acceleration when the flow is present. This is due to a grow of the particle step size as time increases related to the diffusive spreading in the radial direction. Thus, the waves acting in two dimensions promote particles to take energy from the perpendicular direction of the flow to the parallel direction. The PDF does not deviate much from a Gaussian. Inclusion of FLR effects keeps these results. When there is a thermal distribution of Larmor radii the PDF is no longer Gaussian as in the case without flow. The radial transport is still diffusive but it is enhanced over the values with no flow. The radial transport is still diffusive but it is enhanced over the values with no flow. The self-similarity function is Gaussian for small thermal gyroradius but a long-tailed exponential distribution for large gyroradius. Then, the flow is taken to have non-monotonic radial shear. The map is double-valued and non-twist. The associated transport barriers are studied as well as the FLR effects.

Speaker: Dr Julio Martinell (Nuclear Sciences Institute, National Autonomous University of Mexico)

16:10 Coffee Break

FIP/3 DEMO & Advanced Technology

530 Overview of the DEMO Design-Staged Approach in Europe

This paper describes the status of the DEMO design activities performed in Europe and discusses the impact of some of the key requirements (such as electrical output, tritium self-sufficiency), the main constraints (e.g., those deriving from the tokamak-side and the Balance-of-Plant (BoP) / Power Conversion System (PCS)) on the systems design solutions and on the overall plant architecture. The paper focuses on the main DEMO technical / design integration issues, e.g., those where there are either gaps with ITER because of the inherent differences in the design approach and / or technologies adopted (e.g., protection of the first wall, possibly divertor configuration, tritium-fuel cycle, etc.), or because of the difference of plant requirements (e.g., tritium-breeding and extraction, thermal power extraction and conversion to electricity, remote maintenance schemes for high plant availability). The design of the breeding blanket and the selection of its coolant are examples that bear a strong impact on integration, maintenance, and safety because of the interfaces with all key nuclear systems (e.g., the BoP and PCS, tritium recovery and purification systems, etc.). Work continues to be focused on the design of a pulsed baseline DEMO plant concept that integrates all the major DEMO sub-systems to understand integration risks and resolve design interface issues. Considerations are also given to a design based on latter-stage ITER scenario and able to operate in a short pulse mode (e.g., 1 hr) for nominal extrapolated performance (H98=1.0) and capable of moving to steady-state operation while maintaining the same fusion power and net electrical production in the case of a better confinement being feasible. However, this option requires a much higher confidence in physics extrapolation and highly reliable and efficient current-drive and control systems, which need to be deployed by day-1 and still need to be developed. The definition and analysis of the physics scenarios for the concept design and identification of the physics basis development needs are described elsewhere. Incorporating lessons learned from the ITER design and construction, building of relationships with industry and embedding industry experience in the design are needed to ensure early attention is given to industrial feasibility, costs, nuclear safety and licensing aspects.

Speaker: Dr Gianfranco Federici (Eurofusion Consortium)

Overview_DEMO Federici_FEC_2018_India_fin.pdf

Overview_DEMO Federici_FEC_2018_India_fin.pptx

Summary_Slide_DEMO Federici_FEC_2018_India.pdf

531 Development of physics and engineering designs for Japan's DEMO concept

Recent design progress of Japan's DEMO is presented regarding the engineering and physics conceptual design of a steady-state DEMO with a major radius of 8 m class and fusion power of 1.5 GW level. The design concept of divertor is similar to that of ITER. By considering the neutron irradiation environment, a Cu-alloy cooling pipe is used only in the large heat flux region, while a RAFM steel cooling pipe in the small heat flux region. The divertor cassette design is developed for reducing the fast neutron flux to protect the vacuum vessel and for replacement of the power exhaust units with the tungsten mono-block and Cu-alloy pipes. The breeding blanket concept based on JA ITER-TBM is developed to increase the pressure-tightness of the modules by considering safety assessment of in-box LOCA. Regarding the TF coil design, assessment of the error field indicates that the tolerance can be mitigated by ~2.5 times as large as ITER's with correction coil current of several 100 kAT/coil. The concept of remote maintenance for the blanket segments is developed such as the stable transfer mechanism in the vertical, radial and toroidal directions. The rad-wastes generated by the maintenance can be desposed of in shallow land burial after 10-year storage. The concept of primary cooling water system is developed for effective use of thermal power removed from not only blanket but also divertor, where thermal power removed from the divertor is used for preheating the blanket coolant, and a bypass line is installed to control the coolant flow for reducing the pressure drop. As for the physics design, one of the major issues is the compatibility between the operational density and the divertor detachment. The evaluation of the lower boundary of operational density to be compatible with the capability of the heat removal and suppression of tungsten erosion indicates that the partial detachment with the acceptable peak heat load is obtained at the operational density, and that the net erosion is almost suppressed. Furthermore, plasma operation scenario is developed and indicates the importance of off-axis ECCD for controlling the internal transport barriers. It is concluded that the DEMO concept considerably mitigates power handling issues compared with the previous compact DEMO, SlimCS, although some challenging design issues remain to be resolved.

Speaker: Dr Yoshiteru Sakamoto (National Institutes for Quantum and Radiological Science and Technology)

201810_IAEA2018_Sakamoto_v3.1.pdf

Summary slide_FIP3-2.pptx

532 Novel Radio Frequency Current Drive Systems for Fusion Plasma Sustainment on DIII-D

The DIII-D National Fusion Facility is advancing the science and technology of steady-state fusion plasma sustainment through the implementation of two first-of-a-kind radio frequency current drive systems: the "helicon" or fast wave in the lower hybrid range of frequencies (LHRF), and high field side (HFS) launch of the lower hybrid slow wave. Using existing DIII-D discharges, we have identified high performance scenarios that are predicted to have excellent wave penetration, strong single pass absorption and high current drive efficiency. Simulations predict this will raise ideal $\beta_N$ limits in DIII-D and permit access to higher density advanced tokamak regimes. The higher B-field on the HFS improves wave accessibility and allows for use of lower n||, resulting in higher current drive efficiency for LHRF slow waves and damping at r/a~0.6-0.8 on the first pass. The 476 MHz helicon has better accessibility at lower B-field and higher density than the 4.6 GHz slow wave due to the lower frequency that can be used for the fast wave. Calculations show that HFS launch of slow waves in the LHRF can lead to a physics current drive efficiency of 0.17x1020 A·W-1m-2 at r/a~0.6-0.8 in DIII-D and 0.4x1020 in a high B-field reactor. HFS LHRF represents an integrated solution that both improves core wave physics and mitigates PMI/coupling issues. An innovative, compact HFS LHRF antenna design has been developed combining a slotted waveguide poloidal splitter (used on C-Mod) and multi-junction toroidal splitter (used on Tore Supra, EAST). Models show good coupling properties for predicted edge density profiles. Current drive by helicons is predicted to be significantly more efficient than either off-axis neutral beam current drive or conventional ECCD in high-density, high electron-beta regimes. A 12-module helicon antenna was developed and tested in DIII-D and demonstrated sufficient coupling at <0.4 kW. A ~1 MW proof-of-principle experiment using helicon waves at 476 MHz launched with a novel 'comb-line' traveling wave antenna with 30 elements will be performed on DIII-D starting in 2019. Work supported by the U.S. Department of Energy, Office of Science, Office of Fusion Energy Sciences, using User Facility DIII-D, under Award Number DE-FC02-04ER54698 and by US DoE Contract No. DE-FC02-01ER54648 under Scientific Discovery through Advanced Computing.

Speaker: Dr Gregory Wallace (MIT Plasma Science and Fusion Center)

wallace_IAEA_v5_32x9.pdf

533 Impact of High Field & High Confinement on L-mode-Edge Negative Triangularity Tokamak (NTT) Reactor

“NTT” is a unique reactor concept based on “power-handling-first“ philosophy by locating long-leg (~2.7m) divertor at outboard side with negative triangularity δ<0 and making flux tube expansion to maximize heat exhaust surfaces (grazing angle ~2°).
Our previous design (Ip=21MA, A=Rp/ap=3, Rp=9m, HH=1.12, Bt=5.86T) uses standard magnet design based on the wedge support and maximum field is limited to 13.6T due to stress limit 800MPa and large reactor size. It allows adoption of currently available Nb3Sn superconductor at 4.5K as well as Bi2122/Pb high Tc superconductor at 20K. NTT configuration has technical merits of having space in the inboard except narrowest point to place the blanket piping and auxiliary systems such as pellet injector line and ECH waveguides. Outward placing of the divertor is favorable for pumping conductance.
Parameter studies on impact of high Bt and HH for A=3, 3.5 are shown where HHIpA=69.3MA, n/nGW=0.85 and qcy=3.5 are fixed. The reduction of major radius to Rp=7m is possible with improved confinement (HH=1.5) while Bmax is nearly constant. In this case, fusion power is reduced to Pf=2GW and the neutron wall load stays almost constant qn~1.4-1.5MW/m2 while the normalized beta βN becomes higher βN=2.9. For fixed HH=1.2, higher Bmax=16T enables to reduce major radius to Rp=7m. In this case, fusion power Pf and neutron wall load qn increases while βN stays almost constant. For A=3.5, we observe similar trend. The plasma volume is smaller (Vp~1000m3) compared with A=3 case (Vp~1500m3). But requirement for Bmax for fixed HH=1.2 becomes rather high Bmax=19.5T. With improved confinement (HH=1.5), reduction of major radius to Rp=7m is possible leading to Ip=13.3MA, Bt=7.53T, n=0.9 x 1020 m-3, Pf=1.9GW, Bmax=15.5T, PCD=115MW (\eta CD=0.5 x 1020 A/m2W is assumed). We made configuration design for this case and the equilibrium calculation. Extended wedge support allows σmax within 800MPa at 4.5K. It is concluded that both high magnetic field and high confinement are important for the realization of reasonably compact NTT fusion reactor as future R&D.

Speaker: Dr Mitsuru Kikuchi (QST)

FEC2018(Kikuchi)final.pptx

One Page summary.pptx

534 Amelioration of plasma-material interactions and improvement of plasma performance with a flowing liquid Li limiter and Li conditioning on EAST & Experiments on FTU with a liquid tin limiter

A. Wall conditioning and ELM control has played a crucial role in enabling access to record long H-mode pulses in EAST. Here we present new results where 1) a 2nd generation (2G) flowing liquid lithium (Li) limiter was inserted into the EAST midplane and used to mitigate plasma-materials interactions (PMI); 2) Li powder was injected to eliminate ELMs in upper-single null (USN) configuration that used the ITER-like tungsten monoblock divertor; and 3) Li granule injection was used for ELM triggering studies. A 2G flowing liquid Li limiter was inserted into EAST and was found to be compatible with H-modes, even when placed within 1cm of the separatrix in RF heated discharges. Both the 2G and 1st generation (1G) limiters use a Cu plate for the heat sink, with a thin stainless steel (SS) coating for Li compatibility. The 2G limiter had several design improvements over the 1G limiter, including a thicker SS protective layer, two jxB pumps instead of one, an improved Li distributor manufacturing process, and surface texturing to improve wetting of the SS face. The fractional surface area that was wetted by the Li was > 80% in the 2G limiter, vs. ~30% in the 1G limiter. The heat flux exhausted by the 2G limiter was up to 4 MW/m2. In otherwise similar conditions, there was a shot-by-shot progressive reduction in Dα emission with 2G limiter insertion, culminating in short-lived ELM-free phases for the first time in EAST, with increasing τE and transient HH98y2 < 2. A 3G limiter has being fabricated out of Mo for upcoming tests. Li powder was injected into USN H-modes using ITER-like tungsten monoblock divertor. At constant Li injection rates, the ELM elimination became progressively easier, suggesting a cumulative wall conditioning effect, as also observed with the 2G flowing liquid lithium limiter. Normalized energy confinement HH98y2 was maintained at about 1.2, well above the previous ELM elimination with Li injection on the lower carbon divertor with HH98y2 ~ 0.75. Finally ELM triggering studies with a four-chamber Li granule injector showed a clear size threshold for ELM triggering probability, as qualitatively predicted by theory. The observed threshold was similar to DIII-D experiments. ELM pacing was also observed, but the paced ELM frequency was below the 200 Hz natural ELM frequency in these discharges, preventing ELM heat flux mitigation conclusions. B. In this paper we report experimental results obtained, for the first time in the world, in a tokamak with a liquid tin limiter (TLL). The FTU TLL was realized by using a molybdenum tube covered with Capillary Porous System (CPS) made by stripes of tungsten felt filled with tin. The TLL can be cooled by flowing air and atomized water inside a copper pipe inserted in the molybdenum tube. To test TLL, a standard FTU discharge was used with a toroidal field B_t = 5.3 T, a plasma current I_p = 0.5 MA and an electron density n_e ≤ 1.0 10^20/m^3. The thermal load on the limiter was progressively varied moving up the limiter shot by shot in the scrape-off-layer (SOL), until almost reaching the last closed magnetic surface (LCMS). The most significant results without active cooling, were obtained by increasing the heat load on the TLL by changing the average electron density from 0.6 to 1.0 10^20/m^3. The thermal load onto the TLL by Langmuir probes increased proportionally with the electron density reaching a value greater than q_LP = 15MW/m^2 for almost 1s for TLL position close to the LCMS. By looking at the temporal evolution of the IR maximum surface temperature and of the measured Sn XXI line emission monitored by the UV spectroscopy, it was deduced that tin evaporation becomes the dominant tin production mechanism when the maximum surface temperature (T_s,max) of the limiter exceeds 1300 °C up to the upper value of 1700 °C reached at the end of the pulse. A maximum heat flux of q_max=18 MW/m^2 resulted in this case by the application of the 3D finite-element code ANSYS to the real design of the limiter and of CPS. A concentration of tin of about 5.0e-04 of the electron density was deduced from the Z_eff value. By applying the JETTO code, no significant difference was found in the confinement time with respect to the case of absence of tin limiter and without degradation of the plasma performance. No droplets into plasma and no damages were observed on the TLL after the plasma exposition.

Speaker: Dr Rajesh Maingi (Princeton Plasma Physics Laboratory)

Maingi_IAEA2018_final2_FIP:3-5a.pdf

Maingi_IAEA2018_oral_v6_fixwide2_manyslides.pdf

535 Experiments on FTU with a liquid tin limiter

In this paper we report experimental results obtained, for the first time in the world, in a tokamak with a liquid tin limiter (TLL). The FTU TLL was realized by using a molybdenum tube covered with Capillary Porous System (CPS) made by stripes of tungsten felt filled with tin. The TLL can be cooled by flowing air and atomized water inside a copper pipe inserted in the molybdenum tube. To test TLL, a standard FTU discharge was used with a toroidal field B_t = 5.3 T, a plasma current I_p = 0.5 MA and an electron density n_e ≤ 1.0 10^20/m^3. The thermal load on the limiter was progressively varied moving up the limiter shot by shot in the scrape-off-layer (SOL), until almost reaching the last closed magnetic surface (LCMS). The most significant results without active cooling, were obtained by increasing the heat load on the TLL by changing the average electron density from 0.6 to 1.0 10^20/m^3. The thermal load onto the TLL by Langmuir probes increased proportionally with the electron density reaching a value greater than q_LP = 15MW/m^2 for almost 1s for TLL position close to the LCMS. By looking at the temporal evolution of the IR maximum surface temperature and of the measured Sn XXI line emission monitored by the UV spectroscopy, it was deduced that tin evaporation becomes the dominant tin production mechanism when the maximum surface temperature (T_s,max) of the limiter exceeds 1300 °C up to the upper value of 1700 °C reached at the end of the pulse. A maximum heat flux of q_max=18 MW/m^2 resulted in this case by the application of the 3D finite-element code ANSYS to the real design of the limiter and of CPS. A concentration of tin of about 5.0e-04 of the electron density was deduced from the Z_eff value. By applying the JETTO code, no significant difference was found in the confinement time with respect to the case of absence of tin limiter and without degradation of the plasma performance. No droplets into plasma and no damages were observed on the TLL after the plasma exposition.

Speaker: Dr Rajesh Maingi (Princeton Plasma Physics Laboratory)

IAEA_Mazzitelli_FIP:3-5Rb .pptx

536 Development of a Lithium Vapor Box Divertor for Controlled Plasma Detachment

A lithium vapor-box configuration [1] has been proposed to provide volumetric radiative dissipation in the divertor region of tokamak plasmas. While recent experiments have achieved continuous vapor shielding in close proximity to a lithium coated target in Magnum-PSI [2], this approach seeks to provide controlled detachment far from the divertor target, in a lithium vapor cloud maintained through controlled evaporation and kept away from the main plasma through baffling and recondensation.

We performed edge-plasma simulations with the geometry and parameters of the recent FNSF study [3]. A set of calculations are performed with the 2D UEDGE plasma model and a simple diffusive neutral model [4]. To mimic a crude vapor-box, Li vapor is injected near the divertor plate from the private-flux and outer divertor leg regions and is removed assuming a wall albedo of 0.5 on both PF and outer walls, which allows steady state solutions. For a range of Li vapor input, steady-state, detached-plasma solutions are shown where well over 90% of the exhaust power is radiated by Li, resulting in peak surface heat fluxes ≤ 2 MW/m^2 on the divertor plate, outer wall, and?private-flux wall. While Li ions?dominate in the divertor leg, their density is much less?than the DT density at the midplane. Here the key?issue is possible dilution of the core DT fuel.

We also developed a simulation of the neutral lithium vapor flow in the divertor using the Stochastic PArallel Rarefied-gas Time- accurate Analyzer (SPARTA) Direct Simulation Monte Carlo (DSMC) code [5]. We have simulated the open geometry of the present FNSF design, as well as begun studies using (so far) a single baffle. While the original open geometry allows 75% of the lithium absorption in the plasma to occur in the far SOL, distant from the divertor leg, this is reduced to 5% through the use of a single baffle.

[1] R.J. Goldston, G.W. Hammett, M.A. Jaworski, J. Schwartz, Nucl. Mat. Eng. 12 (2017) 1118
[2] P. Rindt, ISLA Conference, Moscow 2017
[3] C.E. Kessel, J.P. Blanchard, A. Davis et al., Fusion Eng. Design (2017),
http://dx.doi.org/10.1016/j.fusengdes.2017.05.081.?
[4] T.D. Rognlien, M.E. Rensink, and D.P. Stotler, Fusion Eng. Design (2017),
http://dx.doi.org/10.1016/j.fusengdes.2017.07.024
[5] M.A Gallis et al., AIP Conference Proceedings 1628, 27 (2014); doi: 10.1063/1.4902571

Speaker: Robert Goldston (Princeton Plasma Physics Laboratory)

Goldston LVB IAEA.pdf

Friday, 26 October

EX/7-TH/5 Active ELM Control

537 Test of the ITER-like RMP configurations for ELM-crash-suppression on KSTAR

KSTAR has demonstrated a divertor heat flux broadening during edge-localized-mode (ELM)-crash-suppression using ITER-like 3-row resonant magnetic perturbation (RMP) configurations for the first time. Over the last couple of years, we have established a robust methodology to fully suppress ELM-crashes using low-n RMPs. To address the ITER relevant ELM control, a systematic exploration of various RMP configurations at lower q95 plasmas led us to accomplish RMP-driven, ELM suppression down to q95 = 3.3 [1]. As long as the mode-locking at low q95 is avoided and a quick recovery of the wall conditioning (e.g. cryo-pumping or divertor gas-puffing) is secured, the access to the targeted q95 (~ 3) for ITER is foreseen to be feasible in KSTAR. Taking full advantage of 3-row in-vessel control coils (IVCC) in KSTAR, rather than 2-rows in other devices, a series of intentionally misaligned RMP configurations have been investigated for ELM-crash-suppression. The ITER-like 3-row RMPs were found to have broadened the divertor heat flux in the vicinity of outer strike point, while the 2-row has rarely affected the near scrape-off-layer (SOL) heat flux despite a little broadened profile change in the far-SOL area [2]. Since the main focus of divertor heat flux dispersal would be the redistribution of the peaked near-SOL heat flux, such contrasting 3-D heat flux broadening must be similarly attributable to the choice of 3-rows in ITER, instead of 2-rows. Since such broadening characteristics could be completely different in partially detached plasmas in ITER [3], KSTAR has conducted an investigation of whether RMP-driven, ELM-crash-suppression would be compatible with detached plasmas. Although a fully detached plasma under RMP has not been obtained yet, we were able to greatly reduce heat flux at q95=3.8 using n=2 RMPs in high density plasmas [4]. Overall, the new lessons we have learned would be directly relevant to the successful ITER RMP research, while resolving any uncertainty associated with 3-row RMPs that could be further exploited in KSTAR. References: [1] Y. In et al, APS-DPP invited talk titled “Tamed Stability and Transport using Controlled Non-axisymmetric Fields in KSTAR” (2017) [2] A. Loarte, Y. In et al, to be published (2018) [3] R. Pitts, private communications (2018) [4] J.W. Ahn et al, APS-DPP (2017)

Speaker: Prof. Yongkyoon In (Ulsan National Institute of Science and Technology (UNIST))

FEC2018_In_v6.pptx

OnePageSummary_EX7-1_In.pdf

538 Dynamic ELM and divertor control using mixed toroidal harmonic resonant magnetic perturbations in DIII-D and EAST

Mixed toroidal harmonic Resonant Magnetic Perturbations (RMPs) have been used on both EAST and DIII-D to reduce the threshold for Edge Localized Modes (ELMs) suppression and to spread the divertor heat flux. Experiments using mixed toroidal harmonic RMPs have validated predictions that divertor heat and particle flux can be dynamically controlled while maintaining ELM suppression in DIII-D. Theoretical modeling has reproduced the linear and non-linear response observed on magnetic sensors during ELM mitigation and suppression. Mixed n=2 and 3 toroidal harmonic RMP significantly lower the threshold current for ELM suppression compared to the single n=3 RMP. Rotating RMP has been demonstrated recently in EAST as a promising method in controlling the steady state particle and heat flux on the divertor, when the transient power loads induced by ELMs have been eliminated by RMPs. It is observed that the particle flux patterns on the divertor targets change synchronously with rotating RMP fields as predicted by the modeled magnetic footprint patterns by TOP2D. ELM suppression over one full cycle of a rotating n=2 RMP that was mixed with a static n=3 RMP field has been achieved in DIII-D. Strong changes in the three-dimensional heat and particle flux footprint in the divertor were observed during the application of the mixed toroidal harmonic RMPs, which also agrees well with modeling. Plasma response during ELM suppression using mixed toroidal harmonic RMPs shows that small n = 2 field help to penetrate n = 3 mode which eventually leading to ELM suppression. Plasma response measured by magnetic sensors shows linear relation in the mitigation stage in DIII-D, while a non-linear jump of plasma response is observed during the transition from mitigation to suppression of ELM in DIII-D. MHD simulation with the MARS-F code shows good agreement during ELM mitigation in both mode structure and phase, while it has a phase shift to the observed response during ELM suppression in DIII-D, which is similar to that in EAST. These results expand physics understanding and potential effectiveness of the technique for reliably controlling ELMs and divertor power/particle loading distributions in future burning plasma devices such as ITER. Work supported by USDOE under DE-FC02-04ER54698 and NNSF of China under 11475224.

Speaker: Dr Youwen Sun (Institute of Plasma Physics, Chinese Academy of Scienses)

IAEA_2018_Sun.pptx

Summary IAEA_2018_Summary_Sun.pptx

539 Experimental conditions for suppressing Edge Localised Modes by magnetic perturbations in ASDEX Upgrade

Full suppression of Edge Localised Modes (ELMs) by magnetic perturbations (MP) in high-confinement mode (H-mode) plasmas has been obtained in ASDEX Upgrade (AUG) in a shape-match experiment with DIII-D [Nazikian, IAEA FEC 2016]. In contrast to previous scenarios where ELMs were mitigated by MP, full ELM suppression in AUG requires stronger shaping. This finding has been attributed to larger pedestal plasma pressure, which in turn leads to stronger amplification of the external MP by marginally stable, edge localised, kink-peeling modes. Recent experiments in AUG aimed to identify critical parameters for accessing ELM suppression: Safety factor, plasma rotation, plasma edge density and collisionality. Edge safety factor scans in the range of $q_{95} = 3.6-4.2$ showed a window $q_{95} = 3.66-3.91$ for ELM suppression with $n=2$ MP. In the ELM suppression scenario used so far, there is a clear maximum edge density ($3.5 \times 10^{19}$ m$^{-3}$) for ELM suppression, which can also be expressed as a collisionality limit. Our present data set is still too sparse to discriminate between these quantities. In H-modes with ELM mitigation or ELM suppression, the pedestal pressure is typically $32\%$ below that of ELMy H-mode with MP switched off and still somewhat below that of phases with MP-mitigated ELMs. The resonant, field-aligned MP components near the top of the H-mode edge gradient region are believed to be essential for ELM suppression [Wade, Nucl. Fus. 2015] and their strength in turn depends (in two-fluid MHD) on the absence or presence of electron flow across the magnetic field ($v_\mathrm{e,\perp}$) which can induce helical currents that shield the MP. In our experiment we find that the toroidal rotation at the pedestal top, measured by charge exchange recombination spectroscopy on $B^{5+}$ impurities, varies widely, $v_\mathrm{tor} = 0 - 40$~km/s. There is also significant variation of $v_\mathrm{e,\perp}$, despite ELM suppression being maintained. This includes cases with zero-crossing in the pedestal region (weak shielding) and cases where $v_\mathrm{e,\perp}$ (in electron drift direction) in the entire pedestal region is sufficiently strong to shield the resonant plasma response everywhere.

Speaker: Dr Wolfgang Suttrop (Max-Planck-Institut für Plasmaphysik)

wsuttrop_fec2018_slides.pdf

wsuttrop_fec2018_slides_squashed.pdf

wsuttrop_fec2018_SummarySlide.pdf

540 ELM Control Physics with Impurity Seeding and LHCD in the HL-2A Tokamak

ELM control is a key issue in the magnetic fusion reactor. Experiments for controlling ELMs have been performed in the HL-2A tokamak with several tools, including lower hybrid current drive (LHCD), laser blow-off (LBO) seeded impurities (Al, Fe, W) and supersonic molecular beam injected (SMBI) impurities (Ar, Ne). A beneficial effect of the pedestal deposited impurity injected by LBO on ELM mitigation/suppression has been demonstrated in a controlled manner. In addition, the dependence of these effects on impurity species and amount has been systematically investigated. Mixture SMBI with impurity was firstly carried out in HL-2A. Experimental results suggest that there exists an optimal impurity ratio for heat load control in H-mode plasmas, and pedestal dynamics can be actively controlled by exciting pedestal instabilities with impurity seeding. ELM mitigation with LHCD has been also successfully achieved in HL-2A. The divertor peak heat load during an ELM is strongly reduced during the mitigation phase. After the LHCD application, the pedestal velocity shear has undergone a severe decrease, and the radial wavenumber spectrum of the pedestal turbulence is shifted toward the origin. It has been found that the ELM mitigation is not synchronized to LHCD pulse with a significant delay, while it is closely correlated to the enhancement of the pedestal turbulence, indicating that as for impurity injection, the ELM mitigation with LHCD can be directly caused by the enhancement of the pedestal turbulence. In order to understand the mechanism of the turbulence enhancement during ELM mitigation, a theoretical turbulent heat transport model, based on the regulation of the turbulence amplitude by its radial wavenumber spectral shift caused by external velocity shear, has been developed. This external velocity shear can be from SMBI, impurity injection or LHCD. A critical growth rate γ0 for the turbulence regulation has been identified in this theoretical model. It has been found that the turbulence enhancement and ELM mitigation occur when the external velocity shear exceeds a threshold value, which directly depends on γ0. Qualitatively, ELM mitigation with pedestal turbulence enhancement and radial spectral shift due to the pedestal velocity shear reduction can be simulated with this theoretical model.

Speaker: Mr Guoliang Xiao (Southwestern Institute of Physics，China)

EX7-4 ELM Contro Summary slide.pptx

IAEA_ELM Control Physics_XIAOGL.pdf

IAEA_ELM Control Physics_XIAOGL.pptx

541 A nonlinear 2-fluid study of the effect of pellet injection on ELM dynamics

We report on nonlinear simulation studies of the dynamical behavior of ELMs under the influence of repetitive injection of pellets using the nonlinear 2-fluid code CUTIE. ELMs are excited by introducing a particle source in the confinement region and a particle sink in the edge region. High density pellets are injected repeatedly near the edge with different duty cycles, where a duty cycle refers to the ratio of `on’ time and `off’ time of localized density perturbations. A combination of various duty cycles and different densities of the pellets have been used and comparative studies of the time series in edge density and temperature perturbations both in the absence and presence of pellets have been made. We find that the pellets significantly influence both the frequency and amplitude of the ELMs and the results are sensitive to the duty cycle and the density of the pellets. For pellets with density that are twice the normal edge density and injected with a duty cycle of 1:2, the ELMs are generated on an average at a faster rate (~twice the rate of normal ELMs) and with reduced amplitudes (~50% of the average height of ELMs without pellets). These changes lead to significant improvements in the plasma beta indicative of an improvement in the energy confinement due to pellet injection. Furthermore, advanced spectral analysis of the data shows that in the presence of pellets there is an inward shift in the radial location of the ELMs and a spectral shift of the mode energy towards longer wavelengths. The shifts in the fluctuation spectrum with pellets are opposite to those of earlier RMP results in that pellets induce an inverse cascade while RMPs lead to a direct cascade of the energy. Both mechanisms however lead to an overall improvement in the plasma beta.

Speaker: Dr Debasis Chandra (Institute For Plasma Research, INDIA)

DChandra_TH5-1.pptx

sumslide_dchandra_th5-1_FEC18.pdf

FIP/2, FIP/3, MPT/1, SEE/1, MPT/2, FNS/1, SEE/2, SEE/3 P7 Posters

542 Active conditioning of ASDEX-Upgrade tunsgten PFCs through boron particulate injection

Speaker: Dr Robert Lunsford (Princeton Plasma Physics Laboratory)

Lunsford_IAEAFEC2018_FIP_2-3_final.pdf

543 Advances in predictive thermo-mechanical modelling for the JET divertor experimental interpretation, improved protection, and reliable operation

Speaker: Dr Daniel Iglesias (UK Atomic Energy Authority)

Iglesias-FEC-FIP2_v2.pdf

Iglesias-IAEA-FEC_v4 - talk.pptx

544 Amelioration of plasma-material interactions and improvement of plasma performance with a flowing liquid Li limiter and Li conditioning on EAST

Speaker: Dr Rajesh Maingi (Princeton Plasma Physics Laboratory)

Maingi_IAEA2018_final2_FIP:3-5a.pdf

Maingi_IAEA2018_poster_small.pdf

Maingi_IAEA2018_slide_FIP:3-5a.ppt

545 Development of a Lithium Vapor Box Divertor for Controlled Plasma Detachment

Speaker: Robert Goldston (Princeton Plasma Physics Laboratory)

Goldston FEC 2018 Squished.pdf

Goldston FIP 3-6 Single Slide.pdf

546 Development of physics and engineering designs for Japan's DEMO concept

Speaker: Dr Yoshiteru Sakamoto (National Institutes for Quantum and Radiological Science and Technology)

547 Economic Performance of Fusion Power Plant on Future Deregulated Electricity Market

Speaker: Prof. Shutaro Takeda (Kyoto University)

180927IAEA-Summary.pdf

548 Evaluation of Tungsten as Divertor Plasma-Facing Material: Results from Ion Irradiation Experiments and Computer Simulations

Speaker: Padivattathumana N Maya (ITER-India)

549 Experiments on FTU with a liquid tin limiter

Speaker: Dr Giuseppe Mazzitelli (ENEA)

IAEA_Mazzitelli_FIP:3-5Rb .pptx

550 Future Possibility of Carbon Sequestration by Biomass-Fusion Hybrid Systems

Speaker: Prof. satoshi konishi (kyoto university)

summary konishi.pdf

551 High-temperature creep properties of NIFS-HEAT-2 high-purity low-activation vanadium alloy

Speaker: Mr Takuya Nagasaka (National Institute for Fusion Science)

IAEA_FEC_2018_Nagasaka_vanadium_creep_1_page_summary_Ver2.pptx

552 Impact of High Field & High Confinement on L-mode-Edge Negative Triangularity Tokamak (NTT) Reactor

Speaker: Dr Mitsuru Kikuchi (QST)

553 Influence of Plasma Impurities on the Fuel Retention in Tungsten

Speaker: Dr Arkadi Kreter (Forschungszentrum Juelich)

554 Model validation on EAST and DIII-D experiments towards understanding of high-Z material erosion and migration in a mixed materials environment

Speaker: Dr Rui Ding (UsORAU)

Summary Slides

555 Novel Radio Frequency Current Drive Systems for Fusion Plasma Sustainment on DIII-D

Speaker: Dr Gregory Wallace (MIT Plasma Science and Fusion Center)

556 Overview of the DEMO Design-Staged Approach in Europe

Speaker: Dr Gianfranco Federici (EUROfusion Consortium)

557 Progress in Developing ITER and DEMO First Wall Technologies at SWIP

Speaker: Mr Jiming Chen (Southwestern Institute of Physics)

Summary slide for FIP2-1 of IAEA-CN-258 manuscript.pdf

558 Techno-economic analysis of biodiesel and hydrogen production via Fusion-Biomass Hybrid Model

Speaker: Mr Hoseok Nam (Kyoto University)

Summary Slide.pptx

559 Technologies for Plasma-Facing Wall Protection in EU DEMO

Speaker: Dr Thomas Barrett (Culham Centre for Fusion Energy (CCFE))

Summary Slide SummSlide_IAEA FEC_DEMO PF technologies_Barrett.pdf

560 The European approach to the fusion-like neutron source: The IFMIF-DONES Project

Speaker: Dr Angel Ibarra (CIEMAT)

561 Tritiated Dust: their impact on tokamak operation

Speaker: Mr Christian Grisolia (CEA)

562 Waste implications from minor impurities in European DEMO materials

Speaker: Dr Mark Gilbert (CCFE Fusion Association)

mgilbert_FEC_oct2018.pdf

mgilbert_summary_slide_FEC2018.pdf

P7 Posters

563 A toroidal confinement facility study and eventual experimental device to investigate a range of liquid metal divertor and first-wall concepts

A toroidal confinement facility study and development of a characteristic experimental device was undertaken to investigate a range of liquid metal divertor and first-wall concepts build on past and expected results from liquid metal experiments: the Lithium Tokamak Experiment (LTX), the National Spherical Torus Experiment Upgrade (NSTX-U), and the Experimental Advanced Superconducting Tokamak (EAST). The device configuration is driven by the need to adequately provide the concept details that depicts component features, space allocations, plumbing arrangements, thermal insulation, etc. of liquid metal systems. Of equal importance is to validate that the developed designs are upward compatible to exist within a blanket system of a DEMO or an eventual fusion power plant design. The proposed studies also builds upon recent low-A High Temperature Superconductor (HTS) tokamak pilot plant studies that incorporated a liquid metal divertor for high-heat-flux mitigation as a means of reducing poloidal field coil current and simplifying the magnet layout and maintenance schemes. Tokamak aspect ratios in the range of A = 1.8 to 2.5 would be considered based upon recent pilot plant studies indicating this range would be optimal for fusion power production if high-current-density HTS magnets were utilized. This aspect ratio range is subject to change pending the results of the first 1 to 1.5 years of the study. A current snapshot of a 1-m, 2.4m aspect ratio device configuration is illustrated in the included figure incorporating HTS magnets and a fast flowing liquid metal divertor/FW system. This paper will provide the design details of the Toroidal confinement facility – defining the general arrangement of the device configuration, details of the HTS magnet system and all LM system details investigated along with any engineering defined limitations or issues that may be expected when attempting to migrate the designs into the environment of a DEMO operated blanket defined system.

Speaker: Mr Thomas Brown (Princeton Plasma Physics Laboratory)

564 Advanced Assembly Technology of the Superconducting Coils in JT-60SA Tokamak

The JT-60SA is a superconducting coil tokamak, which is the project combined with Japanese national project and Japan-EU Satellite Tokamak Programme. The coil system is composed of 18 Toroidal Field (TF) coils, 6 Equilibrium Field (EF) coils and Center Solenoid (CS). The size of the TF coil is 7.5 m high and 4.6 m width. EF coils structures have 12 m in the maximum diameter. Thesse large components, which are over 10m size, must be assembled with high accuracy. In particular, tolerance of ±1 mm is required for TF coil assembly. In order to achieve such high accuracy at large components assembly, the follwong techniques are used: 1) 3D CAD is used for the confirmation of the fabrication tolerances, the designed position and interference at the intermediate assembly route. 2) Laser tracker is used for the positioning of the large components to know three dimensional data and to confirm the data in 3D CAD quickly. 3) Special jigs are used for the positioning of the components. The assembly procedure for the coil system including the final sector of Vacuum Vessel (VV) and Thermal Shield (TS) is established considering the above technique. The full-scale assembly of the JT-60SA started in 2013. In the actual assembly of the TF coil, all operation are proceeding successfully. This advanced technology can be also applied for the next machine, i.e. ITER.

Speaker: Dr Yusuke Shibama (NATIONAL INSTITUTES FOR QUANTUM AND RADIOLOGICAL SCIENCE AND TECHNOLOGY)

Summary_FIPP7-37_Y.Shibama.pptx

565 Advances in modelling of plasma pedestal behaviour and ELM control in ITER reference plasma scenarios

The achievement of ITER fusion performance is based upon plasma operational scenarios in which the plasma is in the high confinement regime (H-mode) during the burning phase. The fusion power production level is predicted to strongly depend on the values of the pedestal plasma temperature and density on the inner side of the edge transport barrier (ETB). Similarly, the steep edge density and temperature gradients in the ETB are expected to trigger Edge Localized Modes (ELMs) with large associated transient loads on plasma facing components that can severely reduce their lifetime in ITER. Although an intensive experimental R&D programme in ITER Members’ fusion facilities is presently addressing edge plasma stability issues and ELM control, significant uncertainties remain regarding the empirical extrapolation of the experimental results to ITER. Indeed the edge transport barrier plasma properties of ITER plasmas differ significantly from those in present experiments highlighting the need for a modelling based upon extrapolation of results from present experiments to ITER. In order to provide a firmer physics base to evaluate the edge plasma properties in ITER H-mode plasmas, the ITER Scientist Fellow Network pedestal group has been created. The group is formed by Fellow modelling experts from the ITER Members’ and ITER Organization staff and carries out a coordinated workprogramme together with a wider network of collaborators and addresses a range of issues covering edge MHD stability and transport in ITER plasmas, power, particle and impurity fluxes during ELMs, triggering of ELMs by active schemes such as pellet pacing and vertical oscillations and the application of 3-D fields for ELM control and their effects on edge stability, transport and rotation. The paper describes the significant progress in many of these areas that has been achieved through the coordinated work of the group.

Speaker: Dr Alberto Loarte (ITER Organization)

566 Assessment and optimization of the cavity thermal performance for the European Continuous Wave gyrotrons

The large Ohmic load (~20 MW/m2) of the wall of the resonant cavity of high-power gyrotrons, designed for tokamaks and stellarators for EC resonance heating and current drive to deliver a microwave power of the order of MW per unit, constitutes one of the major technological limiting factors, despite the small extension of the surface on which it is deposited. Even before reaching the material strength limits, the thermal deformation of the cavity is responsible for the gyrotron frequency shift with respect to its nominal operating condition. The proper modelling of the gyrotron cavity during long-pulse operation, including the assessment of its cooling capability, is mandatory for predicting the gyrotron performance as well as for the interpretation of experimental results. In Europe, the MUlti-physiCs tool for the integrated simulation of the CAvity (MUCCA) was developed in the last couple of years to compute the operating conditions of the gyrotron cavity accounting self-consistently for its thermal-hydraulic, thermo-mechanical and electro-dynamic behaviour. Since the validation of the numerical tool against data collected from the tests of the European 170 GHz 1 MW CW prototype gyrotron tested at KIT, which is cooled with forced-flow subcooled water passing through a porous highly-conductive copper matrix, is giving encouraging results, MUCCA is being applied to push the design of the cavity cooling to more effective solutions. In the paper, we present and discuss first the improvement of the cooling strategy of the cavity, aiming at decreasing the bell-shaped deformation by increasing the axial length of the porous region around the cavity. This solution has been implemented in the dual frequency 84/126 GHz, 1 MW, 2 s gyrotron, built for the upgrade of the TCV tokamak at SPC, EPFL, Lausanne and ready to be commissioned in the next months. Then, the ongoing design of a new cavity equipped with mini-channels is introduced, and the trade-off between increased cooling capability and increased pressure drop will be discussed. Finally, the status of the analysis of new cooling concept for the cavity, allowed by the presence of an insert inside the resonator in the so-called “co-axial” KIT gyrotron, is presented.

Speaker: Prof. laura savoldi (Dipartimento Energia Politecnico di Torino)

567 Assessment of Alternative Divertor Configurations as an Exhaust Solution for DEMO

The European roadmap for fusion energy has identified plasma exhaust as a major challenge towards the realisation of magnetic confinement fusion. To mitigate the risk that the baseline scenario with a single null divertor (SND) and a high radiation fraction adopted for ITER will not extrapolate to a DEMO reactor, the EUROfusion consortium is assessing potential benefits and engineering challenges of alternative divertor configurations. A range of alternative configurations that could be readily adopted in a DEMO design have been identified. They include the X divertor (XD), the Super-X divertor (SXD) and the Snowflake divertor (SFD). The flux flaring towards the divertor target of the XD is found to be limited by the minimum grazing angle at the target. The characteristic increase of the target radius in the SXD is a trade-off with the increased TF coil volume, but ultimately limited by forces onto coils. Engineering constraints also limit XD and SXD characteristics to the outer divertor leg with a solution for the inner leg requiring up-down symmetric configurations. Boundary models with varying degrees of complexity have been used to predict the beneficial effect of the alternative configurations on exhaust performance. Desired effects are an easier access to detachment, reluctance of the detachment front to move along the divertor leg and an increase of the divertor radiation without excessive core confinement degradation. Based on the extended 2-point model and achievable geometric variations the SOL radiation required for the onset of detachment decreases in the SXD and SFD with the tolerable residual power ∝(1-f_{rad}) being 30-40% larger than in the SND. Additional improvements are expected from the ability to increase frad without adverse effects on the core performance and through SOL broadening as postulated for the SFD. A systematic study of the alternative configurations and the SND reference using the divertor transport code TECXY confirms that the SFD detaches at a lower f_{rad}, but also shows that the potential gain is modest. The main expected advantage of the XD and similarly of the SXD is an increased reluctance of the detachment front to move towards the X-point. To that end the detachment dynamics are assessed with the SOLPS and SOLEDGE2D-Eirene codes, which use more sophisticated models of the target geometry and neutral particles.

Speaker: Dr Holger Reimerdes (Ecole Polytechnique Fédérale de Lausanne (EPFL), Swiss Plasma Center (SPC), Lausanne, Switzerland)

Summary_IAEA_FEC_Reimerdes.pdf

568 Bifurcation of Perpendicular Rotation and Field Penetration at the Transition to RMP-induced ELM-crash Suppression

The bifurcation of perpendicular rotation ($v_{\perp}$) at the transition of ELM-crash suppression has been measured using electron cyclotron emission imaging (ECEI) system on KSTAR. The ECEI revealed that the ELM crashes are suppressed along with a rapid reduction of $v_{\perp}$, which synchronizes with the transition into and out of the ELM-crash suppression. The $v_{\perp}$ bifurcation is mainly attributed to the rapid change of $E \times B$ velocity and the $v_{\perp}$ magnitude is maintained the smallest near the $q_{95}$ rational flux surface during the ELM-crash suppression. The plasma response to the RMP, normalized by $v_{\perp}$ changes, is strongest in the vicinity of $q_{95}$ rational flux surface during the ELM-crash suppression.

Speaker: Dr Jaehyun Lee (National Fusion Research Institute)

FEC2018_summary_Jaehyun.pdf

569 Characteristics of Asymmetric (low-field-side and high-field side) Divertor Detachment in KSTAR L-mode Plasmas

A divertor detachment experiment in low confinement mode and $B\times \nabla B$ into the divertor was performed in KSTAR to investigate various divertor operation regimes. The low field side (LFS) target parallel particle flux $\Gamma_{\parallel}$ started roll-over first ($n_{e} = 2.0-2.5 \times 10^{19} m^{-3}$), and then the high field side (HFS) target $\Gamma_{\parallel}$ began roll-over at the higher upstream electron density ($n_{e} = 2.5-3.0 \times 10^{19} m^{-3}$). The observed detachment pattern is similar to the one in TCV [1] and opposite to JET and ASDEX-U [2]. Numerical simulations using the SOLPS-ITER code [3] with different electron density values were performed to identify the physics behind the detachment behaviour observed in the experiment. The simulation result is qualitatively consistent with the experiment in terms of the roll-over pattern of the total particle fluxes on the targets. Pressure and power losses were decomposed into source terms including the kinetic neutral reactions. The dominant pressure and power loss mechanisms were identified in each SOL rings. In the high recycling condition (electron density at the separatrix, outer mid-plane $(n_e)_{sep}^{OMP}≥ 1.49\times10^{19} m^{-3}$), volumetric reactions govern power and pressure losses along the flux tube, however the dominant reaction type depends on the radial position of the SOL ring. According to the recycled neutral deuterium particle trajectory observed in the code, $D_{2}$ molecules accumulate behind the divertor structure through a gap near the LFS target. The gap acts as a strong neutral particle source near the LFS target, resulting in a 2–10 times larger $D_{2}$ density at the LFS than at the HFS target. The simulations predict that this asymmetric neutral particle distribution causes divertor asymmetry. The accumulated $D_{2}$ enhances detachment, which is related to the strong correlation between the target $D_{2}$ density $n_{D2t}$ and the target electron temperature [4]. This correlation results from additional power and pressure losses by the molecular related reactions, such as dissociation and charge exchange. [1] R. A. Pitts et al, J. Nucl. Mater. 290, 940 (2001) [2] A. Loarte et al, Nucl. Fusion 38, 331 (1998) [3] S. Wiesen et al, J. Nucl. Mater. 463 480 (2001) [4] P. C. Stangeby and C. Sang, Nucl. Fusion 57, 056007 (2017)

Speaker: Mr Jae-Sun Park (Korea Advanced Institute of Science and Technology)

Summary_slide.pdf

570 Collisional Merging of a Field-Reversed Configuration in the FAT-CM Device

The collisional merging experiments of field-reversed configurations (FRCs) at super Alfvénic velocity have been successfully initiated in the FAT-CM device at Nihon University. Drastic increase of the excluded-flux leading to the improved confinement performance of FRC has been observed. This process has an important role to realize FRC based high-beta reactor core to capture high-energy beam ions and it has been clearly observed by magnetic diagnostics of excluded flux and internal probe array. The experimental results are compared with 2D MHD simulation results computed for the typical condition of the FAT-CM experiments. In order to investigate the collisional merging process of a FRC at super Alfvénic velocity, the FAT device has recently been upgraded to FAT-CM, consisting of two field-reversed theta-pinch (FRTP) formation sections and the central confinement section. Collisional merging of the two separately translated FRCs causes a conversion of the kinetic energy to mostly thermal ion energy, which contrasts with the spheromak merging dominated by magnetic energy, resulting in an increase of the ion pressure that drastically expands the FRC volume. The confinement chamber of FAT-CM device is made of stainless steel (inner bore is 0.78m) serving as a flux conserver in the timescale of the translation and merging process. Quasi-static confinement coils (inner diameter of 1.03m) are placed along the confinement region. Initial FRCs are formed by the FRTP method in two formation sections. The initial FRCs are accelerated by the gradient of the external guide magnetic field and then injected into the confinement chamber. The translated FRCs collide in the middle of the confinement chamber at the relative velocity in the range of 300 - 400 km/s. By the collisional merging, radial expansion of the plasma is clearly observed and the plasma size, in the quasi-equilibrium phase, increase more than twofold compared with the single translation case. The averaged electron density of the merged FRC is ~2.5 × 10^20 /m^3, which is ten times higher than the previous experiments performed in C-2U device at TAE. The shape of the simulated FRC agrees with experimental results. This also indicates a successful merging of the FRCs, and resulting in the radial expansion and excluded-flux increase due to the collisional merging, as observed in experiments.

Speaker: Prof. Tomohiko Asai (Nihon University)

SummarySlide.pptx

571 Comparative analysis of the SOL properties for the various magnetic configurations proposed for the DEMO divertor

The mitigating properties of the divertor advanced magnetic configurations on the target heat load have been analysed with the 2D edge code TECXY for the European DEMO. Particular emphasis is put on the snowflake minus, for which several variants have been proposed just to study this particular effect, where the distance between the two X points, the primary and secondary ones, is varied. In such a way the magnetic topology in the outboard part of the divertor is varied and regions with low poloidal field and then much longer connection length are created with different extension and localization with respect to the primary X point. The scenario considered is a low density one, without any added impurity in order to keep at a negligible level the effect of radiative volume losses and then to ascribe any possible change to the transport properties of each configuration. A significant widening of the power flow channel in term of the poloidal flux coordinate, i.e. independent of any expansion effect, is found and correspondingly a drop of the peak power load. The mitigation effect increases for these configurations that more affect the region in close touch with the main separatrix. The possible causes for this effect are discussed in the paper. However some manipulation is required to make the real magnetic topology compatible with the constraints of TECXY, which allows for only two targets. Even if the modifications affect only the more external flux tubes that have less weight in the power transport, the results clearly claim for confirmation by other more complex codes.

Speaker: Dr Vincenzo PERICOLI RIDOLFINI (PoIPP)

2018DEMOvariousMagConf_TECXY(IAEAsummary_VPR).pptx

572 Conceptual Design of a Compact Helical Fusion Reactor FFHR-c1 for the Early Demonstration of a Year-long Electric Power Generation

Conceptual design of a compact LHD-type helical fusion reactor FFHR-c1 has been conducted. This design focuses on a year-long electric power generation with as small a reactor size as possible by adopting the operation with auxiliary heating and innovative ideas for the design of engineering system. This design ensures the path to helical commercial power plants through the examination of confinement scaling and steady-state operation test of engineering components. Though intensive R&Ds are needed, the innovative ideas provide more options and increase the probability of solving critical issues of fusion reactors: accommodation of high heat and particle load on the divertor, construction and maintenance within a reasonable period. The candidate design point of FFHR-c1 has been identified using the systems code HELIOSCOPE. A smaller reactor with the same plasma confinement property can be realised by increasing the magnetic field. However, the size reduction is limited by the decrease of the thickness of the neutron shield in the blanket system. In this regard, the adoption of supplementary helical coils can increase the blanket space by $\sim$ 15%. Finally, the design point with the major radius of 10.92 m, the magnetic field on the helical coil winding centre of 7.3 T and the fusion gain $Q \sim$ 10, which can achieve positive net electric power with a minimum reactor size, have been selected. To confirm the feasibility of the core plasma design, integrated physics analysis has been conducted. The magnetic configuration with a high aspect ratio and inward-shifted magnetic axis position was assumed. As a result, $Q \sim$ 15 can be achieved within the operation regime that has already been confirmed in the LHD experiment: the Mercier index $D_I$ < 0.3 at the $n/m$ = 1/1 rational surface and the neoclassical energy loss lower than a half of the total absorbed power. Although there are some issues to be solved (e.g., design of the helical coils with a current density of > 40 A/mm$^2$, achievement of the peak beta value of $\sim$ 3% with an inward-shifted configuration), this comprehensive study has shown the design feasibility of a compact LHD-type helical reactor that can satisfy the requirements on Japanese fusion DEMO: steady-state electricity generation above several hundred MW, tritium fuel self-sufficiency and practical availability.

Speaker: Dr Takuya Goto (National Institute for Fusion Science)

IAEA-FEC27_FIP_P7-39_TGoto_1page_summary.pdf

573 Continuum Gyrokinetic Simulations of NSTX SOL Turbulence with Sheath-Limited Model Geometries

We describe results obtained from Gkeyll, a full-F continuum gyrokinetic code, designed to study turbulence in the edge region of fusion devices. The edge region is computationally very challenging, requiring robust algorithms that can handle large amplitude fluctuations and stable interactions with sheath boundary conditions. Results of turbulence in a scrape-off layer (SOL) for NSTX-type parameters with a model magnetic geometry have been obtained. Key physics of SOL turbulence, such as drive by toroidal bad curvature and steep gradients and interactions with a model sheath boundary condition are included. This allows us to perform parameter scans and physics studies, such as the physics of heat flux width on the divertor plate, and the amplitude and intermittency of SOL turbulence. Initial results find that the heat flux narrows as the connection length is made shorter (the poloidal field becomes stronger). We have begun studies on the effect of recycling on the edge, to better understand low-recycling lithium cases. To validate the code, we have studied turbulence in the straight-field LAPD device at UCLA and the helical Helimak device at the University of Texas. We will also describe the extension of the GENE gyrokinetic code to be full-F, and initial GENE simulations for LAPD.

Speaker: Mr Ammar Hakim (Princeton Plasma Physics Laboratory)

Hakim-A-TH-Slide.pdf

574 Conversion of electrostatic Bernstein waves in the SCR-1 Stellarator using a full wave code

The small modular SCR-1 Stellarator (R = 247.7 mm, R/a = 6.2, ιa = 0.264) has an ECRH system of 2.45 GHz (5 kW) with an average magnetic field of 41.99 mT [1]. Few studies on conversion of electrostatic Bernstein waves under these conditions have been performed in Stellarators [2,3]. This work presents the results of converting electrostatic Bernstein waves in the SCR-1 Stellarator using the full wave code IPF-FDMC [3], taking the 3D magnetic field obtained by VMEC code as input and the experimental electron density profile obtained using a Langmuir probe. New microwave heating scenarios that take the SCR-1's vacuum vessel into account in order to improve the O-X conversion due to reflection of the incoming radiation from the ECRH system are presented. The percentage of single pass O-X mode conversion is around 3%. The design of an antenna with its characteristics and locations according to the SCR-1 viewports is explained. Other important aspects of this work are focused on the BS-SOLCTRA (Biot-Savart Solver for Compute and Trace Magnetic Fields) code, developed by our research group, and its way to convert it into a parallel and high-performance computing platform. This code allows calculations of the 3D vacuum magnetic field and the visualization of the magnetic flux surfaces at SCR-1. Similarly, the results of the comparison of the flux surfaces measured with an electron beam and different kinds of fluorescent rods with computed flux surfaces by means of the BS-SOLCTRA code are shown. Finally, magnetic and energy diagnostics have been developed with special requirements based on the SCR-1 geometry so the design, data analysis tools and measurement technique are introduced. References [1] V I Vargas et al 2015 J. Phys.: Conf. Ser. 591 012016. [2] R. Ikeda et al, Physics of Plasmas, 15, 7, (2008). [3] A. Köhn et al, Plasma Physics and Controlled Fusion 55, 1 (2013).

Speaker: Dr Ivan Vargas-Blanco (Instituto Tecnológico de Costa Rica)

Vargas VI - EXW - Slide.pdf

575 Design and Thermal Fluid Structure Interaction Analysis of Liquid Nitrogen Cryostat of Cryogenic Molecular Sieve Bed Adsorber for Hydrogen Isotopes Removal System

Efficient design of Tritium Extraction System (TES) for the fuel cycle of any fusion reactor is very important to maintain the tritium breeding ratio and hence sustain the fusion reaction. Hydrogen Isotopes Removal System (HIRS) for Indian Tritium Breeder Blanket removes Q2 (Q = H, D or T) and impurities using Cryogenic Molecular Sieve Bed (CMSB) adsorber at 77K. The CMSB is maintained at liquid nitrogen temperature using a double walled cryostat made up of SS 304L. This paper describes the design and thermal Fluid Structure Interaction (FSI) analysis of cryostat assembly for CMSB of HIRS. The coupled analysis performed in this work involves solving for the fluid domain and transferring the results to ANSYS Thermal-Static Structural set up to determine the stresses and displacement due to combined effects in the system. The mechanical design of the cryostat components is analytically performed using ASME codes. The velocity, pressure drop and time taken to cool the CMSB are determined by solving the fluid and energy equations in ANSYS Fluent Analysis System. The solutions are imported into ANSYS Thermal-Static Structural analysis system and the thermal-structural stresses and deformations are determined considering the temperature, pressure and acceleration loads. The space between inner and outer vessel is maintained at vacuum, which might lead to buckling. So, the critical buckling load multiplier factor is determined. The modal analysis is also performed to determine the fundamental frequency of vibration of the structure. These results would be used in fabricating the complete cryostat system for CMSB of HIRS.

Speaker: Ms Gayathri V. (Institute for Plasma Reserch, India)

576 Design of the TF/PF Bus Bar lay out and its connections with Current Feeder System of SST1 Tokamak

Steady state super conducting Tokamak (SST-1) is an indigenously built working experimental Tokamak at Institute for Plasma Research (IPR). The primary magnetic configurations and plasma shaping magnetic requirements are provided by Superconducting Magnet Systems (SCMS) comprising of sixteen superconducting D-shaped Toroidal Field (TF) magnets and nine superconducting Poloidal Field (PF) magnets together with a pair of resistive PF coils inside the vacuum vessel. The current feeding system of TF & PF magnets consists of power supplies, current carrying bus bar and its connections with current leads at room temperature on one side and other side at 4.5 K with SCMS. Current Lead Chamber (CLC), which contains the super conducting current leads of Toroidal Field (TF) and Poloidal Field (PF) coils inside the vacuum chamber, has to be connected outside the vacuum chamber to the current feeder bus bars at room temperature. These bus bars are required to be supported with the proper support structure without any interference with the nearby components.The design of the bus bar layout along with its support structures to withstand the static and electromagnetic load and bus bar connections with current feeder system will be presented in this paper.

Speaker: Mr bharatkumar doshi (Institute for plasma research)

577 Design optimization of Helium cooling systems for Indian LLCB TBM

India is developing the lead–lithium cooled ceramic breeder as the blanket concept to be tested in ITER. In the Indian Lithium cooled Ceramic Breeder (LLCB) Test Blanket Module (TBM), PbLi eutectic alloy is used as multiplier, breeder, and coolant for the CB zones, and Li2TiO3 ceramic breeder (CB) is used as a tritium breeding material. The outer box structure is made of India specific Reduced Activation Ferritic Martensitic Steel (IN-RAFMS) cooled by high pressure (8.0 MPa) and high temperature (300-500 C) helium gas named as First Wall Helium Cooling System (FWHCS). The Pb-Li flow velocity is kept moderate enough such that its self-generated heat and the heat transferred from the ceramic breeder bed is extracted effectively. The Pb-Li system is cooled by another high-pressure helium system named as lead-lithium helium cooling system (LLHCS). Eventually, the two helium systems transfer the heat to Component Cooling Water System (CCWS) of ITER. In the conceptual design of LLCB TBM and its ancillary systems, two independent helium circuits were considered for extracting heat separately from the FW and the Pb-Li system. These helium systems are thermally and hydraulically independent to each other and they have their own components for operation and control. However, after detailed study, it is found that Installation and assembly of all these components along with coolant purification system in the allocated space of Tokamak Cooling Water System (TCWS) vault annex is very difficult and the existing system to be optimized to fit into the space. Accordingly, studies were carried to reduce the number of components & their sizing and schemes to combine the two independent helium systems etc. In parallel, studies were also conducted to optimize the helium flow requirements for cooling the TBM FW. In the optimized configuration, a single helium system is proposed catering the cooling requirements of FW and Pb-Li system and the main components and piping of the optimized configurations of helium system are modeled in the modified version of RELAP/MOD4.0 and transient analysis is carried out. This paper discusses the results of the optimization studies and process parameters & features of the circuit diagram of the combined helium system. Thermo-hydraulic Analysis results with the chosen optimized process parameters of the First Wall are also presented.

Speaker: Mr Brijesh Kumar Yadav (Institute for Plasma Research, Bhat, Gandjinagar, India)

summary slide.pptx

578 Development and experiment of PbLi facilities for fusion nuclear technology

The liquid lead-lithium (PbLi) blanket concept has become a promising design for fusion DEMO and power plant reactors. To promote the successful application of fusion energy, some R&D; activities on the PbLi blanket have been performed, such as structure material corrosion, thermal hydraulics, magnetic-hydrodynamic (MHD) effect, coolant impurities technology and LOCA/LOFA, etc.. Therefore, it is so important to develop experimental facility to perform the out of pile experiments and studies on these key issues before the engineering design of fusion reactor.

Series DRAGON PbLi experimental loops have been developed and constructed in China, including the thermal convection PbLi loops DRAGON-I (500ºC) and DRAGON-II (700ºC), and the multi-functional liquid PbLi experimental loop DRAGON-IV (800ºC, 2T). To perform the integrated experiments under the multi-physical field conditions for DEMO blanket, the dual coolant thermal hydraulic integrated experimental loop DRAGON-V was designed and finished the construction in 2017. It is composed of a lead-lithium loop and a helium gas loop. The maximum flow rate of PbLi and helium gas pressure are 40 kg/s and 10.5 MPa, respectively. The magnetic field is designed up to 5T. It is a unique test platform for the R&D; of thermal hydraulic, material corrosion, purification technology and safety issues of liquid PbLi blanket to provide the necessary database for ITER-TBM and DEMO-TBM.

Up to now, some experiments have been conducted to investigate the key issues of PbLi technologies, such as corrosion behaviors of candidate structural materials with and without magnetic field, the PbLi alloy fabrication with high-level controlling of the impurities, purification technology of liquid PbLi coolant in the loop, MHD pressure drop test, and the interaction for typical coolants during accidents etc.. The results can support the development of the in-pile key techniques and components and the engineering design for ITER-TBM and DEMO-TBM, and also contribute to the final application of the advanced reactors.

Speaker: Dr Dehong Chen

One slide summary for FIP P7-29.pdf

579 Development of a plasma scenario for the EU-DEMO: current activities and perspectives

In order for the first fusion reactor DEMO to accomplish its mission, it is necessary to identify a plasma scenario which is at the same time performing in terms of fusion power generation and sufficiently stable to ensure the integrity and availability of the machine components for a long time. In the present work, the activities undertaken for this purpose by EUROfusion PMU are summarized. In the course of the current pre-conceptual design analysis phase for the European DEMO, it is necessary to define scenarios by considering from the early phases their compatibility with the performance of the available diagnostics, of the actuators for plasma control and with the response of the heating and current drive systems. A coupling between the 1D transport code ASTRA and the control software Simulink has been performed, providing a tool able to simulate the plasma behavior while accounting for the constraints linked to the detectability of the signals and the delay and power limitations of the actuators responses. In our work, the DEMO-related results of such a tool are presented. In parallel, the numerous ongoing activities concerning the open issues which require to be addressed before the scenario could be considered complete and robust enough (e.g. plasma ramp-up and –down definition, identification of disruption precursors, ELM mitigation etc.) are also illustrated. The reference scenario which is considered for the EU-DEMO is the so called “DEMO 1”, i.e. a pulsed scenario based on conservative physics assumptions and analogous, at least from a macroscopic level, to the ITER 15 MA. However, other, alternative scenarios are investigated in parallel. The main alternative concept developed is the so called Flexi-DEMO, which relies on more advanced scenarios as compared to DEMO 1, with a large fraction of auxiliary current drive and a tailoring of the safety factor profile which aims at maximizing the bootstrap current fraction to achieve a steady-state discharge. Furthermore, the possibility of extrapolating other, more speculative scenarios to a reactor condition is also considered inside our activities.

Speaker: Dr Mattia Siccinio (EUROfusion Consortium)

OneSlideSummary_IAEA_FEC_2018_Siccinio.pptx

580 Development of a Prototype Collaborative Robot for Fusion Remote Handling Applications

Remote handling (RH) systems are highly challenging for application in the maintenance of fusion devices. The challenges include accurate handling of very heavy payloads using long cantilevered robotic arms with a dexterous manipulator. For the flexibility to execute dynamic tasks safely, these manipulators are typically controlled using a ‘man in the loop’ architecture. Haptic systems with real-time force feedback integrated to full 3D virtual reality environment can enable the RH operators to have the sense of virtual presence. These are highly complex systems requiring integration of several technologies with a closed loop control system. One modern approach for handling such application can be by the development of collaborative robot mechanisms. A collaborative robot is a robotic device designed to assist human beings as a guide or assistor in a specific task. It can assist a human operator semi-autonomously during the task as if it were a real mechanical tool and improves the manoeuvrability and the efficiency in the teleoperation. The collaborative robot mechanism with human-robot interactions in a shared workspace can be used as a training platform for the operators to check the feasibility and optimize the operation sequences for planning the RH tasks. This can be extremely beneficial to reduce the duration of maintenance cycles and to maximize the availability of the fusion device for plasma operations. In this work, a concept is developed for a tokamak relevant collaborative robot mechanism followed by implementation of a prototype system. The system uses back-drivable actuators with force feedback in the closed loop control system. High precision encoders are used to measure the joint movements and mapped in the control system. The system aims for the development of a low friction, efficient system for fusion RH requirements and can act as a training platform for the RH operators.

Speaker: Mr Naveen Rastogi (Institue for Plasma Research)

summary slide.pdf

581 Development of Capacitively-Coupled Combline Antennas for Current Drive in Tokamaks

The capacitively-coupled combline (CCC) antenna has been developed for current drive by the lower hybrid wave (LHW) on the TST-2 spherical tokamak. In order to excite a highly directional wave required for efficient current drive, an antenna array consisting of many elements is necessary, but it is impractical to feed each of these elements independently in a device with limited accessibility. The combline antenna was developed to satisfy the requirements of high directionality, low reflectivity, and simple feeding. Since the combline antenna makes use of mutual coupling between neighboring elements, only the first and the last elements are connected to external feedlines. Each element is an L-C resonant circuit, coupled to neighboring elements by mutual capacitance, and exhibits a passband characteristic. The copper capacitive elements are shaped so that the RF electric field extends well into the plasma. The inductive elements are covered so neighboring elements do not couple inductively to each other and the RF magnetic field does not extend into the plasma. Faraday shield is not necessary. RF powers and power densities of the order of 100 kW and 1 MW/m $^2$ can be achieved easily in small antennas of the order of 0.1 m$^2$, because of the inherently low standing wave ratio. The two CCC antennas installed in TST-2 (outboard-launch and top-launch) excite toroidal refractive index ($n_\phi$) spectra peaked around 5 with full width at half maxima of around 2. Wave excitation calculation using COMSOL Multiphysics shows that the excited power of the $n_\phi$ = 5 LHW component increases rapidly when the plasma cutoff density layer (where $n_e = 5 \times 10^{14}$ m$^{-3}$) becomes closer than 27 mm from the antenna surface, in agreement with experiment. Experimentally, the density profile in front of the antenna can be controlled by adjusting the side limiter location or antenna-plasma distance, and should be optimized for antenna-plasma coupling, since too high coupling results in a broadened and less directional $n_\phi$ spectrum, and too low coupling results in a less efficient power coupling, which necessitates recirculation of the transmitted power. Using these antennas, successful ST plasma start-up and $I_p$ ramp-up to over 25 kA (about 1/4 of the nominal $I_p$ for OH operation) have been achieved with RF power of less than 100 kW in about 40 ms.

Speaker: Prof. Yuichi Takase (University of Tokyo)

FIP_P7-4.pdf

582 Development of DEMO-FNS fueling systems and modeling hydrogen isotopes distribution via «FC-FNS» simulation code

In the NRC “Kurchatov Institute” fueling systems (FS) concept for the DEMO-FNS facility incorporating components maintaining plasma parameters, tritium processing and breeding, is being developed. The FS computer model provides calculation functions using the computer code «FC-FNS». It allows to calculate gas flows, tritium inventories and losses in FS for steady-state operation mode. Within the DEMO-FNS design development the device parameters were better specified and «FC-FNS» code was upgraded accordingly. In 2016-2018, the structural diagram of fuel cycle was expanded to include systems for fuel mixture deprotiation, cooling the divertor and first wall, tritium extraction from lithium circulating in the vacuum vessel. The code functionality was expanded to take into account the new systems and operating modes. The updated version simulates the balance of all three hydrogen isotopes (H, D, T). The values of tritium inventory in main systems (blanket, storage, processing and separation) calculated on the basis of the particle balance can be compared with those obtained using solution of differential equations describing the dynamics of tritium inventories. Due to the fact that the neutral beam injection (NBI) system is included in the FS, its gas supply configuration and integration in the facility FS are being considered. Calculations showed that in a neutral injection system it is inappropriate to use D:T = 1:1 gas mixture. The scenario is optimal in which a tritium-containing gas mixture is pumped out to the facility's FS when a specified tritium fraction (5%) is reached. The total tritium inventory in FS can be reduced to 1.5-2 times compared with 1:1 case. Previously, the particles balance was set on the assumption that injection systems must compensate the particles loss from plasma due to burnout and removal of hydrogen isotopes from the plasma. The new code version includes the possibility to simulate the gas inlet to the vacuum chamber associated with control of the edge plasma parameters, ELMs control, etc. Tritium losses in the FS reach 30-50 g due to its decay and about 20 g due to diffusion through the structural materials in addition to the burnout of 1.7 kg per year in plasma. Tritium inventories in structural materials reach up to 90 g per year. In this case, the total amount of tritium in the FS will be up to 1000 g.

Speaker: Dr Sergey Ananyev (NRC "Kurchatov Institute")

Ananyev_-_summary.pptx

583 Early definition of the maintenance plan is essential to achieve an economic EU DEMO

The development of fusion as a viable power source is moving from the science driven design of experimental devices to the engineering design considerations required to develop a feasible power plant. An effective maintenance plan is essential because the time in maintenance is potentially very large. To be effective a maintenance plan must be outlined early in the plant design because it has two key requirements that must be embedded from the outset of the plant layout. First it requires the efficient transport of components and equipment around the plant through corridors, shield doors and contamination control systems using the most appropriate transport system. Second it requires maintenance-oriented strategies to reduce the maintenance burden and to achieve the maintenance in a shorter time, with lower risk of failure and with simpler recovery scenarios. Work is therefore required at the pre-concept design stage to define the maintenance plan so that the design driving factors required to enable the plan can be embedded in the plant design from the outset. This paper will describe this work, including the key transport system that has been proposed for the transfer of components and equipment to and from the tokamak using ceiling mounted cranes and dexterous manipulator systems. A qualitative comparison will be made between the proposed system and an alternative cask-based system will be made. The paper will also briefly describe some of the proposed maintenance-oriented strategies and development and testing work that is being carried out to mitigate the technical risks associated with the proposed maintenance plan. This work has been carried out within the framework of the EUROfusion Consortium and has received funding from the Euratom research and training programme 2014-2018 under grant agreement No 633053 and from the RCUK Energy Programme [grant number EP/P012450/1]. The views and opinions expressed herein do not necessarily reflect those of the European Commission.

Speaker: Mr Oliver Crofts (RACE UKAEA B1 Culham Science Centre, Abingdon, Oxon, UK)

OC FEC summary slide v1.0.pdf

584 Effects of Lithium Coating of Chamber Wall on the STOR-M Tokamak Discharges

In a recent experimental campaign in the STOR-M tokamak (*R/a* = 0.46/0.12 cm, *Bt* =0.65 T, *Ip* =22 kA), approximately 100 mg of lithium per load has been evaporated from a heated lithium reservoir and coated on the stainless-steel inner wall to study its effects on the tokamak discharge. The evaporators were designed, developed and supplied by General Fusion Inc.. Although four evaporators are available, only one evaporator has been used at present time. Coating of lithium on the surface visible by the evaporator through line-of-sight is expected and rest of the surface may be coated during the discharge through spattering and redistribution of coated lithium due to plasma-wall interaction. It has been found that the partial pressure of impurities such as H2O, CO and CO2 reduces significantly immediately after coating, possibly due to gettering effect of lithium coating. During the discharge, the total pressure is also reduced, indicating reduced recycling of gas from the wall. Line emission intensity of selected impurity ions (CIII, OV and CVI) clearly reduces. Correspondingly, the peak plasma current increases by 20% and discharge duration increases significantly. The line averaged electron density reduces by more than 50% due to reduced fuel recycling. The loop voltage reduces by a proximate 1/3 due to reduced impurity. An increase in hard x-ray radiation has also been observed, suggesting an enhanced generation of supra-thermal runaway electrons at lowered electron density. The density reduction can be restored by refuelling via compact torus injection.

Speaker: Prof. Chijin Xiao (University of Saskatchewan)

OnePage Slide-EX-P7-11.pptx

585 Effects of Reconnection Downstream Conditions on Electron Parallel Acceleration during Merging Start-up of Spherical Tokamak

Axial merging method is one of the candidates to provide center-solenoid-free start-up of high beta spherical tokamak (ST) plasma, in which two initially formed STs merge through magnetic reconnection in the presence of the guide (toroidal) magnetic field, which is perpendicular to the reconnection (poloidal) magnetic field. Magnetic reconnection between two STs is capable of heating the electrons in the vicinity of the reconnection point, however, its mechanism has not been identified in laboratory experiments yet. During ST merging start-up, electrons are effectively accelerated near the reconnection point where the reconnection electric field is approximately parallel to the magnetic field and will provide the local electron heating. In order to observe the spatial distribution of generated energetic electrons, the SXR (> 100 eV) emission profile was observed by a fast imaging system equipped on the UTST device. High-intensity SXR emission was observed particularly in the early reconnection phase when the SXR emission profile spread widely in the inboard-side downstream region. ｓSince the reconnection electric field had only toroidal component in the ST merging case, and large parallel component of the electric field in the inboard-side downstream region served to accelerate electrons along the field lines. In the middle merging phase, the SXR emission was clearly localized on two separatrix arms, which correspond to the magnetic field lines on which the electrons toroidally accelerated at the reconnection point will move. Though high toroidal reconnection electric field was still induced in the downstream region, its parallel component was cancelled by the charge separation mostly due to the electrons’ motion. A test particle calculation was carried out based on the experimentally measured magnetic and electric fields. Here, we assume that the parallel electric field in the downstream region is cancelled in the middle merging phase. The energetic electrons are generated in wide area of the downstream region in the early merging phase, possibly accounting for the broad electron heating. Then, the acceleration occurs only on the reconnection separatrix in the middle merging phase, indicating the localized electron heating near the reconnection point.

Speaker: Prof. Michiaki Inomoto (The University of Tokyo)

inomoto_180927.pptx

586 Electron Impact Excitation of W^40+ to W^43+ Ions: Cross Section and Polarization

Tungsten has been planned to be used in the diverter region of International Thermonuclear Experimental Reactor (ITER) as it has the highest heat load capacity, highest melting point and more other favourable physical properties among the metals. Distinct ionic states of tungsten are predicted to be present from divertor to core of the ITER device. Thus, to understand the radiation emissions coming from the diverter region plasma, detailed and complete set of atomic data of electron impact excitation cross sections of various ionized tungsten ions in the wide energy range is required. In fact, such data are prime input in the plasma modeling. In addition to electron impact excitation there is also probability of photon emissions from the decay of these electron these excited states. Hence it may be important to study the linear polarization of photons emitted from these excited states to add to the understand the diagnostics of the ITER plasma. Recently Ralchenko *et al.* [1] measured spectral lines in the range 12-20 nm and Utter *et al.* [2] measured spectral line in the range 4-8 nm coming from the charged states of tungsten ions produced in the electron beam ion trap (EBIT) facility at the Gaithersburg and Livermore respectively. In the light of these experiments, we have identified some lines in Se-like W^{40+} to Ga-like W^{43+} tungsten ions and calculated the electron impact excitation cross sections for the corresponding fine structure transitions. We found that there are no theoretical or experimental data of cross section and polarization are available in the literature for such lines. In order to describe the electron impact excitation, process we used fully relativistic distorted wave theory. Using these cross sections and density matrix theory, we further calculated polarization of the emitted photons as a result of decay of the electron from excited states. The detailed results of the cross sections and polarizations for various transitions in different ions will be presented in the conference. References: 1. Yu Ralchenko et al., 2007, J. Phys. B **40**, 3861 2. S. B. Utter, P. Beiersdorfer, and E. Trabert 2002, Can. J. Phys. **80**, 1503

Speaker: Ms Neelam Shukla (IIT Roorkee)

summary slide.pptx

587 ELM Suppression and Internal Transport Barrier Formation by Krypton Seeding in KSTAR Plasmas

Impurity seeding with noble gases, such as krypton (Kr), is regarded as a promising way to mitigate divertor heat loads. In this study, ELMs were successfully suppressed by Kr injection in the KSTAR divertor region and the relation between ELM behaviour and Kr amount was studied in KSTAR plasmas with 0.5 MA plasma current and 2.5 T toroidal field. Figures 1(a)-(c) show the plasma parameters with different levels of Kr injection. After achieving an intermediate level of Kr seeding, ELM crashes were briefly suppressed and grassy ELMs occurred with slight reduction of line-integrated electron density, core electron temperature and stored energy, while there was no effect on ELMs for a low level of Kr. The ELM suppression time became longer at a higher level of Kr injection. Figures 1(d) and 1(e) represent the same background plasma parameters at intermediate and high injection levels seen in Figures 1(b) and 1(c), respectively, but with the presence of on-axis ECH. Compared to Figure 1(c), longer and more stable ELM suppression was possible with a high level of Kr injection with ECH (Figure 1(e)). Detailed analysis including peeling-ballooning stability is on-going to understand the ELM suppression mechanisms with Kr profiles and ECH. At a certain level of Kr injection, an internal transport barrier (ITB) was formed after ELM mitigation and it was maintained until the termination of the plasma. As shown in Figure 2(a), core electron temperature, stored energy and Dα signal gradually decrease after Kr injection at 6.0 s. After a sudden increase of core electron temperature at 10 s, electron and ion temperatures and toroidal rotation profiles show strong central peaking (Figure 2(b)), which are the commonly observed feature of an ITB. Both electron and ion heat diffusivities at the plasma core, obtained by TRANSP calculation, also drop significantly after ITB formation, which suggests the reduction of core thermal transport or improvement of core thermal confinement. Two-dimensional radiation profiles obtained by the imaging bolometer diagnostic show off-axis Kr accumulation after ITB formation, while Kr was accumulated mainly in the plasma core before the ITB. Detailed analysis of Kr impurity transport is on-going to investigate the role of Kr impurity on ITB formation.

Speaker: Mr Juhyeok Jang Jang (Korea Advanced Institute of Science and Technology)

FEC_presentation_summary_J.Jang.pptx

588 Error field experiment and analysis in SST-1

The SST-1 Tokamak has 16 numbers of toroidal field (TF) coils and 9 numbers of super conducting poloidal field (PF) coils. They have been assembled and the in-accuracy in positioning of these coils is measured. The deviations in coil positions will generate error field and this will degrade the plasma performance. The error field produced by the TF coil misalignment can impact the plasma startup and it is necessary to quantify this error. These averaged toroidal field error can be measured and detected using electron beam source inside tokamak vessel. In SST-1 tokamak (major radius, R = 1.1m and minor radius a=0.2m), a low voltage electron beam source is mounted on the radial port at the mid-plane and can be moved to any point between R=0.95 - 1.35m. Cameras are mounted in radial port as well as top port to capture the deviation of the electron beam lines. Vacuum vessel is filled with helium gas which creates luminescent trace of electron because of impact excitation, creating a visual toroidal beam of electron inside vacuum vessel when the Toroidal Field coils are energized with a current. This paper present the experimental observation of beam deviation with respect to various TF currents and then, the estimation of measured error field in SST-1 tokamak. An attempt is also made to explain the electron beam deviations measured through these experiments. The deviations in R, φ and Z are incorporated in the numerical model of SST-1 TF coils for the error-field estimation. Effect of other coils on this error field would also be analyzed. Error field profiles in both R and Z direction would be quantified, which would be a useful information for the plasma operation. Key words: TF coil, Electron beam, error field Summary: Electron beam experiments along with the numerical simulations to quantify the error-field in SST-1 tokamak is presented in this article.

Speaker: Mr Someswar Dutta (Institute For Plasma Research)

FEC_2018_summary_v2.pdf

589 Evolution of locked mode under the existence of non-axisymmetric fields in KSTAR

Since 2013 KSTAR campaign, we have investigated the effect of non-axisymmetric (NA) fields on the evolution of magneto-hydrodynamic (MHD) instabilities by using the error field (EF) correction coils. Locking and EF penetration were induced by the torque imbalance between the intrinsic rotation and external magnetic braking. Further increase of the n=1 EF resulted in minor and major disruptions. As anticipated by the magnetic braking effect, the stronger n=2 NA field case exhibited earlier EF penetration and locking. On the contrary to the locking phenomena, subsequent minor and major disruptions were delayed and even avoided by the stronger n=2 NA field. Analysis of the n=1 locked mode amplitude revealed that the n=2 NA field started to hinder the growth of n=1 locked mode when the mode amplitude reached certain level in Ohmic discharges. The starting level of the hindrance appears to rely on the n=2 NA field strength. More interestingly, the fast growth was recovered just before minor disruption. Nevertheless, the pure n=1 EF case without n=2 NA field did not show clear change of the growth rate after locking and just exhibited gradual increase of the locked mode towards the minor disruption. A kinematic model of tearing-kink interaction is in qualitative agreement with the experimental observations. In neutral beam (NB) heated L-mode discharges, the overall effect of n=2 NA field appears similar to that in the Ohmic discharges. However, the detailed evolution towards major disruption was somewhat different. With n=2 NA field, initial minor disruptions were much weaker than those in the reference discharge without n=2 NA field. To reach a comparable level of minor disruptions in the reference discharge, we needed stronger n=1 EF in the discharge of n=2 NA field. Electron cyclotron emission imaging (ECEI) showed different patterns of minor disruption depending on the existence of n=2 NA field. As in the Ohmic discharge, the resulting major disruption was delayed in the NB heated L-mode discharge as well. A series of experimental results in various discharge conditions show the possibility of using NA fields to control or delay the plasma disruption process.

Speaker: Dr Jayhyun Kim (National Fusion Research Institute)

590 Exact conservative solutions of fluid models for the scrape-off layer as the ancestors of blobs?

Exact solutions have been obtained for the conservative part of a standard two-fluid (density plus vorticity) model of the scrape-off layer (SOL) which are of the travelling-wave type and describe transport of large-, machine-scale structures across the plasma cross-section (radially and/or poloidally). These conservative solutions can be of various forms and shapes, either extended or localised, moving either outwards (as actual high-density blobs) or inwards (as plasma holes with densities lower than the backrgound's), being conjectured that they are the ancestors of the propagating coherent structures, known as blobs, often seen in experiments and numerical simulations of SOL turbulence. These solutions have added value *per se*, not only because they are actual solutions of the conservative interchange model of the SOL, but also because they allow some analytical control over numerical implementations of the model as they provide benchmarks, or standards, against which the latter can be verified. In fact, and as it will be shown, they have been used to verify different numerical schemes to solve the equations of SOL turbulence, namely, an explicit 4th order Runge-Kutta and a new semi-implicit method which, contrary to the Runge-Kutta scheme, guarantees stability without the need for very fine meshes and the consequent computational cost. Once confidence has been gained regarding the numerical implementation of the model, non-conservative terms (such as diffusion, sources, and parallel losses) have been added to check what happens to the conservative structures (whether they are merely distorted or end up by disappearing).

Speaker: Prof. João P. S. Bizarro (Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, 1049-001 Lisboa, Portugal)

TH_P7-15_slide.pptx

591 Experimental observation and modelling of high-Z impurity transport by tungsten powder injection in KSTAR plasmas

In fusion plasmas with electron temperature of several keV, most of the tungsten (W) particles are in W27+ to W45+ ionic states, which emit line radiations of a few nm wavelength in the EUV range. Thus, a compact (63x44x18 cm3) advanced EUV spectrometer system (CAES) was recently developed [2] to simultaneously measure spectrally-resolved tungsten emission and spatially-resolved W density profile. Since the 2016 KSTAR campaign, a few mg of W powder of 12 μm typical size was injected to the plasma by a portable compact (60x30 mm2) gun-type particle injector [1] which can inject any kind of metal powder. During the experiments, spatiotemporally varying W spectra were successfully obtained by CAES with 2.7 cm and 67 ms of spatial and time resolutions. In conjunction with these experimental setups, a spectral model for high-Z impurity transport has been developed based on coronal approximation. The Flexible Atomic Code (FAC) is used to calculate the PEC of W10+ to W48+. The modelled line emissions are compared with the measured data in order to find proper diffusion coefficients and convection velocities from the radial continuity equation. In addition, the radiation power loss relation and the force balance equation with a centrifugal force effect are included to find the two-dimensional global density profile of high-Z impurities and a relation between the toroidal rotation speed and poloidal asymmetry. These schemes are possible by using the infrared imaging video bolometer (IRVB) diagnostics in KSTAR, through which we observed a poloidally asymmetric distribution of tungsten emission due to the centrifugal force effect in the past KSTAR campaigns. Code validations were performed by comparing with the results from SANCO [3], showing a good agreement within 10% error of the intensity of Ar15+ 35.3 nm line emission. It is also clearly seen that more spectral lines appear in the modelled structure than in the measured spectrum, which is possibly an indication that a refined description of the W atomic structure must be included in our calculation. References: [1] H. Y. Lee et al., Rev. Sci. Instrum. 85, 11D862 (2014) [2] I. Song et al., Rev. Sci. Instrum. 88, 093509 (2017) [3] J. Hong et al., Nucl. Fusion 57, 036028 (2017)

Speaker: Mr Inwoo Song (Korea Advanced Institute of Science and Technology (KAIST))

summary_slide_I.Song.pptx

592 Experimental observations of the plasma shape effect on the RMP-ELM coupling for optimization of the KSTAR ELM-crash control

Reliable and robust resonant magnetic perturbation (RMP) on the edge-localized-mode (ELM) crash control is crucial for the success of ITER and beyond. In recent KSTAR experiments, a critical dependence of RMP-ELM coupling on the plasma shape was found to be as important as much as $\mathrm{q_{95}}$. In application of the low-n RMP fields, small variations in the lower triangularity by controlled $\mathrm{R_{X,lower}}$ (radial position of lower X-point) made significant changes on RMP coupling, suggesting a narrow window for the ELM-crash suppression. For the shape effects found in 2016, such $\mathrm{R_{X}}$ window for the RMP induced ELM-crash suppression was surprisingly narrow ($\mathrm{\delta_{lower}=0.74\pm0.04}$ and $\mathrm{R_{X,lower}=144\pm2cm}$), while the other shape parameters, such as $\mathrm{Z_{X}}$, seem to have weak effects. Also it was found that the same shape valid for the n=1 RMP was not effective for the n=2 RMP induced ELM-crash suppression. In 2017, further study revealed that such a strict condition of triangularity ($\mathrm{R_{X,lower}}$) can be relaxed by allowing for an additional small up-down asymmetry on the plasma shape. Applying this new optimized plasma shape led us to make substantial improvements on reliability and robustness of the RMP induced ELM-crash control. As a result, the n=1 RMP induced ELM-crash suppression were successfully demonstrated in a wide range of $\mathrm{q_{95}}$ even with a fixed RMP spectra, achieving a record-long sustainment of ELM suppression more than ~30 sec. Similarly, the n=2 RMP-induced ELM-crash suppression was achieved with the same shape (universality) at ITER-relevant low $\mathrm{q_{95}}$=3.3~3.5. Furthermore, we found a singular response to the shape change for the RMP-plasma coupling, with a support of ideal MHD modeling.

Speaker: Dr YoungMu Jeon (National Fusion Research Institute)

2018FEC_One_page_summary_slide_ymjeon.pdf

593 First Analysis of the Updated ITPA Global H-Mode Confinement Database

We report on an ongoing task within the ITPA concerning a revision of the global H-mode energy confinement scaling in tokamaks, known as IPB98(y,2). The objectives of the task are to update the database with data closer to ITER baseline and hybrid conditions, to expand the parameter range and include new data from devices with reactor-relevant metallic walls, to explore predictor variables and possibly decouple core and pedestal scaling, and to employ advanced regression techniques with an emphasis on the robustness of the scaling. In this work, first results are presented of a description of the most recent version of the global H-mode confinement database, following addition in 2017 of new data from JET with the ITER-like wall and ASDEX Upgrade with its tungsten wall. The so-called “standard set”, based on ITER-relevant selection criteria, presently contains 5718 entries from 18 machines. Considerable reduction of the linear correlation between the predictor variables has been observed, in comparison with the database used for the IPB98 scaling. Correlation coefficients above 0.5 remain between plasma current and major radius (0.74), current and loss power (0.65), and accordingly between major radius and loss power (0.60). In pursuing the analysis of the updated database, the classic power-law dependence is assumed and regression analysis is being performed using ordinary least squares, a robust Bayesian technique and robust geodesic least squares. Examination of individual device scalings, both for low-Z and high-Z walls, has given insight into similarities and differences among these individual datasets, and this may lead to the resolution of some of the recently observed discrepancies between IPB98 and single-machine scans. A significant part of the ongoing analysis effort will concentrate on exploring hidden variables not represented in the IPB98 scaling, in light of recent insight into the physics governing energy transport in tokamaks. This might resolve issues related to collinearity of predictor variables and may eventually contribute to a multi-machine scaling that better reflects the underlying physical dependences. This would also benefit interpretation of the scaling in terms of dimensionless variables. For similar reasons, the power-law form of the scaling may need to be re-evaluated in future work.

Speaker: Dr Geert Verdoolaege (Ghent University)

Verdoolaege_EX_P7-1_summary_slide.pdf

594 Implementation of 3-D effects of the ITER plasma-facing components in a 2-D real-time model-based approach for wall heat flux control on ITER

A real-time (RT) first wall (FW) heat load control system will be required at a very early stage of ITER plasma operations. The long pulse nature of the device imposes active cooling of all plasma-facing components (PFCs) and thus strict control of surface power flux density at all times. Plasma current ramp-up in limiter configuration on the beryllium FW panels (FWP) is foreseen for all ITER discharges, with a preference for the inner wall surfaces. Limiter phase heat flux densities on the shaped FWP in the vicinity of plasma contact are expected to approach the maximum design values and hence the deposited heat flux must be monitored and carefully controlled. Development of a physics-based and control oriented model, based on real time (RT) equilibrium reconstruction for implementation into the ITER Plasma Control System has thus already begun. The model-based approach in the simplest case, describes the heat flux deposited on PFCs as a poloidal flux function with two parameters to be specified by the modeler: the power exhausted across the plasma boundary, $P_{SOL}$ and scrape-off layer (SOL) width, $\lambda_q$. A modular, flexible and expandable Matlab/Simulink architecture for the 2-D model based approach has been successfully developed, implemented, and verified with DINA scenario data on the Plasma Control System Simulation Platform (PCSSP). An additional module containing weighting factors has also been implemented in the 2-D RT model based approach to include the true 3-D geometry of the FWP. This is an essential modification if a more realistic value for the true maximum heat flux is to be correctly predicted. Integration of the 3-D effect into the algorithm is performed by offline determination of the heat load distribution on the full 3-D poloidal sector using a new utility, SMITER, developed at the ITER Organization, in which the SMARDDA field line tracing code has been embedded in a GUI interface permitting import and appropriate meshing of full CAD descriptions of the FW geometry. For each equilibrium, weighting factors associated with the position in the poloidal plane and magnitudes of the peak heat flux are extracted for implementation into the 2-D model based approach. The improved RT model is also being experimentally tested and validated on the TCV tokamak using infra-red measurements of the central column surface power flux density.

Speaker: Dr Himank Anand (ITER Organization)

Summary_slide_updated.pptx

595 Implementation of the Spherical Tokamak MEDUSA-CR: Stage 1

The low aspect ratio Spherical Tokamak (ST) MEDUSA (Madison Education Small Aspect Ratio Tokamak) is currently being re-commissioned at the Instituto Tecnológico de Costa Rica, after it was donated by the University of Wisconsin-Madison, USA. The main characteristics of this magnetic confinement device are described as follows: plasma major radius of Ro < 0.14 m, plasma minor radius a < 0.10 m, plasma vertical elongation 1.2, toroidal field at the geometric center of the vessel BT < 0.5 T, plasma current Ip < 40 kA, ne(0) < 2 x 1020 m∧-3, central electron temperature Te(0) < 140 eV, discharge duration is < 3 ms, top and bottom rail limiters, and natural divertor D- shaped ohmic plasmas [1]. Training students and researchers is the main goal as for ST MEDUSA-CR, to merge knowledge between physics and engineering in order to address relevant concepts for spherical and conventional Tokamaks [2]. Currently diverse topics are being addressed in the first engineering stage of the MEDUSA-CR. For the vacuum system design there has been developed the corresponding documentation process of the implementation and testing vacuum, also it is present a new design of the vacuum vessel made of stainless steel. The design, of the new injection system, entirely developed to accomplish the Spherical Tokamak’s requirements has been successfully tested. The electric current control of the coils presents a possible upgrade to converting ST MEDUSA-CR to AC mode. Additionally, a MHD equilibrium simulation for the original configuration of the device has been performed using a code named Fiesta; which was facilitated by Geoffrey Cunningham from Culham Centre for Fusion Energy (CCFE).[3, 4] References [1] G. D. Garstka, PhD thesis, University of Wisconsin at Madison, September 1997. [2] V.I. Vargas et al., Progress on Re-commissioning of the Spherical Tokamak MEDUSA in Costa Rica, 23rd IAEA Technical Meeting on the Research Using Small Fusion Devices (23rd TM RUSFD), March 29-31 2017,Santiago, Chile. [3] V.I. Vargas et al., Re-commissioning of the Spherical Tokamak MEDUSA in Costa Rica, 26th IAEA Fusion Energy Conference (FEC IAEA), 17–22 October 2016, Kyoto, Japan. [4] V.I. Vargas et al., First engineering stage of the Spherical Tokamak MEDUSA-CR, 16th Latin American Workshop on Plasma Physics (LAWPP), 4-8 September 2017, Mexico City, Mexico

Speaker: Prof. Jaime Mora-Meléndez (Instituto Tecnológico de Costa Rica)

Mora J - FIP - Slide.pdf

596 Implications of Uncertainties on the European DEMO design

During the pre-conceptual design phase of fusion devices such as the European demonstration fusion power plant (DEMO), systems codes provide a fast evaluation of optimal design points and highlight high impact areas. However, determining or evaluating a design point at such an early stage comes with uncertainties in many of the design parameters. These uncertainties are both associated with the physics as well as the engineering basis of the European DEMO design. This work applies an uncertainty quantification analysis to the 2017 pulsed European DEMO design using the PROCESS systems code. It assumes that DEMO will be built as suggested by the baseline and explores what implications the currently known physics and engineering uncertainties have on the expected performance parameters (net electric output and pulse length), while optimising the fusion gain Q or the pulse length. It furthermore compares the analysis of the conservative DEMO baseline design to the more advanced Flexi-DEMO option. A more detailed single parameter analysis is clearly identifying high impact parameters. This is confirming previous investigations as well as revealing new areas that warrant deeper investigation.

Speaker: Dr Hanni Lux (CCFE, UKAEA)

2018_10_FECSummarySlide_HLux.pptx

597 Integrated Modeling of Core, Edge Pedestal and Scrape-Off-Layer for High Beta_N Steady-State Scenarios on DIII-D

A new theory-based integrated modeling of Core, Edge Pedestal, and Scrape-Off-Layer (CESOL) has been developed, validated and used to project core to boundary solutions for an upgrade to DIII-D that will develop the plasma physics path to a steady state fusion reactor. It also represents a significant step towards a whole device modeling (WDM). The simulation reproduces DIII-D high N discharge measured profiles across regions from the magnetic axis to the divertor. CESOL consists of three independent, compound Integrated Plasma Simulator (IPS) workflows: IPS-FASTRAN (1-D core transport), IPS-EPED (edge pedestal), and IPS-C2 (2-D SOL plasma/neutral transport). In the core region FASTRAN computes all transport channels with TGLF and is self-consistent with an EPED edge pedestal. The total particle and energy fluxes are matched at the separatrix between the FASTRAN+EPED and C2 workflows in an iterative steady-state solution procedure. This specific coupling aims to determine the density and temperature at the separatrix, which are used to update the input to EPED and close the strong nonlinear dependency among the core, edge pedestal, and SOL regions. Projections for DIII-D upgrades indicate that fully non-inductive solutions will be able to probe critical stability, transport and energetic particle limits with reactor relevant broad current profiles (qmin>2) and N up to ~5 at low collisionality and a range of rotations. The use of ultrahigh harmonic 'helicon fast wave' or high field side LHCD extends scenarios to high density, low rotation and increased Te/Ti, reducing divertor heat flux by more than a factor of 2 with increased bootstrap current fraction, fBS~0.7. Helicon and LHCD also extend profile range, stability and N potential at low and high rotation. These techniques will be combined with new closed pumped upper and lower divertors, materials testing facilities, and 3D upgrades to develop integrated core-edge steady state solutions on DIII-D relevant to future fusion reactors. (Supported by US DOE under DE-AC05-00OR22725, DE-FC02-04ER54698, DE-AC52-07NA27344, DE-FG02-95ER54309, and DE-SC0012656.)

Speaker: Dr Richard J. Buttery (General Atomics)

TH-P7-2-onepager.ppt

598 Internal Structure of MHD Fluctuations for Various Current Density Profiles during Current Rise Phase of Ohmic Discharge in VEST

During the current rise phase of tokamak discharges, evolving current density profiles are associated with the MHD fluctuations that are often held responsible for the confinement degradation, or even disruption, early in the discharge. Moreover, VEST, (Versatile Experiment Spherical Torus) for the NBI heated advanced tokamak regime, adopts the fast current ramp up Ohmic discharge, where the study of the reversed shear q profile and the suppression of this “current rise” fluctuations is needed. Here, we present the internal structure of this fluctuations in accordance to the equilibrium current profiles during the current rise phase of VEST, using data from both the external and the internal magnetic diagnostics. The internal magnetic probe array, upgraded from the previous model, have been used to both constrain the newly developed EFIT-like equilibrium reconstruction and measure the internal magnetic fluctuation. Because VEST hosts a relatively low temperature plasma, the plasma degradation by the introduction of the internal magnetic probe array into the plasma is less than 10%. The mode number is identified by the toroidal and poloidal Mirnov coil array signals analysed by the method based on singular value decomposition. During a typical Ohmic discharge in VEST, shot #18452, the plasma current is ramped up very fast with dIp/dt<20 MA/s and a hollow current profile and a weak shear safety factor profile are formed. In the spectrogram of the outboard midplane Mirnov coil, the modes n=1 and n=2 are observed, spanning modes (2,1), (3,1) and (3,2). As the rate of plasma current rise is slowed down to dIp/dt<10 MA/s, as in shot #18390, the skin current is diffused in to form a more broad current profile and a positive shear safety factor profile. Here, the mode (2,1) is suppressed and the mode onset is delayed. We conjecture that this change in the mode structure is related to the attainment of a maximum plasma current of 100 kA in shot #18390, a 25% increase from shot #18452, which is driven with the same loop voltage. From the internal structure of the instability, it is found that the two peaks of the internal fluctuation amplitude |δBz| are localized around a relevant rational q surface in agreement with the mode structure measured by the external magnetic diagnostics.

Speaker: Mr Jeong-hun Yang (Seoul National University)

180927 highlights.pdf

599 Intrinsic Toroidal Rotation for Ohmic L-mode Plasmas in KSTAR

The toroidal rotation from pure ohmic discharges without any external momentum sources is one of the most fundamental types of self-generated intrinsic rotation for magnetic fusion researches. There have been reported a wide range of magnitudes, directions and abrupt reversals for ohmic toroidal rotation studies, no clear physical mechanisms are concluded to explain these intrinsic ohmic rotation behaviors. Although the origin of the intrinsic ohmic rotation still needs intensive studies, the long-standing question for the direction of the ohmic rotation could be speculated from precise experimental evidences measured from cross validated diagnostics since KSTAR equips two main diagnostics. The core ohmic toroidal rotation has been measured mostly in the counter-current direction with normal operation conditions and the corresponding scaling is reported from KSTAR. Recently, we expanded the ohmic rotation scaling to the co-current direction for the first time utilizing lower electron density regimes. In this presentation, we will investigate the critical clue for the ohmic rotation direction and extended scaling to the co-current direction.

Speaker: Dr Sang Gon Lee (National Fusion Research Institute)

600 Ion Inertial Effects on Three-dimensional Filament Dynamics

The ion inertial effects on the sheath-limited filament dynamics have been investigated with the three-dimensional (3D) electrostatic Particle-in-Cell (PIC) simulations. We have shown that the radial propagation speed of a sheath-limited filament becomes slightly slower in deuterium-tritium (D-T) plasmas than in light hydrogen (H) plasmas because of the gyro motion effect. The filament (blob) radial propagation speed is the fundamental and important factor for the boundary layer transport. However, the isotope effects on filament dynamics including the radial propagation speed had not been focused on in previous studies. On the other hand, our previous work showed that the minor heavy ions decelerate the blob by the formation of the dipolar density distribution of minor heavy ions in a blob due to the polarization drift. Nevertheless, according to the traditional static estimation of the sheath-limited filament transport, it is expected that the sheath effect makes the radial propagation speed in D-T plasmas faster than that in H plasmas. Thus, in this study, the ion inertial effects on the sheath-limited filament dynamics have been investigated with the 3D-PIC simulations in order to evaluate the isotope influences in the polarization drift effect and the sheath effect. The simulations have revealed that the sheath effect is canceled out by the polarization drift effect. Therefore, the radial propagation speed in D-T plasmas ought to be roughly the same as that in H plasma. However, in the simulations, it has been observed that the radial propagation speed in D-T plasmas is slightly slower than that in H plasma. This fact is thought to arise from the gyro motion effect which induces the poloidal symmetry breaking, the poloidal movement of blob, and the deceleration of radial propagation.

Speaker: Dr Hiroki Hasegawa (National Institute for Fusion Science)

Summary_Slides summary_slide_JpNIFS_hasegawa.pdf (Protected)

601 JET Upgraded Diagnostic Capabilities and Scientific Exploitation in Support of Deuterium-Tritium Operation

JET upcoming deuterium-tritium campaign, DTE2, is scheduled to take place before the end of 2020. From a point of view of diagnostics developments, for many years JET diagnostics have been upgraded in order to provide adequate support for the scientific exploitation of a D-T campaign, with particular attention to the experimental and operational conditions expected during deuterium-tritium campaigns. Diagnostic capabilities relevant for burning plasmas conditions have been specifically targeted with the focus mainly on fast ions, instabilities, neutron, gamma, ion temperature and operations support. JET diagnostic capabilities and obtained experimental results relevant for the scientific exploitation of the upcoming DT operations are discussed. This work has been carried out within the framework of the EUROfusion Consortium and has received funding from the Euratom research and training programme 2014-2018 under grant agreement No 633053. The views and opinions expressed herein do not necessarily reflect those of the European Commission.

Speaker: Dr Joao Figueiredo (EuFusionUk and PtIPFN)

Figueiredo.Joao.Summary.Slide.pptx

602 Key Considerations in the Power Extraction from Fusion Reactors

As the demand for energy grows, futuristic energy sources like the D-T thermonuclear fusion using the magnetic confinement scheme called tokamak are being researched upon. It is generally presumed that a fusion blanket surrounds the tokamak plasma which absorbs the fusion neutrons, using their energy to convert into heat energy and nuclear transmutation with lithium to re-generate the lost tritium. Since the focus of the fusion community is largely on design, construction, operation and research of fusion devices and plasma performance, the engineering study (in-depth) of how is one going to take the power out from the blankets, through the complex geometry, all the way up to the Steam Generator (SG) has hardly received any attention. It is almost assumed without any reason that ‘if we have the heat source, the rest is well known’. To some extent, this state of affairs could also be due a belief that such reactors would be realized only in the far future. This paper presents an in-depth look at the key considerations for transporting the power from the blankets to the SG. The main purpose of the study is to develop and compare conceptual designs for the above, based on engineering considerations. The problem involves three main steps: (a) transport of heat from the blanket-outlet up to the SG, (b) heat-exchange within SG and (c) return of the blanket coolant to the blanket-inlet. Three different coolants seem to have been considered currently by the fusion blanket community: Water, Helium and Lead-Lithium eutectic (PbLi). However, it appears that an additional heat-exchanger (HX) will be needed for PbLi (which is most likely to be with Helium) before the heat is transferred to SG. From this point of view, both the concepts (PbLi and He cooled) end up in requiring a design of SG based on He-water HX. Using the current available designs of fusion power plants; to some extent the layout of ITER and the consideration of SG for fission power reactors, we have developed some conceptual designs for extraction of power. A computational tool has been developed to efficiently determine the thermo-hydraulic parameters to be verified by detailed ANSYS calculations. Keywords: Fusion power plant design, heat exchanger design, efficiency of thermal cycle

Speaker: Mr Piyush Prajapati (Institute for Plasma Research)

SUMMARY SLIDE_PIYUSH_PRAJAPATI_FIP-P7-28.pdf

603 Maintenance experience of 315kW Electrical Motor of Helium screw compressor in 1.3kW Helium Refrigerator/Liquefier Plant

1.3 kW helium refrigerator/liquefier (HRL) system is installed and in operational at Cryogenic division of IPR since 2003. Steady State Super-conducting Tokomak consists of superconducting magnets which are cooled by cryogenic HRL plant. Three numbers of 315 kW asynchronous induction motors are used to drive helium screw compressors of HRL plant, therefore it is very essential to maintain the electrical motors in working condition for continuous longer tokomak experiment operation. This paper describes electrical aspect of operation, maintenance and troubleshooting experiences of electrical motors that include motor overhauling, motor winding insulation testing, no load and full load testing, online temperature monitoring and motor cooling arrangements as well as vibrations measurement of compressor, motor and the skid.

Speaker: Mr Dikens Christian (Institute for Plasma Research)

Dikens_FEC2018_Summary_slide.pdf

604 Model Development and Electromagnetic Analysis of Vertical Displacement Event for CFETR Helium Cooled Solid Blanket

As one of typical blanket concepts for Chinese Fusion Engineering Test Reactor (CFETR), a conceptual structure of helium cooled solid breeder (HCSB) blanket was designed by USTC. Considering that electromagnetic load is one of the main concerns for the blanket module, a FEM (finite element method) model of the HCSB was developed and the electromagnetic analysis of the blanket module was implemented using a finite element analysis (FEA) software called MAXWELL. For transient electromagnetic analysis with the vertical displacement event (VDE), a more accurate model where the plasma described by 69 filaments was adopted and the whole 15 blankets lying in a toroidal-poloidal section were explored. The research of the ferromagnetic effect of RAFM steel was carried out and the magnetic field, induced eddy currents, the magnetic force were computed and analyzed. The analysis results show that ferromagnetic effect broadened the range of magnetic field of the model and strengthened eddy current effects. In addition, the maximum value of the eddy current density was 71.2 MA/m2 and the maximum magnitude of the electromagnetic forces was 1409.0 kN under the ferromagnetic effect.

Speaker: Prof. Hongli Chen (University of Science and Technology of China)

605 Multi-physics modeling of the long-term evolution of plasma-exposed surfaces

We report on a new simulation capability for predicting plasma-surface interactions, including the evolution of the plasma-facing component (PFC) surface layer that is continually modified by contact with the fusion plasma. This involves a wide range of physical phenomena: our current model includes components for a) the scrape-off layer plasma including fuel ions and extrinsic impurities (using SOLPS[1]), b) transport and redeposition of eroded wall material (using the newly developed Monte Carlo code GITR), c) the implantation of plasma ions into the material and subsequent wall erosion (using F-TRIDYN, and extension of TRIDYN [2]), and d) the dynamics of the subsurface (Xolotl, a new continuum cluster dynamics code). These components are being integrated to yield predictive capability for the changes in surface morphology, fuel recycling and tritium retention, and how these are impacted by material erosion and redeposition, initially targeting tungsten exposed to mixed hydrogenic and helium plasmas. Initial simulations have focused on a recent set of experiments at the PISCES linear facility, where tungsten was exposed to helium plasmas with fluxes of 0.5-41022 /m2/s for durations of 5000-10000s, with incident energies of ~250eV controlled through biasing. Initial simulations have demonstrated the effect of including bubble bursting and sputtering on the subsurface evolution, as well as validation against erosion and migration measurements in PISCES. Integrated simulations for ITER-like parameters in a toroidal geometry will be presented. *Research supported by the US Department of Energy under DE-AC05-00OR22725 [1] W. Miller et al, Comp. Phys. Comm. 51 (1988) 355. [2] R. Schneider et al, Contrib. Plasma Phys. 46 (2006) 3.

Speaker: John Canik (Oak Ridge National Laboratory)

606 Negative ion beam source physics as a complex system: identification of main processes and key interdependence

A key component of ITER is the heating Neutral Beam Injector (NBI) system, expected to be the main source of the input power necessary to reach fusion conditions. The nominal parameters of the ITER NBI (40 A negative H-/D- ion beam accelerated to 1 MeV and then neutralized) are so challenging that they require extensive international research and development activities. Reliable operation of NBI for one hour remains an open issue: it results from several processes, mutually interacting in a non-linear way. In this contribution, complex network theory is applied to the physical processes (nodes) affecting generation, extraction and acceleration of negative ions in the simpler case of the NIO1 experiment, operating at Consorzio RFX. The number of driver nodes is 4; preferential matching identifies multiple sets of driver nodes. The most frequently identified driver nodes are interpreted as the most relevant processes: deflection of H- in the PG-EG gap depends on meniscus asymmetry, linked due to non-uniform ion flow in the plasma, as experimentally found; gas pressure in the vessel drives the compensation of the beam space charge, allowing the beam to propagate with no divergence increase. Evidence of the latter driver node spurred the investigation of the beam-generated plasma by means of a Retarding Field Energy Analyzer and numerical simulations. Two surface phenomena will be discussed in the contribution, as they are very important for the NBI operation and must be included in the complex network. H- production is enhanced by evaporating cesium over the source wall material. The arrangement of the cesium atoms is correctly simulated by molecular dynamics: the resulting imperfect film is found to be affected by moderate temperature, which allows redistribution of cesium, whereas higher temperatures disorder again the film leading to evaporation. Another key role played by surfaces regards high voltage holding, for which a novel model, based on the assumption of a dielectric layer (oxidized metal), is proposed. When the dielectric strength of the layer is exceeded, quantum mechanical computations provide the current, which acts as a trigger for breakdown.

Speaker: Dr Vanni Antoni (Consorzio RFX)

607 Non-Invasive Plasma Density Measurement in a 13.56 MHz Magnetized Capacitive Coupled RF discharge

Capacitive coupled plasmas (CCP) have unique applications in microelectronic industries, besides they are also important in plasma interaction with material surfaces, such as near field region of ICRF antenna infusion devices. Systematic studies of these plasmas are concurrently carried in laboratory plasma devices to develop models to explain the anomalous behavior of plasma sheath interactions. Plasma diagnostics plays a crucial role in providing necessary input data for the verification of these models. Recently a capacitive coupled discharge with externally imposed transverse magnetic field has been developed [1]. It has been found that the external magnetic field greatly modifies the discharge characteristics, by introducing ExB drifts adjacent to the discharge plates. Direct measurement of plasma parameters in CCP discharge is primarily difficult due to very large amplitude oscillation in plasma potential. To certain extent, a triple probe is convenient as it is routinely used in the strongly magnetized edge plasma region in tokamaks. However its application in radio-frequency plasmas needs careful design of electrical feed-through and measurement of voltage/ currents using external circuits. An alternative method to determine the average density of the plasma can be achieved by looking at the impedance characteristics of the discharge. The discharge impedance is the measure for the plasma conductivity, which intern determines the plasma density. Recently electrical circuit analysis has been applied to estimate the collisionality in magnetized CCP discharge. In this paper, we show that the plasma density can also be determined using this technique. The obtained results have been compared with a triple Langmuir probe and the results are shown to be in good qualitative agreement.

Speaker: Ms shikha Binwal (Jamia Millia Islamia (A Central University))

608 Observation of Heat Load on the Castellated Tungsten Block by Back-Scattered Particles from Intentionally Misaligned Protruding Edge

KSTAR has been involved in studying leading edge heat loads since 2014 by using series of multi-purpose, brazed W blocks (W-Cu-CuCrZr). They are mounted and assembled into two adjacent, inertially cooled graphite tiles installed in the outer divertor target region of KSTAR, within the field of view of an infra-red (IR) thermography system installed in an upper lateral port and to which special modifications have been made for this study to increase the spatial resolution to ~0.4 mm/pixel on the block surface. The blocks are arranged in different groups, with toroidal gaps of 0.5 mm addressing a specific issue: a variety of leading edge heights (0.3, 0.6, 1.0, and 2.0 mm), from the ITER worst case to heights even beyond the extreme value tested on JET. Adjustment of the outer divertor strike point position is used to deposit power on the different blocks in different discharges, but with emphasis in these first studies on studying power loading as a function of leading edge height. The measured power flux density on flat regions of the surrounding graphite tiles is used to obtain the parallel power flux, q|| impinging on the various W blocks. Experiments have been performed in L-mode and Type I ELMing H-mode, but owing to the low power flux densities in L-mode, the inter-ELM H-mode exposures provide the best IR data. Discharges are run at Ip = 600 kA, BT = 2 T, PNBI = 3.5 MW, leading to a hot attached divertor with typical pulse lengths of ~10 s and total field line incidence angles of 2-3 at the strike point (cf. 2.5 on ITER). During the experiment, an interesting feature was observed: there was clear evidence of heat load on the castellated tungsten block by back-scattered particles from intentionally misaligned protruding edge. The line profiles show three different peaks corresponding to: one from the protruding edge, two others from the edge and surface of block in front of the protruding one. The deconvoluted heat flux profile and corresponding intensity ratio of each peak show that up to 46 % of IR intensity was originated from the block in front of the protruding one: around 44 % from the edge and 2 % from the surface. The peak intensity of back scattered profile depends strongly on the strike point location, which indicates the contribution of energetic ions during ELM.

Speaker: Dr Suk-Ho Hong (National Fusion Research Institute)

609 Operational Results and Troubleshooting in Current Feeder System for SST-1

Current Feeder System (CFS) plays vital role in Superconducting (SC) fusion device, SST-1 (Steady state superconducting Tokamak). As, long pulse operation of the Tokamak and fusion reactors require high magnetic field to confine and shape the plasma, which is fulfilled through the superconducting magnets operating at high current ratings. CFS serves as an interface between the power supply bus bars exposed at room temperature and SC magnets at 4.5 K temperature. This complex system has been designed to energize all the superconducting coils namely toroidal field (TF) and poloidal field (PF) of SST-1 maximum up to 10 kA rated current. An optimal design of its sub-systems may significantly reduce the operational cryogenic cost in long term steady state operation of these coils. Further, reliable operations of Vapor Cooled Current Leads (VCCLs), 80 K thermal radiation shield systems, SC (Nb-Ti/Cu) bus bar feeders, high vacuum systems and associated cryogenic circuits etc. contribute towards successful and stable operations of CFS during the SST-1 plasma experiments. However, it has performed to excite the total 16 number of TF coils for longer duration in the total twenty-one campaigns so far. The operational performances in terms of cryogenic stability, current carrying capability have been validated in the excitation mode under long duration of steady state as well as in transient states such as current ramp up, ramp down and quench. This paper highlights the recent operational results with major milestone achieved as well as troubleshooting experiences since its successful commissioning in 2012.

Speaker: Mr Atul Garg (Institute for Plasma Research)

Atul_Summary - 26Sep18.pdf

610 Optimising the ITER 15MA DT Baseline Scenario by Exploiting a Self-Consistent Free-Boundary Core-edge-SOL Workflow in IMAS

The ability to describe the essential physics and technology elements needed to robustly simulate the operation of ITER is critical to being able to model the plasma scenarios that will run in ITER. The Integrated Modelling & Analysis Suite (IMAS) is used to simulate the 15 MA DT baseline scenario operation, including a description of the plasma evolution from its core up to the plasma facing components respecting the principal engineering limitations of the poloidal field coil system. The free boundary equilibrium code DINA has been combined with the JINTRAC suite of codes exploiting their full core+edge+SOL+MHD modelling capabilities in an IMAS workflow in open loop coupling. For the first time, the 15 MA / 5.3 T DT ITER baseline scenario has been assessed for the entire evolution from the early ramp-up phase (from X-point formation) until the late ramp-down phase (X-point to limiter transition) by means of integrated simulations with consideration of core+edge+SOL transport model assumptions recently validated at JET with time-dependent free boundary plasma geometry and with the pedestal pressure being determined by continuous self-consistent edge MHD stability analysis. The paper will describe the new IMAS modelling workflow for the fast execution of highly integrated DINA+JINTRAC simulations as well as the results of the ITER 15 MA DT baseline scenario optimisation study. Conclusions will be drawn regarding the available operational space and control capabilities as well as observed differences with respect to results obtained in previous modelling studies with less sophisticated workflows and a reduced level of integration.

Speaker: Dr Florian Koechl (UKAEA)

611 Overview of Recent Gyrotron R&D towards DEMO within EUROfusion Work Package Heating and Current Drive

Within the Work Package Heating and Current Drive (WPHCD), coordinated by the Power Plant Physics and Technology Department of EUROfusion, detailed studies are ongoing, which cover three different systems for plasma heating and current drive. These are, namely, systems using electron cyclotron waves, ion cyclotron waves, and neutral beam injection. The studies are in line with the European Fusion Roadmap towards a demonstration power plant (DEMO). The work breakdown structure of WPHCD, launched in 2014, includes branches dedicated to the conceptual design of the electron cyclotron system, as well to R&D focused mainly on the microwave source, the gyrotron. Gyrotron R&D is a necessary step to bridge the gap between today’s state-of-the-art gyrotrons and future gyrotrons for DEMO. Significant challenges are posed by the need for dual frequency (170/204 GHz) operation and/or frequency step-tunability of gyrotrons at a 2-MW power level, as well as by the requirements for significantly higher efficiency (> 60 %) and level of Reliability-Availability-Maintainability-Inspectability (RAMI). Gyrotron R&D within WPHCD is addressing those challenges by exploring innovative, promising approaches. In addition, and in order to keep the R&D relevant with respect to possible baseline changes and to alternative reactor configurations towards a future power plant, efficient MW-class gyrotron operation at higher (~240 GHz) frequencies is also investigated. This paper gives an overview of the recent progress of gyrotron R&D within WPHCD, driven by the aforementioned challenges and conducted along the following lines: (i) Experimental verification of coaxial gyrotron technology at longer pulses and design of a 2 MW 170/204/(238) GHz coaxial gyrotron, (ii) investigations on multi-stage depressed collector concepts to increase the overall gyrotron efficiency, (iii) development of large broadband diamond windows to allow for frequency step-tunability in steps of 2-3 GHz over a range of ~20 GHz, and (iv) advances on performance and reliability of gyrotron components to increase the RAMI level. Instrumental to the gyrotron R&D is the new Fusion Long Pulse Gyrotron Lab (FULGOR) at Karlsruhe Institute of Technology, a test stand able to support the development of continuous wave gyrotrons with a power of up to 4 MW at frequencies up to 240 GHz.

Speaker: Gerd Gantenbein (Karlsruhe Institute of Technology)

612 Performance assessment of tightly-baffled long-leg divertor geometries in the ARC reactor concept

A means to handle the extreme power exhaust from tokamak-based fusion power reactors remains to be demonstrated. Advanced divertor configurations have been proposed as potential solutions, including double-nulls, long-legs and magnetic field flaring with secondary X-points. Modelling of tightly-baffled, long-leg divertor geometries in the divertor test tokamak concept ADX has shown the potential to access passively stable, fully detached divertor regimes over a broad range of parameters [1]. The question remains as to how these advanced divertor configurations may perform in a reactor setting. To explore this, we have performed numerical simulations of these configurations in the context of the ARC reactor concept [2]. The ARC design has been recently updated to include a tightly-baffled, long-leg divertor with an X-point target [3]. ARC provides an appropriate reactor test scenario for advanced divertor configurations, with a projected SOL heat flux width of 0.4 mm and total power exhaust requirement of 105 MW. Using the divertor geometry and magnetic equilibrium from the updated ARC design, simulations of the ARC edge plasma and divertor are carried out with UEDGE [4]. The anticipated radial plasma profiles at the outer midplane are specified and power exhaust from the core is scanned over a wide range. Anomalous radial transport in the scrape off layer and divertor legs is modelled by a combination of radial diffusion and advection consistent with experimental observations, which also provide guidance for power sharing between the inner and outer divertor legs. Initial studies employing a Super-X Divertor configuration and 0.5% fixed-fraction neon impurity radiation have shown that a stable detached divertor regime exists for power exhaust in the range of 80 to 108 MW [5]. Simulations are presently being extended to study the performance of the X-point target geometry in ARC and to explore the sensitivity of the solutions to modelling assumptions and input parameters. The latest results from these studies will also be presented. [1] M.V. Umansky et al., Phys. Plasmas 24 (2017) 056112; [2] B. Sorbom et al., Fusion Eng. and Design 100 (2015) 378; [3] A.Q. Kuang et al., 59th Annual Meeting of the APS DPP, C04.6, pp66 (2017); [4] T.D. Rognlien et al., J. Nuc. Mat. 196 (1992) 347; [5] M. Wigram et al., PET 2017 conference, submitted to CtPP.

Speaker: Mr Michael Wigram (University of York)

Summary slide - TH_P7-20.pdf

613 Plasma transport in toroidally discontinuous limiter generated 3D SOL configurations of Aditya tokamak

The coupled plasma-neutral transport characteristics in the Scrape-Off Layer (SOL) produced by toroidally discontinuous limiter are essentially 3-dimensional and show strong deviation from the usual uniform SOL approximations. In a recently performed second-phase of EMC3-EIRENE plasma transport simulations for the limiter generated SOL of both original Aditya and Aditya Upgrade configurations, a number of aspects related to 3D effects in SOL are addressed. The simulated flux balance for the update relevant block-limiter case indicates that with a reduced total recycling flux for equivalent edge plasma conditions, and with the reduction in chamber wall directed cross field particle fluxes, a wider regime of relatively stable plasma conditions might be accessible for the block-limiter configuration. Although a recycling source localized on the limiter surface is used in the present simulations for the simplicity, the mechanism of main chamber recycling process is essentially captured by the present 3D study where the ionization can be significantly higher in the closed field line sections of the SOL having both higher plasma and neutral density at the downstream toroidal locations. This combination of locally enhanced ionization and longer connection lengths is seen responsible for a radially growing perpendicular flux and convex radial density profiles. This effect, found to be dominant in the original ring-limiter configuration, is however seen to yield usual concave radial density profiles in the block-limiter case, indicating that for equivalent wall conditions, the localized wall recycling can be expected less intense in the block-limiter case. In studies on ALCATOR-C-MOD this effects in a 2D divertor SOL setup was observed leading to an enhanced recycling in main chamber and indicated the possibility of an alternate density limit, capable of restricting essential reactor relevant studies in a moderate size device. The present study captures the effect in toroidally discontinuous limiter generated 3D SOL of Aditya tokamak and highlights the capacity of the 3D EMC3-EIRENE simulation to analyze it in the large scale reactor relevant conditions.

Speaker: Mr Bibhu Prasad Sahoo (Institute for Plasma Research)

B_P_Sahoo_Summary_Fec.pdf

614 Poloidal Flows, Asymmetries and Multiscale Organisation in Interplaying Core–edge–SOL Turbulent Plasmas

A central challenge in the years to come is to start providing a unified view of magnetised plasma turbulence in regimes of experimental relevance –with near-critical parameters and flux-driven self-organisation– when multiple scales and disparate regions of the plasma self-consistently interplay.

We here present a comprehensive discussion of turbulence properties when confined core, edge and Scrape-Off-Layer (SOL) regions interplay, based on well-diagnosed ToreSupra discharges and flux-driven gyrokinetic computations recently extended to modelling the outer edge and SOL regions where commonly assumed separations of scales tend to break down. Various regimes of electrostatic turbulence: Ion Temperature Gradient (ITG) and Trapped Electron Mode (TEM) are investigated in near-critical flux-driven regimes. Advanced statistical properties of transport, rotation and poloidal asymmetries are analysed and detailed confrontation with high-precision reflectometry is presented, through the use of dedicated synthetic diagnostics.

Speaker: Dr David Zarzoso

615 Power Coupling of Lower Hybrid Fast Wave in VEST

An efficient heating and current drive in the central or off-axis region of tokamak plasma should be developed for the steady state operation of a tokamak fusion reactor. A fast wave within lower hybrid resonance frequency range(LHFW) could be a scheme for the current drive in a high-density, high-temperature reactor grade plasmas.[1,2] A proof-of-principle experiment was planned for the LHFW H&CD concept in VEST[3], and a LHFW RF system has been successfully developed and installed in VEST through collaboration between KAERI, KWU, SNU, and KAPRA.[4,5] The klystron RF power is 10 kW with center frequency of 500 MHz and bandwidth of 20 MHz. The N|| spectrum of the comb-line type traveling wave antenna ranges 3 to 5 corresponding to the operating frequency. Recently, RF commissioning was started and 10 kW RF power was transmitted to the comb-line antenna in the vacuum after intensive RF vacuum conditioning. About 3.5 kW RF power was transmitted to antenna with plasma and 50~60% of input power was coupled to the plasma. The target plasma was generated with Ohmic power of about 60 kW. The peak plasma current was about 30 kA and the edge electron density varies from LHSW to LHFW launching density with the current evolution. The coupled RF power abruptly increased with the launching densities of LHWs. The driven plasma current by LHFW seems to be less than 1 kA compared to pure Ohmic plasmas. The reproducibility and higher power experiments are progressing. The low driven current may be because that the plasma density window in front of antenna for LHFW propagation into core region is very narrow due to the low toroidal magnetic field of 0.1T. In addition, the electron temperature and RF power is not as high as for efficient current drive of LHFW. More progressing and detailed experimental results will be presented with analysis based on theory and numerical simulation in the conference. ---------- [1] S.H.Kim et al., Fusion Engineering and Design, 109-111, 707-711 (2016). [2] S.H.Kim et al., EPJ Web of Conferences, 157, 03023 (2017). [3] K.J.Chung et al., Plasma Science and Technology, 15, 244 (2013). [4] S.H.Kim et al., 2017 International Spherical Tokamak Workshop (2017). [5] H.W.Lee et al., Fusion Engineering and Design, submitted (2017).

Speaker: Dr Sun-Ho Kim (Korea Atomic Energy Research Institute, Daejeon, Korea)

616 Pressure balance in a low collisionality tokamak scrape-off layer

Understanding the physics governing the scrape-off layer is necessary in order to reliably predict machine and operation critical quantities, such as the heat flux width at the divertor, plasma-wall interaction, material migration, effect of divertor condition on the pedestal profile, etc. Among the most basic quantities to predict is how the density and temperature in the SOL change from an upstream location to the divertor target. Recent simulation results [1,2] using the axisymmetric gyrokinetic code XGCa showed several noteworthy features for a low-collisionality discharge of the DIII-D tokamak. Comparisons of the electron pressure variation in the divertor region between simulation and experiment showed good agreement [1] (measurements were made with the divertor Thomson system). However, the simplified fluid form for total parallel momentum was not conserved in the near-SOL [2], which implies kinetic effects are needed to properly predict the total pressure variation in the near-SOL. Taking care to include neutral friction and viscosity resulting from a Chew-Goldberger-Low (CGL) form of the pressure tensor (i.e. only the dominant diagonal terms) does not resolve the imbalance. Here additional pressure tensor terms are added to the momentum equation, to determine their effect in the momentum balance in the scrape-off layer. This is similar to “pressure tensor unfolding”[3], but utilizing the full distribution function from XGCa to calculate the presumably higher order terms of the pressure tensor. We find that certain off-diagonal ion pressure tensor terms indeed have a non-negligible parallel variation, suggesting the need to include them in the full fluid parallel momentum balance equation. Further simulations with higher ion collisionality are explored to study the effect of ion collisionality versus proximity to the separatrix on the momentum equation in the SOL. [1] R.M. Churchill, J.M. Canik, C.S. Chang, R. Hager, A.W. Leonard, R. Maingi, R. Nazikian, D.P. Stotler, Nucl. Mater. Energy 12 (2017) 978–983. [2] R.M. Churchill, J.M. Canik, C.S. Chang, R. Hager, A.W. Leonard, R. Maingi, R. Nazikian, D.P. Stotler, Nucl. Fusion 57 (2017) 46029. [3] A.V. Chankin, P.C. Stangeby, Nucl. Fusion 46 (2006) 975–993. This work supported by the US Department of Energy under DE-AC02-09CH11466, DE-AC05-00OR22725, and DE-FC02-04ER54698

Speaker: Mr Randy Churchill (Princeton Plasma Physics Laboratory)

iaea2018_v3.pdf

617 Preventive measures to avoid electrical arcing incidences in SST-1 PF current leads

Steady-State Superconducting Tokamak-1 (SST-1) has 16 Toroidal field (TF) and 9 superconducting poloidal field (PF) coils rated for 10 kA DC. TF coils are connected in series and operated in DC condition, whereas PF coils are operated independently in pulse mode. SST-1 current feeder system (CFS) houses 9 pairs of PF superconducting current leads and 1 pair of TF superconducting current leads. The SST-1 CFS had observed arcing incidences during OT discharge in past SST-1 campaigns. Similar arcing incidences have also been observed in other tokamaks devices also like KSTAR, W7X, and EAST. The conditions which led to the electrical arcing in SST-1 CFS, thereby resulting in severe damages to PF current leads and helium Hydraulic lines will be presented in this paper. As an important preventive measure to avoid such arcing at PF current leads during SST-1 operation, insulation strengthening processes of the PF current leads have been initiated to increase the voltage withstand capability of the PF current leads. In the view of same, development of an insulation scheme using combination of polyimide and GFRP along with DGEBA epoxy resin and its validation at lab scale has been carried out. It involves study of chemical kinetics of resin towards curing cycle, electrical and mechanical characterizations of insulation samples at room temperature as well as at LN2 temperature. A breakdown voltage of > 25 kV DC has been successfully achieved with ~1.2 mm of insulation thickness at lab scale insulation samples. In order to validate the proposed insulation system under specified Helium Paschen conditions, a lab scale setup considering SST-1 operational requirements has been developed. The operation, salient features of test setup and results will also be presented in this paper. The progressive development of insulation system and validation from prototype scale to half -dummy current lead scale and thereafter implementation on actual PF current leads will also be presented in this paper.

Speaker: Ms Swati Roy (Institute for Plasma Research, Gandhinagar)

Summary FIP_P7-26.pptx

618 Progress in Design and Fabrication of Current and Helium Feeding System for JT-60SA Superconducting Coils

To realize JT-60SA of the largest superconducting tokamak device in the world, the current feeder and helium pipes have been designed so as to have the flexible structure with bend and to be supported with octagonal shape. The control system for feeding current and helium has been also developed to operate 18 Toroidal coils, 6 Equilibrium Coils and a Central solenoid. The engineering solutions developed for JT-60SA can be adopted for future fusion devices. This paper reports the progress in the design and fabrication of the current and helium feeding system to be used in JT-60SA.

Speaker: Mr Kaname Kizu (National Institutes for Quantum and Radiological Science and Technology)

SummarySlide_FIPP7-35.pptx

619 Progress in design of DEMO-FNS hybrid facility

Further development of a fusion-fission hybrid facility based on superconducting tokamak DEMO-FNS continues in Russia for integrated commissioning of steady-state and nuclear fusion technologies at the power level up to 40 MW fusion and 400 MW fission reactions. This facility is considered as the main source of technological and nuclear science information in National program for development of controlled fusion and plasma technologies till 2035 that is being currently developed and submitted to the authorities for approval. The facility DEMO-FNS exploits a conventional tokamak (CT) with major radius R=3.2 m, minor radius a=1.0 m, elongation 2.7, triangularity 0.5. The design is aimed at reaching steady state operation of the plant with the neutron wall loading of ~ 0.2 MW/m2, the lifetime neutron fluence of ~ 2 MWa/m2, with the surface area of the active cores and tritium breeding blanket ~ 100 m2. This report summarizes works performed in 2017-2018.The design goals of 2017 were concentrated on development of new simulation tools and plasma scenario, improving characteristics of enabling systems, implementing upgraded and new systems like first wall, divertor, active core, tritium breeding blanket, NBI, fueling and pumping, heat transfer, remote handling in the integrated device design. NBI system with 6 injectors, 5 of which operate in 2 hour-cycle with sequential recuperation and one can be used for repair and maintenance procedures. Total power of 500 keV deuterium beams is 36 MW. Optimization of beam transport ducts allowed reduction of their cross section to 0.4x0.8 m2. Core plasma modeling showed that neutron yield is maximal if the tritium/deuterium density ratio is 1.5-2.3. For active core with keff = 0. 95 (hybrid plant case) the neutron damage of FW-materials in dpa is comparable for fusion and fission neutron sources. Advantages of supercritical CO2 as a coolant for active cores, TBB, FW and divertor were evaluated. This coolant is attractive due to acceptable pressure (~75 bars) and temperature (up to ~500 C) ranges, low activation level in neutron environment, saving the hard neutron spectra, and compatibility with lithium technologies better than water coolant. Selection of prospective concepts is being made for hybrid fuel cycle and blankets capable to support development of Nuclear Power in RF with thermal and fast nuclear reactors.

Speaker: Yuri Shpanskiy (NRC "Kurchatov Institute")

Shpanskiy-preprint_BK2.pdf

SS_ShpanskyFEC27a.pdf

620 Progresses at CEA on EU DEMO reactor cryomagnetic system design activities and associated R&D

The EU DEMO reactor is expected to be among the first applications of fusion for electricity generation in the near future and the design of its magnet system is of central importance as driving power plant performance, budget and production efficiency. In this purpose activities were led by CEA in the framework of EUROfusion to contribute to the EU DEMO magnet system design. It encompassed design activities (dimensioning and development of associated modelling tools) with R&D (design and tests of mock-ups). The CEA design activity was mainly oriented towards Toroidal Field (TF) coils system to propose a conceptual option (pancake-wound, no radial plates) established with a semi-analytical CEA tool that considers the inter-dependent electromagnetic and mechanical behaviors. Then the proposed design is consolidated by detailed analyses: - Thermo-hydraulics evaluation by coupling THEA, TRAPS and CAST3M softwares respectively for thermo-hydraulics, electromagnetic and thermal items. The outcomes obtained in normal and off-normal regimes are exposed and discussed in the paper. - Mechanics evaluation with the most stressed zones identified and their criticity evaluated, in particular in the insulation zones. Design optimization is conducted on jacket corner radii and shape of the TF structures (casing and OIS). Finally analyses are led on the thermo-mechanic hotspot criterion. Further to the TF system, the Poloidal Field (PF) coils and the Central Solenoid (CS) design were addressed by the same methodology, the outcomes will be expose and discussed. Besides design activities, TF is also studied through manufacturing considerations with organization of the winding stations manufacturing. The DEMO cryoplant design was also addressed considering the loads to be absorbed and its process structure. The CEA proposal and the factors of merit considered will be presented and discussed. On another side, CEA also conducted R&D activities, mostly regarding the TF system with: - Hydraulic tests at variable void fraction to explore its impact on helium friction. - A full-scale TF conductor sample design and manufacture. The activity also included non-destructive examinations by tomography. Finally perspectives will be discussed regarding dimensioning with tools developed at CEA and the R&D activities to be extended.

Speaker: Dr Louis ZANI (CEA-IRFM)

621 Pump Characterization of 80 K Liquid Nitrogen Booster System for SST-1

The Steady state superconducting Tokamak (SST-1) is medium size tokamak, which requires liquid nitrogen (LN2) cooled 80 K bubble shields for reducing direct static heat load from room temperature to superconducting magnets system (SCMS). Dedicated liquid nitrogen booster system has been installed and commissioned to cater 0.7 MPa / 80 K single phase flow for uniform temperature distribution among all the 80 K shields of the SST-1 machine. The boosting system has been driven by three centrifugal cold pumps at liquid nitrogen services. These pumps have been tested at steady state mode around 0.5 MPa / 80 K at the suction and 0.7 MPa / 80 K at discharge. This Pumps can handle the pressure head in the range of 1.3 - 3.5 bar (a) at the rated speed of 5500-7000 rpm respectively, over cryogenic stability. Each of three pumps was characterized at their rated speed by evaluating various differential pressure and mass flow rate. The active current, apparent current and the actual voltages have been measured onset from the frequency controller. Based on these measurements, the efficiency of each pump have been deduced using the rated parameters and the efficiencies were obtained to be in the range of 32 - 45%, which is found to be at satisfactory level as guaranteed.

Speaker: Mr Gaurang Mahesuria (Ipr)

Summary_FEC.pdf

622 R&D for reliable disruption mitigation in ITER

The disruption mitigation system (DMS) is a key plant system to ensure the reliable and successful operation of ITER from the first experimental campaign onwards. The DMS baseline concept and design is based on present knowledge on disruption mitigation, which, nevertheless, remains subject to significant gaps in understanding, especially as concerns runaway electron (RE) formation and mitigation. This paper outlines the challenges of implementing a highly reliable DMS for ITER, presents recent progress towards the consolidation of the baseline system and develops a strategy and plan for achieving the required level of disruption mitigation to satisfy ITER’s operational needs. The baseline DMS is based on shattered pellet injection (SPI) technology. This technology delivers the material to the tokamak vessel by accelerating large cryogenic pellets that are broken into smaller fragments at the end of the delivery tube. A total of 25 pellets of different sizes can be injected to mitigate the thermal and electro-magnetic loads while preventing the formation of runaway electrons. Additionally, as a second layer of defense, the DMS is supposed to provide sufficiently fast energy dissipation should a runaway beam form accidentally. The most important challenge for disruption mitigation in ITER will be to ensure that runaway electron formation is excluded during the mitigation action up to the nominal plasma current. Designing a DMS that fulfils this essential requirement requires much better understanding of the generation of runaway electron seed populations during the MHD driven thermal quench. Another constraint is the need to ensure that the line radiation is homogenous enough to prevent first wall melting during the mitigated thermal quench. The required R&D work on the technology side comprises the integration of the baseline DMS into the ITER physical environment, the optimization of the pellet injection and shattering processes with special focus on the fragment ablation and penetration process and the optimum fragment size distribution, the assessment of the requirements for material injection for optimized effectiveness and operability in the ITER environment and the plasma parameter range. The latter will have a strong focus on the efficiency of multiple pellet injection and their relative timing and jitter.

Speaker: Dr Michael Lehnen (ITER Organization)

IAEA_2018_ITER_DMS_RD_summary_slide.pptx

623 Recent progress in developing Gamma Spectrometer in ITER

Gamma-spectrometry is used at many nowadays tokamaks due to its ability to provide unique data on fast ions and runaway electrons in hot plasma [1]. Current report dedicated to the Gamma Ray Spectrometer that will operate as a part of the ITER Neutral Particles Analyzer complex – one of the leading diagnostic systems in development progress. Conceptual and Preliminary projects were approved after reviewing; preparation of detailed documentation with justifications of solutions for associated challenges – agenda for current works. Earlier development stages were regularly reported, particularly at IAEA FECs 2010-2016 [2]. Current phase of the works included components mockups manufacturing and various tests. Firstly it was studied radiation resistance using fast neutrons from ^9Be(d, ngamma)^1^0B reaction induced on SPBPu cyclotron beam. Study demonstrated high performance of the diagnostic Port Cell components during and after irradiation with the fluence of 1.1⋅10^1^3 cm^-^2, that corresponds to the whole lifetime of the system on ITER. Another successfully completed task – development and tests of the approaches for transmitting signals and power lines to the Diagnostic Building – reliable system operation while using long (100 m) cables. Connection schemes were tested together with newly developed DAQ solutions capable in proceeding with 400 s acquisition without data losses. New fast/realtime streaming, preprocessing and compression codes tried proved reliable collection and storage of events lists and raw data, particularly while using DAQ hardware from ITER catalog. Preliminary studies of processing parameters optimization for high count rate modes typical for active ITER scenarios were carried out as well. Finally, updated MCNP models simulated to reveal possible deviation of the signal and background levels due to the alterations in design and estimated worst case defects in the radiation protection. The views and opinions expressed herein do not necessarily reflect those of the ITER Organization. This work was supported in part by the RF State Contract No. N.4a.241.9B.17.1001. In MCNP calculations MCAM software was used. 1. Kiptily, V.G., et al. Plasma Physics and Controlled Fusion, 2006. 48(8): p. R59-R82. 2. Gin, D., et al. in 26th Fusion Energy Conference. 2016. Kyoto, Japan.

Speaker: Dr Dmitry Gin (RuIoffe)

FEC2018_GinDB_SummarySlide_01.pdf

FEC2018_GinDB_SummarySlide_01.pptx

624 Robust Burn Control in ITER Under Deuterium-Tritium Concentration Variations in the Fueling Lines

Tight regulation of the burn condition in ITER has been proven possible even under time-dependent variations in the fuel concentration by the use of robustification techniques. One of the most fundamental control problems arising in ITER and future burning-plasma tokamaks is the regulation of the plasma temperature and density to produce a determined amount of fusion power while avoiding possible thermal instabilities. Such problem, known as burn control, will require the development of controllers that integrate all the available actuators in the tokamak. Moreover, the complex dynamics of the burning plasma and the uncertain nature of some of its magnitudes suggest that nonlinear, robust burn controllers will be necessary. Available actuators in the burn control problem are auxiliary power modulation, fueling rate modulation, and impurity injection. Also, recent experiments in the DIII-D tokamak have shown that in-vessel coil-current modulation can be used for burn control purposes. The in-vessel coils generate non-axisymmetric magnetic fields that have the capability to decrease the plasma-energy confinement time, which allows for regulating the plasma energy during positive energy perturbations. In this work, in-vessel coil-current modulation is included in the control scheme, and it is used in conjunction with the other previously mentioned actuators to design a nonlinear burn controller which is robust to variations in the deuterium-tritium concentration of the fueling lines. Furthermore, fueling rate modulation is not only used to control the plasma density, but also to control the plasma energy if necessary by means of isotopic fuel tailoring. Isotopic fuel tailoring is a particular way of fueling the burning plasma which allows for reducing the fusion power produced and, therefore, also gives the opportunity to decrease the plasma energy when needed. The model-based nonlinear controller is synthesized from a zero-dimensional model of the burning-plasma dynamics. A nonlinear simulation study is used to illustrate the successful controller performance in an ITER-like scenario in which unknown variations of the deuterium-tritium concentration of the fueling lines are emulated.

Speaker: Prof. Eugenio Schuster (Lehigh University)

IAEA18_Pajares_RobustBurnContro_Summary.pdf

625 Self-consistent modelling of a liquid metal pool-type divertor

The steady-state power exhaust problem in future fusion reactors (e.g, DEMO) is considered as a major challenge along the path towards fusion electricity. Dedicated work packages are being devoted to this problem within EUROfusion and a dedicated facility (the Italian Divertor Tokamak Test – IDTT) is being designed in Italy. Among the possible solutions for this problem, a liquid metal (LM) divertor has been proposed. The particularly attractive feature of this solution is the absence of damage to the wall, even in the case of high heat fluxes, thanks to the high latent heat of evaporation and to the liquid nature of the wall, which can be constantly replenished. In this work a closed, LM divertor with pool-type configuration is proposed for a reference single-null (SN) scenario, for both the EU DEMO and the IDTT. The assessment of the divertor performance is achieved by means of a newly developed model which self-consistently accounts for the most relevant physics, including plasma-vapor interactions. Self-consistency is achieved by coupling three modules: a 0D thermodynamic module for the LM/vapor system -benchmarked against 2D CFD calculations performed in OpenFOAM-, a 1D module for the SOL plasma and a 2D FEM module for the divertor walls. The resulting model is applied to the comparison between Li and Sn as possible LM choices, in terms of mitigation of the parallel heat flux to the target and of contamination of the main/core plasma. An assessment of the representativity of the IDTT in view of the EU DEMO in terms of the performance of a closed box divertor using Li is finally performed.

Speaker: roberto zanino (dipartimento energia, politecnico di torino)

Summary_slide_Zanino_IAEA_FEC_2018.pptx

626 Simulation of Beryllium Erosion and Surface Damage Under ITER-like Transient Plasma Heat Loads

The first wall panels of the ITER main chamber will be completely armored with beryllium. The primary reasons for the selection of beryllium as an armor material for the ITER first wall are its low Z, high oxygen gettering characteristics and also high thermal conductivity. During plasma operation in the ITER, beryllium besides low cyclic heat loads (normal events) will be suffered by high transient heat loads, such as ELMs, disruptions, VDE, etc. (off normal events). These transient loads cause rapid heating of beryllium surface and can result in significant changes in surface and near-surface regions, such as material loss, melting, cracking, evaporation and formation of beryllium dust as well as hydrogen isotopes retention both in the armor and in the dust. It is expected that the erosion of beryllium under transient plasma loads such as ELMs and disruptions will have significant impact on lifetime of the ITER first wall. This paper presents the main results of numerous experiments carried out during some last years at QSPA-Be facility in Bochvar Institute. QSPA-Be facility represents a single-stage coaxial quasi-stationary plasma accelerator with its own magnetic field. It is capable to provide plasma (hydrogen or deuterium) and radiation heat loads on target surface relevant to ITER ELMs and mitigated disruptions. Special Be and Be/CuCrZr mock-ups were tested by hydrogen/deuterium plasma streams (5 cm in diameter) with pulse duration of 0.5 ms in a heat loads range of 0.2-2.2 MJ/m2 and maximum quantities of plasma pulses up to 100-250 shots. The angle between plasma stream direction and mock-ups surface was 30о. During the experiments, the mock-ups temperature has been maintained in the range of RT-500°C. Two beryllium ITER grades: TGP-56FW (RF, Bochvar Institute) and S-65C (USA, Materion Brush) were studied in these experiments. Influences of plasma heat loads, surface temperature and quantities of plasma pulses on the Be erosion and surface damage are presented. The experimental data obtained are used for validation of appropriate numerical models and for the estimation of lifetime of the Be armor.

Speaker: Dr Igor Kupriyanov (A.A. Bochvar High Technology Research Institute of Inorganic Materials (JSC "VNIINM"))

Summary slide.pptx

627 Simulation of cross-separatrix edge plasma transport with the continuum gyrokinetic code COGENT

Axisymmetric (4D) simulations using the finite-volume code COGENT are performed to explore the role of ion kinetic effects in tokamak edge plasmas. The simulation model solves the long wavelength limit of the full-F gyrokinetic equation for ion species coupled to the 2D quasi-neutrality equation for electrostatic potential variations, where a fluid model is used for an electron response. The ion-ion collisions are described by the nonlinear Fokker-Plank operator and the effects of anomalous transport are included via a radial diffusion model. Coupling to the 2D fluid code UEDGE is explored in order to improve the electron and neutral models used in COGENT. Illustrative simulations are performed for the parameters of the DIII-D tokamak and compared with the experimental data. The development of 5D COGENT for edge plasma turbulence modeling is also reported. To that end, the slab-geometry 5D version has been developed and successfully verified in simulations of the collisionless drift-wave instability that involve gyrokinetic equations for both ion and electron species coupled to the long-wavelength limit of the 3D gyro-Poisson equation. Recent work is focused on extending the 5D code to include the effects of a tokamak edge magnetic geometry.

Speaker: Dr Mikhail Dorf (Lawrence Livermore National Laboratory)

628 Simulation Study of the Impurity Radiation in the Quasi-Snowfalke Divertor with Ne Seeding for CFETR

It is crucial to exhaust the huge power come from core plasma in future fusion reactor. For a fusion reactor of 1-2 GW fusion power, considering the auxiliary heating power and core radiation, ~200 MW will enter into the scrape-off layer (SOL) and exhausted in the divertor. To find an effective way to exhaust the heat power for future fusion reactor, snowflake divertor (SFD) [D.D. Ryutov, Phys. Plasmas 14 (2007) 064502] is thought as a possible candidate. China Fusion Engineering Test Reactor (CFETR) is proposed to bridge gaps between ITER and DEMO. In our previous SOLPS simulation work [S.F. Mao, et al., J. Nucl. Mater. 463 (2015) 1233], by assuming carbon as the radiation impurity, a reduction in the peak heat flux is shown for the quasi-snowflake (QSF) divertor in CFETR, in comparison with the lower-single-null (LSN) divertor. In order to avoid the fuel retention issue and increase the lifetime of the plasma-facing materials, tungsten wall would be preferred for CFETR, which implies that there will be no intrinsic radiative impurity like carbon. Therefore, radiative impurities, such as neon and/or argon, are indispensable to be seeded. In this work, the radiative SFD with neon seeding are studied by SOLPS simulation. The relation between radiation power, plasma density and effective charge are established for both QSF and LSN divertor. The comparison will give an evaluation of the ability of heat exhaust and compatibility with core plasma for the QSF divertor. Furthermore, the influence of the puffing location on the impurity radiation is also studied, which is considered helpful to find the appropriate impurity seeding scheme.

Speaker: Prof. Minyou Ye (School of Nuclear Science and Technology, University of Science and Technology of China)

IAEA-CN-258-403 YE-Summary Slides.pptx

629 Simulations of Tokamak Boundary Plasma Turbulent Transport

The BOUT++ code has been used to simulate edge plasma electromagnetic (EM) turbulent transport and to study the role of EM turbulence in setting the scrape-off layer (SOL) widths. More than a dozen tokamak discharges from C-Mod, DIII-D, EAST, ITER, and CFETR have been simulated with encouraging success. The simulation results reproduce the measured pedestal turbulence characteristics and the SOL widths. The principal results are: (1) the blobby turbulence originates in the pedestal peak pressure gradient region inside the magnetic separatrix and nonlinearly spreads across the separatrix. The electromagnetic fluctuations provide anomalous transport, which causes particle and heat to be turbulently transported radially down their gradients across the separatrix into the SOL. The electromagnetic fluctuations show the characteristics of both quasi-coherent-modes (QCMs) and broadband turbulence. (2) For simulations of C-Mod EDA H-mode plasmas, the mode spectra are in agreement with the phase contrast imaging data; radial location of the mode is generally consistent with measurements localizing QCMs to the pedestal/separatrix region. For simulations of EAST H-mode plasmas, the mode spectra are in agreement with the probe, interferometer, and POINT diagnostics. A series of simulations also shows that the edge bootstrap current plays a critical role to shift the most unstable mode to lower toroidal mode number, narrow the mode spectrum and enhance radial transport. Therefore, it is suggested to control the peeling modes and associated transport by introducing edge current drive to cancel bootstrap current, for example, by means of lower hybrid waves. This may lead to suppression/mitigation of type-I ELMs and facilitate access to the grassy ELM regime, thus opening a potentially new avenue for steady-state operations in ITER, CFETR and beyond.

Speaker: Xueqiao Xu (Lawrence Livermore National Laboratory)

630 SOL/Divertor Plasma Simulation of Diverging Magnetic Field Configurations for Advanced Divertors

Handling heat loads onto divertor plates is one of the crucial issues. Advanced divertors expand the flux tube of a divertor plasma and reduce the heat load onto the divertor plate. A Super-X divertor (SXD) sets the outer target plate at a further position in major radius than an ordinary divertor (OD) leading to a largely diverging magnetic field (DMF). In order to simulate supersonic plasma flows caused by DMFs without giving any boundary conditions at the target plate, we have developed a plasma fluid model incorporating the anisotropic ion pressure (AIP). The parallel-momentum equation becomes hyperbolic with the AIP. Thus, the plasma flow velocity is calculated from the upstream side without using the downstream boundary condition and supersonic plasma flows in DMFs are consistently simulated with the AIP model even if the actual effect of AIP is small due to high collisionality. By a direct comparison between a conventional fluid model and the AIP model in a DMF configuration with no radial transport, it is demonstrated that a quite smooth and natural profile of supersonic flow velocity which is also observed in the magnetic-nozzle experiment is reproduced with the AIP model while an unphysical profile of plasma flow velocity is obtained with the conventional fluid model. An SXD is also simulated with the AIP model by adding another DMF region to an OD. The plasma flow velocity is increasing in the additional DMF region which might be an advantage for the retention of impurities in the divertor region by the friction force while the plasma density becomes lower which might be a disadvantage for the formation of detached plasmas. The AIP model, therefore, is beneficial to analyze the performance of advanced divertors such as an SXD from the viewpoint of impurity retentions and detached-plasma formations.

Speaker: Dr Satoshi Togo (Plasma Research Center, JpUTsukuba)

material.pdf

631 Solenoid-free start-up utilizing outer PF coils with the help of EBW pre-ionization and change of external inductance in VEST

Solenoid free start-up scenario is the way to utilize loop voltage from the evolution of equilibrium field using outer PF coils. Also, it can be expected to be as an attractive start-up scheme in the fusion machines with low aspect ratio since flux from external inductance change can be utilized. The solenoid free start-up experiments using outer PF coils have been conducted in various devices, but the results show the failure of closed flux surface (CFS) formation or low plasma current with sufficient ECH power. With de creasing vertical field, the experiments for formation of CFS shows that improved pre-ionization with EBW enhances the initiated plasma current by lowering plasma resistivity. The CFS is formed successfully when the poloidal field from plasma current exceeds the vacuum vertical field and the quantitative condition for CFS formation has been derived in the consideration of pre-ionization plasma resistivity. The pre-ionization plasma with low resistivity is necessary for CFS formation. The enhanced particle confinement along mirror ratio in TPC is helpful for lowering resistivity of pre-ionization plasma near outboard and EBW collisionless heating makes possible to have lower resistivity of pre-ionization plasma due to the existence of 2nd or 3rd harmonics near outboard. After the successful CFS formation, the plasma current has been demonstrated to be ramped-up with loop voltage from outer PF coils with help of reduced external inductance. The plasma current evolution has been presented with 0-dimensional power balance modeling with consideration about force balance along plasma current. The initial plasma current evolution has difficulty due to the size of CFS that causes resistive dissipation. Also, the induction voltage from outer PF coils has limitation that it is not easy to change rapidly due to eddy current from vessel wall and causes increase of vertical field that affects to CFS formation and equilibrium. The solenoid free start-up using outer PF coils must consider the distribution between flux from external inductance and resistive dissipation. The solenoid free start-up scheme utilizing outer PF coils has been suggested considering the condition of CFS formation including the location and minor radius of CFS and resistivity of pre-ionization plasma.

Speaker: Mr HyunYeong Lee (Seoul National University)

Summary_FEC_LHY_ver0.pptx

632 SST-1 Cryogenics Requirements and the Way Forward

The SST-1 Machine consists of sixteen TF and nine PF superconducting coils. The cryo stable operation of these coils demand the operation temperature of 4.5 K. This technical requirement is met by 1350 W at 4.5 K helium cryogenic system and is operational since 2003. The SST-1 cryogenics systems include, helium as well as nitrogen cryo systems along with its storage, distribution and recovery systems facilitated to the SST-1 cooling requirements. The cryo system mainly comprises of helium cryogenic system and liquid nitrogen management system. Recent operational experience on SST-1 cryo system has revealed that there is higher heat loads than the installed cryo capacity observed while carrying out simultaneous cooling of the TF and PF coils of the SST-1. It was able to cool down the TF coils along with the current leads and PF3 coils without current leads. Higher pressure drops observed are attributed to higher heat loads in the PF coils. It has been observed that the higher pressure demand of at least 40 g-s-1 at 2.7 – 2.8 bar (a) at 4.5 K with stand-alone cooling of PF coils. That will finally cause the higher pressure demand of at least 40 g-s-1 at 2.7 – 2.8 bar (a) at 4.5 K. In order to provide the simultaneous cooling of the TF and PF coils, we have addressed few short term and long term plans by which we will be able to cool the SST-1 coils as mentioned below, (i) Cryo heat loads minimization within the SST-1 by identifying the possible sources of heat loads and its feasibility to minimize them (ii) Introduction of efficient design of the current leads as “cold capacity saver” (iii) PF3 (U/L) coils operation with the VF coils to get elongated plasma in SST-1 by using NBI cryo plant of capacity 140 W at 4.5 K (short term). However, other PF coils will be cooled down to its best achieved low temperatures using existing 1350 W at 4.5 K helium plant. (iv) Full-fledged PF coils operation with the TF coils by additional similar capacity helium plant (1500 W at 4.5 K) or (v) Designing a cold process using helium compressor / or may be blower (when the heat load mitigation is achieved) and array of heat exchangers pre-cooled by readily available liquid helium (long term). In this paper, a brief review of the installed cryo sub-systems as well as the plans of simultaneous cool down of the TF and PF coils of SST-1 will be discussed.

Speaker: Dr Vipulkumar Tanna (Institute for Plasma Research)

Summary_Slide_CN-258_FIP_P7-8.pdf

633 Stability, Transport, and Active MHD Mode Control Analysis of KSTAR High Performance Plasmas Supporting Disruption Avoidance

H-mode plasma operation in KSTAR has surpassed the n = 1 ideal MHD no-wall beta limit computed to occur at beta_N = 2.5 with l_i = 0.7. High beta_N operation produced beta_N of 3.3 sustained for 3 s, limited by tearing instabilities rather than resistive wall modes (RWMs). High fidelity kinetic equilibrium reconstructions have been developed to include Thomson scattering and charge exchange spectroscopy data, and allowance for fast particle pressure following an approach used in NSTX. In addition, motional Stark effect data are used to produce reliable evaluation of the safety factor, q, profile. The reconstructed equilibria can exhibit significant variation of the q-profile dependent upon the broadness of the bootstrap current profile as computed by TRANSP analysis. Correlations of these differences with observed MHD instabilities are examined to determine favored scenarios for instability avoidance. TRANSP analysis indicates that the non-inductive current fraction has exceeded 50%, and can reach up to 75% while its profile can vary significantly. The stability of the m/n = 2/1 tearing mode that limited the high beta_N operation is computed by using the resistive DCON code and by the M3D-C1 code with the kinetic EFIT as input. For equilibria at high beta_N > 3, the tearing stability index, Delta′, is more unstable compared to that of equilibria at reduced beta_N, indicating that the neoclassical components of tearing stability need to be invoked to produce consistency with experiment. MISK code analysis which examines global MHD stability modified by kinetic effects shows significant passive kinetic stabilization of the RWM. In preparation for plasma operation at higher beta utilizing the new second NBI system, three sets of magnetic field sensors will be used for RWM feedback control. To accurately determine the dominant n-component produced by RWMs, an algorithm has been developed that includes magnetic sensor compensation of the prompt applied field and the field from the induced current on the passive conductors. Developed mode identification using the compensated magnetic signals well measures the toroidal phase of a slowly rotating n = 1 MHD mode. This analysis on stability, transport, and control provides the required foundation for disruption prediction and avoidance research on KSTAR. *Supported by US DOE Grant DE-FG02-99ER54524 and DE-SC0016614

Speaker: Dr Young-Seok Park (Columbia University)

SummarySlide_EX-P7-16_YSPark.pptx

634 Synthetic edge and SOL diagnostics - a bridge between experiments and theory

The Scrape off Layer (SOL) plasma and its coupling with the edge dictate the performance of a discharge to a high degree – especially as all plasma has to go through the SOL, which is the main exhaust channel for the hot plasma. The understanding of the SOL plasma is a key topic in contemporary fusion research. This contribution provides an overview of the modelling efforts of the plasma dynamics in the Scrape-off-Layer (SOL) coupled with the edge. We employ fully dynamical fluid models, e.g. the HESEL code. HESEL simulates density, ion and electron pressure evolution together with the evolution of the generalized vorticity [1] and assumes that the SOL is mainly fuelled at the outboard midplane. Parallel losses, including sheath couplings at the material surfaces, have been parameterized in the SOL. HESEL includes a neutral gas module to model the influence of neutrals on the plasma performance in the SOL and outer edge in their interplay with the intermittent SOL turbulence [2]. For interaction with experiments, HESEL is equipped with synthetic diagnostic tools as probe arrays, Li-beam spectroscopy, and Gas Puff Imaging. Running HESEL in a Kepler workflow, developed within the EUROfusion Integrated Modelling framework[3], allows direct and automated access to experimental data and discharge parameters. A workflow for generating synthetic Lithium beam data, where fluctuation data from HESEL are passed to the RENATE code[4] will be discussed. Using the synthetic probe arrays to measuring the electron and ion heat advection and conduction, we obtain the upstream power fall-off length for a broad range of plasma parameters and by applying non-linear fitting procedures we derive the scaling of the fall-off length with different key parameters. The obtained results are in agreement with recent experimental observations from L-mode AUG data [5]. **References** 1. J. Madsen et al. Phys. Plasmas 23, 032306 (2016); A.H. Nielsen et al. PPCF 59, 025012 (2017) 2. A.S. Thrysøe et al, Plasma Phys. Control. Fusion 58, 4, 44010 (2016) 3. F. Imbeaux et al, Computer Physics Communications, 181(6), 987 – 998 (2010); G. L. Falchetto et al, Proc. 26th IAEA Fusion Energy Conference, TH/P2-13 4. D. Guszejnov et al. Rev. Sci. Instrum. 83, 113 (2012) 5. B. Sieglin et al, Plasma Phys. Control. Fusion 58 055015 (2016)

Speaker: Dr Anders Henry Nielsen (Technical University of Denmark (DTU), Lyngby, Denmark)

635 The effect of electron cyclotron heating on thermal and fast-ions transport in high beta-poloidal discharges at KSTAR

For the realization of the fusion reactor, solving issues for high beta steady-state operation is one of the essential research topics for the present superconducting tokamaks and as a candidate of steady-state scenarios, characteristics of, so called, ‘high beta-poloidal’ discharges[1] is analyzed in depth for the capability of fully non-inductive operation with high bootstrap current fraction. Through the scans of plasma current (Ip ~ 0.4-0.6 MA), toroidal field (BT ~ 1.8-2.7 MA), additional heating (PNBI+ECH ~ 3-5 MW), and plasma density(ne), the access conditions are identified for each parameters for the discharges. Interestingly it is revealed experimentally the discharge characteristics is rather sensitive on the position of EC deposition layer in the core region. Only in a narrow range of the deposition layer, high beta-poloidal regime with H89 ~2.1 is accessible and sustained, while low beta-poloidal regime with H89 ~1.6 exists either without ECH or with outside deposition of the narrow layer. The difference confinement is investigated with MHD activities and the confinement degradation is strongly correlated with high frequency (> 100 kHz) oscillations which are identified as Alfven Eigenmodes (AEs) and also with D-D reduction of neutron rate which suggests the large decrease of fast ion pressure. Therefore, the thermal and fast-ion confinement are analyzed with TRANSP with the measured kinetic profiles and total beta from EFIT magnetic reconstruction. To model the fast-ion transport, ad-hoc diffusion coefficient of fast ions (Dfast) is introduced and determined by detailed comparison of the results of TRANSP and EFIT and the validity of the derived value of Dfast is also confirmed in parallel by neutron rate measurements. In addition, the linear stability of AEs are also examined with MEGA for the onset condition and toroidal mode numbers. According to the analysis, the difference of total confinement(i.e., H89=2.1 and 1.6 respectively) is mainly due to the increased transport of fast ions (i.e., Dfast =0.4 and 1.2 respectively), while there is minor effect from the thermal transport channel (i.e., H98 = 1.1 and 1.0 respectively). Finally, based on the present analysis, the performance enhancement of the high beta-poloidal discharge is predicted for the case with more heating power (PNBI+ECH ~ 10 MW) which is envisaged in two years.

Speaker: Dr Si-Woo Yoon (National Fusion Research Institute)

636 The Influence of Toroidal Magnetic Field Growth on Plasma Performance in the Spherical Tokamak Globus-M/-M2

Globus-M was a compact spherical tokamak with unique features such as plasma column tightly fitted into the vacuum vessel and high NB heating power density. The toroidal magnetic field in it was limited to 0.5 T. Globus-M2 is an upgraded version of Globus-M machine with substantial increase of engineering parameters (the toroidal magnetic field up to 1 T, the plasma current up to 0.5 MA). The goal of the scientific program is to achieve the improved plasma performance with sub-fusion temperature value and collisionality much less than unity in compact geometry and to get closer to the operating conditions of the compact fusion neutron sources. The first plasma experiments ought to be started in 2018. In the final Globus-M experimental campaign the toroidal magnetic field and the plasma current were raised by 25% as compared with routine parameters. As a result an overall improvement in plasma performance was observed. The plasma total stored energy and the energy confinement time grew by about 30% in the discharges with moderate density. D-D beam-plasma neutron rate increased significantly at the same heating power. The main reasons for this effect, in order of importance, are electron temperature rise and fast ion confinement improvement. Decrease of first orbit, sawtooth-induced and TAE-induced fast ion losses was recorded. The energy confinement time growth proportionally to the toroidal magnetic field was observed. The energy confinement time and power decay length scalings, acquired in the experiments, are in a reasonable agreement with MAST and NSTX data. The experiments were continued on the Globus-M2 tokamak with substantially increased values of the toroidal magnetic field and the plasma current.

Speaker: Dr Vladimir Minaev (Ioffe Institute)

Minaev_FIP-P7-34.pptx

637 the ITER plasma current termination phase: physics constraints on control

Following recent characterization of the plasma termination phase from a multi-machine database [1], the ITER termination phase is being analyzed, to define uncertainties due to physics assumptions and to deficiencies in the modeling. Considerable modelling and development has been done on ITER termination scenarios, focussing on specific aspects: magnetic control with transport assumptions [2], or particle exhaust control with assumptions on magnetic control [3]. Because of the high nonlinearity in the plasma response, only time-dependent self-consistent simulations can show whether the proposed termination scheme is robust. None of the available time-dependent equilibrium and transport solvers has a complete and extensive physics scope. However, taken together, these codes offer a wide range of complementary physics models that can be used to identify robust operational ranges for the ITER plasma termination phase. We know from experiments and from extensive vertical stability analysis with DINA that the plasma cross-section and elongation on ITER need to be reduced with current, while at the same time guiding the plasma downward [2]. However, when physics-based models are used for the heating and current drive sources, it is found that the reduction rate of the plasma cross-section in H-mode and the vertical displacement are constrained by the ability of maintaining RF core heating for impurity control and tracking the q=2 surface for NTM control. Based on these preliminary results, the joint modeling activity is looking into (a) level of impurities and their dynamics (b) impurity seeding (c) density decay rate (d) external power stepping-down. The latter, in particular, needs to be adjusted taking into account fast ion stability, fast ion acceleration by IC waves, core heating for impurity control and stabilization of NTMs in H-mode, stabilization of ELMs. The goal is to define new limits on the ramp-down schemes that combine long-term known magnetic control constraints for ITER with new constraints imposed by physics-based models, whose availability in time-dependent simulations is progressively becoming available. [1] P.C. de Vries et al, (2018) Nucl. Fusion 58 026019 [2] Y. Gribov et al, Nucl. Fusion 55 (2015) 073021 [3] F. Koechl et al, Nucl. Fusion 57 (2017) 086023

Speaker: Dr Francesca Poli (PPPL)

638 The physics basis for a solution to the power and particle exhaust problem of a next step device

This contribution presents an overview how research in power and particle exhaust studies relevant to next step devices have advanced our quantitative understanding. For a future fusion reactor, such as the european DEMO, a dissipative power fraction, $f_{diss}$, of $90\%\;-\;97\%$ would simplify the engineering demands on plasma facing components, PFCs. A quantitative understanding of the impact of $f_{diss}$ on confinement is being developed. It is e.g. unclear if ITER could operate with a higher degree of detachment than the currently envisaged and achieve its fusion performance. Seeding of impurities will be mandatory to accomodate the engineering limits of the PFCs. Here, the quantitative understanding of the enrichment of the seed impurities in the divertor is of the essence. The interaction of the plasma with the PFCs together with the volumetric dissipative processes leads to a complex physical system. Based on example cases it is shown how a significant improvement of our qualitative and quantitative understanding of detachment physics has been achieved. The combination of experiments in devices with full metal PFCs, improved diagnostic capabilities and the use of numerical tools with a comprehensive set of physical models provided a major step forward in interpreting experimental data. A steady improvement lead to the identification of missing elements in the models, most prominently the interaction of the numerically expensive drift terms with enhanced far SOL transport. Thus our uncertainty about the highest achievable $f_{diss}$ of the SOL narrows down to the largest extent to a quantitative obscurity about the nature of perpendicular SOL transport. While selected positive example cases of a successful numerical validation against experimental data exist they remain an exception. The certainty with which we can apply our models to interpret experimental data and thus allow for a more general quantitative statement is just starting to be looked at and will need more attention in the future. In view of the complexity of numerical modeling with fluid transport codes, reduced models are being investigated on the basis of experimental data or numerical simulation results. Validated reduced models of various levels of complexity may then be used in system codes to determine the performance of future devices and to specify their design.

Speaker: Dr Marco Wischmeier (IPP Garching)

IAEA_FEC26_2018_Summary_Wischmeier_TH_P7_5_update.pdf

639 The Scrape-off Layer plasma transport physics simulation activity for Indian tokamaks Aditya and SST-1

The computational modelling activity of plasma transport in the Scrape-off Layer (SOL) region of Indian tokamaks Aditya and SST-1 has explored a range of aspects of SOL plasma transport in both the devices. While 2-dimensional computations using SOLPS have predictively addressed aspects of the phase-I of divertor plasma operation of the tokamak SST-1, complete 3-dimensional EMC3-EIRENE computer simulations are applied to the 3D SOL plasma transport in tokamak Aditya operating for over last three decades. The Aditya studies are extended to predict operation scenario of its upgrade version and draw conclusions with respect to experience of SOL physics in its original setup. The phase-I divertor operation scenario of the tokamak SST-1 examined by SOLPS suit of codes recovers access to sheath- and conduction-limited divertor regimes where a transition could be achieved in the edge density scan, affected by the gas puff intensity, beyond $1.5 \times 10^{19}$ m$^{-3}$. A need is indicated to optimize the operating scenario with tolerable target heat loads and low enough density for an effective LHCD operation. The analysis provided estimates of the relative power loading of the inboard and outboard targets for cases with and without control by a localized gas-puff. The Aditya SOL simulations explored the inherently 3D SOL generated by a toroidally localized ring-like limiter in its circular plasma, complementing the localized probe measurements on device SOL. Since the radial diamagnetic drift enters flow continuity with the $E\times B$ and PS flows, it generates a finite flow vorticity, influencing degree of SOL turbulence, cross field diffusivity and the key pedestal parameter $D_{edge}=D_{SOL}$. More recent Aditya Upgrade relevant setups indicate strongly changed connection length distribution, impacting the total recycling flux and modifying parallel and perpendicular plasma fluxes indicating smaller total recycling flux in upgrade for equivalent edge densities in the original setup. A mechanism identified causing excess main chamber recycling relates to observations in ALCATOR C where despite a regular density variation, a radially diverging main chamber plasma flux causes loss of neutral particle control, even for ITER like conditions. The presentation will highlight the characterization of results from the activity for both Aditya and SST-1 tokamaks.

Speaker: Dr Devendra Sharma (Institute for Plasma Research, Bhat, Gandhinagar, India)

640 Thermal Diffusivity Measurement of Functional & Structural Materials for Fusion Blanket Application

Evaluation of thermal profile inside breeding blanket is an important aspect for fusion reactor. Due to thermal neutron flux during steady state operation of future fusion reactor, breeder materials in the blanket will be at elevated temperature up to 900°C. However, during ITER pulse operation with 1800 s pulse length, the maximum estimated temperature is ~650°C. India specific Reduced Activation Ferritic Martensitic (IN-RAFM) steel has been considered as the structural material and various functional materials such as lithium titanate (Li2TiO3) pebbles as the tritium breeder and molten lead-lithium (Pb-Li) eutectic alloy as coolant & tritium breeder have been identified. Li2TiO3 pebbles of 80-90% density will be kept inside the canisters made of IN-RAFMS. To analyze the thermal profile inside the breeding blanket, several simulations are being performed. Thermal properties as a function of temperature and density are the major parameter to perform these simulations. It is therefore necessary to evaluate the thermal diffusivity and thermal conductivity of Li2TiO3 material as a function of temperature and density. The thermal diffusivity of the IN-RAFMS is also measured as a function of temperature from room temperature to 800°C. In the present investigation it is observed that thermal diffusivity of lithium titanate is decreasing from ~0.013 cm2/s at RT to ~0.006 cm2/s at 800 C. However thermal diffusivity of IN-RAFMS is decreasing from ~0.08 cm2/s at RT to ~0.035 cm2/s at 700°C which further increase to ~0.045 cm2/s at 800°C. In the present studies lead lithium samples are also measured from room temperature to its eutectic temperature. Simultaneous measurement of thermal conductivity and specific heat capacity of Li2TiO3 pellet, IN-RAFMS and lead lithium are also discussed in this paper.

Speaker: Mr Aroh Shrivastava (Institute for Plasma Research)

Aroh_IAEA-CN-258_626.pdf

Summery.pptx

641 Thermal-hydraulic Characteristics Study of Superconducting Magnets of SST-1

Steady-state Superconducting Tokamak (SST-1) magnet system consists of NbTi/Cu based CICC (Cable-In-Conduit Conductor) wound Toroidal (TF) and Poloidal (PF) coils. The TF coils are wound in double pancakes (DP), whereas the PF coils are in DP as well as layered winding scheme. These coils are cooled down up to 5 K using force flow circulation of helium. The void fraction of helium within the square CICC (14.8 mm x 14.8 mm, 1.5 mm thick) is about 40%. There are 192 parallel hydraulic paths in the TF coils of lengths about 48 m each. The hydraulic path lengths of PF coils vary from 67 m – 130 m. Experience from several SST-1 cool down campaigns revealed that the PF coils have much higher hydraulic resistance, a factor of three as compared to its ideal expected value with reference to the TF coils. In order to improve the understanding on this issue, cool down trial of PF coils of similar hydraulic path lengths; have been attempted with better control by dividing them in separate groups. The specific experimental campaign carried out to study the thermo-hydraulic behaviour of the SST-1 coils and to investigate the cause of the higher hydraulic resistances within the PF coils. The experiment conducted to measure the hydraulic resistance at room temperature and at subsequent possible lower temperatures. This dedicated experiment revealed that even at lower temperature of 5 K, the pressure drops within the PF coils winding packs are almost three times higher than the ideally expected values. Due to these facts, the simultaneous cooling down of the TF coils and PF coils have not been possible as the cryogenic plant has limited pressure head available in the range of 0.5–0.6 bar. Thermal hydraulic analyses of TF and PF coils have also been attempted to understand the pressure drop experimental data. In this paper, we report the thermal hydraulic behaviour of the TF and PF coils and its comparison with theoretical analysis.

Speaker: Mr Upendra Prasad (Institute for Plasma Research)

summary slide_UP.pdf

642 Thermo-structural and heat load analysis of SST-1 Superconducting coils

Steady-State Superconducting Tokamak-1 (SST-1) has Sixteen Toroidal field (TF) and nine superconducting poloidal field (PF) coils[1]. TF coils are connected in series, whereas, PF coils are to be operated individually in pulse mode. TF coils are operating up to 2.5 T in steady state condition but PF coils have hydraulic as well as heat load issues [2]. In order to operate TF coils and PF coils simultaneously and understand related issues, thermo-structural and heat load analysis have been initiated using ANSYS software.In these analysis, a CATIA model is prepared for SST-1 consisting of superconducting coils, support structure, 80 K cooling system and cryostat. Meshing is done using ANSYS. Initial condition and boundary conditions for temperature, pressure and other constraints in structure are given as inputs from experimental data. Steady state thermal and static structural modules of ANSYS are used for these analyses. Structural analysis of supports, cantilever ring, TF and PF coils, OICS at cryogenic temperatures carried out. Validation of stresses and thermal contraction results compared with analytical results, design and experimental results. Using similar CATIA model, radiative heat loads on PF and TF magnet coils, conduction loads from OICS supports, hydraulic pipes, valves and other instrumentations and on cantilever support ring from ground supports also estimated using ANSYS software. Estimated heat loads due to residual gas conduction, radiation and conduction on various components are compared with analytically calculated and experimental results. Simulated and estimated heat loads are found comparable. Model preparation, meshing, boundary conditions and calculation methodologies will be discussed in this presentation.

Speaker: Mr Arvind Tomar (Institute for plasma research Bhat Gandhinagar India)

FEC-preprints-FIP-P7-21.pdf

summary.pdf

643 Time Resolved Triton Burnup Measurements Using the Scintillating Fiber Detector on KSTAR

For the purpose of fusion triton confinement study on KSTAR, square shaped scintillating fiber detector has been installed and tested during the 2017 KSTAR campaign. It is composed of scintillating fiber bundles which are immersed in the lead matrix. Totally 1,056 scintillating fibers whose cross-sectional area is 1 mm^2 are immersed. The scintillation light is detected by Hamamatsu R878 photo-multiplier tube (PMT) and its anode signal is digitized and processed by CAEN DT5751. From the d-d neutron calibration experiments in National Fusion Research Institute (NFRI) and d-t neutron calibration experiments in the Intense 14 MeV Neutron Source Facility, OKTAVIAN, of Osaka University, the appropriate discrimination level for 14 MeV neutron signal is determined. The operation results in the various plasma conditions are described. In the resonant magnetic perturbation driven edge localized mode (ELM) control experiment case, it is observed that as the RMP applied, ELM mitigated and the amount of burned up triton increased. Each observed results are analyzed by considering possible orbits and slowing down characteristics of fusion triton.

Speaker: Mr Jungmin Jo (Department of Energy Systems Engineering, Seoul National University)

20181020 FEC poster_Jungmin Jo.pdf

summary.pptx

644 Timing and Synchronization for Integrated Operation of Large Volume Plasma Device

The Large Volume Plasma Device (LVPD) [1] is a cylindrical shaped, linear device (length=3m, diameter=2 ) dedicated in carrying out pulsed plasma experiments (tpulse ̃9-50ms )relevant to fusion and Magnetospheric plasma. In the recent past, investigations are switched from active wave plasma investigations to understanding of plasma turbulence of whistler and Electron Temperature Gradient (ETG) nature, relevant to Magneto-spheric and fusion plasmas. In LVPD, efforts are in progress towards enhancing plasma duration from existing 9ms to 50ms in order to cater need of carrying out controlled experiments on Electron Temperature Gradient turbulence, a major source of plasma loss in fusion devices by using variation in density gradient scale lengths. For this purpose, a single console based system for LVPD operation using LabVIEW interface is developed,which will provide timing synchronization to the operation of different subsystems and helps in the implementation of a new Machine operation and Control System (MCS). The timing and synchronization of the heterogeneous I&C modules in terms of centralized clock, trigger, timing and interlocking is critical. The configured MCS consists of (a) PXI based high end instrumentation system for diagnostics data acquisition [2], (b) Process automation system for multiple I&C controllers for slow process [3, 4] and (c) data handling system. This paper discusses results of (a) state of art techniques for timing and synchronization of large physics experiments, (b) centralized timing and synchronization schema, (c) multi-module PXI module clock synchronization on multi-segment PXIe bus, (d) timing and synchronization requirement of high current pulsed power supplies. References 1.S. K. Mattoo, S. K. Singh, L. M. Awasthi, et al., Physical Rev. Lett.108, 255007(2012). 2.R. Sugandhi, P. K. Srivatava, Prabhakar Srivastav, et al., 7th Int. Conference on Cloud Computing, Data Science and Engineering, IEEE conference series, 804(2017). 3.R. Sugandhi, P. K. Srivastava, A, K, Sanyasi, et al., Fusion Engineering and Design112, 804 (2016). 4.R. Sugandhi, P. K. Srivastava, A. K. Sanyasi, et al., Fusion Engineering and Design 115, 49(2017).

Speaker: Mr Ritesh SUGANDHI (Institute for Plasma Research, Gandhiangar, India)

summary_slide_fip_p7_16.pdf

645 Velocity Profile and modulation frequency of Ions in a Magnetized Plasma Sheath using kinetic trajectory simulation method

In all bounded plasmas, plasma sheath plays an important role in its stability as well as in determining the particle fluxes and energies reaching the wall. Velocity variation as well as modulation frequency of ions in a magnetized plasma sheath has been studied for different obliqueness as well as strength of the field. Due to sharp gradients of physical parameters in the sheath region fluid theory has singularity and we have used the kinetic trajectory simulation model, where the characteristic equations of motion are solved iteratively unless a self-consistent state is achieved for given particle distributions at boundaries. Variation of ion velocities, their mean values, maximum amplitude, damping factor as well as frequency of oscillation are studied for constant magnetic field at different obliqueness as well as for different magnetic fields considering the same obliqueness. The kinetic approach is expected to give better understanding of velocity profiles and hence is of interest in divertor type Tokamaks, where the field lines outside the last-closed-flux-surfaces strike the wall at different angles.

Speaker: Dr Raju Khanal (Tribhuvan University)

PPT_FEC2018.pptx

646 Wide divertor heat-flux width in ITER from self-organization between the neoclassical and turbulent transports across the separatrix surface

A serious concern for ITER operation is the ability for the divertor to withstand the steady plasma exhaust heat that will be deposited on the divertor surface along a narrow toroidal strip. A simple, data-based regression from experimental measurements in present devices shows we would have λq≲1mm for ITER operation at Ip=15 MA. However, it is questionable if such a simple extrapolation is valid as there may be differences in fundamental edge physics between ITER plasmas and those in present devices. Therefore, any extrapolation from present experiments to ITER needs to have a solid physics basis, which is one of the goals of the gyrokinetic edge code XGC1. Prediction for λq by XGC1 has been validated on several representative C-Mod, DIII-D, NSTX, and JET plasma conditions. However, when the same code is applied to a model ITER plasma at Ip=15MA, surprisingly, λq≈6mm is obtained [1]. Another abnormality is noticed from high current, high triangulariry NSTX-U model plasma simulations. A substantial new understanding has been obtained after the 2016 IAEA-FEC for physics behind the enhanced divertor heat-flux width. XGC1 data reveals an interesting competition effect between the neoclassical and turbulent transports. In the “conventional” tokamaks that obey the Eich scaling [2], a “blob-type” edge turbulence exists across the magnetic separatrix Ψn>0.97. On the other hand, in ITER, a “streamer-type turbulence” extends to Ψn>0.97 due to the small $\rho_i /a$ effect. The streamer-type turbulence is much more efficient in the radial transport across the magnetic separatrix surface, with the pressure and potential perturbation being highly off-phase, than the blob-type turbulence is. We note here that even with $\rho_i /a$, the X-point orbit loss and a strong spontaneous co-rotation in the edge plasma supports a reasonably strong pedestal in ITER that is ~2X wider than the MHD predicted width. This work is mostly funded by US DOE and ITER. Computing resource is provided by OLCF and NERSC. [1] C.S. Chang et al., IAEA-FEC 2016, TH/2-1; Nucl. Fusion 57 (2017) 116023 [2] T. Eich et al., Nucl. Fusion 53 (2013) 093031

Speaker: Dr Choongseok Chang (Princeton Plasma Physics Laboratory)

Chang_TH-P7-22_Summary.pdf

Chang_TH-P7-22_Summary.pptx

Summary_Chang_TH-P7-22.jpeg

10:15 Coffee Break

MPT/2, FNS/1, SEE/2 Materials, Fusion Nuclear Science, Environmental

647 High-temperature creep properties of NIFS-HEAT-2 high-purity low-activation vanadium alloy

The National Institute for Fusion Science (NIFS) developed the NIFS-HEAT in collaboration with Japanese universities. Previous heats exhibited brittle fracture of weld joints and cracking during tubing fabrication at room temperature, due to ductility loss caused by interstitial impurities, such as C, N and O. The total of interstitial impurity level of NH2 is almost half that of the US heat. As a result, weldabilty and workability were successfully improved because of enhanced ductility. Although many properties were improved by the purification, possible degradation of high-temperature strength due to purification softening was a concern. Therefore, the present study evaluated the high-temperature creep properties of NH2, which were expected to be sensitive to impurity levels. Creep rupture time of NH2 in the lower applied stress region (≤ 100 MPa) was comparable to the US heat at 800°C, although in the higher stress region, the rupture time was shorter than that for US data. The creep activation energy of the US heat was 320 kJ mol^-1 in average, and consistent with 270 kJ mol^-1 for self-diffusion energy in pure vanadium. This indicates that climb-assisted dislocation motion is the predominant process for creep. NH2 showed higher activation energy, 640 kJ mol^-1, suggesting additional deformation process. Since the applied stress in the creep tests, 150 to 200 MPa, was close to the yield stress (195 MPa) of NH2, thermally activated dislocation glide was thought to be induced and thus enhanced creep. The creep data were converted by time-temperature equivalence scaling using the Larson-Miller parameter. Some of the parameters for NH2 are smaller than those for the US heat, however are still superior to fusion-grade steels. As mentioned above, creep properties were not degraded by the purification at stress levels ≤ 100 MPa. This means that the purification requires no change in design stress for blanket, because the thermal stress would be less than this level, assuming the first wall consists of a simple edge-constraint plate with heat flux and wall thickness of less than 1 MW m^-2 and 5 mm, respectively. In conclusion, the purification for NH2 improved many properties, such as weldability and workability, and raised no negative effect on high-temperature creep properties under the projected blanket service stresses.

Speaker: Mr Takuya Nagasaka (National Institute for Fusion Science)

IAEA_FEC_2018_Nagasaka_vanadium_creep_1_page_summary_Ver2.pptx

IAEA_FEC_2018_Nagasaka_vanadium_creep_Ver9_s_wide.pptx

648 Model validation on EAST and DIII-D experiments towards understanding of high-Z material erosion and migration in a mixed materials environment

The 3D Monte Carlo code ERO taking into account a material mixing surface model has been used to simulate tungsten (W) erosion and migration on EAST with an upper full W divertor and DIII-D with toroidally continuous W rings embedded in the divertor target. Modeling shows that the transport of carbon (C) impurities not only dominates the W sputtering source but also determines the overall erosion and deposition balance in the mixed materials surface. With a self-consistent calculation of transport of C impurities and taking into account the re-erosion of W by returned eroded particles, W gross erosion rates measured by WI spectroscopy can be well reproduced by the modeling for both devices. The ExB drift and lower electron temperature at the radial outboard side lead to a net deposition zone where W and C are accumulated, which is consistent with the measurements with several changeable inserts in a specially designed collector probe at the DiMES system in DIII-D. In the net erosion zone closer to the outer strike point, the W coverage on C is very low and saturated independent of exposure time, agreeing with the measurements by collector probes. Strong sheath effects on material erosion rates have also been observed using external biasing samples. The particle flux and material erosion as a function of biasing voltage have been analyzed by the SPICE2 and the ERO code. Both the PIC simulation and the Dα emission measured by a fast camera reveal that with increasing biasing voltage the ion flux decreases at the biased area while increases at the adjacent downstream tile, although the biased sample potential is far below the plasma potential. Detailed modeling shows that the ion flux variation at different area is due to the strong gradient of the electric field in the sheath, which results in different magnitude of the polarization drift above the biased and non-biased surface. The reduced ion flux and incident energy are responsible for more than an order of magnitude reduction of erosion with slight positive voltage biasing in the experiments. The critical role of C impurities and the sheath in determining high-Z material erosion and migration have been revealed. This understanding indicates promising methods for erosion control, which is critical for material lifetime, plasma impurity content, and tritium retention in future fusion reactors.

Speaker: Dr Rui Ding (Institute of Plasma Physics, Chinese Academy of Sciences)

presentation

Summary Slides

649 Evaluation of Tungsten as Divertor Plasma-Facing Material: Results from Ion Irradiation Experiments and Computer Simulations

Tungsten has emerged as divertor-plasma-facing material in fusion reactors due to its excellent thermal and mechanical properties as well as low tritium affinity. It is therefore essential to understand the behavior of tungsten in reactor-like conditions from the point of view of radiation damage and fuel retention. There is already a world-wide effort in creating a database of radiation damage and retention by surrogate ion irradiation. In this paper, we present results of experiments and computer simulations of radiation damage and deuterium trapping due to light, medium and heavy ions in poly-crystalline tungsten. The idea is to develop a deeper understanding of the radiation damage, evolution of the defects and their impact on hydrogen-isotope trapping. Several irradiation experiments have been carried out with ions of Au, W, B, He and D of energies ranging from 100keV-80MeV. We have found that for the same fluence (1.3 x 1018 ions-m-2) of the impinging ions, the ion-mass plays a critical role in the defect creation and subsequent deuterium trapping. The samples irradiated with 80 MeV Au ions were found to show more D-isotope retention in comparison with 10 MeV boron ions. The range of both the ions were similar. For an order of magnitude higher fluence of boron (1.0 x 1019 ions-m-2), the trapped deuterium content was considerably lower than that of Au. The defect density observed Au irradiated sample was several orders of magnitude higher than the B irradiated ones. A similar observation was also confirmed using low temperature resistivity measurements. In MD simulations, we see that at large energies of the Primary Knock-on Atom (>160 keV) the fragmentation of the cascade occurs which may have a direct relation to the experiments of heavy ion irradiation at 80 MeV where we see prominently dense clustering of dislocations and vacancies. Interestingly 10 MeV boron damage seems to produce PKA spectrum somewhat similar to that of 14 MeV neutron which is distinctly different than the defects produced and consequently deuterium trapping from heavy ion irradiation. These results will be presented along with computer simulations and limits to extrapolation damage from surrogate to neutrons will be highlighted.

Speaker: Dr Padivattathumana N. Maya (ITER-India, Institute for Plasma Research, Bhat, Gandhinagar)

FEC_MPT_2-3_Maya.pdf

650 The European approach to the fusion-like neutron source: The IFMIF-DONES Project

The need of a neutron source for the qualification of materials to be used in future fusion power reactors have been recognized in the European (EU) fusion programme since many years. The construction and exploitation of this facility is presently considered to be in the critical path of DEMO. This issue prompted the EU to launch activities for the design and engineering of the IFMIF-DONES (International Fusion Materials Irradiation Facility-DEMO Oriented Neutron Source) facility based on and taking profit of the results obtained in the IFMIF/EVEDA (‘Engineering Validation and Engineering Design Activities’) project, presently conducted in the framework of the EU-Japan Bilateral Agreement on the Broader Approach to Fusion. These activities and R&D work for the IFMIF-DONES Plant are presently taking place in the framework of a work package of the ‘EUROfusion’ Consortium, in direct collaboration with ‘Fusion for Energy’ Organization. The main objective of these activities is to consolidate the design and the underlying technology basis in order to be ready for IFMIF-DONES construction as early as possible. This paper presents the main engineering results for a generic site obtained during the first years of design work, as indicated in the recently released IFMIF-DONES Preliminary Engineering Design Report, making emphasis on the design evolution from previous phases and on the critical issues to be further developed in the near future. The proposed European site to host the facility (Granada Spain) is briefly introduced as well. This work has been carried out within the framework of the EUROfusion Consortium and has received funding from the Euratom research and training programme 2014-2018 under grant agreement No 633053. The views and opinions expressed herein do not necessarily reflect those of the European Commission, Fusion for Energy, or of the authors' home institutions or research funders.

Speaker: Dr Angel Ibarra (CIEMAT)

181022FEC_IbarraDONES-v3.pptx

651 Waste implications from minor impurities in European DEMO materials

Waste-production predictions for the future demonstration fusion power plant (DEMO) are necessary to produce an accurate picture of the likely environmental and economic costs of radioactive waste disposal at end-of-life (EOL). Even during the conceptual stage of DEMO design it is important to perform waste assessment so as to avoid potential surprises caused by design flaws that could lead to unacceptable levels of long-term high-level waste. An integrated simulation process combining Monte-Carlo neutron transport simulations, high-fidelity inventory calculations, and extensive and reproducible post-processing algorithms has been used for the evolving European DEMO designs to quantify the time-varying mass inventories in different waste classes for individual regions and components of the reactor vessel, as well as for the reactor as a whole. Waste categories based on UK regulations reveal that minor impurities contained in certain materials, such as Eurofer, tungsten, and beryllium, can have a significant impact on the waste classification prospects of materials, potentially leading to the production of waste that will remain as intermediate level-waste (or worse) for hundreds of years beyond DEMO EOL. The computational framework developed for these assessments can be rapidly and continuously applied to the maturing DEMO design, helping to guide design choices to mitigate long-lived waste production and ensure that most waste becomes low-level waste (or better) within a few decades.

Speaker: Dr Mark Gilbert (CCFE)

mgilbert_FEC_oct2018.pdf

12:30 Lunch

EX/7-TH/5-EX/8,PPC/2-TH/6-EX/9-TH/7-EX/10-TH/8-EX11-PD P8 Posters

652 3D structure of density fluctuations in T-10 tokamak and new approach for current profile estimation

Speaker: Dr Vladimir Vershkov (ITF NCR "Kurchatov Institute")

653 Benchmarking of Full-f Global Gyrokinetic Modeling Results Against the FT-2 Tokamak Doppler Reflectometry Data Using Synthetic Diagnostics

Speaker: Mr Alexey Altukhov (Ioffe Institute)

RCDR_synth_slide.pptx

654 Demonstration of Power Exhaust Control by Impurity Seeding in the Island Divertor at Wendelstein 7-X

Speaker: Dr Florian Effenberg (Department of Engineering Physics, University of Wisconsin - Madison)

FEC_IAEA_Talk_2018_Effenberg.pdf

Summary_Slide_EX92_Effenberg.pdf

655 Dynamic ELM and divertor control using mixed toroidal harmonic resonant magnetic perturbations in DIII-D and EAST

Speaker: Dr Youwen Sun (Institute of Plasma Physics, Chinese Academy of Scienses)

656 Effect of multiscale interaction between an m/n=2/1 mode and micro instabilities on transport of KSTAR plasmas*

Speaker: Dr Minjun J. Choi (National Fusion Research Institute)

summary_slide.pdf

summary_slide.pptx

657 ELM Control Physics with Impurity Seeding and LHCD in the HL-2A Tokamak

Speaker: Mr Guoliang Xiao (Southwestern Institute of Physics，China)

EX7-4 ELM Contro Summary slide.pptx

658 Erosion, Screening, and Migration of Tungsten in JET Equipped with Tungsten Divertor

Speaker: Dr Sebastijan Brezinsek (Forschungszentrum Jülich)

Single_Slide_Brezinsek.pptx

659 Experimental conditions for suppressing Edge Localised Modes by magnetic perturbations in ASDEX Upgrade

Speaker: Dr Wolfgang Suttrop (Max-Planck-Institut für Plasmaphysik)

wsuttrop_fec2018_poster.pdf

wsuttrop_fec2018_SummarySlide.pdf

660 Experimental Evidence of Lower Hybrid Wave Scattering in Alcator C-Mod due to Scrape Off Layer Density Fluctuations

Speaker: Dr Gregory Wallace

SUMMARY.pdf

661 Explaining Cold-Pulse Dynamics in Tokamak Plasmas using Local Turbulent Transport Models

Speaker: Mr Pablo Rodriguez Fernandez (UsPSFC)

662 Exploring an Alternate Approach to Q=10 in ITER

Speaker: Dr Timothy C. Luce (General Atomics)

Luce_summary.pdf

663 First divertor physics studies in Wendelstein 7-X

Speaker: Prof. Thomas Sunn Pedersen (Max Planck Institute for Plasma Physics)

IAEA_single_slide.pptx

664 Gyrokinetic XGC1 Simulation Study of Magnetic Island Effects on Neoclassical and Turbulence Physics in a KSTAR Plasma

Speaker: Dr Jae-Min Kwon (National Fusion Research Institute)

jkwon IAEA 2018 - upload.pptx

Kwon - IAEA summary.pptx

Kwon - IAEA summary r1.pptx

665 Isotope effect on impurity and bulk ion particle transport in the Large Helical Device

Speaker: Dr Katsumi Ida (National Institute for Fusion Science)

666 Modelling third field operation in the ITER pre-fusion power operation phase

Speaker: Dr Mireille SCHNEIDER (ITER Organization)

667 nonlinear 2-fluid study of the effect of pellet injection on ELM dynamics

Speaker: Dr Debasis Chandra (Institute For Plasma Research, INDIA)

sumslide_dchandra_th5-1_FEC18.pdf

668 Origin of Harmonics of Drift Tearing Mode in ADITYA tokamak

Speaker: Ms Harshita Raj (Institute for Plasma Research)

669 Predicting Scrape-Off Layer profiles and filamentary transport for reactor relevant devices

Speaker: Dr Fulvio Militello (Culham Centre for Fusion Energy)

670 Predictions of alpha-particle and neutral-beam heating and transport in ITER scenarios

Speaker: Dr Eric M. Bass (University of California San Diego)

Bass IAEA-FEC 2018 16x9 PDF form.pdf

Bass IAEA-FEC 2018 16x9.ppt

Bass IAEA-FEC 2018 poster.pdf

671 Progress in DIII-D Towards Validating Divertor Power Exhaust Predictions (

Speaker: Dr Aaro Jaervinen (Lawrence Livermore National Laboratory)

672 Real-time simulation of the NBI fast-ion distribution

Speaker: Markus Weiland (Max-Planck-Institut für Plasmaphysik)

673 Recent advances in ICRF heating of mixture plasmas: survey of JET and AUG experiments and extrapolation to JET-DT and ITER

Speaker: Dr Yevgen Kazakov (Laboratory for Plasma Physics, LPP-ERM/KMS)

Kazakov-IAEA-FEC2018-summary-slide.pdf

674 Study of passively stable, fully detached divertor plasma regimes attained in innovative long-legged divertor configurations

Speaker: Dr Maxim Umansky (Lawrence Livermore National Lab)

IAEA_mvu.v6.pdf

mvu_summary_2018.v1.pdf

675 Test of the ITER-like RMP configurations for ELM-crash-suppression on KSTAR

Speaker: Prof. Yongkyoon In (Ulsan National Institute of Science and Technology)

EX/8, PPC/2 - TH/6 Heating, Current Drive & Steady State

676 Modelling third field operation in the ITER pre-fusion power operation phase

The ITER low activation phase consists of H and He plasmas, split into Pre-Fusion Power Operation phases 1 and 2 (PFPO-1 and PFPO-2). The PFPO-1 phase will include 20 MW of Electron Cyclotron Resonance Heating (ECRH) and possibly 10 MW of Ion Cyclotron Radio Frequency Heating (ICRH), while the PFPO-2 phase will include the full Heating and Current Drive (H&CD) capabilities, i.e. 73 MW of H&CD power. The L-H power threshold displays a density optimum for ITER q95 = 3 operation at n/n_G~0.4 , where n_G is the Greenwald density. At half field for n/n_G~0.4 in PFPO-1, H-mode access is predicted to be unlikely in PFPO-1 in H and marginal in He. Accessing H-mode allows the determination of the heating power required to operate ITER in H-mode and to commission/demonstrate ELM control schemes, both of which are key to the research plan. Hence, operating 5MA/1.8T (q_95=3) plasmas is foreseen, since it makes the H-mode access more likely in PFPO-1. Scenarios have been developed for both PFPO-1 and PFPO-2 phases. H-mode scenarios at 1.8T and low density are developed according to the limited power installed in PFPO-1, providing the density upper limit, and to the fact that low density and dominant ECRH can lead to low edge ion power flow preventing H-mode access. Hence it is important to qualify which key elements can be addressed in such plasmas to determine whether the required resources to implement the 1.8T research programme are worthwhile. Integrated simulations of ITER 5MA/1.8T plasmas have been carried out with various 1.5D transport integrated modelling suites of codes by the ITPA topical group on Integrated Operation Scenarios (ITPA-IOS) in collaboration with the IO and with support from the ITPA Transport and Confinement and Energetic Particles groups. The present contribution reports the results of self-consistent transport and H&CD analyses to assess the efficiency of EC and IC heating in 5MA/1.8 T plasmas in L and H-modes. With a view to study H-modes at 1.8T in PFPO-2, the possibility to heat these plasmas with NBI has been assessed as well. These issues are assessed by the application of a range of integrated modelling suites, used in association with either simplified H&CD models or more sophisticated codes for ECRH,ICRH and NBI modelling.

Speaker: Dr Mireille SCHNEIDER (ITER Organization)

Schneider - Presentation - Modelling one third field operation in the ITER PFPO phase - IAEA 2018 -TH 6-1 - V9.pptx

Schneider - Summary Slide - Modelling one third field operation in the ITER PFPO phase - IAEA-TH 6-1.pptx

677 Predictions of alpha-particle and neutral-beam heating and transport in ITER scenarios

We present predictions of the ITER fusion-alpha and neutral-beam-injection (NBI) ion density and power-deposition profiles using a stiff transport critical gradient model (CGM) for Alfvén eigenmode (AE) transport in various ITER scenarios. In a burning plasma such as planned in ITER, deposited heat from fusion-born 3.5 MeV alpha particles provides most of the power needed to sustain fusion. Under current plans, high-energy (1MeV) neutral beam injected (NBI) ions will provide much of the remaining steady-state power. Both processes rely on energetic ions slowing down through collisions with electrons, depositing most of their energy into central plasma heat before being lost. Moreover, edge loss of inadequately slowed EPs poses a risk to plasma-facing components, particularly if such losses are concentrated in intermittent bursts. Looking principally at AE transport, the greatest identified risk, we will show that lower current and reversed-shear ITER scenarios show a decrease in EP confinement. We also show that increasing the NBI fraction of auxiliary heating degrades confinement for both the alpha particles and beam ions. The time-averaged EP profile prediction tools developed for this study have been verified against first-principles nonlinear simulations [1,2] and validated against a beam-heated DIII-D discharge [3]. A new fast computation of the critical gradient [4] eases integration into whole device modeling (WDM) frameworks. Also, a new quasilinear time-dependent transport model is used to investigate transport intermittency. [1] E. M. Bass and R. E. Waltz, Phys. Plasmas 17, 112319 (2010) [2] E. M. Bass, and R. E. Waltz, Phys. Plasmas 24, 122302 (2017). [3] R.E. Waltz, E.M. Bass, W.W. Heidbrink, and M.A. VanZeeland, Nucl. Fusion 55 123012 (2015). [4] He Sheng, R. E. Waltz, and G. M. Staebler, Phys. Plasmas 24, 072305 (2017). [5] R.E. Waltz and E.M. Bass, Nucl. Fusion 54, 104006 (2014). [6] G. M. Staebler, J. E. Kinsey, and R. E. Waltz, Phys. Plasmas 14, 55909 (2007). [7] J. Candy and R. E. Waltz, J. Comput. Phys. 186, 545 (2003). [8] K. Ghantous, H. L. Berk, and N. N. Gorelenkov, Phys. Plasmas 21, 032119 (2014) *Work supported by U.S. Department of Energy under Grants DE-FG02-95ER54309 (theory), DE-FC02-08ER54977 (SciDAC-GSEP project), and DE-SC0018108 (SciDAC-ISEP project)

Speaker: Dr Eric M. Bass (University of California San Diego)

Bass_IAEA-FEC_2018_16x9.ppt

BASS IAEA FEC 2018 Summary slide.pdf

678 Exploring an Alternate Approach to Q=10 in ITER

Stable and robust ITER Baseline Scenario demonstration discharges have been achieved in DIII-D at zero injected input torque (matching the ITER LSN shape including the aspect ratio, betaN=1.9-2.05, and q95=3), and repeated under various conditions (Ip, density, wall conditions). However, an alternate route to Q=10 conditions has been explored that starts at higher q95 and maximum BT. Performance to reach 500 MW of fusion power is reached at all torque levels. With co-NBI, the goal is reached by 11 MA equivalent, and the achieved beta does not increase above 12.5 MA. At zero torque, 13.5 MA may be sufficient to reach P_fus=500 MW. The gain metric βτ does not improve above 13 MA equivalent (which corresponds to q95~3.7), and all torque curves show the same trends for the evolution to saturation. This indicates that this saturation effect, observed previously in DIII-D, is not likely to be due to an ExB shear effect.
Comparing 15 and 13 MA equivalent cases, three causes for the confinement changes will be assessed: (i) differences in dimensionless parameters such as rho, beta, nu, q; (ii) increase in the sawtooth inversion radius at higher current; (iii) broadening of the NBI deposition profile. The fusion gain metric beta*tau saturates around the 13 MA equivalent mark for all torque values, so the benefits to fusion energy performance of increasing current may not be fully realized. Further study is needed to determine the origin of this.

Speaker: Dr Timothy C. Luce (ITER Organization)

Luce_IAEAOral_20181026.pdf

679 Real-time simulation of the NBI fast-ion distribution

Knowledge of the fast-ion distribution arising from neutral beam injection (NBI) is important for transport analysis and magnetic equilibrium reconstruction. For sophisticated plasma control, which will be essential for the success of future fusion devices, it is very beneficial to know this distribution function already in real-time during the discharge. Then, the relevant quantities (e.g. heating profiles, current-drive etc.) can be fed to real-time transport and equilibrium codes like RAPTOR, which estimate kinetic and current density profiles in real-time. Beyond real-time applications, such fast models are essential for optimization problems, e.g. reactor design studies or discharge planning. Several sophisticated models exist, that can calculate this beam ion distribution in good agreement with experimental data, such as the Monte-Carlo code NUBEAM. The high accuracy of these codes has, however, to be paid with relatively intensive numerical efforts, which compromises their use in real-time applications. In this contribution, we present the novel code RABBIT (Rapid Analytically Based Beam Injection Tool). RABBIT currently takes $\approx$25\,ms per time step, which is roughly a factor of 1000 faster than the NUBEAM code. The approximations needed to arrive at this goal are discussed. Benchmarks are carried out with the more accurate but also much slower NUBEAM code, indicating a good agreement. Several applications of the model on different machines are carried out. RABBIT is run in real-time in the discharge control system of ASDEX Upgrade to improve active plasma control. In addition, RABBIT is being used for accurate equilibrium reconstructions (with the IDE code) in between shots. This facilitates the development of advanced scenarios, where a fine-tuning of the $q$-profile is desired. On DIII-D, RABBIT is foreseen to be used in experiments with the goal to demonstrate real-time control of Alfvén eigenmodes (AE). Here, the neutron rate prediction from RABBIT is compared to the measured neutron rate to detect appreciable fast-ion transport. In conjunction with direct AE detection with ECE diagnostics, when detrimental conditions are observed, counter-measures to stabilize AEs can be activated during the discharge. This could be of great importance for future fusion reactors, where strong AE activity is expected.

Speaker: Markus Weiland (Max-Planck-Institut für Plasmaphysik)

summary_slide2.pdf

weiland_iaea2.pdf

weiland_iaea2_stretched_white.pdf

680 Recent advances in ICRF heating of mixture plasmas: survey of JET and AUG experiments and extrapolation to JET-DT and ITER

This contribution summarizes recent theoretical and experimental developments of a novel 'three-ion species' heating scheme that have opened new promising avenues for the application of ICRF in fusion plasmas. Following successful proof-of-principle demonstration on the Alcator C-Mod and JET tokamaks [1], this scenario has also been recently established on AUG. A small amount of 3He ions (~1% and below) was injected into H-D plasmas to absorb RF power and heat the plasma. In JET experiments, effective plasma heating was observed both at extremely low 3He concentrations of ~0.1-0.2% (maximized fast-ion content) and at moderate concentrations of ~1-1.5%. We further enhanced the efficiency for fast-ion generation and plasma heating by changing the configuration of ICRH antennas from dipole to +pi/2 phasing. Heating AUG plasmas with this ICRF scenario requires 3He ions to be less energetic than in JET. The combination of moderate 3He concentrations of ~1% and off-axis 3He resonance was successfully applied to reduce fast-ion energies and thus improve confinement of RF-heated ions in AUG. ICRH modeling with the state-of-the-art codes SCENIC [2] and TORIC-SSFPQL has been used extensively to validate JET and AUG experimental observations. In a next-step, we also successfully demonstrated effective heating of JET H-D mixtures using the fast injected D-NBI ions as resonant 'third' species [3]. The scenario was tuned such that D-NBI ions with injection energy of 100keV absorbed most of launched RF power and were accelerated with ICRF up to ~2MeV. The observed ten-fold increase in the neutron rate and its temporal evolution were successfully reproduced with the time-dependent TRANSP modeling. The established technique of accelerating NBI ions in mixture plasmas to higher energies can be applied to generate alpha particles in D-3He plasmas and to maximize D-T fusion reactivity. Finally, we conclude with a discussion of the application of these novel ICRF scenarios for future JET-DT and ITER operations [4]. [1] Ye.O. Kazakov, J. Ongena, J.C. Wright, S.J. Wukitch et al, *Nature Physics* **13**, 973-978 (2017) [2] J.M. Faustin et al, *Plasma Phys. Control. Fusion* **59**, 084001 (2017) [3] J. Ongena, Ye.O. Kazakov et al, *EPJ Web Conf.* **157**, 02006 (2017) [4] M. Schneider, J.-F. Artaud, P. Bonoli, Y. Kazakov et al, *EPJ Web Conf.* **157**, 03046 (2017)

Speaker: Dr Yevgen Kazakov (Laboratory for Plasma Physics, LPP-ERM/KMS, Brussels, Belgium)

Kazakov-IAEA-FEC2018-summary-slide.pdf

Kazakov-IAEA-FEC2018-talk-FINAL.pdf

681 Experimental Evidence of Lower Hybrid Wave Scattering in Alcator C-Mod due to Scrape Off Layer Density Fluctuations

We present new experimental measurements of the Lower Hybrid (LH) wave electric field vector, $E_{LH}$, obtained in Alcator C-Mod and provide a direct comparison with 3D full-wave COMSOL simulations using the cold plasma dielectric tensor and reflectometry measured density profiles. Two key results are reported: 1) The direction of $E_{LH}$ was found to have a substantial poloidal component and is in strong disagreement with the nearly radial full-wave simulation result. 2) Adding Scrape Off Layer (SOL) density fluctuations to the density profile implemented in the full-wave simulations can be used to explain the $E_{LH}$ direction discrepancy.

Polarized passive optical emission spectroscopy was implemented to determine $E_{LH}$. This technique entails measuring two orthogonally polarized $D_\beta$ spectral line profiles. The spectra are simultaneously fit to the Schrodinger equation containing both magnetic and time periodic electric field operators. The three components of $E_{LH}$ are the only fit variables. The experimental $E_{LH}$ results were compared to axisymmetry 3D full-wave COMSOL simulations via a synthetic diagnostic. Comparing the experimental and simulation results, good agreement was found with regard to the magnitude of $E_{LH}$ both as a function of measurement location and LH power. However, it was found experimentally that $E_{LH}$ contained a poloidal component having a magnitude on the order or greater than that of the radial component. The poloidal component was found to be a strong function of poloidal angle, increasing towards the midplane, and a weak function of toroidal angle, remaining nearly constant. This result strongly disagrees with the nearly radial $E_{LH}$ predicted by the full-wave simulations. SOL density fluctuations based on an experimentally verified 3D BOUT turbulence simulation of a similar Alcator C-Mod discharge were added to the density profile. We found that diffraction and scattering from a realistic turbulence model generates a substantial poloidal component in $E_{LH}$, significantly closing the gap between the experimental and simulation results. This result indicates that SOL turbulence can have a detrimental effect on LHCD performance if the wavelength is on the order of the turbulence characteristic scale length.

Speaker: Dr Gregory Wallace (MIT Plasma Science and Fusion Center)

EHM_IAEA_16x9.pdf

EHM_IAEA_32x9.pdf

SUMMARY.pdf

P8 Posters

682 3D heat and particle fluxes in Wendelstein 7-X

Many present and future large magnetic fusion experiments need to consider the 3D topology of the heat and particle exhaust either due to application of external magnetic perturbations to mitigate type-I ELMs or because it is typically inherent to the magnetic configuration of the device (e.g. LHD or W7-X). In both cases, the scrape-off layer forms heterogeneous 3D structures of field lines with different connection lengths. A key question to future and present devices is in how far the presence of 3D boundary affects the plasma-wall interaction whith toroidal symmetry not preserved anymore. W7-X in its recent campaign with an uncooled fine-grain graphite divertor investigated for the first time in full detail a concept of an island divertor, which uses intrinsic large, low resonance island chains at the plasma edge to form heat and particle exhaust channels. The measured strike line width is of up to 10 centimeters with its 3D geometry strongly depending on the magnetic configuration. Similar findings are observed at LHD, whch is typical for any device with a stochastic boundary independent if it is a tokamak or a stellarator. In steady state operation, assumptions that power loads follow the periodicity of the device cannot be made, therefore 10 high-resolution infrared/visible systems are installed to monitor the heat and particle fluxes over the whole divertor surface. We have developed new methods to characterize the local and global heat and particle loads based on recent experimental observations, e.g. by projecting the measured heat flux onto the geometry of the islands forming island divertor. The energy of particles deposited at the strike line varies strongly with plasma density as shown by floating potential. At very low densities a strong negative potential (<-60 V) has been measured by divertor Langmuir probes, whereas at higher densities it goes even slightly positive. In addition, the electron temperatures at the strike line vary strongly depending on the plasma parameters from below 5 eV during divertor heat flux detachment to ca. 100 eV at very low plasma collisionalities. The data from LHD, W7-AS and W7-X shows that the measured heat and particle flux patterns are rather sensitive to magnetic configuration, changes in finite plasma beta and arising toroidal currents.

Speaker: Dr Marcin Jakubowski (Max-Planck-Institut für Plasmaphysik, Greifswald, Germany)

683 A Travelling Wave Array System as Solution for the ICRF Heating of DEMO

Travelling Wave Array (TWA) antennas distributed all along the periphery of the tokamak are presently considered as Ion Cyclotron Resonance Frequencies (ICRF) heating solution for the DEMO reactor. Compared to the conventional ICRF antenna systems currently in use or designed for future machines like ITER, the TWA consists of antenna sections integrated in the breeding blanket all around the machine, each one fed through a variable coupler in a resonant ring configuration. Modelling an antenna system for DEMO with 18 quadruple TWA sections of 8 straps shows that a power capability exceeding 60MW can be obtained in the frequency band of interest using the reference low coupling plasma profile of ITER. The described system optimizes the coupling to the plasma providing a large number of radiating elements, which results in enhanced antenna directivity, and decreasing the antenna power density. This results in a maximum strap voltage amplitude of only 15kV and maximum inter-strap voltage amplitude of 18kV. The on purpose absence of vertical septa between straps increases the performance of the TWA compared to the classical antenna layouts. The generators remain matched for all loading conditions: the system is totally load resilient. A TWA fed with a resonant ring circuit should allow having almost 100% of the generator power injected in the plasma with associated negligible damping in the dummy load of the variable coupler. The Voltage Standing Wave Ratio (VSWR) remains close to 1 for a broad range of loading resistances and frequencies. The proposed TWA system has been successfully tested on a scaled mock-up loaded by a salty water dummy load. The system tuning procedure is simple and an algorithm is under development. To assess the feasibility of the TWA fed by a resonant ring for a DEMO reactor a test on an existing Tokamak is under study.

Speaker: Mr Riccardo Ragona (Laboratory for Plasma Physics, LPP-ERM/KMS)

FEC2018_Summary_slide.pdf

684 A versatile multi-cusp plasma device for confining contact ionized alkali ions: source for the experimental studies

The confinement by multi-cusp magnetic field configuration is being revisited in prospect of developing a Negative Ion Beam source for heating the plasma in fusion devices. For this, an experimental device namely the Multi-cusp Plasma Device (MPD), has been constructed to study the physics of plasma confinement in a multi-cusp configuration. In this experiment alkali ions of low ionization potential will be produced by contact ionization and will be confined in the multi-cusp magnetic field configuration. The cesium ions will be produce by impinging a collimated neutral cesium atoms on an ionizer consisting of a hot tungsten plate. The temperature of the tungsten plate will be made high enough (~2700⁰K) such that it will also be contributing electrons to plasma. Hence the design of hot plate ionizer is very crucial. For heating the tungsten plate hot cathode technique will be used. Thermionic electron emission from tungsten plate is exponentially proportional to the temperature of the plate. A gradient of very little value in the temperature of the hotplate, might cause a large temperature gradient and hence large potential difference in plasma which will result in drift thus affecting the experiment. So it is desired to keep the hot plate temperature to be uniform within 1%. The tungsten plate is so hot that the direct contact method for the temperature measurements can’t be used. To measure the thermal contours of the ionizer hot plate non-contact method will be used and characterized.

Speaker: Mr ZUBIN SHAIKH (DEPARTMENT OF PHYSICS, SAURAHTRA UNIVERSITY, RAJKOT, INDIA)

SUMMARY .pdf

SUMMARY .pdf

685 Challenges and Solutions in the Design of RFX-Mod2, a Multi Configuration Magnetic Confinement Experimental Device

The RFX toroidal device (R – major radius=2.0 m, a - plasma minor radius=0.457 m, b - shell minor radius=0.535 m; in operation 1992-1999) was designed to be operated in Reversed Field Pinch (RFP) configuration with a plasma current up to 2 MA. RFX-mod (R=2.0 m, a=0.459 m, b=0.512 m; in operation 2004-2015) was then equipped with 192 independently driven full coverage saddle coils to achieve the full control of RWM modes and a significant mitigation of tearing modes. The mode and plasma equilibrium control innovations allowed to effectively reach the 2 MA current goal and led to the experimental confirmation of the single helical axis equilibrium of the RFP. Operation in ultra low-q (Ulq) pinch gave new insights on fundamental plasma properties. Experiments performed in circular and shaped tokamak configurations led to the first active stabilization at $q(a) \leq 2$ and recently an H-mode by electrode biasing. Such results suggested the two future main goals of RFX-mod2 (R=2.0 m, a=0.490 m, b=0.512 m), the upgrade of RFX-mod: improvement of the RFP confinement and knowledge expansion on a broad spectrum of plasma physics in regimes otherwise not accessible on other devices. The key ingredient of the new design is the enhancement of the shell-plasma proximity (b/a=1.04), expected to provide a significant reduction of the amplitude of RFP tearing modes. This reduction would lead to the positive cascade effects of magnetic chaos mitigation with confinement improvement, reduced plasma wall interaction and better mode control capability. This choice implied challenging major modifications on the components of the machine close to the plasma: removal of the present vacuum vessel and placement of the existing conducting shell in vacuum as close as possible to the plasma; the vacuum barrier would be then provided by the properly modified toroidal support structure. Innovative solutions have been conceived to fulfill vacuum and electrical requirements of the in-vessel components. Furthermore a number of corollary modifications are foreseen, aimed at widening the operational space in terms of controlled density, magnetic field topology and the diagnostic capability, in all three different magnetic configurations in the foreseen range of plasma currents: 100 kA - 2 MA RFP, 40 - 180 kA tokamak, 20 - 800 kA Ulq.

Speaker: Dr Roberto Cavazzana (Consorzio RFX)

Summary_slide_EX-P8-7_RFX-mod2.pptx

686 Characterization of advanced concepts for first wall materials by plasma exposure in the linear plasma device PSI-2

Tungsten is envisaged as plasma-facing material in fusion reactors because of its small tritium retention and low erosion rate as well as its high melting point and high thermal conductivity. However, its intrinsic and operation-induced brittleness and the unacceptably high oxidation rate at high temperatures pose challenges for manufacturing, component lifetime and safety. The development of new advanced material concepts such as new tungsten alloys and composites produced via powder injection molding, self-passivating tungsten alloys produced via field assisted sintering technology and fiber reinforced tungsten composites produced by powder metallurgy or chemical vapor deposition, may help to overcome these issues. To support a fast route for production of plasma facing components, the characterization of these advanced materials under fusion relevant loading conditions is needed. Plasma exposure in linear plasma devices under synergistic particle and transient heat loads offers the opportunity to investigate the plasma compatibility of the new material concepts at an early stage of development. In this contribution, we report on first experiments in the linear plasma device PSI-2 to assess erosion rates, fuel retention and damage thresholds of advanced tungsten based alloys and composites in deuterium and mixed deuterium-helium and argon/neon plasmas. Under these conditions, advanced material concepts based on tungsten do not show significantly degraded plasma compatibility with respect to reference tungsten material.

Speaker: Prof. Bernhard Unterberg (Forschungszentrum Jülich)

687 Characterization of Argon Plasma in a Multi line Cusp Magnetic Field: Towards a Favorable Source for NBI System

The positive or negative ion sources which form the primary component of neutral beam injection (NBI) in controlled nuclear fusion using magnetic confinement have to meet simultaneously several demanding requirement like to produce high current, high energy and low-emmitance stable H- ion sources and to confine them etc [1]. It is very well known that multi cusp magnetic fields can confine high dense plasmas [2] and thus the application of multi cusp magnetic field geometry has received a great attention in a wide range of systems viz. ion sources, plasma facing material and diagnostic testing in fusion reactors [3-4]. Apart from the fusion studies cusp magnetic fields are rigorously used in plasma etching reactors, ion thrusters, Magnetrons and also in plasma wave study experiments [2, 6-7]. A versatile Multi line cusp plasma device of axial length 1.2m and diameter 40cm has been developed in house, by using six electromagnets placed over the periphery of a cylindrical chamber. The magnetic field lines are profiled by using a core material Vacoflux-50. In this paper, by performing simulations in FEMM (Field Element Method Magnetic) [8] tools, we first show how to profile the magnetic field lines as per the requirements. Then we characterize the filamentary Argon plasma in this variable Multi line cusp magnetic field and illustrate the effect of variable magnetic field on mean plasma density, particle confinement time, leak width and size of field free region by changing the magnet current.

Speaker: Mr amitkumar patel (institute for plasma research)

688 Characterization of the W7-X Scrape-Off Layer using the Multi-Purpose Manipulator

Wendelstein 7-X (W7-X) recently concluded its first operation phase (OP1.2a) featuring an island divertor. In this concept, the heat and particle exhaust to the divertors is governed by intrinsic three-dimensional magnetic islands at the plasma edge. In order to establish high performance plasmas with safe divertor operation, a comprehensive understanding of the island divertor physics is required, for which in turn thorough studies of the plasma properties and dynamics within the islands are essential. The Multi-Purpose Manipulator (MPM), a carrier system for probe heads mounted at the outboard mid-plane of W7-X, is a key diagnostic for the characterization the W7-X Scrape-Off Layer. Being a multi-user platform, it served various scientific aspects during OP1.2a, including different electric and magnetic probes, plasma-surface interaction studies, hydrogen fuelling and impurity injection. Characterization of the SOL by the MPM mostly relies on the use of reciprocating electric probes which can perform radial fast plunges through a magnetic island up the last closed flux surface. The fundamental quantities inferred from probe measurements (e.g. radial profiles of density, electron temperature, plasma flows, electric fields and potentials) already allow to infer conclusions on the magnitude and spatial distribution of parallel heat and particle transport to the divertor. Employing, in addition, spatially distributed arrays of probes, we obtained insight into the dynamics and propagation of turbulent fluctuations and the associated (perpendicular) fluctuation-induced transport. Typical fundamental plasma parameters that have been obtained using the MPM are electron temperatures up to 100 eV and densities up to 1∙1019 m-3 with a strong dependence on operation (e.g. heating power) and core plasma parameters (e.g. density). Furthermore, the complex magnetic field topology in the large configuration space of W7-X is found to play an important role for the edge plasma profiles. Hence, cross-checks with other SOL diagnostics are used for both validation of results as well as identification of local effects (e.g. due to the island structure).

Speaker: Dr Carsten Killer (Max-Planck-Institute for Plasma Physics, Greifswald, Germany)

689 Concept of a new approach in thermographic measurements for plasma-wall interaction studies on KTM tokamak

In the paper is described concept of non-contact temperature measuring technique of metallic surface is currently being developed for KTM tokamak. Suggested technique is based on using thermographic camera and infrared carbon dioxide laser (CO2) with 10.6 micrometer wavelength. The pulsed IR laser radiation is used to observe changes in the emissivity of the body. This information will give possibility to make a correction of the thermal measurements of the thermographic camera. Preliminary experimental results of measurement technique are shown in the paper and discussed. Plans for implementation and testing of measuring technique are also discussed. The developed technique will be used for an accurate spatial measurement of the heating temperature of the metal surface of the first wall candidate materials under the influence of thermal plasma fluxes on the KTM tokamak.

Speaker: Mr Baurzhan Chektybayev (Institute of Atomic Energy of National Nuclear Center of Republic Kazakhstan)

Summary slide.pdf

690 Correlation analysis based magnetic Kubo number estimation during pedestal collapse in BOUT++ simulation

We perform a correlation analysis to explore how the magnetic Kubo number evolves during and after an abrupt edge pedestal collapse generating stochastic magnetic fields in the simulation. During abrupt edge pedestal collapse caused by type-I ELM (Edge Localized Mode), the stochastic magnetic field is thought to be a possible way to induce significant cross-field diffusion. We analyze the results obtained by the numerical simulations performed within BOUT++ framework solving a set of three-field reduced magnetohydrodynamics equations for toroidally confined plasmas. We set the equilibrium pressure gradient to be much higher than the stability limit of the initially seeded ballooning mode. The magnetic Kubo number in our simulation is found not to exceed unity. This result indicates that the quasilinear Gaussian diffusion model, not percolation theory, is adequate to explain the cross-field diffusion. Radial correlation length of pressure fluctuations is highly correlated with radial width of the stochastic magnetic fields; while time evolution of poloidal correlation length of pressure fluctuations behaves like that of Chirikov parameter and Kubo number.

Speaker: Mr Jaewook Kim (KAIST)

Evolution of magnetic Kubo number of stochastic magnetic fields during the edge pedestal collapse simulation, Physics of Plasmas 25, 082306 (2018)

Single_slide_Jaewook_v1.pdf

691 Design and Development of Control Grid Power Supply for RF Amplifier

ITER require 20 MW of RF power to a large variety of plasmas in the Ion Cyclotron frequency range for heating and driving plasma current. Eight RF sources of 2.5MW RF power level each collectively will accomplish the above requirement. Each RF source consists of Solid State Power Amplifier (SSPA), driver, and end-stage, above which driver and end-stage amplifier are a tube (Tetrode/Diacrode) based which require DC power supplies viz. Anode, filament, screen grid, and control grid DC power supply. DC power supply has some stringent requirements like low stored energy, fast turn off, and low ripple value, etc. This paper includes a detailed study of Zero Voltage Switching (ZVS) resonant converter based buck converter, understanding with the help of mathematical equations of its various modes, simulation of the design in PSIM software and power supply development. The Control grid of RF tube needs a negative biased DC power supply which would be operating in three modes of operation namely viz. i. Cut off mode (-500V, 10A), ii. Conduction mode with no RF power extraction (-350V, 7A) and iii. Conduction mode with RF power extraction (-350V, 2A to 7A). Depending upon the application, it needs to fulfil the requirement of constant voltage variable current when operating in conduction mode with RF application. A 500V, 10A modular DC power supply has been developed and tested on resistive load; it has four modules of 125V, 10A each in series for obtaining 500V at the output with 1% peak to peak ripple voltage in the output and stored energy well within the limit. The power circuit of each module consists of 6 pulse rectifier unit with DC link capacitor followed by resonant buck converter with switching frequency of the IGBT switch is of the order of 20 kHz.This paper addresses the analysis, design and hardware implementation of CGPS for Diacrode based system.

Speaker: Mr Kartik Mohan (ITER-India,IPR)

692 Design and Simulation of Circular Waveguide Elbows Applicable in High Power Microwave (HPM) Coupling to Plasma

SYstem for Microwave PLasma Experiments (SYMPLE) is an experimental system set up at the Institute for Plasma Research (IPR), Gandhinagar, India, to investigate the physics of linear and nonlinear interaction of high-power microwave (HPM) with plasma. BWO based HPM source, proposed to be used for these studies, generates pulsed (~50 ns) microwave power of ~500MW at 3GHz frequency in TM01 mode. The BWO output power is extracted via an oversized circular waveguide of radius 15 cm. A transmission system is required between the HPM source and the plasma in order to couple the HPM power to plasma and to carry out measurements of forward and reflected microwave power. This transmission system will need a few elbows which can maintain same operating frequency, power level and propagating mode. Understanding of HPM compatible waveguide elbows assumes further significance due to their applications in modern HPM systems in general. In the design of waveguide elbows, two considerations are of foremost significance. One is the minimization of the return loss as well as maintainability of mode purity in a frequency band as wide as possible and the other is the minimization of the size of the elbow. Various configurations of elbows have been subject to analysis by the solver, CST Microwave Studio, for efficient transmission of power while maintaining the operating frequency and propagating mode. Irrespective of the shape of elbows used, those with gradual bends have been found to perform better compared to 90 elbows, in terms of power loss and frequency/mode shift. Further, of the various configurations studied, Z-shaped, L-shaped, U-shaped and Pi-shaped elbows are found to perform relatively better. Performance of circular waveguide elbows having configurations discussed above has been studied in detail in the present work. Observations show that, at 3 GHz frequency, U-shaped elbow shows good power transmission and reflection but not mode purity while others show either poor or average transmission. Pi-shaped elbows, however, maintains TM01 mode but not power. Choice of the elbow configuration for any particular application should therefore depend on the requirement, i.e. having the minimum power loss, or having the frequency or mode retained. A detailed account of the design, simulation and analysis of various elbow configurations is presented in this report.

Speaker: Dr Jitendra Kumar (Institute for Plasma Research)

Key Achievements.pdf

693 Development and Validation of Cryostat Finite Element Model with Unique FE Method

The ITER Cryostat, the largest stainless steel vacuum pressure chamber ever built which provides the vacuum confinement to components operating in ITER ranging from 4.5 k to 80 k. Cryostat Design Model was qualified[1] by ITER. As a Safety Important Class system, Design qualification at every change in its development and installation phases is mandatory. The Cryostat system is currently at manufacturing stage, several Deviation request are being reported e.g. tolerances change, ribs modification etc. These changes affect the behavior of Cryostat which needs re-assessment. The conventional design approach in Finite Element method (FEM) needs significant time and effort, as incorporation of changes calls for redevelopment of full mathematical model.
In this paper a “unique method” of developing FE model for complex systems like Cryostat is presented, which typically addresses above need and the method is qualified with results of Cryostat engineering model (CEM) [1,2]. This unique method involves dividing and meshing of the big components in to sub components, so the full Cryostat is divided into 30 sub components and mathematical models of these individual components are developed. These sub components are integrated using suitable constraint equations to create full FE model [3,4]. Then the integrity of model is assessed using the modes shapes. This unique method enables to incorporate component level changes without affecting the full FE model, thus saving time and efforts of re-development of mathematical model.
For qualification of developed FE model category II loading and selected load combinations are applied. The results obtained are in close approximation with CEM results [1,2]. As the present need was to address the changes of manufacturing model, so further Cryostat manufacturing FE model (CMM) is developed with this unique approach. It is then analyzed for category II loading and selected load combination.
This paper gives detailed insight about the developing and qualification of the Unique Method and details of the analysis results of CMM.
References
[1]ITER Cryostat—an overview and design progress, Fusion Engineering and Design 86(2011)
[2]The structure analysis of ITER Cryostat based on the FEM, Fusion Engineering and Design 88(2013)
[3]Instructional Material Complementing FEMA 451, Design Example, SI- 15-7-53
[4]ANSYS ref.

Speaker: Mr TARUN KUMAR SHARMA (ITER-India, Institute for Plasma Research)

Summary slides_Development and Validation of Cryostat Finite Element Model with Unique FE MethodFIP P8-22.pptx

694 Development of Indigenous Electrical Insulation Breaks for Superconducting Magnets of Fusion Devices

Electrical insulation breaks are very critical component of large-scale fusion devices employing superconducting magnets. The electrical insulation breaks developed for the requirement of up gradation of hydraulics for the superconducting polodial field coils (SC) of SST-1 fusion machine. The electrical insulation breaks have been installed in the hydraulic, validated and sustained the operational required temperature. It has performed in rigorous environment of many thermal cycling from 300 K to 4. 2K of pressure 1-12 bar which induced more thermal stress in electrical insulation breaks. Main function of such insulation break is to supply cold helium to SC magnets and to isolate the magnets electrically from ground potential during the quench. The salient design features include bigger dimension of ½” size, break-down voltage to 5 kV, helium leak tightness ≤ 1 x 10-8 mbar-l/s at 4.5 K and needless to mention the cryogenic compatibility and flexibility issues. Success rate is about 75 % as it is new attempt with indigenous epoxy resin system. The basic structural materials are SS 316L feed tube separated by a cryogenic grade G10 GFRP insulation material which bonded with cryogenic epoxy resin. The failures causes have been identified, analyses that considered and rectified during indigenous development of electrical insulation breaks.The failure was observed after the repeated 4.2 K cryogenic cycles which doubts the reliability of component and epoxy resin system. The real research & development as well as challenge are to define and develop an adequate cryo compatible epoxy. The electrical insulation breaks and cryogenic epoxy resin are not commercially available items, not reliable, cost factor and failure was noticed after cold thermal cycles. The In-house indigenous developed electrical insulation breaks can be used for future indigenous superconducting magnet fusion machines, electrical isolation and for low temperature experiments purpose (up to 15 kV applications), bonding and sealing of dissimilar materials at cryo temperature with very much cost effective. In this paper, the design, development, fabrication, performance test at 300 K, 77 K and 4.2 K of electrical insulation breaks and highlight on development of indigenous cryogenic epoxy resin system will be presented.

Speaker: Mr Rajiv Sharma (Institute for Plasma Research (An Autonomous Institute under Department of Atomic Energy,Govt. of India))

summary slide _Rajiv Sharma_FIP -P8-12.pdf

695 Development of Solid State Power Amplifier for ICH & CD RF Source

ITER-India is developing Ion Cyclotron Heating & Current Drive (ICH&CD) RF source in the frequency of 35 to 65 MHz. Three cascaded amplifiers along with low power RF section, AC/DC power supplies and controls will be used for getting MW level RF power from one source. In the present configuration, two tube based tuned amplifiers, i.e. driver (150 kW) and final (1.7 MW) stage amplifiers are driven by a 10 kW wideband solid state power amplifier (SSPA). Development of such SSPA with required 1.5 dB gain flatness in the above frequency range is very challenging, due to unique design of combiner and output matching circuit. This development is also aiming for achieving compact modular design, higher efficiency, usage of low voltage power supplies and better MTBF value compared with tube based amplifier of similar specification. Since 8 kW is needed as input power to the driver stage amplifier, the design goal for SSPA is to achieve power level of around 10 kW/CW. Multiple pallet amplifier modules having capability of 1 kW are to be combined to achieve desire output. Pallet amplifier module is designed using LDMOS transistors (MRFE6VP61K25H), which is capable to deliver 1000 W CW power in the required frequency range with adequate tune matching circuits. For input matching 9:1 ferrite based balun is used. For output circuit, 1:9 impedance transformation & balance to unbalance quarter wave transformer is used. For gate and drain supply voltages, adequate filters are designed and installed. In this paper, detail design and development of single pallet amplifier module as a part of wideband Solid State Power Amplifier will be discussed along with test results. This paper also include integration and testing of 4 pallet amplifier modules using 4 way power splitter and combiner. Control & monitoring of SSPA will be discussed in brief. Further, upcoming plan for integration of 16 such pallet modules with controls and monitoring system will be discussed. REF: [1] LDMOS transistor Datasheet, http://www.nxp.com/products/rf/rf-power-transistors/rf-industrial-scientific-and-medical/1.8-600-mhz-1250-w-cw-50-v-wideband-rf-power-ldmos-transistors:MRFE6VP61K25H [2] Aparajita Mukherjee et. al., Progress in High Power Test of R&D Source for ITER ICRF system, 26th IAEA FEC 2016, 17-22 Oct 2016, Kyoto, Japan

Speaker: Mr MANOJKUMAR PATEL (PATEL)

696 Development of Various diagnostics for NNBI program in IPR

The characteristics of a negative hydrogen ion (H-) source and its neutralization mainly determine the performance of a negative ion based neutral beam injector (NNBI) performance. Ion source possesses many technological challenges in terms of production of uniform, extracted and accelerated negative ion beam current and also its transport to the tokamak plasma or the beam dump without damaging the beamline components during its transit. Therefore, for safe operation and also to characterize the beam, it is necessary to monitor the performance of the ion source and the beam. A judicious choice of various diagnostics comprises of optical, electrical, calorimetric and thermal are required. For that a number of diagnostics are being developed for NNBI R&D program. Indian Test Facility (INTF) is an integral part of this program. Due to having versatility in nature, independent prototype experimental efforts have been carried out to establish different diagnostics. For ion source plasma characterization, optical emission spectroscopy (OES), cavity ring down spectroscopy (CRDS) and electrical probe (EP) are mainly envisaged apart from different electrical measurements in RF circuit. All are either implemented in ROBIN source in prototype setup. Regarding beam characterization, Doppler Shift Spectroscopy (DSS), Optical Emission Tomography (TOMO), Infra-red (IR) thermal imaging on carbon fiber composite (CFC) target plates in addition to thermocouple based calorimetric diagnostics on different beam line components along with electrical measurements in the accelerator power supply circuits and residual ion deflection (RID) circuits are planned. The DSS system with eight lines of sight (LOS) (blue-shifted and red-shifted) is already implemented in ROBIN ion source. An algorithm for TOMO and the corresponding code based on maximum entropy concept is developed to reconstruct the 2D emissivity profile which is obtained from the inversion of the LOS integral of brightness. The code has been tested using mathematical functions representing simulated INTF beam profile. In the paper present status of various diagnostics for ion source and beam characterization, in terms of its designs, characterization algorithms, results either on separate prototype or on associated operational ion source testbed will be presented.

Speaker: Dr BANDYOPADHYAY MAINAK (ITER-INDIA, INSTITUTE FOR PLASMA RESEARCH)

FEC Mainak-Diagnostics Poster-preprints-V1.pdf

Summary Slide – FEC2018 Mainak-Diagnostics.pdf

697 Development of wideband amplifier in ITER ICRF range

ITER-India is responsible for delivery of 8+1(prototype) RF sources to ITER project. Each RF source will provide 2.5MW of RF power at VSWR 2:1 in the frequency range of 35 to 65MHz. Eight such RF sources will generate total 20MW of RF power. Two RF chains containing three high power amplifiers (HPA1, HPA2 and HPA3) need to be combined to build an RF source. HPA2 and HPP3 are RF tube based amplifiers while HPA1 is a solid state power amplifier. A development work is ongoing for a tetrode tube based wide band HPA1. Aim is to achieve a -1dB bandwidth over any 5MHz band in frequency range 35-65MHz. To achieve this specification the design of output cavity is based on wideband impedance matching circuit. Two L-C circuits connected in series are tuned to achieve a wideband response over desired frequency band. Input circuit design is based on tunable wide band impedance transformer. The amplifier is designed to operate in Grounded Grid configuration with CPI 4CW25000B tube. The rated output power is 10kW/CW. A detailed calculation is performed to find operating parameters of tetrode tube at rated power. A LabVIEW based code Tetrode Tube Calculator (TTC) is developed to perform load line calculation for tetrode tube. The code requires as input, parameters like DC anode bias, input DC power, anode voltage swing etc. and calculates the parameters like output power, efficiency, output impedance, input impedance etc. The calculated parameters are used as input for cavity design. This paper discusses the tube parametric calculation using TTC code in detail. The detailed design of HPA1 cavity using CST Microwave studio software is discussed.

Speaker: Mr AKHIL JHA (ITER-INDIA, INSTITUTE FOR PLASMA RESEARCH)

Summary_DEVELOPMENT_OF_WIDEBAND_AMPLIFIER_IN_ITER_ICRF_RANGE.pdf

698 Effect of poloidal density asymmetries on shear flows and radial electric field at the plasma edge

In the simplest, magnetohydrodynamic (MHD) description of the plasma equilibrium, rapid transport along the field lines leads to a state where the plasma density and temperature are constant on flux surfaces, exhibiting symmetry in both the poloidal and toroidal directions. This idealization, however, breaks down at the plasma edge where both the magnetic topology and various perpendicular transport processes introduce at least a poloidal asymmetry. We show that the mass flows and radial electric field driven by edge poloidal density asymmetries can be used as a highly effective control mechanism for the edge and thus the global confinement in tokamaks. The underlying physics can be demonstrated entirely within a simple magnetohydrodynamic equilibrium model with an appropriate flow damping mechanism. As an example, strong dependence of the low to high (LH) transition power threshold on the magnetic topology, an experimental observation still poorly understood, can be easily explained within this framework. Similar arguments also indicate that some of the ITER fueling ports are misplaced from an operational point of view and may lead to higher input power requirements.

Speaker: Dr Ahmet Y. Aydemir (National Fusion Research Institute, Daejeon, Korea)

summary.pdf

699 ELM-induced energy and momentum transport in ASDEX Upgrade

Heat and momentum transport play a key role in achieving high confinement in fusion plasmas. Recent advances in the diagnostic capabilities at AUG now allow us to measure the edge profiles on a sub-ms to ms time-scale and with a spatial resolution of less than 5 mm, making it ideal to study the profile recovery after an ELM crash. Here, we present the dynamic behaviour of the energy and momentum transport during edge localized mode cycles at the plasma edge of AUG by combining a comprehensive set of pedestal measurements with interpretive and predictive modelling. The main ion temperature and toroidal rotation profiles were measured in helium plasmas with unprecedented temporal resolution of 250 mus. A local increase of Ti close to the separatrix is observed at the ELM onset, thus reducing the gradient in the pedestal, similar to the behaviour in D plasmas [1]. Shortly after the initial separatrix increase, the whole profile drops and then the pedestal starts to build up again. The pre-ELM profile is fully recovered 3-4 ms after the ELM crash. Transport analysis of the ion energy reveals that the ion heat transport is at the neoclassical level before the ELM crash in the region where the edge ion temperature gradient is maximal. Further inwards, the ion heat transport is about a factor of 4-5 above the neoclassical level. The dynamics of the edge ion heat transport during the pedestal build-up after the crash is also consistent with neoclassical theory [2]. Helium plasmas provide the unique opportunity to measure both main ion and impurity flows simultaneously. Compared to the impurity (here nitrogen) toroidal rotation, which exhibits a local minimum at the plasma edge during the inter-ELM phase [3], the edge main ion toroidal rotation has a much less pronounced dip and is rather flat. During the ELM the main ion toroidal rotation in the pedestal drops by about 5-10 km/s. This is in contrast to the behaviour of the impurity toroidal rotation, which shows a flattening of the toroidal dip feature [1]. TRANSP simulations and predictive modelling with ASTRA solving the toroidal momentum balance including diffusion, pinch and external sources are used to quantify how much momentum is transported during the ELM and will be presented. [1] M. Cavedon et al PPCF 59 105007 (2017) [2] E. Viezzer et al NF 58 026031 (2018) [3] T. Pütterich et al PRL 102 (2009)

Speaker: Dr Eleonora Viezzer (University of Seville)

elv_summary_slide_iaea2018.pdf

700 Energy Confinement and Performance of Pure Helium Plasmas and Helium Seeded Deuterium Plasmas

The presence of fusion-produced helium is fundamentally connected to the performance of a fusion reactor. Not only will He ash dilute the fusion fuel if not removed promptly, but the presence of He in a D plasma is reported to negatively affect the plasma confinement [1]. Furthermore, He plasmas are a choice for the ITER non-nuclear phase, but the energy confinement in such plasmas is consistently observed to be ~30% lower than in D plasmas [2, 3]. The negative impact on the performance observed with reactor relevant concentrations of He in D plasmas is demonstrated and compared in baseline scenario plasmas in JET and in plasmas with and without N-seeding in ASDEX Upgrade (AUG). In both devices, a significant reduction of the plasma stored energy (and normalised confinement factor H98(y,2)) is observed with increasing He concentration. Helium impacts the edge and core plasma profiles in a phenomenologically similar way in the two machines, and also affects the ELM behavior, and the produced neutrons. However, both the core and edge contribute to the loss of stored energy at AUG, while the core alone is responsible for the loss of stored energy at JET. In both JET and AUG, after applied short He puffs, the confinement is observed to recover at the same rate as the He concentration decays. Additionally, the confinement of pure He plasmas at AUG is studied, demonstrating plasma conditions where confinement in He is the same as in D plasmas. Pairs of L- and H-mode plasmas in He and D have been produced, in which a large variation of the electron to ion heating fraction is obtained using the ECRH and the NBI systems. Two regimes are identified. With strong ECRH and low electron density, the confinement in He is equivalent to that in D. With strong NBI heating, there is a significant degradation of the confinement in He (~70% of the corresponding D plasma). These observations are theoretically explained. In the core, the stronger impact of zonal flows in ITG turbulence as compared to TEM turbulence breaks the gyro-Bohm scaling in the strong NBI case. At the edge, thermal coupling and the destabilization of ETG modes in He prevent the increase of the ion and electron temperatures. [1] R. Neu et al, Proc. 35th EPS Conf. (2008), [2] F. Ryter et al, Nucl. Fusion 49, 62003 (2009), [3] D.C. McDonald et al, Plasma Phys. Control. Fusion 46, 519 (2004)

Speaker: Dr Athina Kappatou (Max-Planck-Institut für Plasmaphysik, Garching, Germany)

Kappatou_IAEA2018_summary_slide.pdf

701 Energy loss and pitch angle scattering of runaway electrons due to kinetic instabilities

The effects of kinetic instabilities on the dynamics of runaway electrons in momentum space is investigated using a newly-developed simulation model, and the anomalous dissipation and the fast pitch angle scattering of runaway electrons in low energy are explained. The interaction of runaway electron avalanche and the kinetic instabilities are studied self-consistently using quasilinear model. Results show that excited whistler waves can cause runaway electrons to be scattered to large pitch angle and form vortices in momentum space, creating a new energy loss channel, which explains the higher-than-expected critical electric field and the loss of runaway electron population in low energy regime identified experimentally. This finding also explains the fast growth of electron cyclotron emission (ECE) signals observed in experiments.

Speaker: Chang Liu (Princeton Plasma Physics Laboratory)

summary-slide-TH-P8-16.pdf

702 Evolution and Implementation of Loss-Less Data Acquisition for Steady State Tokamak

The evolution of data acquisition system (DAS) for steady-state operation of Tokamak has been technology driven. Steady-state Tokamak demands a data acquisition system which is capable enough to acquire data losslessly from diagnostics. The needs of loss less continuous acquisition have a significant effect on data storage and takes up a greater portion of any data acquisition Systems. With the expected long discharge duration from the variety of fast and slow diagnostics, the challenge is also to cater the need of a real time monitoring of signals by multiple locally networked users.So there is strong demand for something that would control the expansion of both these portion by a way of employing compression technique in real time. With these objectives, the DAS is based on a model where the objects of the systems are integrated with the Central Control System of SST-1 using the TCP/IP communication. The DAS software essentially meets the demand of an active remote configuration of hardware digitizers, like PXI system and that of the initialization of acquisition within the local network. The present work describes the evolution of TCP/IP based DAS software in Labview for configuring, acquiring, and subsequently, pushing the sampled data into network. It presents a model of data acquisition system employing real-time data compression technique based on LZO. It is a data compression library suitable for data compression and decompression in real time. The algorithm used favours speed over compression ratio. The compression/decompression system has been rigged up based on PXI bus and dual buffer mode architecture is implemented for loss less acquisition. The acquired buffer is compressed in real time and streamed to network and hard disk for storage. Observed performance of measure on various data type like binary, integer float, types of different type of wave form as well as compression timing overheads. Various software modules for real-time acquiring, online viewing of data on network nodes have been developed in Labview & LabWindows/CVI based on client server architecture. The focus will also be on the recent first phase operations of SST-1 in short pulse mode which have provided an excellent opportunity for the essential initial tests and benchmark of the SST-1 Data Acquisition Systems.

Speaker: Mrs Manika Sharma (Institute for Plasma Research)

FIP-F8-25-manika.pdf

703 From RFX-mod to RFX-mod2: perspectives of the Reversed Field Pinch configuration

In this contribution the main achievements of the RFX-mod Reversed Field Pinch (RFP) are summarized as the basis for a substantial upgrade of the device. The RFX-mod active MHD control system successfully controlled MHD instabilities such as Resistive Wall Modes and mitigated localized Plasma Wall Interaction by avoiding Tearing Modes wall-locking. This allowed producing the highest RFP plasma current in the world, up to 2MA. At high current the RFP plasma, as predicted by the theory, has been observed to self-organize in a global helical shape, where one Tearing Mode dominates the spectrum. In such regimes secondary Tearing Modes still play a role, influencing both internal transport and recycling, impurity content and density limit, through the non axi-symmetric distortion of the plasma edge. Passive and active boundary structures surrounding the plasma have a significant effect on Tearing Modes: the RFXLocking code has been developed to describe such an interaction in RFX-mod and to investigate RFX-mod limitations, thus indicating possible improvements of the device. A further reduction of secondary modes is only possible by reducing the plasma - stabilizing shell distance and lowering the resistivity of the first conducting wall surrounding the plasma. Both these requirements are met in the design of the upgraded device (dubbed RFX-mod2) by removing the present vacuum vessel and modifying the support structure to ensure vacuum tightness. This is expected to reduce the edge magnetic deformation, thus improving PWI and confinement. Non-linear visco-resistive MHD simulations with a boundary layout that mimics RFX-mod2 are reported, in order to better quantify the reduction of the non-linearly saturated amplitude of tearing modes. Some technological issues raised by the implementation of the new magnetic boundary are also discussed

Speaker: Dr Lionello Marrelli (Consorzio RFX)

Summary Slide Summary_slide_EX-P8-6_RFX-mod2_v2.pptx

704 Gyrokinetic Neoclassical Study of the effect of the X-point height on ExB Flow Structure in an H-mode edge plasma

The X-point height relative to the divertor plates may cause difference in the neutral particle penetration into pedestal and have impact on the pedestal physics in H-mode. In the present work, we utilize the total-f global gyrokinetic neoclassical code XGCa to study the X-point height effect on the ExB flow profile in a JET-like H-mode pedestal in a realistic JET-like divertor geometry and with neutral particle recycling. The vacuum pump is not modeled in the results presented here. Effect of plasma turbulence on the Er-well depth is not considered either. The main result is that the neoclassical Er profile is sensitive to the vertical X-point location, while the plasma profile change is only minimal. The findings here imply that, even though the change in the plasma profile may not be easily noticeable in the experiment, the hidden change in the ExB profile could cause a difference in the pedestal physics such as the ELM stability and turbulent/neoclassical transport. The change in the ExB rotation, without much change in the plasma profiles, is balanced by the change in the toroidal flow speed. The vertical X-point movement, as a result of this Er profile change, can sensitively affect high-Z impurity transport and its accumulation in the pedestal.

Speaker: Dr Jugal Chowdhury (Princeton Plasma Physics Laboratory, Princeton, NJ 08543-451, USA)

summary_slide_JChowdhury.pdf

705 Heat transport driven by the ITG and TEM instabilities in the ASDEX Upgrade tokamak

Turbulence-driven ion heat transport in tokamak H-modes is driven by the ion temperature gradient (ITG) instability, while electron heat transport is driven by the ITG, trapped electron mode (TEM) and/or electron temperature gradient (ETG) instabilities. These three instabilities appear above their respective threshold in normalized temperature gradient (R/LT) and drive transport. We present results on the role of these contributions to heat transport in the ASDEX Upgrade tokamak. We performed dedicated experiments with neutral beam injection (NBI) which heats both electrons and ions and electron cyclotron resonant heating (ECRH) which heats the electrons. From modulating of the electron temperature with ECRH we deduce the electron heat pulse diffusivity (chi_HP) which reflects the stiffness directly and is complementary to the power balance diffusivity (chi_PB). The predicted dependences of the ITG-driven ion heat transport on Ti/Te and ExB rotational shear are found: the ITG is clearly more stable for high values of Ti/Te and/or rotational shear. The ITG threshold itself could not be assessed experimentally with accuracy yet and experiments are foreseen in the near future to improve this situation. The electron heat flux is partly driven by the ITG, but when increasing the electron heat flux with ECRH above the flux driven by the ITG, the TEM and/or ETG instabilities become unstable which is particularly visible in the modulation data. Indeed, a moderate increase of chi_PB and a stronger increase of chi_HP above R/LTe = 5 indicates unambiguously that an electron instability (TEM or ETG) develops above this threshold. The stiffness is close to that found in ASDEX Upgrade for TEM-driven electron heat transport. Below the threshold, chi_HP and chi_PB exhibit about the same value of 1.5 m2/s. This rather high value is attributed to the ITG-driven electron heat transport, in agreement with chi_HP = chi_PB which reflects the fact that the ITG does not depend on grad(Te). So far, we have found no indication of an ETG contribution predicted to exhibit a stronger stiffness. Transport modelling and comparisons of the experimental results with gyro-kinetic calculations will be presented for both the ITG and TEM/ETG studies.

Speaker: Dr Francois Ryter (Max-Planck-Institut fuer Plasmaphysik)

Ryter_iaea18_summary.pptx

706 Helical plasma-wall interaction in the RFX-mod: effects of high-n mode locking

The edge of toroidally confined plasmas can be characterized by the presence of magnetic perturbations (MP) with helicity m/n, with m and n the poloidal and toroidal mode numbers, respectively. In the Reversed Field Pinch (RFP) RFX-mod device (R=2m, a=0.46m), in high-current discharges (Ip>1MA, n/nG<0.3), an almost monochromatic magnetic spectrum spontaneously develops, with m/n=1/7 the dominant mode rotating at a toroidal frequency of ~20Hz. This mode produces a helical equilibrium called quasi-single helicity (QSH). In this new equilibrium, which stands apart from the standard, chaotic RFP state, also the shape of the edge plasma is influenced, with a helical 1/7 plasma wall interaction (PWI). Were the QSH perfectly monochromatic, the edge would show a helical scrape-off layer (SOL) with good confinement properties, as shown in previous works on RFX. Unfortunately, the QSH is disturbed by the presence of high toroidal harmonics with 7 < n < 20 (“secondary modes”). These secondary modes, with amplitude one order of magnitude smaller than the dominant n=7 one, interact each other with a constructive interference, called mode or phase locking: the result is a local radial magnetic deformation sec that can be comparable to the dominant one, 1/7, due to the 1/7 mode. From the point of view of particle transport, the presence of the phase locking translates in a localized decrease (“hole”) in the helical pattern of the connection length to the wall: Lcw. This happens because magnetic field lines, in the vicinity of the locking, are deformed in large poloidal lobes (homoclinic tangles) hitting the plasma-facing components (PFCs), a mechanism similar to the toroidal “fingers” observed in tokamak divertors during RMP application.
A smoother magnetic boundary is expected in the upgraded RFX-mod, where the magnetic deformation decreases by a factor 2-3. Initial estimates show that the local “hole” of Lcw should be strongly reduced by halving the secondary mode amplitude: this is a promising perspective for the RFP helical state performance.

Speaker: Dr paolo zanca

Scarin_Summary_Slide_EX_P8-14 .pdf

707 High density and high performance operation with pellet injection in W7-X

In this contribution we present details of recent W7-X pellet injection experiments and discuss properties of the achieved plasmas. Hydrogen pellet injections allowed to raise the electron density above $1.2 \cdot 10^{20}$ m$^{−3}$ and to establish: (i) operation above the cut-off for the X2 polarization of the 140 GHz electron cyclotron resonance heating (ECRH); (ii) stable divertor heat flux detachment; (iii) plasmas with the diamagnetic energy above 1 MJ. In the latter case, a series of pellets raised the electron density to almost $10^{20}$ m$^{−3}$ in a hydrogen discharge heated by X2 ECRH with the total power stepped from 2.7 MW to 5 MW. These electron densities are sufficiently high for electron and ion temperatures to equilibrate and to cause a change in the radial electric field. In the reheat phase after the pellet injection, ion temperatures above 3.5 keV could be reached with the ECRH only and a significant plasma pressure is achieved. The volume averaged $\left<\beta\right>$ is about 1%, whereas the peak value $\beta_0$ is about 3.5%. The diamagnetic energy of about 1.1 MJ corresponds to confinement times above 0.2 s. In the middle of the high energy phase, a sudden crash by about 150 kJ is observed by a number of diagnostics, with an inversion radius present in the ECE and soft X-ray signals. These $\beta$ values allow for the first time the analysis of the MHD stability and the validation of the Shafranov shift optimization. High central $\beta$ values are also required for the improved confinement of fast ions. A further improvement of the plasma performance can be achieved by a further increase of the electron density, which requires ECRH heating in the O2 polarization, as the electron densities are already close to the X2 cut-off. To use the full available ECRH power of 7 MW in the O2 polarization a scenario with a switch of the polarization during the discharge has to be implemented. Such a scenario was successfully tested with initially helium target plasma, because of an easier density control. The hydrogen pellet injection was used to raise the density above the X2 cut-off and to maintain it at this high level for more than half a second. In the second half of the campaign such a scenario will be attempted for hydrogen target plasmas.

Speaker: Mr Sergey Bozhenkov (Max-Planck-Institut für Plasmaphysik, Greifswald, Germany)

boz_summary_slide.pdf

708 High Power Helicon Antenna Design for DIII-D

R.C. O’Neill1, M. Brookman1, J.S. deGrassie1, B. Fishler1, M. LeSher1, C. Moeller1, C. Murphy1, A. Nagy2, M. Smiley1, J. F. Tooker1, H. Torreblanca1

1General Atomics, PO Box 85608, San Diego, California 92186-5608, USA
2 Princeton Plasma Physics Laboratory, Princeton NJ 08543, USA

Corresponding author: oneill@fusion.gat.com

A new current drive system is being designed and fabricated for the DIII-D tokamak to drive current in high beta discharges, using electromagnetic helicon waves. The high power helicon antenna (HPHA) is expected to couple 1 MW of power into the DIII-D plasmas at a frequency of 476 MHz without degrading the plasma characteristics or introducing metal impurities. This high power traveling wave antenna array is expected to have higher efficiency in driving current than other typical tokamak systems. The HPHA is a 30 CuCrZr module array mounted on a series of back plates. The modules inductively couple and resonate with the adjacent module. The two end modules are connected to a dual inner conductor strip-line transmitting RF power to and from four, 15 cm dia. vacuum coaxial feed-throughs located at the two DIII-D upper vessel ports. The modules, pitched 15˚ to follow the magnetic field lines of the tokamak, are bolted to 6 water cooled back-plates which are mounted on pedestals welded to the vessel wall. A description of the design and analyses of the HPHA and the RF strip-line feeds with anticipated overall antenna performance is presented.

This work is supported by DOE under DE-FC02-04ER54698.

Speaker: Mr Raymond O'Neill (General Atomics)

Oneill IAEA Summary Slide .pdf

709 Highly collisional two-fluid and gyrokinetic simulations of tokamak edge turbulence and the transition between kinetic and fluid regime

Gyrokinetic and non-local fluid codes have complementary limitations in the tokamak edge. To arrive at a common basis, the gyrokinetic code CGYRO and the non-local two-fluid code NLET have both been applied to identical parameters sets ranging from resistive ballooning turbulence - approaching the collisional fluid limit - relevant to the edge of a tokamak, up to high-gradient kinetic ITG modes at higher temperatures in the core-edge transitional regime, yielding comparable results. As a non-trivial, novel result, linear growth rate and nonlinear transport agree between the codes in the fluid limit of high collision numbers (nu_e~500-10000 c_i/R), not least, because the kinetic code employs the Sugama collision operator with momentum and energy conservation, Galileian invariance and exact self-adjointness property.

Speaker: Dr Klaus Hallatschek (Max-Planck-Institute for Plasma Physics)

710 Impact of an edge resonant transport layer on fast-ion confinement in the ASDEX Upgrade tokamak

An edge resonant transport layer has been found to explain many aspects of fast ion confinement under symmetry breaking 3D edge perturbations, such as edge localized modes (ELMs) and externally applied magnetic perturbations (MPs). Experimental measurements in the ASDEX Upgrade (AUG) tokamak show that fast ion losses in the presence of symmetry breaking 3D fields strongly depend on the poloidal spectra of the applied MPs. This fast ion transport is explained in terms of a resonant interaction between the perturbative fields and the particle orbital frequencies, which leads to the build up of an Edge Resonant Transport Layer (ERTL) in the vicinity of the separatrix. Full orbit simulations including the plasma response have been performed to characterize the ERTL by means of the variation in the particle toroidal canonical momentum. The combination of the poloidal spectra of the applied MPs and the relative phase of the particles with respect to the perturbation determines the radial direction of the fast ion transport, therefore degrading or improving the fast ion confinement. Consequently, an appropriate arrangement of the heating systems and externally applied 3D fields provides an excellent tool to tailor the fast ion distribution, thus modifying the drive and damping of electromagnetic instabilities through local wave particle interactions. In this regard, proof of principle experiments have been conducted in AUG, where NBI driven toroidal Alfven eigenmodes (TAEs) were excited and suppressed on command using this technique. The importance of the ERTL is extended to ELM induced fast ion losses, during which acceleration of beam ions has been recently observed in AUG. Multiple velocity space structures are observed to vary with the beam source and q95 values. This suggests that the acceleration results again from a resonant interaction between the beam ions and parallel electric fields arising during ELM filament eruption. The experimental results presented here may shed light on the physics underlying fast ion confinement in the presence of both self generated and imposed edge 3D perturbations. In the case of externally applied MPs, experiments have demonstrated the possibility of actuating on limited phase space volumes of the fast ion distribution to actively control TAEs, which is of great interest for future burning plasma experiments like ITER.

Speaker: Mr Joaquin Galdon-Quiroga (University of Seville)

GaldonQuiroga_EXP8-26_summary_slide.pdf

711 Impact of impurity seeding on pedestal structure in ASDEX Upgrade and Alcator C-Mod

Pedestal data from ASDEX Upgrade (AUG) and Alcator C-Mod are presented. Scans of impurity content have been performed in both machines, reaching states where the outer divertor is partially or fully detached. The impact of impurity seeding on pedestal structure is compared. In the analysed scenarios, nitrogen seeding increases the achievable pedestal top pressure in AUG, while excessive seeding leads to a decrease of the pedestal pressure in C-Mod as the outer divertor progresses to a fully detached state. Both of these effects are associated with a shift of the peak edge density gradient location; an inward shift (AUG) allows a higher pedestal pressure, while an outward shift (C-Mod) decreases the stability limit. The origins of these shifts are analysed in both machines, paying particular attention to the role of the SOL and the radiation associated with impurity seeding. Data from AUG highlight the importance of high density structures in the high-field side SOL in influencing the peak density gradient location, while the degradation in the C-Mod scans is independent of such a structure. This implies that mitigating these high density structures does not guarantee optimal pedestal and global confinement. Additional scans from AUG altering the heating power, seeded impurity and magnetic geometry (lower single null and quasi-double null) are also presented, demonstrating the dominating effects that the SOL can have on the pedestal. Pedestal modelling using the SOL boundary conditions from experiments is also presented, helping to form an understanding of the leading processes affecting pedestal stability.

Speaker: Dr Mike Dunne (IPP-Garching)

summary_slide_mdunne.pptx

712 Impact of the 3D geometry from non-axisymmetric magnetic perturbations on the local edge stability in ASDEX Upgrade

One method to mitigate or even suppress the repetitive impulsive energy loss due to edge localised modes (ELMs) is the application of externally applied non-axisymmetric magnetic perturbation (MP)-fields. In high confinement mode (H-mode) plasma, these externally applied MP-fields excite marginally stable ideal kink modes at the edge, which amplify the MPs. These kink modes cause a helically symmetric displacement of the plasma boundary, which amounts to ≈ 1 cm in ASDEX Upgrade [1]. Their amplitude correlate with the mitigation as well as suppression of ELMs and the consequent reduction of the pedestal pressure (density pump-out). Toroidally localised diagnostics with high radial resolution in combination with toroidally rotating n=2 MP-fields are used to characterise the 3D boundary displacement. The amplitude, the toroidal phase and the dependence on applied poloidal mode spectrum of the displacements are in good agreement with 3D single fluid ideal magnetohydrodynamic (MHD) code predictions (MARS-F, VMEC). So far, we have no indication that resistive MHD modes (tearing modes) induced by mode penetration from the external MPs play a role. The induced 3D MHD geometry does not only lead to significant displacements of the plasma boundary, but it also changes the local stability at the edge. We observe ideal MHD modes with ballooning structure only at certain field-lines (helical position) within the 3D geometry in the H-mode edge barrier region [2]. Infinite-n ballooning stability analysis using a 3D equilibrium from VMEC demonstrates that the local reduction of the magnetic shear causes strongest instability at exactly the same field lines. Perturbations of the local parallel current profile and the additional torsion due to the 3D geometric shape of the magnetic surface are responsible for the changes in local magnetic shear. Additionally, not only the ballooning modes, but also the dynamics of the ELM crashes are influenced by the 3D MHD geometry. [1] M. Willensdorfer et al, Nucl. Fusion 57, 116047 (2017) [2] M. Willensdorfer et al, Phys. Rev. Lett. 119, 085002 (2017)

Speaker: Dr Matthias Willensdorfer (IPP Garching)

summarySlide.pptx

713 Implementation of Synchronous Reference Frame Theory based Shunt Active Power Filter using DSP Controller.

This paper conceptualizes shunt active power filter (SAPF) using synchronous-reference- frame (SRF) theory to mitigate the harmonics present in the power system. The shunt active power filter injects a suitable compensating current at a point called point of common coupling (PCC) so that the harmonics present in the line are cancelled out and sinusoidal nature of current waveforms is restored. A three phase current controlled voltage source inverter (VSI) with DC link capacitor across it is used as an active filter. Synchronous reference frame (SRF) algorithm is developed for low voltage laboratory prototype using TMS320F28335 Digital Signal Processor (DSP). The experimental test results demonstrate that the viability of the control strategy is successful in meeting the IEEE 519-1992 recommended harmonic standard limits. Keywords— Active Power Filter, DSP controller, Synchronous Reference Frame.

Speaker: Mr Chandra Kishor Gupta (Institute For Plasma Research)

ckgupta_slides_fec2018.pdf

714 Installation and Commissioning of 80K Liquid Nitrogen Booster System

The static heat loads on the 80 K thermal shields of SST-1 will be removed using single phase liquid nitrogen cooling at 0.7 MPa. The single phase liquid nitrogen is obtained using 80 K liquid nitrogen booster system. Booster system is in form of three storey building as pump cryostat at bottom, sub-cooler vessel cryostat at middle and pressurized vessel cryostat at upper. Boosting system utilized three centrifugal cold pumps at liquid nitrogen services among them two remain in operation and one remain in cold standby mode as redundant. Pre-assembly leak tightness test at individual components level were carried out before final integrated installation of booster system. Functional validation of booster system as per defined PFD was carried out after installation at IPR site. Booster system’s different modes of operation like purge, LN2 filling, first phase cool-down, second phase cool-down, steady state and warm up were successfully tested along with their process alarms, safety interlocks and failure events. The booster system performance test was conducted using system inbuilt dummy load of 20 kW @ 80 K, which is similar to actual heat load on SST-1 thermal shields from ambient. 80 K booster system installation and commissioning detail is presented in this paper.

Speaker: Mr Rakeshkumar Patel (Institue for Plasma Research)

Rakesh_FEC2018_Summary_slide.pptx

715 Integrated simulation of runaway electrons: a backward Monte-Carlo approach for a fluid-kinetic self-consistent coupling

The dynamics of runaway electrons (RE) is a complex process and, although significant progress has been made in the understanding of individual isolated pieces of the puzzle, a predictive capability calls for an Integrated Simulation (IS) effort. In this presentation we report on recent progress on this problem. The goal is to use the BMC method [1] to couple a kinetic description of the RE population to a fluid description of the background plasma and the self-consistent evolution of the electric field. In addition, the IS includes a synchrotron emission (SE) synthetic diagnostic [2] for model validation. The main novel aspects of our contribution are the use of a probabilistic coupling based on the BMC method, the incorporation of the often-ignored configuration space dependent dynamics, and the use of a flux surface averaged transport model along with a Grad-Shafranov 2D equilibrium. At the heart of our IS effort is the recently developed Kinetic Orbit Runaway electron Code (KORC) that computes relativistic RE orbits using either full-orbit 6-D (KORC-FO) or guiding center (gyro-averaged) descriptions (KORC-GC) incorporating the full geometry of the magnetic field, the spatial dependence of the electric field, and synchrotron radiation damping. Collisions are incorporated using a Monte-Carlo method with plasma temperature, plasma density and impurities dependent collision frequencies [3,4,5]. To account for the spatio-temporal variations of plasma parameters in KORC, we developed a fluid code that solves the time-dependent flux surface averaged transport equations [6]. Disruption mitigation is simulated by introducing an impurity neutral gas pellet. The kinetic information computed with KORC is feed back to the plasma state and electric field solvers using the BMC method that computes the RE production rate. As an application of the IS framework we study RE generation during rapid plasma shutdown by impurity injection in DIII-D and ITER-like plasmas. [1] G. Zhang et al., Phys. Plasmas 24, 092511 (2017); [2] L. Carbajal et al., Plasma Phys. Control. Fusion 59, 124001 (2017); [3] L. Carbajal et al., Phys. Plasmas 24, 042512 (2017); [4] D. del-Castillo-Negrete et al., Phys. Plasmas, accepted (2018); [5] D.A. Spong, et al., Submitted to Nuclear Fusion (2018); [6] J. Lore et al., CP11.098 APS DPP Meeting (2017).

Speaker: Diego del-Castillo-Negrete (Fusion Energy Division. Oak Ridge National Laboratory)

716 Interactions of runaway electrons with Alfvén and whistler waves

Runaway electrons are of significant interest in tokamaks due to their potential for damage to plasma facing components. Runaways are of particular concern following disruptions when the plasma undergoes a thermal quench and a subsequent current quench; these lead to large loop voltages that can rapidly create runaways. Due to the risks of performing intense runaway experiments, the generation of runaways and the rate at which they can be suppressed is a crucial issue for modeling. Comparison of electric field thresholds from a range of tokamaks with theoretical predictions has shown that the observed thresholds have generally been higher than predictions [R. S. Granetz, B. Esposito, J. H. Kim, R. Koslowski, et al., Physics of Plasmas **21**, 072506 (2014)]. This discrepancy can exist for a variety of reasons, but runaway-driven instabilities and scattering from plasma waves are mechanisms not taken into account in the existing predictions. In this paper, examples of both resonant and non-resonant runaway interactions with Alfvén and whistler waves are analyzed and compared with recent DIII-D experiments [D. A. Spong, W.W. Heidbrink, C. Paz-Soldan, et al., submitted to PRL (2018)]. The analysis is based on relativistic Monte Carlo models that include runaway/partially ionized impurity collisions, synchrotron radiation, and wave mode structures. The mode structures are calculated using the TAEFL/FAR3D gyrofluid models (for Alfvén instabilities) and the AORSA all orders full-wave RF model (for whistler instabilities). In addition to an improved understanding of runaway generation, this can also lead to new methods for runaway control.

Speaker: Dr Donald Spong (Oak Ridge National Laboratory)

SummarySlideTH-P8-17.pdf

717 Ion Cyclotron Range of Frequency Power: Progress in Operation and Understanding for Experiments with Metallic Walls

Significant progress in applying ICRF power to ASDEX Upgrade (AUG) has been achieved in the last years; this progress has been associated with a similar progress in our understanding and capability to model the relevant processes. The two main challenges of the ICRF system (power coupling and impurity production) have been tackled successfully.
First, the outer mid-plane gas injection techniques that improve the coupling of the fast wave to the confined plasma by increasing the density in front of ICRF antenna have been well established experimentally and consistently modelled numerically. With midplane gas puffing, the local edge density increase in front of the antenna leads to a shift of the fast wave cut-off position closer to the antenna by 2cm. The results were confirmed with the new density measurements in front of the antenna. The ICRF coupling increases by 120 pct (25 pct for top gas puffing).
Second, with the installation of the 3-strap antennas in AUG, it was clearly demonstrated that the ICRF-specific tungsten (W) sputtering can be successfully mitigated with a proper antenna design. The reduction of the W sputtering with the 3-strap antennas has been achieved by minimising the RF currents on the antenna surfaces that are exposed to the scrape-off-layer (SOL) plasma. The strap power balance measurements confirm that the local RF currents, rectified DC currents and the W sputtering yield at the antenna side limiters experience a clear minimum close to a phasing between the central and the outer straps of 180 deg and a power balance ratio Pcen/Pout of 2. For this optimal choice, the local source of sputtered W at the limiters is reduced by a factor between 1.5 and 6, depending on the location. This is understood, modelled and confirms the hypothesis of sheath rectification as the source of the sputtered W.
Furthermore, the new 3-ion ICRF heating scenario, which can produce very energetic particles, has been successfully reproduced in AUG.
The progress in operation, as well as in understanding and modelling capability is strongly supported by improved ICRF diagnostic coverage including density measurements directly in front of the antenna by reflectometry, advanced RF coupling characterisation, measurements of antenna limiter currents, B-dot probes, Ion Cyclotron Emission (ICE) measurements as well as by the dedicated test arrangement IShTAR.

Speaker: Prof. Jean-Marie Noterdaeme (Max Planck Institute for Plasma Physics)

summary_slide_v2.pdf

summary_slide_v2.pptx

718 IST contributions to the ASDEX Upgrade edge and divertor physics using microwave reflectometry

Information of the plasma density is essential for the study and operation of magnetically confined fusion devices. Microwave reflectometry appears as an attractive diagnostics due to its high temporal and spatial resolution and its application to profile as well as fluctuation measurements. The microwave reflectometry systems developed by IST for ASDEX Upgrade consist of: (i) multi-band frequency modulated continuous wave (FMCW) O-mode reflectometer with the unique capability of providing simultaneous profile and fluctuations measurements on the high-field side (HFS) and low-field side (LFS), making it the ideal diagnostic for poloidal asymmetry studies; (ii) fast frequency hopping O-mode reflectometer used to obtain more detailed information on density fluctuations at the LFS; and (iii) A multichannel X-mode reflectometry diagnostic recently installed to measure the edge density profile in front of the ICRF antenna. This contribution presents an overview of the scientific results obtained on ASDEX Upgrade where the different reflectometry systems are used in a complementary way in order to address some of the key issues under investigation in this device. Experimental results will be presented on topics such as: (i) Influence of the high-field side density front on the midplane density profiles; (ii) Edge turbulence in different states of divertor detachment; (iii) Edge instabilities across the L-H transition and in H-mode; (iv) Understanding density profiles in front of the ICRH antenna; (v) Synthetic reflectometry diagnostic; and (vi) Real-time plasma position control. The experimental results obtained demonstrate that the IST reflectometry systems provide a valuable contribution to a better understanding of important physics issues such as pedestal instabilities, SOL turbulence, dynamics of the density profiles and connection between midplane and divertor conditions. Different upgrades are under development that will provide uniquely flexible diagnostics for combined profile and fluctuations measurements particularly relevant for edge instabilities and turbulence studies.

Speaker: Dr Carlos Silva (IST/IPFN)

Summary slide FEC 2018.pdf

719 Manufacturing Technologies for UHV Compatible 10 MW/m2 High Heat Flux Components for Application in Fusion Devices

High heat flux components form the primary interface of thermal management of injectors in the fusion devices. The requirement for such application varies from 1 to 10MW/m2. UHV compatibility is the inherent characteristics of such components also manufacturing processes involves the development of specific material, process qualification of special process like EB welding and component performance validation. One such component of active thermal management in Neutral Beam injector is Hypervapatron based Heat transfer element (H-T-E) which is designed to absorb heat flux as high as 10MW/m2. The realization route is through prototype and established on one to one model and evaluating their performance. The development route of the H-T-Es represents several important areas like 1) development of precipitation hardened CuCrZr material characterized for its fatigue life (more than 1,00,000 stress controlled cycles), mechanical properties at ambient ( UTS > 384 MPa, elongation > 13 %) and at operational temperature i.e. 350֯C ( UTS >263 MPa, Elongation > 14%), restricted chemical composition range of Cr, Zr, Cd and O2 to enhance precipitation effect and weldability of the component 2) similar ( CuCrZr to CuCrZr) and dissimilar material (CuCrZr-Ni-SS316L) joining by advanced technology like EB welding in controlled environment to enhance the localized high heat input over a large weld penetration depth with minimal distortion and thereby overcome the effect of thermal diffusion by typical copper during welding 3) validation of these weld joints w.r.t international codes/standards 4) validation of design through performance testing by simulating the operational scenario. Successful realization of this route establishes H-T-Es as main baseline components of High Heat Flux system or Neutral Beam system. Similar application areas can be identified in various fusion devices. The paper presents the implementation of this realization route of prototype Heat Transfer Elements including the details of assessment carried out w.r.t application.

Speaker: Mr Hiteshkumar Kantilal Patel (ITER India, Institute for Plasma Research)

Summary Slide_FIP_P8-20.pdf

720 Measurement and modelling of magnetic configurations to mimic overload scenarios in the W7-X stellarator

Experiments were performed in short pulse operation (OP1.2) on the Wendelstein 7-X (W7-X) stellarator using a set of five magnetic configurations that were designed to mimic the topology and resultant divertor fluxes of a high-power long-pulse scenario that is predicted to cause component overload. These experiments demonstrated the capability of edge transport simulations to accurately predict the location and relative magnitude of wetted areas on divertor and baffle components, as well as the ability to mimic the effects of otherwise inaccessible operational conditions (toroidal current, significant beta) using the magnetic coil set. The overload scenario is predicted to occur in the actively cooled divertor operational phase (OP2) of W7-X, in configurations where the toroidal current is evolution (over ~100 s) causes the edges of the primary divertor components along the pumping gap to receive a load in excess the of the 5 MW/m2 rating. The pulse length and energy input limitations of the non-actively-cooled operational phases of W7-X prohibit direct access to the overload scenario. To validate the predictions of the heat flux patterns and magnitude, and to establish baseline measurements for comparison before two scraper element components are installed, a set of five configurations were designed to mimic the effects of finite plasma beta and toroidal current on the magnetic topology and flux patterns. The mimic configurations correspond to five values of the OP2 net toroidal current as it evolves from 0 to 43 kA, including the peak overload case of 22 kA. Measurements of the divertor heat fluxes, H-alpha emission, and neutral pressure were obtained in each configuration with 2 MW of input power and hydrogen and helium as working gasses. In the steady-state and peak overload mimic configurations, density and power scans were performed. The heat flux patterns are well described by predictions from both field-line diffusion and higher fidelity EMC3-EIRENE simulations, indicating that the approach of mimicking inaccessible OP2 configurations is successful and that rapid diffusion-type calculations are valid for approximating fluxes. These results improve confidence in the predictions for advanced operation of W7-X, and more broadly, in the ability to predict the heat flux patterns in stellarator divertors.

Speaker: Dr Jeremy Lore (ORNL)

summary_slide.pdf

721 Mechanical Engineering Aspects for Overhauling of Helium Compressor and heavy duty Electrical Motors of 1.3 kW Helium Refrigerator/Liquefier system

Institute for Plasma Research has 1.3 kW helium refrigerator/liquefier (HRL) cryogenics system, which is in operational state since 2003. The cryogenic HRL plant used to cool down the magnets of Steady State Super-conducting Tokomak (SST-1). Three identical Mycom make helium screw compressors with Fimet make 315 kW Electrical Motor, Oil removal system operate to supply high-pressure helium gas to HRL cold-box and sub-systems. Heavy duty electrical motors of rated for 315 kW in an asynchronous induction drive is used to run the helium screw compressors. The compressors along with the electrical motors run on round the clock basis for a month long continuous operation. Hence, its reliability and availability is mandatory. Therefore, it is very essential to maintain and overhaul the Compressor and Motors as per their schedule of operation hours to facilitate the reliable operation of the Tokomak. In this paper, we will describes Mechanical engineering aspects of overhauling experiences of compressors and motors that include their alignment with compressor, online temperature monitoring and motor cooling arrangements and vibrations measurement of compressor, motor and skid.

Speaker: Mr Jayant Patel (Institute for Plasam Research, Bhat Indira Bridge, Gandhinagar, Gujarat, India)

Summary of Overhauling _Jayant Patel

722 Modeling runaway electrons dynamics in tokamak plasmas: progresses and challenges

The sudden termination of a plasma discharge known as a major disruption is a well-identified difficulty from the beginning of tokamak research, which remains still today particularly problematic for the design of a reliable fusion reactor. The key questions are principally related to the growth rate of relativistic electron population, closely linked to the level of the critical electrical field for an electron to run-away, and the upper energy limit that it can reach. Recently, very important achievements have been obtained in this domain. The introduction of the synchrotron radiation reaction force in kinetic calculations is shown to limit the upper energy of the runaway beam to 20-30 MeV consistent with observations [1]. Refined studies have also included the effect of bremsstrahlung radiation [2]. The calculation of the runaway avalanche growth rate has been improved by considering accurately the magnetic field inhomogeneity [3] and the screening effect of partially ionized impurities [4]. With the development of a synthetic diagnostic for the synchrotron radiation [5], numerical tools have reached the required level to perform realistic kinetic simulations of the runaway electron population for assessing effective control capabilities of existing techniques for ITER. A review of the progresses and challenges is performed. 1. J. Decker, et al., Plasma Phys. Control. Fusion 58 (2016) 025016 2. O. Embreus, et al., New J. Phys. 18 (2016) 093023 3. E. Nilsson, et al., Plasma Phys. Control. Fusion 57 (2015) 095006 4. L. Hesslow, et al., Phys. Rev. Letter 118 (2017) 255001 5. M. Hoppe, et al., Nucl. Fusion 58 (2018) 026032

Speaker: Dr Yves Peysson (CEA)

723 Multi-Scale Interaction between Ballooning Mode and Electron-Scale Turbulence and the Mesoscale Structure Formation in the Edge Pedestal

Raghvendra Singh1, Hogun Jhang1 and Maolin Mou2, 3 1National Fusion Research Institute, Daejeon 305-333, Republic of Korea 2College of physical Science and Technology, Sichuan University, 610065 Chengdu, China 3Key Laboratory of High Density Physics and Technology of Ministry of Education, Sichuan University, Chengdu, 610064, China Email address: rsingh129@nfri.re.kr; rsingh129@gmail.com Recent MHD simulations [1-2] have demonstrated that one of the important ingredients giving rise to the ELM [3] crash is the hyper-resistivity in the Ohms law. In this paper, we address three key issues: i) the source for the hyper dissipations (e.g. hyper resistivity and hyper viscosity); ii) high-k ballooning mode (BM) driven by hyper-dissipation near marginally stable BM boundary; iii) the possible nonlinear saturation mechanism of the high- BM. We present a simple self-consistent theoretical model for hyper-resistivity ballooning modes (HRBM) accounting for the multi-scale interaction between the long scale BM and the short scale ETG mode above a BM threshold. Here, the coupling between the BM and the ETG turbulence has been identified as a primary mechanism for the generation of the long scale hyper-resistivity ( ) [4] and hyper-viscosity ( ) in BM dynamics. Based on the linear theory, the physics of HRBM mode has been elucidated, as well as the parameter space where it is important. It is shown that the growth rate of HRBM increases with the increasing poloidal wave vector ( ) whereas standard BM growth decreases with . Another long standing problem is how KBM (here particularly HRBM) saturation occurs so rapidly. The possibility of long scale zonal fields [e.g. mesoscale poloidal magnetic fields (zonal current) and radial magnetic fields (streamers)] are examined in this study. Further their potential impact on thermal transport and an ELM crash are also considered. [1] X.Q. Xu, et.al, PRL 105, 175005 (2010) [2] T. Rhee, et.al, Nuclear Fusion 55, 032004 (2015) [3] P. B. Snyder, et.al, Phys. Plasmas 9, 2037 (2002) [4] R. Singh, et al, 25th IAEA Fusion Energy Conference, Saint Petersburg, Russia, 2014 (International Atomic Energy Agency, Vienna), IAEA-TH/P1-15

Speaker: Dr Raghvendra Singh (National Fusion Research Institute)

724 Non-linear interaction of runaway electrons with resistive MHD modes in an ITER VDE

Uncontrolled termination of post-disruption runaway electron (RE) current can cause deep localized melting of the first wall and this poses a serious challenge to the successful operation of fusion grade tokamaks, including ITER. Since the deconfinement of REs depends on the timescale of flux surface reformation and the plasma stability itself is affected by the runaway current, the interaction between REs and MHD is highly non-linear and has important consequences. This is the motivation of the present work, that complements the tracer particle approach for REs. The final goal is the self-consistent modeling of REs in a disrupted plasma through non-linear MHD simulations of disruption.

In this contribution, we present results that focus on the interaction of resistive MHD modes with runaway electron growth. This is modeled by extending the non-linear MHD code JOREK by including a fluid model for the evolution of runaway electron density. Runaway generation due to Dreicer as well as the avalanche sources are included (with an option for initializing an arbitrary RE seed profile), with advection contributions from parallel runaway velocity and an ${E}\times{B}$ drift. The first studies shown here are based on pseudo thermal quenches that are obtained by artifically increasing the perpendicular thermal conductivity ${k}_{\perp}$ of the plasma in equilibrium, which in turn triggers the generation of REs.

The JOREK model with REs is applied to analyse the interaction of the $\left(1,1\right)$ resistive internal kink with runaway electrons, given that the resistive kink is naturally destabilized due to the peakedness of the RE current profile that can lead to the central safety factor $q_0$ dropping below unity. A numerical study of this problem was carried out recently using the spectral MHD code EXTREM , where several simplifying assumptions were made, such as an independent thermal decay, decoupling RE current from perpendicular ${E}\times{B}$ dynamics and the neglect of parallel fluid velocity $V_{||}$. In our study, an attempt is made towards a more comprehensive treatment of the problem. The effect of the mode growth on the RE seed redistribution and the final RE profiles will be discussed in addition to the influence of REs on the mode excitation and dynamics.The effects of pre-disruption $q_0$ and the thermal quench rates will be studied.

Speaker: Dr Vinodh Kumar Bandaru (Max-Planck-Institute for Plasma Physics, Garching)

Bandaru_summary_slide_IAEA.pdf

Bandaru_summary_slide_IAEA.pptx

725 Non-linear interplay between edge localized infernal mode and plasma flow

Quiescent H-mode (QH-mode) was first discovered in DIII-D as an ELM-free H-mode regime, which is usually accompanied by the presence of edge harmonic oscillations (EHOs). EHOs are believed to provide necessary transport to eliminate ELMs by dynamics of the plasma itself. The saturated kink-peeling mode has been suggested as a possible candidate for EHO. In this work, we consider another instability – the edge localized infernal mode (ELIM) – as a possible candidate, for plasmas where the large edge bootstrap current causes local flattening of the plasma edge safety factor, or even the magnetic shear reversal in the pedestal region. An ELIM is a low-n (n is the toroidal mode number) instability similar to the conventional infernal mode, but being localized at the plasma edge where safety factor is locally flattened. Finite plasma pressure in the pedestal region drives this mode. A saturated ELIM, due to non-linear interaction with toroidal plasma edge flow, can be responsible for EHO. Our investigation is divided into three stages: (i) linear stability, or the ELIM onset condition, at a given plasma flow; (ii) comparison of various toroidal torques, generated by a linear mode instability; (iii) non-linear interplay between an ELIM and the toroidal plasma flow.

Speaker: Dr Guanqi Dong (SWIP)

726 Nonlinear 3D simulations of Vertical Displacement Events in tokamaks

Vertical displacement events (VDEs) where the plasma moves rapidly towards the wall can cause large electromagnetic forces on the vessel structures with possible damaging effects for large tokamaks. Non-axisymmetric modes developing during the VDE can lead to asymmetric, sometimes rotating forces on the vessel which can be even more severe. Large-scale 3D simulations play a crucial role on the path towards assessing and preventing the damaging effects of VDEs on vessel components in future large tokamaks like ITER.

We use the high-order finite element code M3D-C^1 [1] to perform 2D and 3D nonlinear MHD simulations of VDEs in tokamaks including a resistive wall model [2]. In order to develop predictive capabilities, the simulation results are benchmarked with other codes as well as validated against existing experimental measurements.

2D and 3D nonlinear MHD simulations of VDEs are based on and validated against discharges in NSTX [3] as well as DIII-D. The results of a set of axisymmetric VDE calculations based on NSTX discharge #132859 show the sensitivities of the early VDE evolution to different parameters, in particular the halo resistivity. 3D simulations show how non-axisymmetric modes arise in the late VDE phase and lead to a stochastization of the magnetic field lines which allows for an efficient release of thermal energy into the wall. The thermal quench is followed by a fast decay of the plasma current and rise of the wall current.

A detailed benchmarking activity between the M3D-C^1 code and the 3D nonlinear MHD code NIMROD [4] based on an NSTX discharge is being performed. The comparison of axisymmetric VDE calculations is focused on the early VDE growth and the wall forces. We plan to extent this benchmark to 3D simulations with a 2D wall. In addition, an axisymmetric benchmark between the M3D-C^1 code and the CarMaONL code [5] based on a standard ITER scenario using a simplified 2D model of the ITER first wall is in progress.

[1] S. C. Jardin, et al., Comput. Sci. Discov. 5, 014002 (2012).

[2] N. M. Ferraro, et al., Phys. Plasmas 23, 056114 (2016).

[3] D. Pfefferle, et al., Phys. Plasmas (2018). Submittted.

[4] C. R. Sovinec, et al., J. Comput. Phys. 195, 355 (2004).

[5] F. Villone, et al, Plasma Phys. Controlled Fusion 55, 095008 (2013).

Speaker: Dr Nathaniel M. Ferraro (UsPPPL)

Summary_Slide_Krebs.pdf

727 Nonlinear turbulent parallel momentum transport due to blobs

Meso-scale size structures including the blobs in the edge plasma can not only transport particle and heat out, but may also contribute to the plasma poloidal/toroidal rotation, namely, the momentum transport.[1] Turbulent parallel momentum stress can be divided into three components, which are diffusive, covective and residual parts. In the presented work, the triplet nonlinear term is derived by using EDQNM method in 3D Hasegawa-Wakatani system. It is shown that the triplet nonlinear term is comparable to the quasilinear terms, i.e. the first two terms of quasilinear stress, in strong turbulence regime such as blobs. If the radial scale length of large edge coherent structure is bigger than its poloidal scale length, nonlinear residual stress can provide opposite torque with respect to the quasilinear ones and negative nonlinear diffusivity. These effects introduce inward momentum flux so that the rotation in edge region is possibly reversed and momentum is convected into core region. Moreover, it is found that nonlinear coupling for vorticity is the dominating mechanism in parallel momentum transport.

Speaker: Dr Yang Li (Department of Engineering Physics, Tsinghua University, Beijing 100084, China)

728 Nuclear design issues of a stellarator fusion power plant with breeder blanket in comparison to tokamaks

The European Roadmap to the realisation of fusion energy considers the stellarator concept as a possible long-term alternative to a tokamak fusion power plant (FPP). A corresponding R&D programme is conducted by the EUROfusion consortium to advance the stellarator concept with the scientific exploitation of the W7-X experiment. The aim is to optimise the stellarator performance, prove the feasibility for steady-state operation, and, on such a basis, study the prospects of a power producing plant based on the helical-axis advanced stellarator (HELIAS) configuration. An important issue towards this goal is the analysis of specific nuclear issues of a HELIAS type FPP equipped with a tritium breeding blanket. This work addresses these issues based on the achievements of the blanket development work conducted within EUROfusion’s Power Plant Physics and Technology (PPPT) programme on a tokamak fusion power demonstration plant (DEMO) and recent results obtained for HELIAS in the neutronics area.

Speaker: Dr Ulrich Fischer (Karlsruhe Institute of Technology)

729 Numerical investigations towards manufacturing of high current carrying superconducting CICC

Fusion relevant high field superconducting magnets require large current carrying conductor of the order of tens of kilo-Amperes. High current carrying the cable in conduit conductor (CICC) are based on low-temperature NbTi and Nb3Sn superconductors. The manufacturing of superconducting cable is carried out by twisting required strands into the desired configuration by application of tensile and compressive forces using cabling machine. The selection of tensile and compressive forces is critical as it can lead to deformation of superconducting strands which may lead to degradation of its performance. The long length CICC is manufactured by adopting pulled through technique where the superconducting cable is inserted inside stainless steel jacket tube which further shaped to require size using rotary swaging. The cold working during this process results in the generation of stresses in jacket material as well as in superconducting cable. The effect of critical factors on the distribution of stresses during cabling (such as twist pitch, contact angles, and compression forces) and jacketing (such as the percentage of cold work and feed velocity) of CICC have been simulated using FEA. The contact stress and deformation between two strands of cable and distribution of radial stresses along with a change in thickness for jacket tube have been estimated during this numerical investigation. These kinds of studies are essential to generate and optimize the manufacturing parameters for cabling and jacketing of CICC.

Speaker: Mr Mahesh Ghate (Institute For Plasma Research)

Summary Slide_IAEA-FIP_P8-15.pdf

730 Operation and Control of 42 GHz Gyrotron system in ECRH

Electron Cyclotron Resonance Heating (ECRH) is one of the essential RF heating system used for pre-ionization and heating experiments in Aditya and SST1 tokamak. The 42 GHz gyrotron system capable of delivering 500kW RF power for 500ms has been installed for operation with Aditya and SST1 tokamak. Gyrotron operation requires a systematic and sequential controlled operation of different power supplies. High voltage power supplies connected with collector and anode needs more attention for pulsing the gyrotron tube for conditioning as well as for microwave output. As Gyrotron tube is an expensive microwave device, fast interlock circuits are implemented for its protection during any abnormal event. Data Acquisition and Control systems (DAC) are designed and developed for gyrotron operation considering all safety measures and protection. Gyrotron system can be operated standalone as well as remotely through programmed time base trigger command from Central control system. VME based DAC and the other PXIe based DAC have been installed with the gyrotron system and are under operation with SST-1 and Aditya. Recently VME based DAC has been upgraded with NI Labview based GUI and control interface with new advance features. Also control application software on target VME hardware has also been upgraded for two pulse operation. PXIe based DAC has been designed to operate both 42 GHz and 82.6 Ghz gyrotron with a single console application. The essential part of Gyrotron operation is pulsing the anode and cathode high voltages simultaneously with pre programmed delay and rise time with fast active interlocks. Gyrotron operation covers the start up sequence of power supplies, its pre-inspection and checking of different interlocks, HV pulse interface test, conditioning of gyrotron tube. This paper explains the sequence of steps necessary for gyrotron operation and control. It also showcases the features of DAC systems for gyrotron operation, its software design, adopted methodology and the problems faced during operation and control of gyrotron.

Speaker: Mr JATINKUMAR PATEL (INSTITUTE FOR PLASMA RESEARCH)

Summery Slide Jatinkumar Patel FEC 2018.pptx

731 Plasma dynamics and transport studies in Wendelstein 7-X

A primary goal of Wendelstein 7-X (W7-X) operation is to demonstrate stationary, long pulse discharges at fusion-relevant plasma densities and temperatures. Studies on the behavior and the control of impurity ions originating from plasma-wall-interaction with the divertor and other plasma facing components is a crucial issue potentially leading to a thermal collapse and dilution of the fuel. W7-X had been equipped with a bolometer diagnostic, the VUV/EUV survey spectrometer system HEXOS, a soft X-ray camera array and a pulse height analysis system as well as two imaging Johann X-ray spectrometers. To distinguish between diffusive and convective impurity transport, a laser blow-off system as transient impurity source was installed at W7-X. In order to characterize the transport properties, the experimental results are compared to the transport code STRAHL. Since W7-X is optimized with respect to neoclassical transport, it is expected that turbulence transport plays a significant role in the regulation of radial particle and heat transport in the core and edge plasma. Fully-nonlinear gyrokinetic simulations in the three-dimensional W7-X magnetic field geometry indicate that turbulence is dominated by ion temperature gradient driven modes with an amplitude pattern which forms relatively narrow poloidal stripes on the W7-X flux surface. Key diagnostics are a phase-contrast imaging diagnostic (PCI) measuring core plasma density fluctuations, radial and poloidal correlation ECE systems for the diagnostics of electron temperature fluctuations, and a set of correlation and Doppler reflectometry systems, which provide edge poloidal flows and density fluctuations. The experimental program has focused on the comparison to gyrokinetic GENE simulations. Closely related to the plasma profiles is the question of the stability of the plasma state. In magnetic configurations with co-ECCD (i.e., the bootstrap current and the driven current are co-aligned), sudden drops in core temperature (measured by the ECE diagnostic), diamagnetic energy, Mirnov diagnostic and X-ray cameras have been observed. The ECCD-induced crashes repeat on a time scale of several ms to seconds, depending on the amplitude of the driven current. Combined data analysis supported by modeling activity has been started to improve the understanding of the mechanism(s) behind these events.

Speaker: Dr Olaf Grulke (MPI for Plasma Physics)

Grulke_summary_slide.pdf

732 Plasma termination by excess fuel and impurities in TJ-II, LHD and W7-X

Plasma termination by excess fuelling or impurity interaction is a safety relevant event in potential fusion reactors. Sudden termination of plasma operation is an aspect that enters material requirements in terms of released energies, localization and respective time-scales of the plasma terminating event. In tokamaks, such events may lead to disruptions or thermal quenches. While disruptions are not expected in (currentless) stellarator/heliotron operation, thermal quenches are certainly to be illuminated for reactor scale stellarators and heliotrons as well. This report is a study on plasma termination in TJ-II, W7-X and LHD. The confinement in W7-X and LHD allows one to study long-mean-free-path collisionality conditions in the plasma core.

Evidence for stellarator/heliotron specific behavior is given by the spatio-temporal evolution of the electron temperature. After the injection of two fuelling pellets into an LHD discharge, the second pellet induces a cooling of the plasma center leading to a temperature hole after about 100ms (tau_E). It is concluded that the stationary confining field has a beneficial impact. In TJ-II, the peaking of TESPEL particle deposition closer to the centre facilitates plasma recovery. For W7-X, plasma termination due to massive LBO tungsten injection shows energy decay by cooling of the plasma. The electron temperature decays on the time scale of energy confinement (~100ms), while the plasma density remains almost constant (even slightly increasing). The plasma is finally terminated along with a strong increase of radiation representatively shown here as increase of impurity lines due to wall material (iron). Similar evolution of temperature and density is observed after iron impurities terminating ICRH long pulse experiments on LHD.

The systematic comparison of plasma terminating events by cryogenic pellets, induced impurity injection or changes of the heating gives evidence that the observed termination takes place on a time scale corresponding to the energy confinement time. Close to marginal termination, the beneficial effect of stellarator confinement of the vacuum field leads to transient plasmas that are cold in the center but may recover after typically 1s. The findings indicate the benign impact on transient loads in case of plasma termination in stellarators and heliotrons.

Speaker: Dr Andreas Dinklage (Max-Planck-Institut für Plasmaphysik)

preprint_08.docx

preprint_08.pdf

summarySlide.pptx

template.pdf

733 Predictive Simulations of Core-Edge Plasma for Tokamak Plasma using BALDUR Code

Core-Edge simulations of the low confinement mode (L-mode) plasma are carried out using 1.5D BALDUR integrated predictive modeling code in. In each simulation, the plasma current, temperatures, and density profiles for both core and SOL regions are self-consistently evolved. The plasma profiles in the SOL region are simulated by integrating the fluid equations, including sources, along and perpendicular to the field lines. The transport coefficients in the SOL region are determined by either one of three transport models: (A) the neoclassical transport, (B) constant transport coefficients, and (C) the anomalous transport. The solutions in the SOL subsequently provide as the boundary conditions of the core plasma region. The core plasma transport model is described using a combination of anomalous transport by Multi-Mode-Model version 1995 (MMM95) and neoclassical transport provided by NCLASS module. By comparing with 38 L-mode discharges from TFTR, DIII-D, and JET, it is found that the mean standard deviations of the plasma profiles with SOL transport modeled by the anomalous transport are 19% for the electron density, 21% for the electron temperature, and 26% for the ion temperature, while the simulation results using the SOL transport modeled with a fixed constant or the neoclassical transport show higher deviation. Furthermore, the BADLUR code is used to predict the plasma profiles near the edge of the HT-6M tokamak based on the previous developed model. When the plasma current is kept constant and the average density is varied between $1\times 10^{19} - 9\times 10^{19}$ m$-3$, the simulations show that power loaded to the limiter is about 30 - 550 kW and the total ion flux to the SOL region is about $2\times 10^{19} -2 \times 10^{20}$ s$^{-1}$. Note that no auxiliary heating is provided. The temperature at the separatrix is found to be about 5 - 7 eV.

Speaker: Dr Apiwat Wisitsorasak (King Mongkut's University of Technology Thonburi)

734 Preparing the ICRH system for the Wendelstein 7-X stellarator

An important aim of W7-X is to demonstrate fast ion confinement at volume averaged beta values up to 5% for which W7-X was optimised [1]. These high beta values correspond to plasma densities above 10^{20}m^{-3}. Mimicking the behaviour of alpha particles in a future stellarator requires the presence of energetic ions with energies in the range ~100 keV in the core of W7-X high density plasmas [2]. This is a challenging task, but such a population can be created using Ion Cyclotron Resonance Heating (ICRH) using various heating schemes, including the newly demonstrated 3-ion heating scenario [3,4]. The ICRH system under construction for W7-X aims in its final configuration at delivering RF power levels up to ~1.5MW in the frequency range 25-38MHz with pulse lengths up to 10s [5]. The antenna consists of two straps and is foreseen with a pre-matching system to limit voltages in the feeding transmission lines and matching system. The shape of the antenna is carefully matched to the 3D shape of the Last Closed Magnetic Surface (LCMS) of the standard magnetic field configuration on W7-X [6]. At the standard magnetic field of 2.5T, fast (~ 100-200 keV) H, D, 3He and 4He particles can be generated in high density (n_{e} > 10^{20}m^{-3}) W7-X plasmas for studies of fast ion confinement in the optimized stellarator magnetic topology of W7-X using various heating scenarios: minority heating of H, 2nd harmonic heating of D or ^{4}He, and using the 3 ion scenario to generate fast ^{3}He in H-D or H-^{4}He mixture plasmas. A purposely-built test stand in the Institute for Energy and Climate Research/ Plasma Physics (IEK-4, Forschungszentrum Jülich, Germany) is being assembled to check the main properties of the ICRH antenna before installation in W7-X. Checks of the vacuum compatibility, voltage standoff and functionality of the radial positioning system are underway. We will provide a detailed description of the test stand, obtained results and conclusions for the use of the ICRH system at W7-X, and in as far as possible also first results obtained on W7-X.

Speaker: Dr Jozef ONGENA (Plasma Physics Lab, ERM-KMS, Brussels)

Summary slide.pdf

735 Quantification of Neutral Beam Driven Current and the effect of radial fast ion transport in ASDEX Upgrade

The neutral beam (NB) driven current, like the other intrinsic and driven current contributions to the total plasma current, is not directly measurable. Therefore, two strategies are used to investigate neutral beam current drive (NBCD). First, for quantitative investigations of the total NB driven current the measured total plasma current is compared with the sum of the calculated contributions. Second, changes in the measured plasma current profile due to changes in the neutral beam injection are examined. An issue for the quantitative approach is the large uncertainty in the reconstruction of the inductive current. This hampers quantitative conclusions on the current composition. Therefore, quantitative investigations of the non-inductive contributions were done in discharges with maximized neutral beam driven and bootstrap current fraction, leading to an almost vanishing inductive current. A pressure-measurement based correction of the fast ion content, confirmed independently by fast-ion Dα measurements, together with the improved bootstrap current formula of Hager et al. [1] leads to a quantitative decomposition of the plasma current that is consistent with the estimates of the small inductive contribution. The investigation of the reaction of the total plasma current profile to switching between on- and off-axis neutral beams aimed at revisiting a contradiction that had been found earlier: while the radial profiles of the fast NB ions seemed to behave neoclassically, the current profile appeared to deviate from the neoclassical expectations. In the new discharges the radial fast ion distribution and the radial current profile were measured simultaneously. After improvements to the diagnostics and TRANSP modeling, both diagnostics are now in agreement with each other and the small deviations from the neoclassical theory are of the order of radial transport expected due to microturbulence. Furthermore, reexamination of the old experiments yields results consistent with the new experiments. [1] R. Hager et al., Physics of Plasmas 23,4, (2016)

Speaker: Mr David Rittich (Max-Planck-Institut für Plasmaphysik)

Summary Slide

736 Recent Progress of ITER Magnet Supports Package in SWIP

see attachment

Speaker: Dr pengyuan li (southwestern institute of physics)

737 Role of the pressure position on the pedestal stability in AUG, JET-ILW and TCV in deuterium and hydrogen plasmas and implications for ITER

The role of the pedestal pressure position ($p_e^{pos}$) in the pedestal stability has been recently highlighted in deuterium (D) plasmas in AUG [1], where it was shown that an outward shift of the pressure can lead to a reduction in pedestal pressure height ($p^{ped}$). The work emphasized the role of scrape-off layer conditions and possibly separatrix density ($n_e^{sep}$) in the global confinement. Instead, the role of $p_e^{pos}$ in JET-ILW has been, so far, elusive [2]. To achieve reliable pedestal predictions for ITER it is necessary to clarify several points: - Do AUG and JET behave in a similar way in terms of the pressure position? - Does the pressure position play a role in the pedestal stability in JET? - Is the variation of $p_e^{pos}$ a general behaviour or is unique to metal wall machines? - What is the role of $n_e^{sep}$? - Does the isotope species influence these mechanisms? These questions are addressed in five steps, by (i) investigating the behavior of the pedestal structure in gas and power scans of unseeded plasmas in AUG, JET-ILW and TCV, (ii) by studying the corresponding physics mechanisms using the P-B model, (iii) by comparing the results with the self-consistent EUROPED code [3]. Further insight into the physics mechanisms are obtained by (iv) non-linear resistive MHD simulations with JOREK and (v) micro-instability analysis with GS2. When the pedestal is P-B limited, similar behaviors are observed in all three devices. The increasing fueling leads to the pedestal degradation. This is explained by the outward shift of the pedestal postion, as verified with EUROPED. A preliminary modelling suggests that the ITER pedestal can be affected by 7-8%. However, this might be an underestimation, as also $n_e^{sep}$ plays an important [1]. EPED overestimates by 25% the experimental $p^{ped}$ in the high $n_e^{sep}$ case. The reason for the discrepancy is investigated with JOREK, to assess the role of resistivity, non-linear MHD and diamagnetic effects and with GS2, to assess the role of micro-instabilities. [1] Dunne M., PPCF 59, 014017 (2017) [2] Stefanikova E., accepted in Nucl. Fusion. [3] Saarelma S., PPCF 60, 014042 (2018)

Speaker: Lorenzo Frassinetti (KTH, Royal Institute of Technology)

summary_slide.pdf

738 RT Amplitude Control loop: Testing of R&D ICRF source at High Power

Ion Cyclotron Heating and Current Drive (ICH&CD) system is one of the important auxiliary heating and current drive systems for ITER experiment [1]. Total 20 MW of IC power is required to couple with ITER plasmas using 8 independent RF sources (35-65MHz) having power handling capability of 2.5 MW at VSWR of 2:1 with other stringent specifications. To finalise the source configuration, an R&D activity has been started and diacrode based amplifier is tested successfully at 1.5 MW @ 3600 sec, VSWR 2:1 on ITER-India test facility[2]. One of the critical requirements of IC-RF source is to operate the amplifier at constant power for dynamic load condition of VSWR 2:1 and able to match the requested power within 10ms time scale. To realize this, amplitude control loop is developed using NI make PXI-7841R & LabVIEW-FPGA module [3]. The output power is controlled by changing the drive reference of Solid State Power Amplifier having in-built amplitude control loop. Further to manage the dynamic load condition, online variation of anode biasing is incorporated in this amplitude control loop. In this control loop, other parameters like screen grid current, Anode current and Anode dissipation are critically monitored and ensure constant output power by adjusting different biasing voltage in real time. Putting the reliable and safe operation at highest priority, if any of the operating parameter is changing in uncontrolled manner, source will be forced to operate in power down mode forcing internal reference generated by this amplitude control loop itself. Even if the power down mode is also not able to make operating parameter stable, local protection function initiate RF off sequence [4, 5] for reliable and safe operation of RF source. In this paper, characteristics & experimental result of amplitude control loop at high power operation (~1MW) on ITER-India test bench will be discussed.

Speaker: Mr RAJNISH KUMAR (Scientific Officer-F)

Summary slide Summary Slide.pdf

739 Runaway electron modelling in the ETS self-consistent core transport simulator

Relativistic runaway electrons are of major concern in tokamaks. Some nice tools have been developed in the recent decades, but we still miss a self-consistent simulation tool that could simultaneously capture all aspects of this phenomenon. The EUROfusion Code Development for integrated modelling project (WPCD) facilitates integration of different plasma simulation tools this by providing an Integrated Modelling framework (EU-IM) [1], and a standard data structure for communication that enables relatively easy integration of different physics codes. A three-level modelling approach was adopted to runaway electron simulation within the EU-IM [2]. Recently, a number of runaway electron modelling actors have been integrated into this framework. The first level of modelling (Runaway Indicator) is limited to the indication if runaway electron generation is possible or likely. The second level (Runaway Fluid) adopts a similar approach to the GO code [3], using analytical formulas to estimate changes in the runaway electron current density. The third level is based on the solution of the electron kinetics. One such code is LUKE [4] that can handle the toroidicity-induced effects by solving the bounce-averaged Fokker-Planck equation. Another approach is used in NORSE [5], which features full nonlinear collision operator that makes it capable of simulating major changes in the electron distribution, like slide-away. These runaway-electron modelling codes have been integrated into the EU-IM infrastructure, and into the European Transport Simulator (ETS) [6], which is a fully capable 1.5D core transport simulator. ETS with Runaway Fluid could be benchmarked to the GO code implementing similar physics [2]. Coherent integration of kinetic solvers requires more effort on the coupling, especially regarding the definition of the boundary between runaway and thermal populations, and on consistent calculation of resistivity. Some of these issues are discussed in detail providing some proposed solutions. References [1] G.L. Falchetto, et al., Nucl. Fusion, 54, 043018 (2014) [2] G.I. Pokol, et al., ECA, 41F, P2.178 (2017) [3] G. Papp, et al., Nucl. Fusion, 53, 123017 (2013) [4] Y. Peysson and J. Decker, Fus. Sci. & Tech., 65, 22 (2014) [5] A. Stahl, et al., Comput. Phys. Comm., 212, 269 (2017) [6] D. Kalupin, et al., Nucl. Fusion, 53, 123007 (2013)

Speaker: Dr Gergo Pokol (NTI, Budapest University of Technology and Economics, Hungary)

Pokol_IAEA-FEC_2018_poster.pdf

Pokol_IAEA-FEC_2018_summary_slide.pdf

740 Seeding of tearing modes by internal crash events in ASDEX Upgrade and DIII-D tokamaks

Tearing mode formation after internal crash events like sawteeth or fishbones is one of the most important MHD processes that result in a big island structure and associated confinement degradation in tokamaks. This type of tearing mode formation is considered to be the most important for future fusion reactors like ITER, because large internal events provide strong magnetic perturbations and are thus able to trigger the mode already at very small normalized pressure values. The process implies magnetic reconnection at the rational surface, which has been investigated in great detail in the ASDEX Upgrade and DIII-D tokamaks. In this paper we show that such an internal crash event leads to an ideal kink mode which transforms into a tearing mode on a much longer timescale than the crash itself. Thus, the common belief of fast formation of a big island during the crash has to be revised.

Speaker: Dr Valentin Igochine (Max-Planck-Institut für Plasmaphysik)

IAEA_2018_poster_hoch_Igochine_v2.pdf

Summary_Slide_Igochine.pptx

741 Simulation studies for Optimization of 60 MHz Rod Type Radio Frequency Quadrupole Accelerator Design at IPR

A 60 MHz Rod type Radio Frequency Quadrupole Accelerator has been designed for material studies through Ion Irradiation at Institute For Plasma Research, Gandhinagar. Ion Irradiation has been preferred for characterization of fusion research material properties due to its inherited advantages of 1) absence of high residual radioactivity 2) well defined energy, dose rate and temperature values 3) its potential for well controlled experiments along with the fact that it rarely requires more than several tens of hours to reach damage levels of 1-100 dpa range. RFQ is chosen as front end accelerator in almost all accelerators these days as it can accelerate, bunch and focus the beam simultaneously. The accelerated ion beam produced by RFQ and the subsequent reaction of the beam with different targets is used to study (a) Radiation enhanced segregation (b) Irradiated micro-structure (c) Radiation hardening (d) Irradiation assisted stress corrosion cracking in materials. For Ion-Irradiation, ion beam generated by an Electron Cyclotron Resonance (ECR) ion (H+) source coupled to (copper) Rod type Radio Frequency Quadrupole (RFQ) Accelerator through a LEBT will be accelearted to 1 MeV at 60 MHz. Usually, high current RFQ are vane type RFQ’s that are designed at higher frequencies of few hundred of MHz due to their advantage of reduced RFQ length for particular energy gain and higher shunt impedance and quality factor. But their machining is very difficult as well as they have disadvantage of presence of detrimental dipole modes. At IPR, it has been decided to use the indigenously developed RF source (35-65 MHz frequency @ 1 MW power) and design a Rod Type RFQ @ 60 MHz RF frequency to obtain the required energy gain. Design considerations involve special emphasis on reduction of beam instabilities by keeping zero-current phase advance <90 degree in longitudinal as well as transverse direction, reduction of space charge effects by avoiding resonance condition along with other considerations. Detailed beam dynamic design of 60 MHz Rod Type RFQ for hydrogen beam is carried out and a 4.2 m long RFQ comprising of 97 cells is designed after optimizing various parameters. A resonating frequency of 59.6 MHz has been achieved with 12 posts.

Speaker: Ms Renu Bahl (Institute For Plasma Research,)

Summary_FIP_P8-19_RENUBAHL.pdf

742 Simulations of Plasma Disruptions in ITER due to Material Ingress

Plasma Major Disruptions (MDs), Vertical Displacement Events (VDEs) and associated runaway electron currents in ITER are a major cause of concern in ITER operations. Major R&Ds, both experimental and well as through theory and modeling is underway across the fusion community to understand these events and find suitable amelioration techniques. In the past we have presented detailed predictive simulations of MDs and VDEs in ITER using TSC and benchmarked the results with DINA simulations . Also detailed benchmarking TSC modeling with multi-machine experimental disruptive and VDE shots were carried out to understand and improve the halo current model used in the code to have better match with experiments, which were reported earlier. However, in the earlier predictive simulations of MDs and VDEs for ITER that were carried out using TSC and DINA [3], the detailed particle and heat transport were neglected and the thermal crash was modelled by artificially specifying the plasma pressure drop in a given time scale (typically 1msec), specifying the pre-crash and post-crash final electron temperature by hand to suit a given plasma current quench time. Thus in the fast current quench cases, post thermal quench Te=6.5eV and in slow current quench cases Te=50eV were specified a priori. Also in these simulations, the generation of the runaway electrons and their effect on the disruption evolution and especially halo currents were generally ignored. In this paper, we present TSC simulations of plasma disruptions initiated by material ingress, mainly in the form of pieces of Beryllium chunk falling into the plasma from the top dome. A spherical piece of Be of radius 1cm is dropped from the top mocking that of a knocked of piece of the Be blanket top dome. The detailed impurity and thermal transport is calculated self consistently along with the evolution of thermal plasma current, halo current and runaway electron current. The impurity transport of the Be ingress and its ablation in the plasma is treated with the pellet injection model in TSC. As expected the piece of Be acts like a very slow pellet and ablates in the outer periphery of the plasma leading to edge cooling and gradual shrinking of the plasma current, finally leading to disruption. Details of this simulation with interplay between plasma current runaway and halo currents will be presented in this paper.

Speaker: Dr Indranil Bandyopadhyay (ITER-India, Institute for Plasma Research)

OnePageSummary.pdf

743 SOL transport and filamentary dynamics in high density tokamak regimes

Addressing the role of Scrape Off Layer filamentary transport is a subject of intense studies in fusion science. Intermittent structures dominate transport in L-Mode and strongly contribute to particle and energy losses in H-mode. The role of convective radial losses has become even more important due to its contribution to the shoulder formation in L-Mode, describing the progressive flattening of the density scrape off layer profile at high density [1–3]. Investigation of this process revealed the strong relationship between divertor conditions and the upstream profiles, mediated by filaments dynamics which varies according to the downstream conditions. Preliminary investigations suggested that similar mechanisms occur in H-Mode [1] and that filaments contribute the SOL transport in H-mode density limit (HDL) as well [4]. The present contribution will report on results obtained on ASDEX-Upgrade and TCV tokamaks, to address the role of filamentary transport in high density regimes both in L- and H-Mode. The combined results enlarge the operational space, from a device with a closed divertor, metallic first wall and cryogenic pumping system to a carbon machine with a completely open divertor. The mechanism of shoulder formation and the role of filaments have been tested against variation of plasma current, magnetic configuration (single and double null plasmas), and divertor neutral densities, through modification of cryopump efficiency. At constant magnetic field the density decay length increases with filament-size independently of the plasma current for both machines in L-mode, consistently with the fact that upstream profiles and divertor neutral pressure exhibit the same trend with normalized greenwald fraction. In H-Mode fueling is insufficient to cause flattening of SOL profiles in the inter-ELM phases since large neutral pressure is needed. Consistently inter-ELM blob size in AUG are found larger whenever the cryopumps is switched off. The resulting picture suggests a complex relationship between divertor and upstream profiles, where filaments are modified by divertor conditions as well as by neutral particles interaction. [1] Carralero, D et al. Nucl. Fus. 57, 056044 (2017) [2] Militello, F et al. Nucl. Fus. 56, 016006 (2016). [3] Vianello, N. et al. Nucl. Fus. 57, 116014 (2017) [4] Bernert, M et al. Plasma Phys. Control. Fus. 57, 014038 (2014).

Speaker: Dr Nicola Vianello (Consorzio RFX, Padova, Italy)

single_slide.pdf

744 Strategy and optimisation of wall conditioning at the Wendelstein 7-X stellarator

Wall conditioning in fusion devices is prerequisite to provide controlled boundary conditions for operation and to achieve high performance plasmas. Major issues are to achieve low outgassing, low particle recycling and a low impurity level. Implementation and optimisation of a systematic wall conditioning strategy was a major issue during the second operation campaign at the superconducting Wendelstein 7-X stellarator. W7-X was equipped with a graphite divertor and a first wall of stainless steel and graphite surfaces. Initial conditions for the campaign were provided by baking at 150°C which removed water and higher hydrocarbons. Intense hydrogen glow discharge cleaning (GDC) reduced residual impurities, such as CO and CH4. Final He-GDC removed hydrogen from the surfaces. Generally, the length of He-GDC was minimised to reduce sputtering at metal surfaces and redistribution of sputtered material. Since the magnetic field is continuously activated GDC cannot be applied between plasma discharges but only before and after the experiment time of a day when the field is deactivated. Instead, microwave based methods using ECRH are used and continuously optimized for conditioning between plasma discharges. This comprises pulse trains of intermittent short ECRH discharges with pumping intervals as well as single ECRH discharges at low density, both being operated in He. Following this strategy stationary plasma discharges have been achieved lasting for example 25 s at 3 MW heating power and constant density of 3 10^19 m^-3. The pulse length was only limited by the admitted heating energy. The progress of wall conditioning was monitored throughout the campaign by the normalized outgassing after plasma discharges. It decreased with cumulated discharge time by two orders of magnitude. In the next campaign boronisation will be available which is expected to further reduce the impurity level and particle recycling.

Speaker: Dr Rudolf Brakel (Max-Planck-Institut für Plasmaphysik, Greifswald, Germany)

745 Studies of the gas puff effect on edge plasma of Aditya tokamak using coupled DEGAS2-UEDGE code

Fuel neutral penetration and dynamics in the edge and scrape of layer (SOL) plasma region of tokamaks shape the plasma properties in these regions which play an important role in determining the core plasma confinement. Experiments in Aditya and Aditya-U tokamaks have shown that fuelling by periodic multiple gas puffs led to improved core plasma properties [1]. These experimental results warrants a detailed understanding of the edge and SOL plasmas during and after the gas puffs to understand the physics behind improvement of plasma properties. Modelling of edge and SOL plasmas of Aditya and Aditya-U tokamaks has been carried out using the coupled UEDGE and DEGAS2 code. Neutral hydrogen penetration into the Aditya [2] and Aditya-U plasmas has been obtained using the neutral particle transport code, DEGAS2 during the gas-puff. The modifications in plasma parameters in the SOL and edge regions due to these neutrals have been modelled using the UEDGE code, which is a 2D edge-plasma transport code. Both these codes are coupled to obtain the dynamics of edge and SOL plasmas during and after the gas-puffs of different magnitudes. The Aditya tokamak is operated with a poloidal ring limiter located at one toroidal location, whereas the Aditya-U tokamak is operated with a toroidal belt limiter on the high field side. Geometries of both limiter configurations are successfully integrated with both the codes, which are run for many discharges with different operational parameters. The coupled code has successfully reproduced the measured temporal evolution of Hα emission and the variations in density and temperature in the edge and SOL regions due to the gas puff. It has been observed that the gas puffs significantly modify the density and temperature profiles in the SOL and edge regions of Aditya and Aditya-U. The results show that the periodic gas-puffs of proper magnitudes can be used to control the SOL and edge plasma parameters in order to obtain improved core properties. [1] R. L. Tanna et al, NF 57, 102008 (2017). [2] R. Dey et al, NF 57, 086003 (2017).

Speaker: Dr Ritu Dey (Institute for Plasma Research)

RITU_summary_slide_FEC_2018.pdf

746 Studies of Ultrasonic and Phased array inspection NDT techniques on high thick SS316L welded joint mock-ups of fusion reactor components fabrication applications

Fusion reactor components manufacturing is mainly deals with Austenitic stainless steels with different type welding techniques and kind of weld structure joints. Thick steel like 40 mm & 60 mm plates are used mainly in the fabrication of vacuum vessel, divertor and other supporting structures with different weld joining techniques like Tungsten Inert Gas (TIG) welding, Narrow Groove TIG (NG-TIG) welding, Electron Beam Welding (EBW). The challenges arise to qualify the acceptance of welds inspection with NDT techniques. X-ray radiography examination shows limitation for thicker steels inspection and Liquid dye penetrant tests pose restriction for inside vacuum vessel welded joints due to penetrant chemicals exhibit outgassing effects. Ultrasonic and Phased Array examinations techniques have shown advantage over the conventional techniques for the welds inspection in case of thick plate steel welded structures by providing the size and shape of weld defects (Porosity, under cut, Cracks, inclusions etc) in critical positions and depth inspection in the welded joints. The present paper reports the examination studies carried out with conventional ultrasonic examinations (A-scan technique), Phased Array examination techniques on the different weld SS316L plate mock-ups. Weld mock-up coupons have been fabricated with different welding procedures (TIG, EB, and NG-TIG) and joint preparations such as butt and Narrow groove, T-weld joints of 40 mm and 60 mm thick plates of SS316L. Weld joints of T- type coupons have been fabricated with TIG welding and are examined with the conventional and Phased Array ultrasonic examinations. Calibration is implemented with known defect size and reference methodology with Phased Array ultrasonic inspection technique. The Phased array examination (PA, Angle beam phased array S-scan, 2.25 MHz probe), has shown superiority over the conventional Ultrasonic technique by revealing the minor size defects with mapped welded regions. However, the weld defects detected are well within the acceptable limits. The welded samples are inspected by X-ray radiography is compared and it is noted that the line defects and porosity conditions are not revealed. The present paper discusses the welding mock-ups tests like Calibration tests, NDT techniques methodology and results of the weld defects.

Speakers: Mr Kedar S BHOPE (Institute for Plasma Research , BHAT, Gandhinagar, -382428,Gujarat,INDIA), Mr Ramesh Kumar B Buddu (Institute for Plasma Research , BHAT, Gandhinagar, -382428,Gujarat,INDIA)

Summaryslide-Buddu-FIP-P8-18.pptx

747 TCV heating and divertor upgrades

The range and the reactor relevance of the TCV experiments are being enhanced by two sets of major upgrades. The first set includes the installation of neutral beam injection (NBI) and new Electron Cyclotron (EC) power sources, to heat the ions and vary the electron to ion temperature ratio, in plasmas with ITER relevant β values. A 15-30keV, 1MW, 2s tangential NBI system is operational on TCV since 2015. A second beam at 1MW, ~50keV, also tangential but opposite to the first beam, is foreseen to approach β limits, vary the applied momentum input and investigate suprathermal ion physics. For the EC power, two 0.75MW gyrotrons at the 2nd harmonic have been installed. The next step consists of two 1MW dual frequency gyrotrons (2nd and 3rd harmonics), one of which is being commissioned. The heating upgrades will raise the total heating power for high-density plasmas from 1.25 MW to 5.25 MW. The main element of the second set is an in-vessel structure to form a divertor chamber of variable closure, to reach relatively high neutral density and impurity compression and access reactor relevant divertor regimes for conventional or advanced divertor configurations. Graphite gas baffles will be installed to define a divertor and a main chamber region. The first set of baffles consists of 32 tiles on the high-field side (HFS) and 64 tiles on the low-field side (LFS), with geometry chosen on the basis of simulations performed using the SOLPS-ITER and EMC3-Eirene codes. The HFS baffles are expected to be effective for a wide range of divertor configurations, including snowflake and super-X divertors, yet keeping the plasma close to the inner wall for passive stabilization. The LFS tiles’ dimensions will be varied to modify the divertor closure. Control of the plasma, neutral and impurity densities, and He compression will be achieved by a combination of toroidally distributed gas injection valves, impurity seeding, and cryo-condensation pumps. Significant developments will be undertaken also in plasma diagnostics, to characterize the divertor plasma, measure power and particle deposition at the strike points, and obtain information on the detachment process. The possibility of installing dedicated divertor coils, made of high temperature superconductors, to expand the range of divertor configurations and improve their control, will be discussed.

Speaker: Prof. Ambrogio Fasoli (EPFL Swiss Plasma Center)

AF_IAEA2018_oneslide.pptx

748 Technology developments for ECRH system

The Gyrotron based electron Cyclotron resonance Heating (ECRH) system is used on tokamaks Aditya-U and SST-1. The ECRH system consists of High power Gyrotron, corrugated waveguide based transmission line and a quasi-optical launcher. The 42GHz Gyrotron delivers 500kW power for 500ms duration. This Gyrotron operates at ~ - 48kV beam voltage and +18kV anode voltage. This system draws around 20A beam current. This is a critical systems associated with high voltage power supply systems. A dedicated protection system is used to protect the Gyrotron in an event of fault. An ignitron based crowbar system removes the voltage within 10s and ensures the safe operation of Gyrotron. In order to operate the system with more reliability, power supplies and protection system are being upgraded indigenously. An advance thyristor based solid state crowbar is under development which will replace the ignitron crowbar system. A 20kV solid state crowbar has been developed and tested successfully. This system has been integrated with the existing anode power supply. The prototype crowbar at 30kV has also been tested successfully. A 50kV solid state crowbar has been designed and under development. An IGBT based solid state switch has been developed successfully which has been tested up to 18kV. This can replace the existing anode power supply which has slow rise time. This IGBT based switch facilitates the system for modulation. An advance launcher has been designed and under procurement. This launcher consists of two mirrors (one focusing and other plane) mounted on SS flange. The focusing mirror is fixed however the plane mirror can be steered in ultra-high vacuum (UHV) environment. The plane mirror is connected with two mechanisms for necessary movement in two directions. The system is designed such that to minimize the backless and give the precession movement with position indicator. This prototype launcher can be used as real-time feedback launcher with some additional modifications. The paper discusses about the technologies developed indigenously for the safe, reliable and accurate operation of ECRH system on tokamaks.

Speaker: Dr Braj Kishore Shukla (Institute for Plasma Research)

749 The effects of magnetic topology on the SOL island structure and turbulence transport in the first divertor plasma operation of W7-X

Wendelstein 7-X (W7-X) was operated successfully with the first divertor plasma in the operation phase 1.2a (OP1.2a). A new combined probe head, which consists of Langmuir probe pins, Mach probe, ion sensitive probe (ISP), differential coil and a tri-axial pick-up coil, is able to measure the edge plasma profiles (T$_e$,n$_e$,ϕ$_f$,M$_∥$), magnetic field, poloidal and radial turbulence structures. The plasma parameters in three magnetic configurations (KJM, EJM, FTM) are measured by the new combined probe head, which are in good agreement with the island structure calculated by field line tracer. In configuration of EJM, the floating potential has a negative value around the radial region from 6.065 m to 6.071 m, where the island center is located at R = 6.068 m and R$_{LCFS}$ = 6.035 m along the path of probe. Within this region, the electron pressure reveals a platform, the parallel Mach number exhibits a symmetric profile, and the radial particle flux driven by turbulence reduces to a relatively low level. However, outside this region the particle flux is extremely high on both sides. The high particle flux is dominated by the broadband turbulence between 80 to 120 kHz, while the inner radial region with low particle flux is driven by the turbulence below 25 kHz. It should be noticed that the high turbulent particle flux is located in the region with large gradient of electron density, indicating that the transport could be driven by the instability caused by density gradient. Additionally, a large positive floating potential is observed in all the three configurations, which has strong dependence on line integrated density. The mechanism of this positive floating potential has been studied with a simple model, suggesting a large gradient of parallel electron density between upstream and divertor region. In this work, the turbulence modes and their propagations are compared for these three magnetic configurations.

Speaker: Dr Shaocheng Liu (Institute of Plasma Physics Chinese Academy of Sciences)

750 The ITER baseline scenario investigated at ASDEX Upgrade

At ASDEX Upgrade experiments have been performed, in which important features of the ITER baseline (ITER BL) scenario are matched or imitated. A crucial property of the ITER BL scenario is the combination of $q_{95}=3$ with strong plasma shaping, which leads to ELM frequencies ($f_{ELM}$) as low as 10Hz, while the ELMs are very large. One consequence of the low $f_{ELM}$ is that access to ITER-relevant collisionalities has been hindered as a strong deuterium (D) gas puff is required to control the W-concentration. The large D gas puff is also suspected [1] to diminish the energy confinement leading to $H_{98(y,2)}$-factors in the range of 0.85 at the relevant $\beta_N=1.8$, while the Greenwald fraction ($f_{GW}$) is at relevant levels (~0.85). In order to achieve the desired performance, strategies for confinement improvement are investigated, such as increasing $q_{95}=3$ while decreasing the D gas puff or applying N-seeding. However, these routes do not seem to be able to recover sufficient confinement. While exploring strategies to go towards low $\nu^\ast$ in the ITER BL scenario, the use of MP-coils yielded a breakthrough allowing for an almost match of ITER collisionalities, i.e. $\nu^\ast/\nu^\ast_{ITER}\approx3$, and for a clear decoupling of ion and electron heat fluxes. The low collisionalities were obtained by density pump-out of more than a factor of 2, while the confinement is almost not diminished. When extrapolating $\beta_N$ of such a phase heated with NBI and ICRH to ITER relevant values, sufficient confinement is expected. At the same time ELMs are either very small or even suppressed in some cases. However, when MP-coils are applied to the high density ITER BL scenario matching $f_{GW}$ instead of $\nu^\ast$, only a small pump-out effect (~10%) and almost no effect on the ELM size is observed. The density dependence of the MP-coil effectiveness is consistent with [2]. In order to mitigate ELMs at high density, pellet pace making, strong gas puffing or a slight shape or position change proved to be more efficient than the application of MP coils. It is remarkable that corresponding high density discharges in helium behave very similarly, w.r.t. the negligible MP coil effect and the accomplishment of small ELMs at large neutral helium density. [1] J. Schweinzer et al, NF 56, 2016; [2] N. Leutholt et al, PPCF 59, 2017

Speaker: Dr Thomas Pütterich (Max-Planck-Institut für Plasmaphysik)

Summary_Slide.pdf

751 The LTX-beta Research Program and First Results

The research program for LTX-beta, the upgrade to the Lithium Tokamak Experiment, combines lithium walls to produce gradient-free temperature profiles and stabilize ion and electron temperature gradient-driven modes, with approaches to stabilization of density gradient-driven modes, such as the trapped electron mode (TEM). Candidate stabilization mechanisms for the TEM include sheared flow stabilization, which will be tested on LTX-beta using neutral beam induced rotation. The goal is to reduce anomalous transport in a low aspect ratio tokamak. The upgrade will approximately double the toroidal field of LTX-beta (to 3.4 kG) and plasma current (to 150 – 175 kA), compared to LTX. Upgrades to the diagnostic set are in the areas of equilibrium, core transport, scrape-off layer (SOL) physics, and plasma-material interactions. Neutral beam injection at 20 kV, 30 A will be added in spring 2018, using a neutral beam system provided by Tri-Alpha Energy. A 9.3 GHz, 50 kW, short-pulse (5-10 msec) magnetron will be available later in 2018 for electron heat pulse propagation experiments. New lithium evaporation sources allow between-shots recoating of the walls. LTX-beta is a collaborative effort, with major participation from Oak Ridge and Lawrence Livermore National Laboratories (ORNL and LLNL), as well as the University of California at Los Angeles (UCLA). ORNL and the University of Tennessee will focus on spectroscopic improvements, and edge plasma/plasma-material interaction (PMI) analysis. LLNL plans research in the areas of SOL transport and plasma-surface interactions with lithium and tin. UCLA is upgrading the LTX profile reflectometer for high radial wavenumber backscattering. The 1 mm UCLA interferometer system will also be upgraded to probe low perpendicular wavenumber density fluctuations. The LTX-beta research program will be discussed, and initial operation of the upgraded device will be described. This work supported by USDoE contracts DE-AC02-09CH11466, DE-AC05-00OR22725, and DE-AC52-07NA27344.

Speaker: Richard Majeski (Princeton Plasma Physics Lab)

EX_P8_29-majeski-summary.pdf

752 Time-Dependent Runaway Simulations: Ampere-Faraday Equations Implemented in CQL3D

The runaway electron distributions driven by a large toroidal electric field Etor induced by the drop in the temperature profile due to disruption or pellets are comprehensively simulated by the 3D Fokker-Planck solver CQL3D [1], recently coupled to the Ampere-Faraday (A-F) equations. The evolution of the toroidal current in a plasma occurs on a resistive time scale tr, which is typically of the order of seconds in present tokamaks. From the Faraday EM equation, Etor is proportional to the time derivative of the poloidal magnetic field, which, from the Ampere equation is proportional to the toroidal current. Thus, Etor rapidly increases due to rapid temperature drops, to prevent change in the toroidal current faster than tr. In simulations with KPRAD [2] of neon pellet injection into a DIII-D shot, Te drops from 2 keV to 10 eV in 0.1 msec and Zeff increases 1 to 4, giving that Etor increases 3500X to 0.8 V/cm. As described in [3], this places much of the tail electron distribution beyond the Dreicer runaway velocity, giving so-called "hot-tail runaways" which for a time are the dominant source of runaways, more so than the knockon source. In this prior calculation, performed for a single flux surface, the toroidal current density is held constant, on the basis that tr is large. Most of the initial current can be converted to runaway current, which is then dangerous, particularly for ITER. The A-F model recently implemented in CQL3D, taking into account the time-development of the full-plasma-width Etor on time-scales of order tr, applies an iterative technique for the Etor previously developed for a different application [4], maintaining the implicit-in-time evolution of CQL3D. The degree of runaway current formation is reduced in A-F augmented CQL3D, but the basic mechanism of "hot-tail runaways" [3] remains a dominant contribution to the runaway electrons at early times after the Te drop. Supported by USDOE grants ER54744, DE-SC0016452 (GA SCREAM), and DE-FG02-95ER54309 (GA Theory). [1] R.W. Harvey and M. McCoy, "The CQL3D Fokker Planck Code", www.compxco.com/cql3d.html. [2] D.G. Whyte, T.E. Evans et al., Proc. 24th EPS Conf., Berchtesgaden, Germany (1997). [3] R.W. Harvey, V.S. Chan, S.C. Chiu, T.E. Evans, M.N. Rosenbluth, and D.G. Whyte, Phys. Plasmas 7, 4590 (2000). [4] K. Kupfer R.W. Harvey, et. al., PoP 3, 3644 (1996).

Speaker: Dr R.W. (Bob) Harvey (UsCompX)

Harvey_TH_P8-18_Summary_Slide.pdf

753 Investigations of the role of neoclassical transport on W7-X

Speaker: Dr Novimir Pablant

Pablant.N-EX-C-Abstract_v07.pdf

Pablant.N-EX-C-Preprint_v00.pdf

Pablant.N-EX-C-Synopsis_v08.pdf

754 First results of infrared thermography on WEST

Speaker: Mr Michael Houry (CEA)

755 Mutual Interactions between Zonal Flows and Turbulence Driven Magnetic Islands

Speaker: Olivier Agullo (Aix-Marseille Université)

756 First results of LH coupling and current drive in WEST full metallic environment and commissioning of the new ELM resilient ICRF antenna

Speaker: Dr Annika Ekedahl

Abstract_IAEA2018_RF_WEST.pdf

IAEA_poster_2018_RF_WEST_V3.pdf

WH_synopsis_IAEA2018_RF_WEST1.pdf

757 Overview of the Divertor Tokamak Test Facility Project

The Divertor Tokamak Test Facility (DTT) is a new tokamak whose
construction has recently been approved by the Italian government. DTT
will be a high field superconducting toroidal device (6 T) carrying
plasma current up to 6 MA in pulses with length up to 100s, with an
up-down symmetrical D-shape defined by major radius R=2.10 m, minor
radius a=0.65 m and average triangularity 0.3. The main role of DTT is
to contribute to the development of a reliable solution for the power
and particle exhaust in a reactor, a challenge commonly recognised as
one of the major issues in the road map towards the realisation of a
nuclear fusion power plant. Following the project approval, since June
2017 the design review of DTT has started. This paper will present the
device by summarizing its main physics goals and the present status of
the design.

Speaker: Piero MARTIN (Consorzio RFX)

758 Magnetic configuration and plasma start-up in the WEST tokamak

Speaker: Dr Eric Nardon

759 Graphene-based Hall Sensors for DEMO Magnetic Diagnostics

Speaker: Inessa Bolshakova (Lviv Polytechnic National University)

16:10 Coffee Break

EX/9-TH/7 Divertor & Exhaust Physics

760 First divertor physics studies in Wendelstein 7-X

Wendelstein 7-X (W7-X) went successfully into operation in 2015 [1-4]. With a 30 cubic meter volume, a superconducting coil system operating at 2.5 T, and steady-state heating capability of up to 10 MW, it was built to demonstrate the benefits of optimized stellarators at parameters approaching those of a fusion power plant. Operation phase 1.2a (OP1.2a), which was performed in the second half of 2017, was the first operation phase with a full complement of plasma-facing components, including 10 passively cooled fine-grain graphite divertor units. These have the same geometry as the water-cooled steady-state carbon-fiber-composite divertor units that will be in operation in the early 2020’s (Operation Phase 2, OP2). They allowed the start of a divertor research program, but at pulse lengths limited to about 80 MJ of pulse energy, eg. 20 seconds at 4 MW. The first divertor results in W7-X are very encouraging. For the foreseen magnetic configurations, the convective heat loads were deposited in the divertor, with strike line patterns closely resembling those predicted from edge modeling. Using trim and sweep coils, it was possible to eliminate the lowest order resonant field errors (n/m=1/1), and thereby symmetrize the heat loads onto the divertor units. High densities were achieved first in helium and then, using the pellet system, in hydrogen (n_e0 up to 0.9x10^20 m^-3). With the higher hydrogen densities came the most remarkable divertor result of the OP1.2a campaign: Stable and reproducible heat flux detachment. The infrared cameras show a divertor heat flux reduction of an order of magnitude in all 10 divertor modules. During detachment, no degradation of core confinement was seen. In addition to these results, several other results related to edge- and divertor physics in W7-X will be presented, including enhanced edge radiation by injection of medium-Z impurities, and operation in magnetic configurations mimicking those of long-lived high-performance discharges foreseen for OP2. References [1] T. Klinger et al. Plasma Phys. Controlled Fusion 59 014018 (2017) [2] H.-S. Bosch et al., Nuclear Fusion 57, 116015 (2017) [3] R. C. Wolf et al., Nuclear Fusion 57 102020 (2017) [4] T. Sunn Pedersen et al., Physics of Plasmas 24 055503 (2017)

Speaker: Prof. Thomas Sunn Pedersen (Max Planck Institute for Plasma Physics)

IAEA_single_slide.pptx

Pedersen_IAEA_2018_16x9_v15.pptx

761 Demonstration of Power Exhaust Control by Impurity Seeding in the Island Divertor at Wendelstein 7-X

Effective power exhaust by impurity seeding and its dependence on the gas species used was demonstrated in island divertor configurations for the first time at Wendelstein 7-X (W7-X).
A systematic set of experiments has been conducted during the first island divertor campaign which show that switching from Neon (Ne) to nitrogen (N2) as seeding gases enables switching from global to more localized edge cooling. In case of Ne seeding significant enhancement of edge radiation with slow decay after end of the injection is observed due to the high recycling properties of this noble gas. The N2 seeded discharges show immediate response of local plasma parameters at the divertor target correlated to the puff duration. Fast Te recovery and drop of Prad after end of the puff suggest a rather low recycling coefficient for this impurity species. These effects are analysed by 3D modeling with EMC3-EIRENE for high and low recycling coefficients.
The impact of the 3D edge magnetic structure on radiation is investigated experimentally by changing island size and connection lengths with the island control coils in the 5/5 configuration for scenarios with ne~1.8e19m-3 at PECRH~2.9MW. A 22ms Ne puff causes enhancement of Prad by ~1.6MW. Application of full control coil currents, Icc=2.5kA, yields a reduction of intrinsic Prad level from ~0.7MW to 0.3MW and an reduced increase of Prad by 1.1MW in response to Ne seeing. The change of island geometry results in a faster decay of total impurity radiation measured by an effective time constant \tau_{Prad}.
The presented findings on power exhaust control by impurity seeding in the W7-X island divertor are the basis for implementing radiative cooling as means to protect plasma facing components as performance levels at this new HELIAS stellarator are rising. With increasing performance, equilibrium effects will impact on the 3D magnetic structure, which is addressed by equilibrium reconstruction with V3FIT and the 3D MHD code HINT. Investigation of the link between the magnetic structure, the appropriate gas species, the injection location and the impurity transport is of critical importance for the high level goal of HELIAS divertor optimization. The experimental and numerical studies presented here represent a first-time consistent exploration of this field in the new island divertor configuration.

Speaker: Dr Florian Effenberg (Department of Engineering Physics, University of Wisconsin - Madison)

FEC_IAEA_Talk_2018_Effenberg.pdf

Summary_Slide_EX92_Effenberg.pdf

762 Progress in DIII-D Towards Validating Divertor Power Exhaust Predictions

Understanding of divertor heat load and its control in fusion reactors has been critically advanced in DIII-D radiative power exhaust experiments corroborated with state-of-the-art 2D fluid simulations. UEDGE simulations indicate that the non-linear interaction between the divertor electron temperatures and drifts can drive a bifurcation of the divertor solution between attached and detached branches. This mechanism provides an explanation for the experimentally observed step-like transition from strongly attached to well detached divertor conditions with increasing plasma density, as measured by Thomson scattering in plasmas with the grad-B-drift towards the X-point (fwd. BT). Analysis of the new extreme ultraviolet (EUV) spectroscopy shows that in detachment with D2-injection in fwd. B, the resonant CIV (154.9 nm) line dominates the radiated power and peaks next to the X-point. In contrast, operating with the grad-B-drift away from the X-point (rev. B), the radiated power peaks in front of the outer target and is dominated by the deuterium Ly-alpha (121.5 nm). Fluid simulations with UEDGE qualitatively reproduce the relative intensity of the emitting lines and regions in both field configurations. However, the simulations predict the radiation to be about a factor of 3 more localized than measured, indicating an under prediction of the transport mechanisms expanding the radiating volume. Work supported by the US DOE under DE-FC02-04ER54698 and DE-AC52-07NA27344, and LLNL LDRD project 17-ERD-020.

Speaker: Dr Aaro Jaervinen (Lawrence Livermore National Laboratory)

Presentation for the Divertor & Exhaust session EX_9_3_Jaervinen_IAEA_26Oct2018.pdf (Protected)

Summary slide Jaervinen_IAEA_2018_summary_slide_2.pdf Jaervinen_IAEA_2018_summary_slide_2.pptx

763 Predicting Scrape-Off Layer profiles and filamentary transport for reactor relevant devices

This paper discusses a statistical framework that relates the fundamental physics of Scrape-Off Layer (SOL) L-mode and inter-ELM filaments with the profiles they generate in magnetic confinement devices. This work reviews the theoretical and numerical work recently carried out at CCFE in support of the statistical framework and compares it with experimental measurements obtained with innovative techniques on MAST and JET. The emphasis will be on extrapolating the knowledge gained to future machines like ITER and to advanced divertor solutions. With a semi-analytic treatment using minimal computational resources, the framework predicts and interprets the experimental profiles and of the turbulence statistics on the basis of simple properties of the filaments, such as their radial motion and their draining towards the divertor. Filaments are described as independent events and modelled with a wave function of amplitude and width statistically distributed according to experimental observations and evolving according to fluid equations. The framework predicts that radially accelerating filaments, less efficient parallel exhaust (e.g. due to interaction with neutrals) and also a statistical distribution of the radial velocities can contribute to induce flatter profiles in the far SOL and therefore enhance plasma-wall interactions. It also suggests that profile broadening at high fueling rates, potentially harmful for ITER, can be caused by interactions with neutrals in the divertor or at the wall or by a significant radial acceleration of the filaments. The results of the framework are backed up by systematic experimental comparison with measurements taken on JET and MAST using Langmuir probes and fast visual cameras. Advanced machine learning algorithms were developed and deployed, including Bayesian analsysis of time traces and convolutional neural networks applied to filament identification in images. In all the cases treated, the theoretical prediction matched the experimental data within errorbars. In addition, 3D simulation in realistic geometry were performed with the 3D SOL turbulence code STORM, with the aim of assessing the validity of the framework assumptions. The mechanisms governing the interaction of pairs of filaments and the dynamics of high beta, inter-ELM like, filaments were investigated and employed to improve the statistical framework.

Speaker: Prof. Fulvio Militello (Culham Centre for Fusion Energy)

Presentation_Militello_IAEA_16_9_ver2.pptx

Summary_slide_Militello.pptx

764 Study of passively stable, fully detached divertor plasma regimes attained in innovative long-legged divertor configurations

Passively-stable fully detached divertor regimes have been found in numerical modeling of divertor configurations with radially or vertically extended, tightly baffled, outer divertor legs, with or without a secondary X-point in the leg volume [1]. Simulations carried out with the tokamak edge transport code UEDGE [2] using the base parameters of the ADX tokamak design [3] show that long-legged divertors provide up to an order-of-magnitude increase in the peak power-handling capability compared to conventional divertors, and a fully detached plasma state can be passively maintained over a wide range of parameters. In the simulations, the radial transport in the scrape-off layer is set to reproduce profiles observed in the experiment, which includes 'shoulders' indicative of main-chamber recycling phenomena [4]. In the UEDGE model used here, strong radial transport is assumed to occur in the outer divertor leg as well, leading to plasma predominantly recycling on the divertor leg outer sidewall. Analysis of simulations shows that the detachment front location is set by the balance between the power
 entering the divertor leg and the losses to the walls of the divertor channel.
 Therefore, for a fixed level of power exhaust, the location of the detachment front is insensitive to the divertor leg length - as long as the leg length exceeds the front location. The key physics for attaining the passively stable, fully detached regime involves an interplay of strong convective plasma transport to the divertor leg outer sidewall, confinement of neutral gas in the divertor volume, geometric effects possibly including a secondary X-point, and atomic radiation. In response to variation of model assumptions (magnitude of anomalous radial transport, impurity radiation, neutral transport model, geometry of plasma-facing components), the overall divertor plasma behavior remains qualitatively similar: a stable fully detached regime is maintained, lending confidence in the modeling results. [1] M.V. Umansky et al., Phys. Plasmas 24, 056112 (2017); [2] B. LaBombard et al., Nucl. Fusion 55, 053020 (2015); [3] T. D. Rognlien et al., J. Nuc. Mat. 196, 347-123 (1992); [4] B. LaBombard et al., Nucl. Fusion 40, 2041 (2000); *Work supported by US DoE contract DE-AC52-07NA27344 and cooperative agreement DE-SC0014264.

Speaker: Dr Maxim Umansky (Lawrence Livermore National Lab)

IAEA_mvu.v6.pdf

mvu_iaea_2018.v7f.pptx

mvu_summary_2018.v1.pdf

765 Erosion, Screening, and Migration of Tungsten in JET Equipped with Tungsten Divertor

W is the plasma-facing material of the JET-ILW divertor. W erosion by plasma and impurity impact determines the components lifetime as well as can influence the plasma performance by the W influx into the confined region. Certainly, the W screening by the divertor and the W transport into the plasma determines the W core content, but the W source itself impacts the process. Its quantification is essential to understand the interplay between the W impurity and the plasma. The JET-ILW provides access to a large set of W erosion-determining parameters permitting a detailed description of the source in the divertor closest to the ITER one. (a) Effective sputtering yields and fluxes as function of impact energy of intrinsic (Be,C) and extrinsic (Ne,N) impurities as well as hydrogenic isotopes (H,D) are determined. This includes the interplay between intra- and inter-ELM W sources caused by the flux and energy distributions in these phases. The threshold behavior and the spectroscopic composition analysis provide an insight in the dominating species and phases causing the erosion. (b) The interplay between net and gross W erosion source will be elaborated considering prompt re-deposition, thus, the return of W to the surface within one Larmor radius, and surface roughness, thus, the difference between smooth bulk-W and rough W-coating components. Both effects impact the balance equation of local W erosion and deposition. (c) Post-mortem analysis reveals the campaign-integrated net migration path identifying the W transport to remote areas. The transport is related to the plasma regime, e.g. H-mode with attached divertor and high impact energies of impinging species or detached operation, as well as to the magnetic configuration, e.g. corner with geometrical screening of W or ITER-like vertical target. (d) The influence of parameters like surface temperature on the erosion, including the role of chemically assisted physical sputtering, is covered. JET-ILW permitted access to net W erosion in one magnetic configuration within a series of 151 subsequent discharges. Comparison of spectroscopy in the intra-ELM and inter-ELM phases with post-mortem analysis of marker tiles provided a set of gross and net W erosion. ERO code simulations could reproduce the pattern as well as confirm high prompt W re-deposition factors of more than 95% for the intra-ELM phase.

Speaker: Dr Sebastijan Brezinsek (Forschungszentrum Jülich)

IAEA_2018_Brezinsek_final.pptx

Single_Slide_Brezinsek.pptx

Single_Slide_Brezinsek.pptx

Saturday, 27 October

EX/10-TH/8 Transport

766 Isotope effect on impurity and bulk ion particle transport in the Large Helical Device

Isotope effects of the ion particle transport both for carbon impurity and bulk ions are investigated in Large Helical Device (LHD) in a condition decoupled from electron particle transport. Better particle confinement for both impurity and bulk ions are observed in deuterium plasmas than in hydrogen plasmas. The following findings are presented in this paper. 1) Carbon impurity density gradient is negative (peaked profile with inward convection) inside the internal transport barrier (ITB) region in the deuterium (D) plasma, while it is positive (hollow profile with outward convection) in the hydrogen (H) plasma. 2) The decay time of D ion density measured with bulk charge exchange spectroscopy inside the plasma after the D pellet injections is longer than that of H ion density after the H pellet injections by a factor of 1.4. The difference in the decay time of H and D in the H-D mixture plasma strongly suggests that there should be a difference in deuterium and tritium (T) particle transport in the D-T mixture plasma in ITER.

Speaker: Dr Katsumi Ida (National Institute for Fusion Science)

2018_10_27_IAEA-FEC_EX10_1_Ida V3.pptx

IAEA-FEC summary Ida.pdf

767 3D structure of density fluctuations in T-10 tokamak and new approach for current profile estimation.

Previous correlation reflectometry investigations in T-10 tokamak revealed the existence of several density fluctuation types and strong radial and poloidal variation of their amplitudes and correlation properties. This paper presents the new measurements of the 3D spatial distributions of the amplitudes, radial correlation lengths and long range correlations along the field lines of the different turbulence types. Experiments were carried out in OH and ECRH heated discharges. The density fluctuations were measured by correlation reflectometry using ordinary mode probing and new T-10 antenna set with four horn arrays distributed toroidally and poloidally over tokamak torus. Experiments confirmed previously found strong poloidal amplitude asymmetry of Broad Band (BB) and Quasi-Coherent (QC, typically 110-170 kHz) and uniform poloidal distribution of Stochastic Low Frequency (SLF, 0-50 kHz) density fluctuations. Presence of those turbulence types was also proved by measurements with Heavy Ion Beam Probe. Radial correlation measurements were made at four poloidal angles to understand the poloidal dependence of the radial correlation length for different fluctuation types. The significant decrease of the radial correlation lengths with towards high magnetic field side was observed for all turbulence types. The long range correlations along the field lines were measured by reflectometers in two cross-section separated by 1/4 of torus. Reflectometers have the same frequency thus provide reflection from the same magnetic surface. Reflection radii are chosen by frequency variation of the launched wave from shot to shot in a series of reproducible discharges. Measurements were carried out at low and high magnetic field side with two currents and simultaneous reverse of toroidal magnetic field and plasma current. Resonance radii were also calculating using 3D tracing of the magnetic field line and demonstrate good agreement with experiments. These results allow to propose the new approach for the current profile estimation in tokamaks.

Speaker: Dr Vladimir Vershkov (NRC "Kurchatov institute")

EX_10_2_FEC 2018_Vershkov.ppt

IAEA2018_Vershkov_Final.pdf

Slide_EX_10_2.pdf

768 Gyrokinetic XGC1 Simulation Study of Magnetic Island Effects on Neoclassical and Turbulence Physics in a KSTAR Plasma

We perform gyrokinetic simulations to study the effects of a stationary magnetic island on neoclassical and turbulence physics. A KSTAR L-plasma condition is employed for the simulations. Through the simulations, we aim to understand the underlying physical mechanisms of poloidal flows and fluctuations around a stationary (2,1) magnetic island, which were observed in a recent KSTAR experiment using 2D ECEI diagnostics [M.J. Choi et al., Nucl. Fusion 57, 126058 (2017)]. From the simulations, it is found that the magnetic island can significantly enhance the equilibrium ExB flow. The corresponding flow shearing is strong enough to suppress a substantial portion of ambient micro-instabilities, particularly $\nabla T_e$-driven trapped electron modes. This implies that the enhanced ExB flow can sustain a quasi-internal transport barrier for $T_e$ in an inner region neighboring the magnetic island. The enhanced ExB flow has a (2,1) mode structure, which shows a finite phase difference with the mode structure of the magnetic island. It is shown that the flow shear and fluctuation suppression patterns the simulations imply are consistent with the ECEI observations on the KSTAR experiment.

Speaker: Dr Jae-Min Kwon (National Fusion Research Institute)

jkwon IAEA 2018.pptx

Kwon - IAEA summary.pptx

Kwon - IAEA summary r1.pptx

769 Explaining Cold-Pulse Dynamics in Tokamak Plasmas using Local Turbulent Transport Models

This work demonstrates that cold-pulse phenomena in tokamak plasmas can be fully explained by local transport models [1], including the existence of core temperature inversions at low density and disappearance at high density, thus resolving an enigmatic but universal transient transport phenomenon that has challenged the standard local model of transport for more than twenty years [2]. The TRANSP power balance code coupled with the quasilinear transport model TGLF-SAT1 [3], with a new saturation rule that came about as a consequence of cross-scale coupling physics and that captures the nonlinear upshift of the critical gradient, are shown to fully describe the cold-pulse phenomenology after laser blow-off injections in the Alcator C-Mod tokamak. By means of experimentally-constrained self-consistent modeling of cold-pulse experiments, this work provides the strongest evidence to date that the existence of non-local transport phenomena may not be necessary for explaining the behavior and timescales of cold-pulse experiments in tokamak plasmas. This work was supported by U.S. Department of Energy Award No. DE-FC02-99ER5451, using Alcator C-Mod, a DOE Office of Science User Facility. P.R.F. was also supported by U.S. Department of Energy Award No. DE-SC0014264 and a La Caixa Fellowship. [1] P. Rodriguez-Fernandez et al 2018 (accepted, Phys. Rev. Lett.) [2] K. Ida et al 2015 Nucl. Fusion 55 013022 [3] G.M. Staebler et al 2017 Nucl. Fusion 57 066046

Speaker: Mr Pablo Rodriguez-Fernandez (UsPSFC)

PRF_IAEAFEC_v1.pdf

PRF_summ_slide.pdf

770 Benchmarking of Full-f Global Gyrokinetic Modeling Results Against the FT-2 Tokamak Doppler Reflectometry Data Using Synthetic Diagnostics

The fast linear (Born approximation) version of the X-mode Doppler reflectometry (DR) synthetic diagnostics is developed in the framework of the ELMFIRE global gyrokinetic modeling of the FT-2 tokamak ohmic discharge. The DR signal frequency spectra and the dependence of their frequency shift and shape on the probing antenna position are computed and shown to be similar to those measured in the high magnetic field side probing DR experiment at the FT-2 tokamak thus demonstrating a correct reproduction of the electric field behavior in the FT-2 tokamak by the ELMFIRE GK code. However, the computed and measured dependences of the DR signal power on the antenna position characterizing the «poloidal correlation lengths» appear to be different presumably due to underestimation of the small-scale TEM turbulence component in the measurement region by the code. The fluctuation poloidal velocities and the geodesic acoustic mode (GAM) amplitudes are determined using DR experiment and synthetic diagnostics and shown to be close within a 20% accuracy, whereas the GAM frequency spectra demonstrate clear differences. In the case of multi-frequency probing the cross-correlation function of radial correlation DR obtained in the experiment is shown to be a factor of four narrower than the computed one due to the phase modulation of the DR signal by long-scale turbulent density fluctuations. A comparison to the alternative version of the DR synthetic diagnostics based on the nonlinear full-wave modelling is also performed. It is shown that in spite of a better description of the radial correlation DR data nonlinear synthetic diagnostics fails to reproduce the DR frequency spectra as opposed to linear version of the synthetic diagnostic. The nonlinear effects in the DR spectra formation are shown to be responsible for this under conditions of small scale turbulence level underestimation by the GK code.

Speaker: Mr Alexey Altukhov (Ioffe Institute)

Altukhov_FEC_RCDR1.pdf

FEC18_Altukhov.ppt

RCDR_synth_slide.pptx

10:15 Coffee Break

EX/11-SEE/3-PD Stability, Environmental, Post Deadline

771 Origin of Harmonics of Drift Tearing Mode in ADITYA tokamak

Tearing modes play pivotal role in determining two of the most critical parameters for tokamak operation, namely plasma confinement and disruption. They have been extensively studied both theoretically and experimentally, as controlling them is foremost priority for every tokamak, including ITER and future large size tokamaks. Coupling of tearing modes with drift wave is a common phenomenon observed in all tokamaks, resulting in drift tearing modes. Multiple drift tearing modes have also been observed in a bunch of experiments. However, these modes have been identified as different modes with different poloidal (m) and toroidal (n) mode numbers. In ADITYA as well as ADITYA Upgrade tokamak, the frequency spectra of Mirnov signal show multiple frequency bands corresponding to drift tearing modes. Interestingly, the higher frequencies have been precisely found to be integral multiples of the fundamental frequency. Further analysis reveals that these frequencies don’t belong to different modes but harmonics of a single mode. These harmonic frequencies also reflect significantly in the density as well as impurity radiation. We have also found that the occurrence of these harmonics is strongly correlated with the presence of runaways in the plasma. The origin of these harmonics and their operational regime will be explained in this paper. The role of runaway electrons in manifestation of these harmonics is also proposed.

Speaker: Ms Harshita Raj (Institute for Plasma Research)

FEC18_Harshita.pptx

Summary Slide_HR.pptx

772 Effect of multiscale interaction between an m/n=2/1 mode and micro instabilities on transport of KSTAR plasmas*

Tokamak plasmas often encounter non-axisymmetric magnetic topology due to unavoidable magnetohydrodynamic (MHD) instabilities and/or external magnetic perturbation. Transport with non-axisymmetric perturbed equilibrium can be very complicated due to various multiscale interactions between a large scale MHD instability and small scale micro instabilities. This paper reports experimental observations and analyses of two distinguishing multiscale interactions. First, a multiscale interaction between the stationary large m/n=2/1 magnetic island and turbulence through profile modification has been identified using simultaneous 2-D measurements of electron temperature (Te) as well as turbulence and their flow profiles. A significant increase of Te turbulence is only observed near the X-point, while it is not observed both in inside and outside of the magnetic island near the O-point possibly due to the strong flow shear. The increased turbulence and Te gradient lead to the violent minor disruption of the plasma. In addition, a small amplitude m/n=2/1 mode can generate a modified spectrum of micro instabilities. The Doppler shift analysis of the measured frequencies of the modes revealed the nonlinear mode coupling among the m/n=12/6 main mode, the m/n=10/5 and m/n=14/7 side lobes, and the m/n=2/1 mode. These coupled modes appear to degrade the tokamak plasma confinement significantly without the violent disruption event. *This work is supported by the KSTAR research project funded by Korea Ministry of Science and ICT

Speaker: Dr Minjun J. Choi (National Fusion Research Institute)

minjun_FEC_pt_v7.pdf

summary_slide.pdf

summary_slide.pptx

773 Future Possibility of Carbon Sequestration by Biomass-Fusion Hybrid Systems & Economic Performance of Fusion Power Plant on Future Deregulated Electricity Market & Techno-economic analysis of biodiesel and hydrogen production via Fusion-Biomass Hybrid Model

A. This paper proposes a new and innovative fusion energy application in the emissions trading market based on the combination with biomass processing. An endothermic biomass conversion reaction of charcoal making process, or dry distillation; (CH1.6O0.6) = C+0.4H2+0.6H2O-451kJ (where biomass is assumed to be woody including large fraction of lignin.) can convert fusion energy obtained as high grade heat into carbon. The product solid char is separated and can be stored as it is or sintered. This biomass-fusion hybrid system will provide an innovative carbon sequestration method that originally is recovered from atmosphere by the photosynthesis by plants. What this system provides is the isolation of CO2 from the earth cycle including fossil combustion, and stabilizes it as solid carbon, and “sells” in the emissions trade market. If the values of the electricity and emission credits are similar to those currently observed, total sales, i.e. chance to return the investment for fusion would be similar. While competition in the clean electricity market in the future is anticipated to be tough, CCS market can provide significantly larger capacity because no other alternative technologies are known other than the underground storage. In this emissions credit market, fusion has fewer competitors that may have limiting siting and environmental constraint. Because transport, some industrial and residential heat sectors unavoidably release CO2, net negative emission by human activity with biomass is inevitable. This new fusion-biomass hybrid can provide net negative emission not only for electricity, but for all kinds of CO2 sources, and suggests the solution to return the CO2 concentration to the age before the industrial revolution. This study proposes an innovative option of fusion application that could potentially be larger and more important than electricity generation, and justifies the investment of fusion development that could be recovered from the future market. B. The economic performance of steady-state fusion power plants on future deregulated electricity markets was quantitatively analyzed for the first time with a newly constructed Simplified PJM Market Model. The results showed that (i) discussions based on simple levelised cost of electricity are insufficient for deregulated markets and (ii) the unplanned outage frequency target should be lowered to 0.3 times/year on deregulated market to achieve economic rationality of fusion power plants. Conventionally, the development strategies for fusion power plants came from extrapolation of past fission plant installation trends. However, due to the rapid transformations of the markets around the world, the future electricity markets will be significantly different from that of half a century ago. The fusion development strategies shall be revised accordingly: conventional measures such as levelised cost of electricity (LCOE) may no longer be applicable to future fusion power plants. To quantitatively analyze the economic performance of steady-state fusion power plants on future deregulated electricity markets, Simplified PJM Market Model that incorporates three Energy Market, Imbalance Fee and Ancillary Service Market was constructed. A steady-state fusion power plant with 1,200 MW electrical output (2,801 MW fusion) was assumed. The net present values (NPVs) of 40 years of plant operation were calculated with the discount rate of 1.7%. A sensitivity analyses were conducted for the unplanned outage frequency from 0.001 to 0.00001 times/hours. The economic performance of fusion power plant showed higher sensitivity to the unplanned outage frequency on deregulated market. The NPV of fusion plant on deregulated market would be devaluated from +368 million USD to -741 million USD when the unplanned outage frequency rises from 10-5 per hour to 10-4 per hour, while on conventional market, the devaluation would be only from 370 to 285 million USD. This study pioneered a vital new area for the economic assessment of fusion power plant: the economic performance on the deregulated electricity market. Results show that discussions based on simple LCOE would be inapplicable to deregulated markets, and the unplanned outage frequency target should be lowered on deregulated market. C. This paper aims to investigate techno-economic analysis of fusion-biomass hybrid model based on previously proposed technical and chemical concept. Fusion-biomass hybrid model, which takes no value of waste biomass from municipal, agricultural, and forestry areas as feedstock, produces synthetic gas generated by endothermic pyrolytic gasification using high temperature of fusion heat. Several blanket designs based on LiPb and SiC technology such as Dual Coolant Lithium Lead (DCLL) would be available for the heat over 700oC. Its technical extension is possible to perform biomass gasification of (C6H10O5 + H2O → 6H2+ 6CO -814 kJ) to produce chemical energy, synthetic gas. Produced synthetic gas can be converted into two different products; diesel and hydrogen. First, synthetic gas that contains hydrogen (H2) and carbon monoxide (CO) can be converted into diesel which is regarded as “carbon-neutral biofuel” by Fischer-Tropsch process (2H2+ CO → -CH2-+ H2O + 160kJ). The other is to produce hydrogen by water-gas shift reaction process (CO + H2O ↔ H2+ CO2 + 32 kJ). Carbon dioxide from water-gas shift reaction can be managed by carbon capture and sequestration technology. Underlying the technical and chemical process of fusion-biomass hybrid model, levelized cost of fuel for diesel and hydrogen is calculated as USD0.41/kg and USD1.21/kg, respectively. Breakeven price is USD0.73/kg for diesel and USD2.65/kg for hydrogen under the assumption of 1,000ton/day of fusion-biomass hybrid plant with 30-year lifetime. Sensitivity analysis is performed applying total capital investment, operation & maintenance cost, fuel production amount, operating time and fusion heat cost to understand the correlations between variables and fuel price. In addition to that, net present value after 30-year operation is calculated according to the change in fusion heat cost and fuel price, because technical structure and advancement highly affect fusion heat cost. Fusion-biomass hybrid model benefits in terms of environmental aspect by decreasing both waste biomass and CO2 emission. This study can provide guideline in targeting which fuel could be economically justified in the circumstances of variable environmental policy under different market demand and economical situations that would have a significant impacts on the designing of the fusion commercial reactors.

Speaker: Prof. satoshi konishi (kyoto university)

SEEKonishiRaporteur.pptx

summary konishi.pdf

774 Economic Performance of Fusion Power Plant on Future Deregulated Electricity Market

The economic performance of steady-state fusion power plants on future deregulated electricity markets was quantitatively analyzed for the first time with a newly constructed Simplified PJM Market Model. The results showed that (i) discussions based on simple levelised cost of electricity are insufficient for deregulated markets and (ii) the unplanned outage frequency target should be lowered to 0.3 times/year on deregulated market to achieve economic rationality of fusion power plants. Conventionally, the development strategies for fusion power plants came from extrapolation of past fission plant installation trends. However, due to the rapid transformations of the markets around the world, the future electricity markets will be significantly different from that of half a century ago. The fusion development strategies shall be revised accordingly: conventional measures such as levelised cost of electricity (LCOE) may no longer be applicable to future fusion power plants. To quantitatively analyze the economic performance of steady-state fusion power plants on future deregulated electricity markets, Simplified PJM Market Model that incorporates three Energy Market, Imbalance Fee and Ancillary Service Market was constructed. A steady-state fusion power plant with 1,200 MW electrical output (2,801 MW fusion) was assumed. The net present values (NPVs) of 40 years of plant operation were calculated with the discount rate of 1.7%. A sensitivity analyses were conducted for the unplanned outage frequency from 0.001 to 0.00001 times/hours. The economic performance of fusion power plant showed higher sensitivity to the unplanned outage frequency on deregulated market. The NPV of fusion plant on deregulated market would be devaluated from +368 million USD to -741 million USD when the unplanned outage frequency rises from 10-5 per hour to 10-4 per hour, while on conventional market, the devaluation would be only from 370 to 285 million USD. This study pioneered a vital new area for the economic assessment of fusion power plant: the economic performance on the deregulated electricity market. Results show that discussions based on simple LCOE would be inapplicable to deregulated markets, and the unplanned outage frequency target should be lowered on deregulated market.

Speaker: Prof. satoshi konishi (kyoto university)

180927IAEA-Summary.pdf

775 Techno-economic analysis of biodiesel and hydrogen production via Fusion-Biomass Hybrid Model

This paper aims to investigate techno-economic analysis of fusion-biomass hybrid model based on previously proposed technical and chemical concept. Fusion-biomass hybrid model, which takes no value of waste biomass from municipal, agricultural, and forestry areas as feedstock, produces synthetic gas generated by endothermic pyrolytic gasification using high temperature of fusion heat. Several blanket designs based on LiPb and SiC technology such as Dual Coolant Lithium Lead (DCLL) would be available for the heat over 700oC. Its technical extension is possible to perform biomass gasification of (C6H10O5 + H2O → 6H2+ 6CO -814 kJ) to produce chemical energy, synthetic gas. Produced synthetic gas can be converted into two different products; diesel and hydrogen. First, synthetic gas that contains hydrogen (H2) and carbon monoxide (CO) can be converted into diesel which is regarded as “carbon-neutral biofuel” by Fischer-Tropsch process (2H2+ CO → -CH2-+ H2O + 160kJ). The other is to produce hydrogen by water-gas shift reaction process (CO + H2O ↔ H2+ CO2 + 32 kJ). Carbon dioxide from water-gas shift reaction can be managed by carbon capture and sequestration technology. Underlying the technical and chemical process of fusion-biomass hybrid model, levelized cost of fuel for diesel and hydrogen is calculated as USD0.41/kg and USD1.21/kg, respectively. Breakeven price is USD0.73/kg for diesel and USD2.65/kg for hydrogen under the assumption of 1,000ton/day of fusion-biomass hybrid plant with 30-year lifetime. Sensitivity analysis is performed applying total capital investment, operation & maintenance cost, fuel production amount, operating time and fusion heat cost to understand the correlations between variables and fuel price. In addition to that, net present value after 30-year operation is calculated according to the change in fusion heat cost and fuel price, because technical structure and advancement highly affect fusion heat cost. Fusion-biomass hybrid model benefits in terms of environmental aspect by decreasing both waste biomass and CO2 emission. This study can provide guideline in targeting which fuel could be economically justified in the circumstances of variable environmental policy under different market demand and economical situations that would have a significant impacts on the designing of the fusion commercial reactors.

Speaker: Prof. Satoshi Konishi (Kyoto University)

Summary Slide.pptx

776 First demonstration of novel technique for disruption mitigation by core impurity deposition using shell pellets on DIII-D

Speaker: Dr Nicholas Eidietis (General Atomics)

IAEA18_Eidietis_Shell_v4_309.pdf

IAEA18_Eidietis_Shell_v4.pdf

PD/1-1 Eidietis Shell Abstract.pdf

PD/1-1 Eidietis Shell PrePrint.pdf

PD/1-1 Eidietis Shell Synopsis.pdf

777 WEST first plasma operation with all tungsten plasma facing components

Speaker: Jerome Bucalossi (CEA)

IAEA2018_WEST_Overview_Bucalossi.pdf

IAEA2018_WEST-v3.pptx

12:30 Lunch

S/1 Summary

778 The Nuclear Fusion Prize

Speakers: Richard Hawryluk (Princeton Plasma Physics Laboratory), Sophia Le Masurier

prize pres final-final.pptx

779 Summary EX/C, EX/S & PPC

Speaker: Dr David Campbell (ITER Organization)

IAEA-FEC-2018_Summary_EXC-EXS-PPC_Campbell_16-9.pptx

780 Summary EX/D, EX/W & ICC

Speaker: Dr Katsumi Ida (National Institute for Fusion Science (NIFS), Toki, Gifu, Japan)

summary IAEA-FEC EXW EXD ICC v3.pptx

781 Summary Magnetic Confinement Theory

Speaker: Prof. Ricardo Galvao (University of Sao Paulo)

Summary MCT R Galvao.pptx

16:00 Coffee Break

S/2 Summary

782 Summary Inertial Fusion Experiments and Theory

Speaker: Bahukutumbi P. Radha (University of Rochester)

Summary_IFE_Radha_FEC_2018_v1.pdf

783 Summary FIP, FNS, MPT & SEE

Speaker: Dr Takashi Inoue (JAEA Naka)

S-2-2_Inoue_Summary_FIP_FNS_MPT_SEE_181027r2.pptx

784 Closing Address

Speaker: IAEA Representative

785 Conference Closing

Speaker: Host Country Representative